Pioneer DEH-2200UB User manual

Owner’s Manual
Mode d’emploi
Manual de instrucciones
CD RECEIVER
AUTORADIO CD
RADIO CD
DEH-2200UB
English Français Español

Thank you for purchasing this PIONEER
product.
To ensure proper use, please read through this
manual before using this product. It is espe-
cially important that you read and observe
WARNINGs and CAUTIONs in this manual.
Please keep the manual in a safe and accessible
place for future reference.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interfer-
ence, and (2) this device must accept any inter-
ference received, including interference that
may cause undesired operation.
Information to User
Alteration or modifications carried out without
appropriate authorization may invalidate the
user’s right to operate the equipment.
For Canadian model
This Class B digital apparatus complies with
Canadian ICES-003.
About this unit
The tuner frequencies on this unit are allo-
cated for use in North America. Use in other
areas may result in poor reception.
WARNING
Handling the cord on this product or cords asso-
ciated with accessories sold with the product will
expose you to chemicals listed on proposition 65
known to the State of California and other govern-
mental entities to cause cancer and birth defect
or other reproductive harm. Wash hands after
handling.
CAUTION:
USE OF CONTROL OR ADJUSTMENT OR
PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
CAUTION:
THE USE OF OPTICAL INSTRUMENTS
WITH THIS PRODUCT WILL INCREASE
EYE HAZARD.
CAUTION
!Do not allow this unit to come into contact
with liquids. Electrical shock could result.
Also, damage to this unit, smoke, and over-
heating could result from contact with liquids.
!Always keep the volume low enough to hear
outside sounds.
!Avoid exposure to moisture.
!If the battery is disconnected or discharged,
any preset memory will be erased.
Important (Serial number)
The serial number is located on the bottom of
this unit. For your own security and convenience,
be sure to record this number on the enclosed
warranty card.
Before You Start
En
2
Presection

After-sales service for
Pioneer products
Please contact the dealer or distributor from
where you purchased this unit for after-sales
service (including warranty conditions) or any
other information. In case the necessary infor-
mation is not available, please contact the
companies listed below:
Please do not ship your unit to the companies
at the addresses listed below for repair without
advance contact.
U.S.A.
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
CANADA
Pioneer Electronics of Canada, Inc.
CUSTOMER SATISFACTION DEPARTMENT
300 Allstate Parkway
Markham, Ontario L3R 0P2
1-877-283-5901
905-479-4411
For warranty information please see the Lim-
ited Warranty sheet included with this unit.
In case of trouble
Should this unit fail to operate properly, please
contact your dealer or nearest authorized
PIONEER Service Station.
Visit our website
http://www.pioneerelectronics.com
!Learn about product updates (such as firm-
ware updates) for your product.
!Register your product to receive notices
about product updates and to safeguard
purchase details in our files in the event of
loss or theft.
!Access owner's manuals, spare parts infor-
mation, service information, and much
more.
Demo mode
Important
Failure to connect the red lead (ACC) of this unit
to a terminal coupled with ignition switch on/off
operations may lead to battery drain.
Demo mode
The demo automatically starts when the igni-
tion switch is set to ACC or ON while the unit
is turned off. Turning off the unit does not can-
cel demo mode. To cancel the demo mode,
press DISP//SCRL. Press DISP/ /SCRL
again to start. Operating the demo while the
ignition switch is set to ACC may drain battery
power.
Before You Start
En 3
English
Presection

Head unit









































Part Part
1DISP//SCRL 8AUX input jack (3.5
mm stereo jack)
2SRC/OFF 9USB port
3MULTI-CONTROL
(M.C.)a(list)
4Disc loading slot b1to 6
5h(eject) ca/b/c/d
6CLOCK dBAND/ESC
7Detach button
CAUTION
Use an optional Pioneer USB cable (CD-U50E) to
connect the USB audio player/USB memory to
the USB port. Since the USB audio player/USB
memory is projected forward from the unit, it is
dangerous to connect directly.
Do not use the unauthorized product.
Remote control






















Part Operation
eVOLUME Press to increase or decrease vo-
lume.
fMUTE Press to mute. Press again to un-
mute.
gAUDIO Press to select an audio function.
hDISP/SCRL
Press to select different displays.
Press and hold to scroll through
the text information.
iePress to pause or resume.
jFUNCTION
Press to select functions.
Press and hold to recall the initial
setting menu when the sources
are off.
kLIST/
ENTER
Press to display the disc title,
track title, folder, or file list de-
pending on the source.
While in the operating menu,
press to control functions.
Display indication




  


