Pioneer DEH-P710BT - Premier Radio / CD User manual

English Français Español
<0G020184B> <1>
Installation Manual
Manuel d’installation
Manual de instalación
CD RECEIVER
AUTORADIO CD
REPRODUCTOR DE CD
DEH-P710BT

2
<0G020184B> <2>
Contents Connecting the units
Connecting the units ............................ 2
Connecting the power cord ............................... 4
When using a subwoofer
without using the optional amplifier ........ 6
When connecting to
separately sold power amp........................ 8
When connecting speakers
without using the internal amplifier ....... 10
Installation ........................................... 12
DIN Front/Rear-mount................................... 12
Removing or attaching the trim ring .................... 12
DIN Front-mount .................................................... 13
DIN Rear-mount ..................................................... 13
Fastening the front panel .............................. 14
Installing the microphone............................. 14
When installing the microphone
on the sun visor ................................................. 14
When installing the microphone
on the steering column..................................... 15
Adjusting the microphone angle .......................... 15
Installing the steering remote control ......... 15
Installing the unit on a left-hand drive car........... 16
Note
• When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
detect the operation of the ignition key. Otherwise,
battery drain may result.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
ACC position No ACC position
• Use this unit in other than the following
conditions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or
malfunction, be sure to follow the directions
below.
— Disconnect the negative terminal of the
battery before installation.
— Secure the wiring with cable clamps or
adhesive tape. To protect the wiring, wrap
adhesive tape around them where they lie
against metal parts.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
—Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
—Use a fuse of the rating prescribed.
—Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker’s
negative cables.

3
English
<0G020184B> <3>
Connecting the units
• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
external power amp’s system remote control or
the vehicle’s auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is equipped
with a glass antenna, connect it to the antenna
booster power supply terminal.
•Never connect blue/white cable to external power
amp’s power terminal. Also, never connect
it to the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.
•IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
• Black cable is ground. This cable and other
product’s ground cable (especially, high-current
products such as power amp) must be wired
separately. Otherwise, fire or malfunction may
result if they are accidentally detached.

4
<0G020184B> <4>
Connecting the power cord
Connecting the units Connecting the units
Subwoofer output
This product
Antenna jack
Front output
Rear output
IP-BUS input (Blue)
Wired remote input
Hard-wired remote control
adaptor can be connected
(sold separately).
IP-BUS cable
Multi-CD player
(sold separately)
Microphone input
USB cable
Use supplied USB cable or separately
sold USB cable (CD-U150E).
AUX jack (3.5 φ)
Use a stereo mini plug cable
to connect with auxiliary
device.
Microphone
iPod to USB connection cable
Use supplied iPod to USB connection
cable.








Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by
ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free metal location.
Left Right
Blue/white
Connect to system control terminal of the power
amp or auto-antenna relay control terminal (max.
300 mA 12 V DC).
With a 2 speaker system, do not
connect anything to the speaker leads
that are not connected to speakers.
Front speaker Front speaker
Rear speaker Rear speaker
White Gray
Gray/blackWhite/black
Green Violet
Green/black Violet/black
1.5 m (4 ft. 9 in.)
20 cm
(7-7/8 in.)
15 cm
(5-7/8 in.)
Fuse (10 A)
Fuse resister
4 m (13 ft. 1 in.)
When connecting speakers without using the internal
amplifier, we recommend that this unit’s internal amp is
turned off. For more details, refer to operation manual.
0.5 m (1 ft. 8 in.)
Orange/white
Connect to lighting switch terminal.
Fuse resister
USB1/USB2 input jack

5
English
<0G020184B> <5>
Connecting the power cord
Connecting the units Connecting the units
Subwoofer output
This product
Antenna jack
Front output
Rear output
IP-BUS input (Blue)
Wired remote input
Hard-wired remote control
adaptor can be connected
(sold separately).
IP-BUS cable
Multi-CD player
(sold separately)
Microphone input
USB cable
Use supplied USB cable or separately
sold USB cable (CD-U150E).
AUX jack (3.5 φ)
Use a stereo mini plug cable
to connect with auxiliary
device.
Microphone
iPod to USB connection cable
Use supplied iPod to USB connection
cable.








Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by
ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free metal location.
Left Right
Blue/white
Connect to system control terminal of the power
amp or auto-antenna relay control terminal (max.
300 mA 12 V DC).
With a 2 speaker system, do not
connect anything to the speaker leads
that are not connected to speakers.
Front speaker Front speaker
Rear speaker Rear speaker
White Gray
Gray/blackWhite/black
Green Violet
Green/black Violet/black
1.5 m (4 ft. 9 in.)
20 cm
(7-7/8 in.)
15 cm
(5-7/8 in.)
Fuse (10 A)
Fuse resister
4 m (13 ft. 1 in.)
When connecting speakers without using the internal
amplifier, we recommend that this unit’s internal amp is
turned off. For more details, refer to operation manual.
0.5 m (1 ft. 8 in.)
Orange/white
Connect to lighting switch terminal.
Fuse resister
USB1/USB2 input jack

6
<0G020184B> <6>
When using a subwoofer without using the optional amplifier
Connecting the units Connecting the units
Subwoofer output
This product
Antenna jack
Front output
Rear output
IP-BUS input (Blue)
Wired remote input
Hard-wired remote control
adaptor can be connected
(sold separately).
IP-BUS cable
Multi-CD player
(sold separately)
Microphone input
AUX jack (3.5 φ)
Use a stereo mini plug cable
to connect with auxiliary
device.
Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by
ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free metal location.
Blue/white
Connect to system control terminal of the power
amp or auto-antenna relay control terminal (max.
300 mA 12 V DC).
20 cm
(7-7/8 in.)
15 cm
(5-7/8 in.)
Fuse (10 A)
Orange/white
Connect to lighting switch terminal.
Fuse resister
USB1/USB2 input jack


Green Violet
Green/black Violet/black
When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black
leads of this unit. Do not connect anything with Green and Green/black leads.
Subwoofer
(4 Ω)2
Not used.






Left Right
Front speaker Front speaker
White Gray
Gray/blackWhite/black
Green Violet
Green/black Violet/black
Subwoofer (4 Ω) Subwoofer (4 Ω)


USB cable
Use supplied USB cable or separately
sold USB cable (CD-U150E).
iPod to USB connection cable
Use supplied iPod to USB connection
cable.
1.5 m (4 ft. 9 in.)
0.5 m (1 ft. 8 in.)
Fuse resister
Microphone 4 m (13 ft. 1 in.)

7
English
<0G020184B> <7>
When using a subwoofer without using the optional amplifier
Connecting the units Connecting the units
Subwoofer output
This product
Antenna jack
Front output
Rear output
IP-BUS input (Blue)
Wired remote input
Hard-wired remote control
adaptor can be connected
(sold separately).
IP-BUS cable
Multi-CD player
(sold separately)
Microphone input
AUX jack (3.5 φ)
Use a stereo mini plug cable
to connect with auxiliary
device.
Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by
ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free metal location.
Blue/white
Connect to system control terminal of the power
amp or auto-antenna relay control terminal (max.
300 mA 12 V DC).
20 cm
(7-7/8 in.)
15 cm
(5-7/8 in.)
Fuse (10 A)
Orange/white
Connect to lighting switch terminal.
Fuse resister
USB1/USB2 input jack


Green Violet
Green/black Violet/black
When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black
leads of this unit. Do not connect anything with Green and Green/black leads.
Subwoofer
(4 Ω)2
Not used.






Left Right
Front speaker Front speaker
White Gray
Gray/blackWhite/black
Green Violet
Green/black Violet/black
Subwoofer (4 Ω) Subwoofer (4 Ω)


USB cable
Use supplied USB cable or separately
sold USB cable (CD-U150E).
iPod to USB connection cable
Use supplied iPod to USB connection
cable.
1.5 m (4 ft. 9 in.)
0.5 m (1 ft. 8 in.)
Fuse resister
Microphone 4 m (13 ft. 1 in.)

