Pioneer DEH-P3370XM UC User manual

Note:
• This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recre-
ational vehicle, truck or bus, check the battery
voltage.
• To avoid shorts in the electrical system, be sure to
disconnect the ≠battery cable before beginning
installation.
• Refer to the owner’s manual for details on con-
necting the power amp and other units, then make
connections correctly.
• Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
• Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake and
seat rails. Do not route wiring in places that get
hot, such as near the heater outlet. If the insulation
of the wiring melts or gets torn, there is a danger of
the wiring short-circuiting to the vehicle body.
• Don’t pass the yellow lead through a hole into the
engine compartment to connect to the battery. This
will damage the lead insulation and cause a very
dangerous short.
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.
• When replacing fuse, be sure to use only fuse of
the rating prescribed on this unit and the fuse hold-
er.
• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right ≠speaker leads are common.
• Speakers connected to this unit must be high-
power types with minimum rating of 50 W and
impedance of 4 to 8 ohms. Connecting speakers
with output and/or impedance values other than
those noted here may result in the speakers catch-
ing fire, emitting smoke, or becoming damaged.
• When this product’s source is switched ON, a con-
trol signal is output through the blue/white lead.
Connect to an external power amp’s system remote
control or the car’s Auto-antenna relay control ter-
minal (max. 300 mA 12 V DC). If the car features
a glass antenna, connect to the antenna booster
power supply terminal.
• When an external power amp is being used with
this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do not
connect the blue/white lead to the power terminal
of the auto-antenna. Such connection could cause
excessive current drain and malfunction.
• To avoid short-circuiting, cover the disconnected
lead with insulating tape. Especially, insulate the
unused speaker leads without fail. There is a possi-
bility of short-circuiting if the leads are not insulat-
ed.
• To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same colors
correctly.
• If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be connected
to a terminal coupled with ignition switch ON/OFF
operations. If this is not done, the vehicle battery
may be drained when you are away from the vehi-
cle for several hours. (Fig. 1)
Fig. 1
• The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the ground
becomes detached, there is a risk of damage to the
products or fire.
• Cords for this product and those for other prod-
ucts may be different colors even if they have the
same function. When connecting this product to
another product, refer to the supplied Installation
manuals of both products and connect cords that
have the same function.
No ACC positionACC position
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F
Connecting the Units
INSTALLATION MANUAL
INSTALLATION MANUAL
<KYMFZ/01G00000>
DEH-P3370XM
Printed in Japan
<CRB1735-A> UC
This product conforms to CEMA cord colors.
Connecting the Tuner Unit (Fig. 2)
Fig. 2
IP-BUS cable
To IP-BUS Input
(Blue)
Yellow
To terminal always supplied with power
regardless of ignition switch position.
Black (ground)
To vehicle (metal) body.
Fuse holder
IP-BUS Output
(Black)
This Unit
Antenna Input
Power Supply
IP-BUS Input
(Blue)
Multi-CD player
(sold separately)
Green
(Terrestrial)
Yellow (Satellite)
Black
6m
To Head Unit
(Refer to Fig. 3.)
Antenna Unit
(AN-90XM)
(sold separately)

Connecting the Units
Fig. 3
System remote control
Right
Front speaker
White Gray
White/black
Green
Green/black
Gray/black
Violet
Violet/black
Front speaker
Left
Rear speaker
or Subwoofer Rear speaker or Subwoofer
Rear speaker
or Subwoofer Rear speaker or Subwoofer
Fuse
IP-BUS cable
IP-BUS input (Blue)
This Product
Antenna jack
Rear or Subwoofer output
Note:
When a subwoofer is connected to this unit instead of a rear speaker,
change the rear output setting in the Initial Setting. (Refer to the
Operation Manual.) The subwoofer output of this unit is monaural.
Red
To electric terminal controlled by ignition
switch (12 V DC) ON/OFF.
Black (ground)
To vehicle (metal) body.
Yellow
To terminal always supplied with power
regardless of ignition switch position.
To Tuner unit
(Refer to Fig. 2.)
Orange/white
To lighting switch terminal.
Blue/white
To system control terminal of the power
amp or Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
Power amp
(sold separately)
Connecting cords with RCA pin plugs
(sold separately)
Perform these connections when using a
different amp (sold separately).
With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.
Connecting the Head Unit (Fig. 3) Protect the Antenna Connector
Fig. 4
Screw (3 ×6 mm)