Indicator State
1(disc)
The disc (album) name is dis-
played.
Album search refinement on the
iPod browsing function is in use.
2(artist)
The disc (track) artist name is dis-
played.
Artist search refinement on the
iPod browsing function is in use.
3
Main dis-
play sec-
tion
!Tuner: band and frequency
!Built-in CD ,USB and iPod:
elapsed playback time and
text information
Operating this unit
En
4
Section
01

4(song)
The track (song) name is dis-
played.
A playable audio file has been se-
lected while operating the list.
Song search refinement on the
iPod browsing function is in use.
5cAn upper tier of folder or menu
exists.
6(folder) The list function is operated.
7d
A lower tier of folder or menu ex-
ists.
It flashes when a song/album re-
lated to the song currently playing
is selected from iPod.
8LOC The local seek tuning is on.
9LOUD
(loudness) The loudness is on.
a5(stereo) The selected frequency is being
broadcasted in stereo.
b(repeat) Track or folder repeat is on.
c(ran-
dom) Random play is on.
d(shuf-
fle)
Shuffle function is on while the
iPod source is being selected.
e(sound re-
triever)
The sound retriever function is
on.
Basic Operations
Important
!Handle gently when removing or attaching
the front panel.
!Avoid subjecting the front panel to excessive
shock.
!Keep the front panel out of direct sunlight and
high temperatures.
!Remove any cables and devices attached to
this unit before detaching the front panel to
avoid damage to the device or vehicle interior.
Removing the front panel to protect your unit from
theft
1Press the detach button to release the front
panel.
2Grab the front panel and remove.
Re-attaching the front panel
1Slide the front panel to the left until it clicks.
Front panel and the head unit are connected on
the left side. Make sure that the front panel has
been properly connected to the head unit.
2Press the right side of the front panel until it is
firmly seated.
If you can’t attach the front panel to the head unit
successfully, try again. However, forcing the front
panel into place may result in damage.
Turning the unit on
1Press SRC/OFF to turn the unit on.
Turning the unit off
1Press SRC/OFF and hold until the unit turns off.
Selecting a source
1Press SRC/OFF to cycle between:
TUNER (tuner)—CD (built-in CD player)—USB
(USB)/IPOD (iPod)—AUX (AUX)
Adjusting the volume
1Turn M.C. to adjust volume.
Notes
!When this unit’s blue/white lead is connected
to the vehicle’s auto-antenna relay control
terminal, the vehicle’s antenna extends when
this unit’s source is turned on. To retract the
antenna, turn the source off.
!In this manual, iPod and iPhone will be re-
ferred to as iPod.
Operating this unit
En 5
English
Section
01

Use and care of the remote
control
Using the remote control
1Point the remote control in the direction of the
front panel to operate.
When using for the first time, pull out the film
protruding from the tray.
Replacing the battery
1Slide the tray out on the back of the remote con-
trol.
2Insert the battery with the plus (+) and minus (–)
poles aligned properly.
WARNING
!Keep the battery out of the reach of children.
Should the battery be swallowed, consult a
doctor immediately.
!Batteries (battery pack or batteries installed)
must not be exposed to excessive heat such
as sunshine, fire or the like.
CAUTION
!Use one CR2025 (3 V) lithium battery.
!Remove the battery if the remote control is not
used for a month or longer.
!There is a danger of explosion if the battery is
incorrectly replaced. Replace only with the
same or equivalent type.
!Do not handle the battery with metallic tools.
!Do not store the battery with metallic objects.
!If the battery leaks, wipe the remote control
completely clean and install a new battery.
!When disposing of used batteries, comply
with governmental regulations or environmen-
tal public institutions’rules that apply in your
country/area.
!“Perchlorate Material –special handling may
apply.
See www.dtsc.ca.gov/hazardouswaste/
perchlorate. (Applicable to California, U.S.A.)”
Important
!Do not store the remote control in high tem-
peratures or direct sunlight.
!The remote control may not function properly
in direct sunlight.
!Do not let the remote control fall onto the
floor, where it may become jammed under the
brake or accelerator pedal.
Menu operations identical
for function settings/audio
adjustments/initial
settings/lists
Returning to the previous display
Returning to the previous list/category (the folder/ca-
tegory one level higher)
1Press DISP//SCRL.
Returning to the main menu
Returning to the top tier of list/category
1Press and hold DISP//SCRL.
Returning to the ordinary display
Canceling the initial setting menu
1Press BAND/ESC.
Returning to the ordinary display from the list/cate-
gory
1Press BAND/ESC.
Operating this unit
En
6
Section
01

