Pioneer SUPER TUNER III D FH-P4200MP User manual

Operation Manual
Multi-CD control DSP High power CD/MP3/WMA/
Cassette player with FM/AM tuner
FH-P4200MP
English \Español

Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how to operate
your model properly. After you have finished reading the instructions, keep this man-
ual in a safe place for future reference.
Before You Start
About this unit 5
About this manual 5
Features 5
About WMA 6
About AAC 6
Use and care of the remote control 6
Installing the battery 6
Using the remote control 7
About the demo mode 7
Resetting the microprocessor 7
Whats What
ead unit 8
Remote control 9
Power ON/OFF
Turning the unit on 10
Selecting a source 10
Turning the unit off 10
Tuner
Listening to the radio 11
Introduction of advanced tuner
operation 12
Storing and recalling broadcast
frequencies 12
Tuning in strong signals 12
Storing the strongest broadcast
frequencies 13
Cassette P ayer
Playing a tape 14
Introduction of advanced cassette player
operation 15
Repeating play 15
Skipping blank tape sections 15
Using Dolby noise reduction 15
Bui t-in CD P ayer
Playing a CD 17
Introduction of advanced built-in CD player
operation 18
Repeating play 18
Playing tracks in a random order 18
Scanning tracks of a CD 18
Pausing CD playback 19
Using compression and BMX 19
Selecting the search method 19
Searching every 10 tracks in the current
disc 20
Using disc title functions 20
Entering disc titles 20
Displaying disc titles 21
Using CD TEXT functions 21
Displaying titles on CD TEXT
discs 21
Scrolling titles in the display 21
MP3/WMA/AAC/WAV P ayer
Playing MP3/WMA/AAC/WAV 22
Introduction of advanced built-in CD player
(MP3/WMA/AAC/WAV) operation 23
Repeating play 23
Playing tracks in a random order 24
Scanning folders and tracks 24
Pausing MP3/WMA/AAC/WAV playback 24
Using compression and BMX 25
Selecting the search method 25
Searching every 10 tracks in the current
folder 25
Displaying text information on MP3/WMA/
AAC/WAV disc 26
When playing back an MP3/WMA/
AAC disc 26
When playing back a WAV disc 26
Scrolling text information in the display 26
Contents
En
2

Mu ti-CD P ayer
Playing a CD 27
50-disc multi-CD player 27
Introduction of advanced multi-CD player
operation 28
Repeating play 28
Playing tracks in a random order 28
Scanning CDs and tracks 29
Pausing CD playback 29
Using ITS playlists 29
Creating a playlist with ITS
programming 29
Playback from your ITS playlist 30
Erasing a track from your ITS
playlist 30
Erasing a CD from your ITS
playlist 30
Using disc title functions 31
Entering disc titles 31
Displaying disc titles 32
Selecting discs from the disc title
list 32
Using CD TEXT functions 32
Displaying titles on CD TEXT
discs 32
Scrolling titles in the display 32
Using compression and bass emphasis 33
Audio Adjustments
Introduction of audio adjustments 34
Using balance adjustment 34
Adjusting loudness 35
Using nonfading output 35
Adjusting nonfading output level 35
Using subwoofer output 35
Adjusting subwoofer (low pass filter)
settings 36
Adjusting low pass filter attenuation
slope 36
Using the high pass filter 36
Adjusting high pass filter attenuation
slope 37
Adjusting source levels 37
Digita Signa Processor
Using the digital signal processor 38
Using the graphic equalizer 38
Recalling equalizer curves 38
Adjusting equalizer curves 39
Adjusting 9-band graphic
equalizer 39
Using the position selector 40
Using sound field control and BBE
sound 40
Recalling sound field programs 40
Adjusting BBE sound level 41
Initia Settings
Adjusting initial settings 42
Setting the clock 42
Setting the FM tuning step 42
Setting the AM tuning step 43
Switching the auxiliary setting 43
Switching the dimmer setting 43
Adjusting display contrast 43
Switching the RCA output setting 43
Selecting the digital attenuator 44
Switching the telephone muting/
attenuation 44
Switching the Ever Scroll 44
Other Functions
Turning the clock display on or off 45
Using different entertainment displays 45
Using the AUX source 45
Selecting AUX as the source 45
Setting the AUX title 45
En 3
English
Contents

Additiona Information
Understanding built-in CD player error
messages 47
Cassette tapes 47
Cleaning the playback head 47
Music search and repeat functions during
tape playback 47
CD player and care 48
CD-R/CD-RW discs 48
MP3, WMA, AAC and WAV files 49
MP3 additional information 50
WMA additional information 50
AAC additional information 50
WAV additional information 50
About folders and MP3/WMA/AAC/WAV
files 51
Terms 52
Specifications 54
Contents
En
4