8
<0G020184B> <8>
When connecting to separately sold power amp
Subwoofer output
This product
Antenna jack
Front output
Rear output
IP-BUS input (Blue)
Wired remote input
Hard-wired remote control
adaptor can be connected
(sold separately).
IP-BUS cable
Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
Multi-CD player
(sold separately)
AUX jack (3.5 φ)
Use a stereo mini plug cable
to connect with auxiliary
device.
Perform these connections when using
the optional amplifier.
Note
Change the initial setting of this unit (refer to the
operation manual). The subwoofer output of this unit is
monaural.
To subwoofer output
To front output
To rear output








Power amp
(sold separately)
RightLeft
Power amp
(sold separately)
Power amp
(sold separately)
Connect with RCA cables
(sold separately)
System remote control
Front speaker Front speaker
Rear speaker Rear speaker
Subwoofer Subwoofer
Connecting the units Connecting the units

9
English
<0G020184B> <9>
When connecting to separately sold power amp
Subwoofer output
This product
Antenna jack
Front output
Rear output
IP-BUS input (Blue)
Wired remote input
Hard-wired remote control
adaptor can be connected
(sold separately).
IP-BUS cable
Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
Multi-CD player
(sold separately)
AUX jack (3.5 φ)
Use a stereo mini plug cable
to connect with auxiliary
device.
Perform these connections when using
the optional amplifier.
Note
Change the initial setting of this unit (refer to the
operation manual). The subwoofer output of this unit is
monaural.
To subwoofer output
To front output
To rear output








Power amp
(sold separately)
RightLeft
Power amp
(sold separately)
Power amp
(sold separately)
Connect with RCA cables
(sold separately)
System remote control
Front speaker Front speaker
Rear speaker Rear speaker
Subwoofer Subwoofer
Connecting the units Connecting the units

10
<0G020184B> <10>
When connecting speakers without using the internal amplifier
• If using this system, we recommend that this unit’s internal amp is turned off.
For more details, refer to operation manual.
Connecting the units Connecting the units
Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by
ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free metal location.
Blue/white
Connect to system control terminal of the power
amp or auto-antenna relay control terminal (max.
300 mA 12 V DC).
Fuse (10 A)
Fuse resister
When connecting speakers without using the internal
amplifier, we recommend that this unit’s internal amp is
turned off. For more details, refer to operation manual.
Orange/white
Connect to lighting switch terminal.
Fuse resister




Power amp
(sold separately)
Connect with RCA cables
(sold separately)
System remote control
Power amp
(sold separately)


Front speaker


Power amp
(sold separately)
To front output
To rear output
Front speaker
Rear speaker
Rear speaker
Subwoofer Subwoofer
Subwoofer output
This product
Antenna jack
Front output
Rear output
Not used.
White Gray
Gray/blackWhite/black
Green Violet
Violet/blackGreen/black
To subwoofer
output

11
English
<0G020184B> <11>
When connecting speakers without using the internal amplifier
• If using this system, we recommend that this unit’s internal amp is turned off.
For more details, refer to operation manual.
Connecting the units Connecting the units
Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by
ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free metal location.
Blue/white
Connect to system control terminal of the power
amp or auto-antenna relay control terminal (max.
300 mA 12 V DC).
Fuse (10 A)
Fuse resister
When connecting speakers without using the internal
amplifier, we recommend that this unit’s internal amp is
turned off. For more details, refer to operation manual.
Orange/white
Connect to lighting switch terminal.
Fuse resister




Power amp
(sold separately)
Connect with RCA cables
(sold separately)
System remote control
Power amp
(sold separately)


Front speaker


Power amp
(sold separately)
To front output
To rear output
Front speaker
Rear speaker
Rear speaker
Subwoofer Subwoofer
Subwoofer output
This product
Antenna jack
Front output
Rear output
Not used.
White Gray
Gray/blackWhite/black
Green Violet
Violet/blackGreen/black
To subwoofer
output