Tuner
Basic Operations
Selecting a band
1Press BAND/ESC until the desired band (F1,F2,
F3 for FM or AM) is displayed.
Manual tuning (step by step)
1Press cor d.
Seeking
1Press and hold cor d, and then release.
You can cancel seek tuning by briefly pressing c
or d.
While pressing and holding cor d, you can skip
stations. Seek tuning starts as soon as you re-
lease cor d.
Storing and recalling stations
You can easily store up to six stations for each
band as presets.
%When you find a station that you want
to store in memory, press one of the preset
tuning buttons (1 to 6) and hold until the
preset number stops flashing.
Stored radio station frequency can be recalled
by pressing the preset tuning button.
#You can also recall stored radio stations by
pressing aor bduring the frequency display.
Function settings
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
After selecting, perform the following proce-
dures to set the function.
BSM (best stations memory)
BSM (best stations memory) automatically stores the
six strongest stations in the order of their signal
strength.
1Press M.C. to turn BSM on.
To cancel, press M.C. again.
LOCAL (local seek tuning)
Local seek tuning lets you tune in only those radio sta-
tions with sufficiently strong signals for good recep-
tion.
1Press M.C. to display the setting mode.
2Turn M.C. to select the desired setting.
FM: OFF—LEVEL 1—LEVEL 2—LEVEL 3—LEVEL
4
AM: OFF—LEVEL 1—LEVEL 2
Larger setting number is higher level. The highest
level setting allows reception of only the strongest
stations, while lower settings let you receive pro-
gressively weaker stations.
3Press M.C. to confirm the selection.
Note
Operation is complete even if the menu is can-
celled before being confirmed.
CD/CD-R/CD-RW and USB
storage devices
Basic Operations
Playing a CD/CD-R/CD-RW
1Insert the disc, label side up, into the disc loading
slot.
1If a disc has already been inserted, press SRC/
OFF to select the built-in CD player.
Ejecting a CD/CD-R/CD-RW
1Press h.
Playing songs on a USB storage device
1Open the USB connector cover and plug in the
USB storage device using a USB cable.
Stop playing a USB storage device
1You may disconnect the USB storage device at
anytime.
Selecting a folder
1Press aor b.
Selecting a track
1Press cor d.
Fast forwarding or reversing
1Press and hold cor d.
Operating this unit
En 7
English
Section
01

Returning to root folder
1Press and hold BAND/ESC.
Switching between compressed audio and CD-DA
1Press BAND/ESC.
Notes
!When playing compressed audio, there is no
sound during fast forward or reverse.
!USB portable audio players that can be
charged via USB will be recharged when
plugged in and the ignition switch is set to
ACC or ON.
!Disconnect USB storage device from unit
when not in use.
!If plug and play is on and a USB storage de-
vice is present, depending on the type of de-
vice, the source may switch to USB
automatically when you turn on the engine.
Please change plug and play setting as neces-
sary. Refer to USB (plug and play) on page 12.
Displaying text information
Selecting the desired text information
1Press DISP//SCRL.
CD TEXT discs: Play time—disc title—disc ar-
tist name—track title—track artist name
WMA/MP3: Play time—folder name—file name
—track title—artist name—album title—com-
ment—bit rate—folder and track numbers
WAV: Play time—folder name—file name—sam-
pling frequency—folder and track numbers
Scrolling the text information to the left
1Press and hold DISP//SCRL.
Notes
!Incompatible text stored with the audio file
may not be displayed or may be displayed in-
correctly.
!Depending on the version of iTunes used to
write MP3 files onto a disc, comment informa-
tion may be incorrectly displayed.
!When playing back VBR (variable bit rate)-re-
corded WMA files, the average bit rate value is
displayed.
!When playing back VBR (variable bit rate)-re-
corded MP3 files, VBR is displayed instead of
bit rate value.
Selecting and playing files/
tracks from the name list
1 Press to switch to the file/track
name list mode.
2 Use M.C. to select the desired file name
(or folder name).
Changing file or folder name
1Turn M.C.
Playing
1When a file or track is selected, press M.C.
Seeing a list of files (or folders) in the selected folder
1When a folder is selected, press M.C.
Playing a song in the selected folder
1When a folder is selected, press and hold M.C.
Note
Track title list will display the list of track titles on
a CD TEXT disc.
Advanced operations using
special buttons
Selecting a repeat play range
1Press 6/to cycle between the following:
CD/CD-R/CD-RW
!DISC –Repeat all tracks
!TRACK –Repeat the current track
!FOLDER –Repeat the current folder
USB audio player/USB memory
!TRACK –Repeat the current file
!FOLDER –Repeat the current folder
!ALL –Repeat all files
Playing tracks in random order
1Press 5/to turn random play on or off.
Tracks in a selected repeat range are played in
random order.
Operating this unit
En
8
Section
01