DIN Front/Rear-mount
This unit can be properly installed either from “Front” (conventional DIN Front-mount) or
“Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit
chassis). For details, refer to the following illustrated installation methods.
DIN Front-mount
Installation with the rubber bush (Fig. 6)
Fig. 6
Holder
After inserting the holder into the dash-
board, then select the appropriate tabs
according to the thickness of the dash-
board material and bend them.
(Install as firmly as possible using the
top and bottom tabs. To secure, bend
the tabs 90 degrees.)
182
53 Rubber bush
Screw
Dashboard
Installation
Note:
• Before finally installing the unit, connect the
wiring temporarily, making sure it is all connected
up properly, and the unit and the system work
properly.
• Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
can cause malfunctions.
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
of the vehicle.
• Install the unit where it does not get in the driver’s
way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
• The semiconductor laser will be damaged if it
overheats, so don’t install the unit anywhere hot
— for instance, near a heater outlet.
• If installation angle exceeds 60° from horizontal,
the Head Unit might not give its optimum perfor-
mance. (Fig. 5)
Fig. 5
• When mounting this unit, make sure none of the
leads are trapped between this unit and the sur-
rounding metalwork or fittings.
• Do not mount the tuner unit near the heater outlet,
where it would be affected by heat, or near the
doors, where rainwater might splash onto it.
• Before drilling any mounting holes always check
behind where you want to drill the holes. Do not
drill into the gas line, brake line, electrical wiring
or other important parts.
• If the tuner unit is installed in the passenger com-
partment, anchor it securely so it does not break
free while the car is moving, and cause injury or an
accident.
• If the tuner unit is installed under a front seat,
make sure it does not obstruct seat movement.
Route all leads and cords carefully around the slid-
ing mechanism so they do not get caught or
pinched in the mechanism and cause a short cir-
cuit.
60°
Removing the Unit (Fig. 7) (Fig. 8)
Fig. 7
Fig. 8
5
6
Insert the release pin into the hole in
the bottom of the frame and pull out
to remove the frame.
(When reattaching the frame, point
the side with a groove downwards
and attach it.)
Frame
Insert the supplied extraction keys
into the unit, as shown in the figure,
until they click into place. Keeping
the keys pressed against the sides of
the unit, pull the unit out.

Installing the Tuner Unit
Mounting with Brackets (Fig. 15)
Fig. 15
Screw (4 ×6 mm)
Car mat or chassis Bracket
Tapping screw (4 ×12 mm)
Drill 2 to 2.5 mm diameter holes.
Installation
Fixing the Front Panel
If you do not operate the Detaching and Replacing the Front Panel Function, use the sup-
plied fixing screws and holder to fix the front panel to this unit.
1. Attach the holder to the front panel. (Fig. 12)
Fig. 12
2. Replace the front panel to the unit. (Fig. 13)
Fig. 13
3. Fix the front panel to the unit using fixing screws. (Fig. 14)
Fig. 14
Fixing screw
DIN Rear-mount
Installation using the screw holes on the side of the unit
1. Remove the frame. (Fig. 9)
Fig. 9
2. Fastening the unit to the factory radio mounting bracket.
(Fig. 10) (Fig. 11)
Select a position where the screw holes of the bracket and
the screw holes of the head unit become aligned (are fitted),
and tighten the screws at 2 places on each side. Use either
truss screws (5 ×8 mm) or flush surface screws
(5 ×9 mm), depending on the shape of the screw holes in
the bracket.
Fig. 10
Fig. 11
11
13
12
10
8
9
Frame
Screw
Dashboard or Console
Factory radio mounting bracket
Insert the release pin into the hole in
the bottom of the frame and pull out
to remove the frame.
(When reattaching the frame, point
the side with a groove downwards
and attach it.)