12
<0G020184B> <12>
Installation
Note
• Check all connections and systems before final
installation.
• Do not use unauthorized parts. The use of
unauthorized parts may cause malfunctions.
•Consult with your dealer if installation requires
drilling of holes or other modifications of the
vehicle.
•Do not install this unit where:
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result
of a sudden stop.
•The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.
•Optimum performance is obtained when the unit is
installed at an angle of less than 60°.
• When installing, to ensure proper heat dispersal
when using this unit, make sure you leave ample
space behind the rear panel and wrap any loose
cables so they are not blocking the vents.
10cm (3-7/8 in.)
Leave ample space Dashboard
10cm (3-7/8 in.)
• The cords must not cover up the area shown in the
figure. This is necessary to allow the amplifiers to
radiate freely.
DIN Front/Rear-mount
This unit can be properly installed either from
“Front”(conventional DIN Front-mount) or
“Rear”(DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit
chassis). For details, refer to the following
installation methods.
Removing or attaching
the trim ring
1. Extend top and bottom of the trim ring
outwards to remove the trim ring.
•When reattaching the trim ring, push the trim
ring onto the unit until it clicks. (If the trim ring
is attached upside down, the trim ring will not
fit properly.)
•It becomes easy to remove the trim ring if the
front panel is released.
Do not cover this area.
Trim ring

13
English
<0G020184B> <13>
Installation
DIN Front-mount
Installation with metal strap and
screws
1. Insert the mounting sleeve into the
dashboard.
• When installing in a shallow space, use a
supplied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.
2. Secure the mounting sleeve by using
a screwdriver to bend the metal tabs
(90°) into place.
3. Install the unit.
Use commercially available parts when
installing.
• Make sure that the unit is installed securely in
place. Unstable installation may cause this unit to
malfunction, such as sound skip.
Removing the Unit
1. Insert the supplied extraction keys
into both sides of the unit until they
click into place.
2. Pull the unit out of the dashboard.
DIN Rear-mount
1. Determine the appropriate position
where the holes on the bracket and
the side of the unit match.
2. Tighten two screws on each side.
• Use either truss screws (5 mm × 8 mm)
or flush surface screws (5 mm × 9 mm),
depending on the shape of screw holes in the
bracket.
Screw
Factory radio mounting bracket Dashboard or
Console
Metal strap
Screw
Screw
(M4 ×8)
Filrewall or metal support
Nut

14
<0G020184B> <14>
Installation
Fastening the front panel
If you do not plan to detach the front panel,
the front panel can be fastened with supplied
screws and holders.
1. Attach the holders to both sides of the
front panel.
2. Replace the front panel to the unit.
3. Flip the holders into upright
positions.
4. Fix the front panel to the unit using
screws.
Installing the microphone
Install the microphone in a position and
orientation that will enable it to pick up the
voice of the person operating the system.
CAUTION
• It is extremely dangerous to allow the microphone
lead to become wound around the steering
column or gearstick. Be sure to install the unit in
such a way that it will not obstruct driving.
When installing the microphone
on the sun visor
1. Install the microphone on the
microphone clip.
2. Install the microphone clip on the sun
visor.
• With the sun visor up, install the microphone
clip. (Lowering the sun visor reduces the voice
recognition rate.)
• Use separately sold clamps to secure the lead
where necessary inside the vehicle.
Microphone
Microphone clip
Microphone clip
Clamp
Holder
Screw

15
English
<0G020184B> <15>
Installation
When installing the microphone
on the steering column
1. Install the microphone on the
microphone clip.
• Microphone can be installed without using
microphone clip. In this case, detach the
microphone base from the microphone clip. To
detach the microphone base from microphone
clip, slide the microphone base.
2. Install the microphone clip on the
steering column.
• Use separately sold clamps to secure the lead
where necessary inside the vehicle.
Adjusting the microphone angle
The microphone angle can be adjusted.
Installing the steering remote
control
WARNING
• Avoid installing this unit in such a location where
the operation of safety devices such as airbags
is prevented by this unit. Otherwise, there is a
danger of a fatal accident.
•Avoid installing this unit in such a location where
the operation of the steering wheel and the
gearshift lever may be prevented. Otherwise, it
may result in a traffic accident.
CAUTION
• Installation of this unit requires specialized skills
and experience. Installation of this unit should be
entrusted to a dealer from whom you purchased
this unit.
•Install this unit using only the parts supplied with
this unit. If other parts are used, this unit may be
damaged or could dismount itself, which leads to
an accident or trouble.
• Install this unit as required by this manual. Failure
to do so may cause an accident.
• Do not install this unit near the doors where
rainwater is likely to be spilled on the unit.
Incursion of water into the unit may cause smoke
or fire.
WARNING
• Fix this unit securely to the steering wheel with
the belt attached to the unit. If this unit is loose,
it disturbs driving stability, which may result in a
traffic accident.
•Do not attach this unit to the outer circumference
of the steering wheel. Otherwise, it disturbs
driving stability, causing a traffic accident. Always
attach this unit to the inner circumference of the
steering wheel as shown.
Microphone
Microphone clip
Fit the microphone
lead into the groove
Double-sided tape
Install the microphone
clip on the rear side of the
steering column.
Clamp
Microphone base