Pausing playback
1Press 2/PAUSE to pause or resume.
Enhancing compressed audio and restoring rich
sound (sound retriever)
1Press 1/S.Rtrv to cycle between:
OFF (off)—1—2
1is effective for low compression rates, and 2is
effective for high compression rates.
Function settings
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
After selecting, perform the following proce-
dures to set the function.
REPEAT (repeat play)
1Press M.C. to display the setting mode.
2Turn M.C. to select a repeat play range.
For details, refer to Selecting a repeat play range on
the previous page.
3Press M.C. to confirm the selection.
RANDOM (random play)
1Press M.C. to turn random play on or off.
PAUSE (pause)
1Press M.C. to pause or resume.
S.RTRV (sound retriever)
Automatically enhances compressed audio and re-
stores rich sound.
1Press M.C. to display the setting mode.
2Turn M.C. to select the desired setting.
For details, refer to Enhancing compressed audio
and restoring rich sound (sound retriever) on this
page.
3Press M.C. to confirm the selection.
Note
Operation is complete even if the menu is can-
celled before being confirmed.
iPod
Basic Operations
Playing songs on iPod
1Open the USB connector cover and plug in an
iPod using the iPod Dock Connector to USB
Cable.
Selecting a track (chapter)
1Press cor d.
Fast forwarding or reversing
1Press and hold cor d.
Notes
!The iPod’s battery will be charged if the igni-
tion switch is set to ACC or ON, while con-
nected.
!While the iPod is connected to this unit, the
iPod cannot be turned on or off unless the
control mode is set to IPOD.
!Disconnect headphones from the iPod before
connecting to this unit.
!The iPod will turn off about two minutes after
the ignition switch is set to OFF.
Displaying text information
Selecting the desired text information
1Press DISP//SCRL.
Play time—song title—artist name—album title
—number of songs
Scrolling the text information to the left
1Press and hold DISP//SCRL.
Note
Incompatible text saved on the iPod will not be
displayed by the unit.
Browsing for a song
1 Press to switch to the top menu of
the list search.
Operating this unit
En 9
English
Section
01

2 Use M.C. to select a category/song.
Changing the name of song or category
1Turn M.C.
PLAYLISTS (playlists)—ARTISTS (artists)—AL-
BUMS (albums)—SONGS (songs)—PODCASTS
(podcasts)—GENRES (genres)—COMPOSERS
(composers)—AUDIOBOOKS (audiobooks)
Playing
1When a song is selected, press M.C.
Seeing a list of songs in the selected category
1When a category is selected, press M.C.
Playing a song in the selected category
1When a category is selected, press and hold M.C.
Searching by alphabet in the list
1When a list for the selected category is displayed,
press to switch to alphabet search mode.
2Turn M.C. to select a letter.
3Press M.C. to display the alphabetical list.
If alphabet search is aborted, NOT FOUND is dis-
played.
Note
Depending on the number of files in the iPod,
there may be a delay when displaying a list.
Advanced operations using
special buttons
Selecting a repeat play range
1Press 6/to cycle between the following:
!ONE –Repeat the current song
!ALL –Repeat all songs in the selected list
Playing all songs in a random order (shuffle all)
1Press 5/to turn shuffle all on.
Pausing playback
Refer to Pausing playback on the previous page.
Playing songs related to the currently playing song
You can play songs from the following lists.
!Album list of currently playing artist
!Song list of currently playing album
!Album list of currently playing genre
1Press and hold M.C. to switch to the link play
mode.
2Turn M.C. to change the mode; press to select.
!ARTIST –Plays an album of currently playing
artist.
!ALBUM –Plays a song of currently playing
album.
!GENRE –Plays an album of currently playing
genre.
The selected song/album will be played after the
currently playing song.
The selected song/album may be cancelled if you op-
erate functions other than link search (e.g. fast for-
ward and reverse).
If no related albums/songs are found, NOT FOUND
is displayed.
Depending on the song selected to play, the end of
the currently playing song and the beginning of the
selected song/album may be cut off.
Operating this unit’s iPod function from your iPod
This function is not compatible with the following
iPod models.
!iPod nano 1st generation
!iPod 5th generation
This unit’s iPod function allows you to conduct opera-
tions from your iPod and listen to it using your car’s
speakers.
1Press 4/IPOD to switch the control mode.
!IPOD –This unit’s iPod function can be oper-
ated from the connected iPod.
!AUDIO –This unit’s iPod function can be op-
erated from this unit.
Enhancing compressed audio and restoring rich
sound (sound retriever)
Refer to Enhancing compressed audio and restoring
rich sound (sound retriever) on the previous page.
Function settings
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
After selecting, perform the following proce-
dures to set the function.
Operating this unit
En
10
Section
01

REPEAT (repeat play)
!Refer to REPEAT (repeat play) on page 9.
However the repeat range is different from CD/
USB storage device. Refer to Selecting a repeat
play range on the previous page.
SHUFFLE (shuffle)
1Press M.C. to display the setting mode.
2Turn M.C. to select your favorite setting.
!SONGS –Play back songs in the selected list
in random order.
!ALBUMS –Play back songs from a randomly
selected album in order.
!OFF –Cancel random play.
3Press M.C. to confirm the selection.
SHUFFLE ALL (shuffle all)
1Press M.C. to turn shuffle all on.
To turn off, set SHUFFLE in the FUNCTION menu
to off.
LINK PLAY (link play)
1Press M.C. to display the setting mode.
2Turn M.C. to change the mode; press to select.
For details about the settings, refer to Playing
songs related to the currently playing song on the
previous page.
CTRL (control mode)
1Press M.C. to select your favorite setting.
For details about the settings, refer to Operating
this unit’s iPod function from your iPod on the pre-
vious page.
PAUSE (pause)
!Refer to PAUSE (pause) on page 9.
AUDIO BOOK (audiobook speed)
The playback speed of audiobook can be changed.
1Press M.C. to display the setting mode.
2Turn M.C. to select your favorite setting.
!FASTER –Playback faster than normal speed
!NORMAL –Playback in normal speed
!SLOWER –Playback slower than normal
speed
3Press M.C. to confirm the selection.
S.RTRV (sound retriever)
!Refer to S.RTRV (sound retriever) on page 9.
Notes
!Operation is complete even if the menu is can-
celled before being confirmed.
!Switching the control mode to IPOD pauses
song playback. Operate the iPod to resume
playback.
!The following functions are still accessible
from the unit even if the control mode is set to
IPOD.
—Volume
—Fast forward/reverse
—Track up/down
—Pausing
—Switching the text information
!When the control mode is set to IPOD, opera-
tions are limited as follows:
—Only CTRL (control mode), PAUSE (pause)
and S.RTRV (sound retriever) functions are
available.
—Browse function cannot be operated from
this unit.
Audio Adjustments
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select AUDIO.
3 Turn M.C. to select the audio function.
After selecting, perform the following proce-
dures to set the audio function.
FAD/BAL (fader/balance adjustment)
You can change the fader/balance setting.
1Press M.C. to display the setting mode.
2Press M.C. to cycle between fader and balance.
3Turn M.C. to adjust speaker balance.
Adjustment range (front/rear): F15 to R15
Adjustment range (left/right): L15 to R15
FR 0 is the proper setting when only two speakers
are used.
EQUALIZER (equalizer recall)
Operating this unit
En 11
English
Section
01

There are six stored settings DYNAMIC (dynamic),
VOCAL (vocal), NATURAL (natural), CUSTOM (cus-
tom), FLAT (flat) and POWERFUL (powerful).
!When FLAT is selected no adjustments are made
to the sound.
1Press M.C. to display the setting mode.
2Turn M.C. to select the equalizer.
DYNAMIC—VOCAL—NATURAL—CUSTOM—
FLAT—POWERFUL
3Press M.C. to confirm the selection.
TONE CTRL (equalizer adjustment)
You can adjust the bass/mid/treble level.
!Adjusted equalizer curve settings are stored in
CUSTOM.
1Press M.C. to display the setting mode.
2Press M.C. to select BASS (bass)/MID (mid)/TRE-
BLE (treble).
3Turn M.C. to adjust the level.
Adjustment range: +6 to -6
LOUDNESS (loudness)
Loudness compensates for deficiencies in the low-
and high-frequency ranges at low volume.
1Press M.C. to display the setting mode.
2Turn M.C. to select the desired setting.
OFF (off)—LOW(low)—HIGH (high)
3Press M.C. to confirm the selection.
SLA (source level adjustment)
SLA (Source level adjustment) lets you adjust the vo-
lume level of each source to prevent radical changes
in volume when switching between sources.
!Settings are based on the FM volume level, which
remains unchanged.
Before adjusting source levels, compare the FM
volume level with the level of the source you wish
to adjust.
!The AM volume level can also be adjusted with
source level adjustments.
1Press M.C. to display the setting mode.
2Turn M.C. to adjust the source volume.
Adjustment range: +4 to –4
3Press M.C. to confirm the selection.
Notes
!When selecting FM as the source, you cannot
switch to SLA.
!Operation is complete even if the menu is can-
celled before being confirmed.
Initial Settings
1 Press SRC/OFF and hold until the unit
turns off.
2 Press M.C. and hold until CLOCK SET ap-
pears in the display.
3 Turn M.C. to select the initial setting.
After selecting, perform the following proce-
dures to set the initial setting.
CLOCK SET (setting the clock)
1Press M.C. to display the setting mode.
2Press M.C. to select the segment of the clock dis-
play you wish to set.
Hour—Minute
As you select segments of the clock display, the
selected segment flashes.
3Turn M.C. to adjust the clock.
AUX (auxiliary input)
Activate this setting when using auxiliary device con-
nected to this unit.
1Press M.C. to turn AUX on or off.
USB (plug and play)
This setting allows you to switch your source to USB/
IPOD automatically.
1Press M.C. to turn the plug and play on or off.
ON –When USB storage device/iPod is con-
nected, the source is automatically switched to
USB/IPOD. If you disconnect your USB storage
device/iPod, this unit’s source is turned off.
OFF –When USB storage device/iPod is con-
nected, the source is not switched to USB/IPOD
automatically. Please change the source to USB/
IPOD manually.
ILLUMI (illumination color)
You can select the desired illumination color.
1Press M.C. to display the setting mode.
2Turn M.C. to select the desired setting.
RED (red)—GREEN (green)
3Press M.C. to confirm the selection.
Note
Operation is complete even if the menu is can-
celled before being confirmed.
Operating this unit
En
12
Section
01