16
<0G020184B> <16>
Installation
Note
• Do not install this unit in such a place as may
obstruct the driver’s view.
• Since interior layout differs depending on the type
of vehicle, the ideal installation location for the
unit also differs. When installing the unit, select
a location that assures optimum transmission of
signals from the unit to the car stereo.
Installing the unit on a left-hand
drive car
Note
• When the unit is installed on a right-hand-drive
car, the horizontal positions are inverted.
1. Hook the belt on to the holder.
2. Fix the holder to the inside edge of
the steering wheel so that the holder
is facing the driver.
• 12 Wrap the belt around the outside edge of the
steering wheel, passing the end through the slot
in the holder.
3Pull on the belt to tighten it then secure it using
the other two hooks on the holder.
3. 4Cut off the extra portion of the belt.
• 5If some of the belt still protrudes, fold it back
into the slot so that it does not interfere with
driving.
4. Fasten the other belt in the same way.
5. Install the remote control unit in the
holder.
• When removing the remote control unit from
the holder, move the corrugated release section
toward the steering wheel and slide the remote
control unit toward you.

17
English
<0G020184B> <17>

<0G020184B> <18>
Table des matières Connexions des appareils
Connexions des appareils ................... 2
Branchement du cordon d’alimentation ....... 4
Lors de l’utilisation d’un caisson de
grave sans utiliser l’amplificateur
en option ..................................................... 6
Raccordements à un amplificateur de
puissance vendu séparément................... 8
Quand vous raccordez les enceintes
sans utiliser l’amplificateur interne........ 10
Installation ........................................... 12
Montage avant/arrière DIN ........................... 12
Retrait ou fixation de la garniture ......................... 12
Montage frontal DIN .............................................. 13
Montage arrière DIN .............................................. 13
Fixation du panneau avant............................ 14
Installation du microphone........................... 14
Installation du microphone sur le
pare-soleil............................................................14
Installation du microphone sur la
colonne de direction ..........................................15
Ajustement de l’angle du microphone..................15
Installation du boîtier de télécommande
sur le volant .............................................. 15
Installation de l’unité sur une voiture
à direction à gauche ......................................... 16
Remarque
• Si cet appareil est installé dans un véhicule sans
position ACC (accessoire) sur le commutateur
d’allumage, le câble rouge doit être connecté
à une borne qui peut détecter la position du
commutateur d’allumage. Sinon, la batterie risque
de se décharger.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
Position ACC Pas de position ACC
• Utiliser cet appareil dans d’autres conditions
que les conditions suivantes peut entraîner un
incendie ou un mauvais fonctionnement.
—Véhicule avec une batterie de 12 volts et une
mise à la masse négative.
— Enceintes de 50 W (valeur de sortie) et de 4
ohms à 8 ohms (valeur d’impédance).
• Pour éviter tout court-circuit, surchauffe ou
mauvais fonctionnement, assurez-vous de suivre
les instructions ci-dessous.
— Déconnectez la borne négative de la batterie
avant l’installation.
— Fixez solidement les câbles avec des
serrecâbles ou du ruban adhésif. Pour
protéger le câblage, entourez-le de ruban
adhésif à l’endroit où il est en contact avec des
pièces métalliques.
—Tenez tous les câbles à l’écart des parties
mobiles, telles que le levier de vitesse et les
rails des sièges.
— Tenez tous les câbles à l’écart des endroits
chauds, tels que les sorties du chauffage.
— Ne faites pas passer le câble jaune par un
trou dans le compartiment du moteur pour le
connecter à la batterie.
— Recouvrez tous les câbles non connectés avec
du ruban isolant.
— Ne raccourcissez aucun câble.
—Ne coupez jamais l’isolant du câble
d’alimentation de cet appareil afin partager
l’alimentation avec un autre appareil. La
capacité électrique du câble est limitée.
—Utilisez un fusible de la valeur donnée.
—Ne connectez jamais le câble négatif des
enceintes directement à la masse.
— N’attachez jamais ensemble plusieurs câbles
négatifs de plusieurs enceintes.
2