Using the AUX source
1 Insert the stereo mini plug into the
AUX input jack.
2 Press SRC/OFF to select AUX as the
source.
Note
AUX cannot be selected unless the auxiliary set-
ting is turned on. For more details, refer to AUX
(auxiliary input) on the previous page.
Turning the clock display
on or off
%Press CLOCK to turn the clock display
on or off.
Note
The clock display disappears temporarily when
you perform other operations, but the clock dis-
play appears again after 25 seconds.
Operating this unit
En 13
English
Section
01

WARNING
!Use speakers over 50 W (output value) and be-
tween 4 Wto 8 W(impedance value). Do not
use 1 Wto 3 Wspeakers for this unit.
!The black cable is ground. When installing
this unit or power amp (sold separately), make
sure to connect the ground wire first. Ensure
that the ground wire is properly connected to
metal parts of the car’s body. The ground wire
of the power amp and the one of this unit or
any other device must be connected to the car
separately with different screws. If the screw
for the ground wire loosens or falls out, it
could result in fire, generation of smoke or
malfunction.
Ground wire
Metal parts of car’s body
Other devices
(Another electronic
device in the car)
POWER AMP
Important
!When installing this unit in a vehicle without
an ACC (accessory) position on the ignition
switch, failure to connect the red cable to the
terminal that detects operation of the ignition
key may result in battery drain.
O
N
S
T
A
R
T
O
F
F
ACC position No ACC position
!Use this unit with a 12-volt battery and nega-
tive grounding only. Failure to do so may result
in a fire or malfunction.
!To prevent a short-circuit, overheating or mal-
function, be sure to follow the directions
below.
—Disconnect the negative terminal of the
battery before installation.
—Secure the wiring with cable clamps or ad-
hesive tape. Wrap adhesive tape around
wiring that comes into contact with metal
parts to protect the wiring.
—Place all cables away from moving parts,
such as the gear shift and seat rails.
—Place all cables away from hot places,
such as near the heater outlet.
—Do not connect the yellow cable to the bat-
tery by passing it through the hole to the
engine compartment.
—Cover any disconnected cable connectors
with insulating tape.
—Do not shorten any cables.
—Never cut the insulation of the power cable
of this unit in order to share the power
with other devices. The current capacity of
the cable is limited.
—Use a fuse of the rating prescribed.
—Never wire the negative speaker cable di-
rectly to ground.
—Never band together negative cables of
multiple speakers.
!When this unit is on, control signals are sent
through the blue/white cable. Connect this
cable to the system remote control of an exter-
nal power amp or the vehicle’s auto-antenna
relay control terminal (max. 300 mA 12 V DC).
If the vehicle is equipped with a glass anten-
na, connect it to the antenna booster power
supply terminal.
!Never connect the blue/white cable to the
power terminal of an external power amp.
Also, never connect it to the power terminal of
the auto antenna. Doing so may result in bat-
tery drain or a malfunction.
Connections
En
14
Section
02

Connection diagram












Connect with RCA cables
(sold separately)
Rear output
This product
Antenna jack
Fuse (10 A)
Blue/white
Connect to system control terminal of the
power amp or auto-antenna relay control
terminal (max. 300 mA 12 V DC).
Yellow
Connect to the constant 12 V
supply terminal.
Red
Connect to terminal controlled
by ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free
metal location.
Power amp
(sold separately)
System remote control
Left Right
Perform these connections when using
the optional amplifier.
Rear speaker Rear speaker
White/black
Violet/black
Violet
With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.
Front speaker Front speaker
White
Gray/black
Gray
Green/black
Green
Rear speaker Rear speaker
Connections
En 15
English
Section
02

Important
!Check all connections and systems before
final installation.
!Do not use unauthorized parts as this may
cause malfunctions.
!Consult your dealer if installation requires dril-
ling of holes or other modifications to the vehi-
cle.
!Do not install this unit where :
—it may interfere with operation of the vehi-
cle.
—it may cause injury to a passenger as a re-
sult of a sudden stop.
!The semiconductor laser will be damaged if it
overheats. Install this unit away from hot
places such as near the heater outlet.
!Optimum performance is obtained when the
unit is installed at an angle of less than 60°.
60°
DIN front/rear mount
This unit can be properly installed either from
“Front”(conventional DIN front-mount) or
“Rear”(DIN rear-mount installation, utilizing
threaded screw holes on the sides of unit
chassis). For details, refer to the following in-
stallation methods.
DIN Front-mount
1 Insert the mounting sleeve into the
dashboard.
For installation in shallow spaces, use the sup-
plied mounting sleeve. If there is enough
space, use the mounting sleeve that came
with the vehicle.
2 Secure the mounting sleeve by using a
screwdriver to bend the metal tabs (90°)
into place.
Dashboard
Mounting sleeve
3 Install the unit as illustrated.
Use commercially available parts when instal-
ling.
Screw (M48)
Screw Metal strap
Nut
Firewall or
metal support
#Make sure that the unit is installed securely in
place. An unstable installation may cause skip-
ping or other malfunctions.
DIN Rear-mount
1 Determine the appropriate position
where the holes on the bracket and the
side of the unit match.
Installation
En
16
Section
03

2 Tighten two screws on each side.
Screw
Mounting bracket Dashboard or console
!Use either truss (5 mm × 8 mm) or flush
surface (5 mm × 9 mm) screws, depending
on the bracket screw holes.
Removing the unit
1 Extend top and bottom of the trim ring
outwards to remove the trim ring. (When
reattaching the trim ring, point the side
with the groove down.)
Trim ring
!Releasing the front panel allows easier ac-
cess to the trim ring.
2 Insert the supplied extraction keys into
both sides of the unit until they click into
place.
3 Pull the unit out of the dashboard.
Fastening the front panel
If you do not plan to detach the front panel,
the front panel can be fastened with the sup-
plied screw.
Screw
Installation
En 17
English
Section
03

Troubleshooting
Symptom Cause Action
The display
automatically
returns to the
ordinary dis-
play.
You did not per-
form any opera-
tion within about
30 seconds.
Perform operation
again.
The repeat play
range changes
unexpectedly.
Depending on
the repeat play
range, the se-
lected range may
change when se-
lecting another
folder or track, or
when fast for-
warding/rever-
sing.
Select the repeat
play range again.
A subfolder is
not played
back.
Subfolders can-
not be played
when FOLDER
(folder repeat) is
selected.
Select another re-
peat play range.
NO XXXX ap-
pears when a
display is chan-
ged (e.g., NO
TITLE).
No text informa-
tion embedded
Switch the display
or play another
track/file.
The display is
illuminated
when the unit
is turned off.
Demo mode is
on.
Press DISP//
SCRL to cancel
demo mode.
The unit is mal-
functioning.
There is inter-
ference.
You are using a
device, such as a
cell phone, that
transmits electro-
magnetic waves
near the unit.
Move electrical de-
vices that may be
causing the inter-
ference away from
the unit.
Error messages
When you contact your dealer or your nearest
Pioneer Service Center, be sure to note the
error message.
Built-in CD Player
Message Cause Action
ERROR-11, 12,
17, 30
Dirty disc Clean disc.
Scratched disc Replace disc.
ERROR-10, 11,
12, 15, 17, 30,
A0
Electrical or me-
chanical
Turn the ignition
switch OFF and
back ON, or switch
to a different
source, then back
to the CD player.
ERROR-15 The inserted disc
is blank
Replace disc.
ERROR-22, 23 Unsupported CD
format
Replace disc.
FRMT READ There is some-
times a delay be-
tween the start of
playback and
when you start to
hear any sound
Wait until the mes-
sage disappears
and you hear
sound.
NO AUDIO The inserted disc
does not contain
any playable files
Replace disc.
SKIPPED The inserted disc
contains DRM
protected WMA
files
Replace disc.
PROTECT All the files on
the inserted disc
are embedded
with DRM
Replace disc.
USB storage device
Message Cause Action
NO DEVICE When plug and
play is off, no
USB storage de-
vice is con-
nected.
!Turn the plug
and play on.
!Connect a com-
patible USB sto-
rage device.
FRMT READ There is some-
times a delay be-
tween the start of
playback and
when you start to
hear any sound
Wait until the mes-
sage disappears
and you hear
sound.
Additional Information
En
18
Appendix