<0G020184B> <19>
Français
Connexions des appareils
• Le signal de commande est sorti par le câble
bleu/blanc quand cet appareil est sous
tension. Connectez-le à la télécommande
d’un système d’amplification extérieur ou à la
prise de commande du contrôle de relais de
l’antenne automatique (max. 300 mA, 12 V CC).
Si la véhicule est équipée d’une antenne de
vitre, connectez-la à la prise d’alimentation de
l’amplificateur d’antenne.
•Ne connectez jamais le câble bleu/blanc à la prise
d’alimentation d’un amplificateur extérieur. Et
ne le connectez pas à la prise d’alimentation de
l’antenne automatique. Sinon, la batterie risque
de se décharger ou un mauvais fonctionnement
peut se produire.
•Les connecteurs IP-BUS sont codés par couleur.
Assurez-vous de connecter les connecteurs de
même couleur.
• Le câble noir est pour la masse. Ce câble et
les câbles de masse des autres produits (en
particulier les appareils à haute intensité tels
que les amplificateurs) doivent être câblés
séparément. Sinon, ils peuvent entraîner un
incendie ou un mauvais fonctionnement s’ils se
détachent.
3

<0G020184B> <20>
Branchement du cordon d’alimentation
Connexions des appareils Connexions des appareils
Sortie de caisson
de grave
Cet appareil
Prise d’antenne
Sortie avant
Sortie arrière
Entrée IP-BUS (bleue)
Entrée de télécommande à fil
Vous pouvez connecter un
adaptateur pour
télécommande à fil (vendu
séparément) à cette prise.
Câble IP-BUS
Entrée microphone
Câble USB
Utiliser le câble USB fourni ou le câble
USB vendu séparément (CD-U150E).
Prise AUX (3,5 φ)
Utilisez un câble à mini fiche
stéréo pour connecter un
appareil auxiliaire.
Microphone
Câble de connexion iPod à USB
Utiliser le câble de connexion iPod à
USB fourni.








Jaune
Raccordez ce fil à la borne d’alimentation
constante 12 V.
Rouge
Raccordez ce fil à la prise commandée par la
clé de contact (12 V CC).
Noir (mise à la masse sur le châssis)
Raccordez ce fil à une section métallique du
châssis, propre et sans peinture.
Gauche Droit
Bleu/blanc
Raccordez ce fil à la prise de commande du
système de l’amplificateur de puissance ou à la
prise de commande de relais de l’antenne
motorisée (max. 300 mA 12 V CC).
Avec un système à deux enceintes, ne
raccordez rien aux fils d’enceinte qui
ne sont pas connectés aux enceintes.
Enceinte
avant
Enceinte
avant
Enceinte
arrière
Enceinte
arrière
Blanc Gris
Gris/noirBlanc/noir
Vert Violet
Vert/noir Violet/noir
1,5 m
20 cm
15 cm
Fusible (10 A)
Résistance fusible
4 m
Lors de la connexion des enceintes sans utiliser
l'amplificateur interne, nous recommandons de mettre
hors service l’amplificateur interne de cet appareil. Pour
plus de détails, reportez-vous au manuel d’utilisation.
0,5 m
Orange/blanc
Connectez à la prise du commutateur d’éclairage.
Résistance fusible
Prise d’entrée USB1/USB2
Lecteur de CD à
chargeur (vendu
séparément)
4