NO AUDIO
No songs Transfer the audio
files to the USB
storage device and
connect.
The connected
USB storage de-
vice has security
enabled
Follow the USB
storage device in-
structions to dis-
able the security.
SKIPPED The connected
USB storage de-
vice contains
WMA files em-
bedded with
Windows Med-
iaäDRM 9/10
Play an audio file
not embedded with
Windows Media
DRM 9/10.
PROTECT All the files in the
USB storage de-
vice are em-
bedded with
Windows Media
DRM 9/10
Transfer audio files
not embedded with
Windows Media
DRM 9/10 to the
USB storage de-
vice and connect.
N/A USB The USB storage
device connected
to is not sup-
ported by this
unit.
Connect a USB
Mass Storage
Class compliant
device.
CHECK USB The USB connec-
tor or USB cable
has short-
circuited.
Check that the
USB connector or
USB cable is not
caught in some-
thing or damaged.
The connected
USB storage de-
vice consumes
more than 500
mA (maximum
allowable cur-
rent).
Disconnect the
USB storage de-
vice and do not
use it. Turn the
ignition switch to
OFF, then to ACC
or ON and then
connect only com-
pliant USB storage
devices.
ERROR-18 Not compatible
USB device
Disconnect your
device and replace
it with a compati-
ble USB storage
device.
ERROR-19
Communication
failure
Perform one of the
following opera-
tions.
–Turn the ignition
switch OFF and
back ON.
–Disconnect or
eject the USB sto-
rage device.
–Change to a dif-
ferent source.
Then, return to the
USB source.
ERROR-23 USB storage de-
vice is not for-
matted with
FAT16 or FAT32
USB storage de-
vice should be for-
matted with FAT16
or FAT32.
iPod
Message Cause Action
NO DEVICE When plug and
play is off, no
USB storage de-
vice or iPod is
connected.
!Turn the plug
and play on.
!Connect a com-
patible iPod.
FRMT READ There is some-
times a delay be-
tween the start of
playback and
when you start to
hear any sound
Wait until the mes-
sage disappears
and you hear
sound.
ERROR-19 Communication
failure
Disconnect the
cable from iPod.
Once iPod’s main
menu is displayed,
reconnect cable.
Reset the iPod.
iPod failure Disconnect the
cable from iPod.
Once iPod’s main
menu is displayed,
reconnect cable.
Reset the iPod.
ERROR-16, 18 Old iPod firm-
ware versions
Update the iPod
version.
iPod failure Disconnect the
cable from iPod.
Once iPod’s main
menu is displayed,
reconnect cable.
Reset the iPod.
Additional Information
En 19
English
Appendix

CHECK USB
iPod operates
correctly but
does not charge
Check if the con-
nection cable for
iPod shorted out
(e.g., not caught in
metal objects).
After checking,
turn the ignition
switch OFF and
back ON or discon-
nect the iPod and
reconnect.
NO SONGS No songs Transfer songs to
iPod.
STOP No songs in the
current list
Select a list that
contains songs.
Handling guideline
Discs and player
Use only discs featuring either of following two logos.
Use 12-cm disc. Do not use 8-cm disc or an adapter
for 8-cm disc.
Use only conventional, fully circular discs. Do not use
shaped discs.
Do not insert anything other than a CD into the CD
loading slot.
Do not use cracked, chipped, warped, or otherwise
damaged discs as they may damage the player.
Unfinalized CD-R/CD-RW disc playback is not possi-
ble.
Do not touch the recorded surface of the discs.
Store discs in their cases when not in use.
Avoid leaving discs in excessively hot environments
including under direct sunlight.
Do not attach labels, write on or apply chemicals to
the surface of the discs.
To clean a CD, wipe the disc with a soft cloth outward
from the center.
Condensation may temporarily impair the player’s
performance. Leave it to adjust to the warmer tem-
perature for about one hour. Also, wipe any damp
discs with a soft cloth.
Playback of discs may not be possible because of
disc characteristics, disc format, recorded applica-
tion, playback environment, storage conditions, and
so on.
Road shocks may interrupt disc playback.
Read the precautions for discs before using them.
USB storage device
Address any questions you have about your USB sto-
rage device to the manufacturer of the device.
Connections via a USB hub are not supported.
Do not connect anything other than a USB storage
device.
Do not leave the USB storage device in any place with
high temperatures.
Firmly secure the USB storage device when driving.
Do not let the USB storage device fall onto the floor,
where it may become jammed under the brake or ac-
celerator pedal.
Depending on the USB storage device, the following
problems may occur.
!Operations may vary.
!This unit may not recognize the storage device.
!The file may not be played back properly.
!The device may generate noise in the radio.
iPod
Do not leave the iPod in direct sunlight for extended
amounts of time. Extended exposure to direct sun-
light can result in iPod malfunction due to the result-
ing high temperature.
Do not leave the iPod in any place with high tempera-
tures.
To ensure proper operation, connect the dock connec-
tor cable from the iPod directly to this unit.
Additional Information
En
20
Appendix