About this unit
CAUTION
!Do not allow this unit to come into contact
with liquids. Electrical shock could result.
Also, this unit damage, smoke, and overheat
could result from contact with liquids.
!Keep this manual handy as a reference for op-
erating procedures and precautions.
!Always keep the volume low enough so that
you can hear sounds from outside the vehicle.
!Protect this unit from moisture.
!If the battery is disconnected or discharged,
the preset memory will be erased and must be
reprogrammed.
!If this unit does not operate properly, contact
your dealer or nearest authorized Pioneer Ser-
vice Station.
About this manual
This unit features a number of sophisticated
functions ensuring superior reception and op-
eration. All the functions have been designed
for the easiest possible use, but many are not
self-explanatory. This operation manual will
help you benefit fully from this units potential
and to maximize your listening enjoyment.
We recommend that you familiarize yourself
with the functions and their operation by read-
ing through the manual before you begin
using this unit. It is especially important that
you read and observe WARNINGs and CAU-
TIONs in this manual.
Features
CD playback
Music CD/CD-R/CD-RW playback is possible.
MP3 file playback
You can play back MP3 files recorded on CD-
ROM/CD-R/CD-RW (ISO9660 Level 1/Level 2
standard recordings).
!Supply of this product only conveys a li-
cense for private, non-commercial use and
does not convey a license nor imply any
right to use this product in any commercial
(i.e. revenue-generating) real time broad-
casting (terrestrial, satellite, cable and/or
any other media), broadcasting/streaming
via internet, intranets and/or other net-
works or in other electronic content distri-
bution systems, such as pay-audio or
audio-on-demand applications. An inde-
pendent license for such use is required.
For details, please visit
http://www.mp3licensing.com.
WMA file playback
You can play back WMA files recorded on CD-
ROM/CD-R/CD-RW (ISO9660 Level 1/Level 2
standard recordings).
AAC file playback
You can play back AAC files recorded on CD-
ROM/CD-R/CD-RW (ISO9660 Level 1/Level 2
standard recordings).
WAV file playback
You can play back WAV files recorded on CD-
ROM/CD-R/CD-RW (Linear PCM (LPCM)/MS
ADPCM recordings).
Before You Start
En 5
English
Section
01

About WMA
The Windows Media"logo printed on the box
indicates that this unit can play back WMA
data.
WMA is short for Windows Media Audio and
refers to an audio compression technology
that is developed by Microsoft Corporation.
WMA data can be encoded by using Windows
Media Player version 7 or later.
Microsoft, Windows Media, and the Windows
logo are trademarks, or registered trademarks
of Microsoft Corporation in the United States
and/or other countries.
Notes
!With some applications used to encode WMA
files, this unit may not operate correctly.
!Depending on the version of Windows Media
Player used to encode WMA files, album
names and other text information may not be
correctly displayed.
About AAC
AAC is short for Advanced Audio Coding and
refers to an audio compression technology
standard used with MPEG 2 and MPEG 4.
Several applications can be used to encode
AAC files, but file formats and extensions dif-
fer depending on the application, which is
used to encode.
This unit plays back AAC files encoded by
iTunes®version 4.1.1.54.
iTunes®is a trademark of Apple Computer,
Inc., registered in the U.S. and other
countries.
Use an care of the remote
control
Installing the battery
Slide the tray out on the back of the remote
control and insert the battery with the plus (+)
and minus () poles pointing in the proper di-
rection.
WARNING
Keep the battery out of the reach of children.
Should the battery be swallowed, immediately
consult a doctor.
CAUTION
!Use only one CR2025 (3 V) lithium battery.
!Remove the battery if the remote control is not
used for a month or longer.
!Do not recharge, disassemble, heat or dispose
of the battery in fire.
!Do not handle the battery with metallic tools.
!Do not store the battery with metallic materi-
als.
!In the event of battery leakage, wipe the re-
mote control completely clean and install a
new battery.
!When disposing of used batteries, please
comply with governmental regulations or en-
vironmental public institutionsrules that
apply in your country/area.
Before You Start
En
6
Section
01

Using the remote control
Point the remote control in the direction of the
front panel to operate.
Important
!Do not store the remote control in high tem-
peratures or direct sunlight.
!The remote control may not function properly
in direct sunlight.
!Do not let the remote control fall onto the
floor, where it may become jammed under the
brake or accelerator pedal.
About the emo mo e
The demonstration automatically starts when
power to this unit is turned off while the igni-
tion switch is set to ACC or ON. Pressing 6
numbered button during demonstration can-
cels the demonstration. Pressing 6numbered
button again to start the demonstration. Re-
member that if the demonstration continues
operating when the car engine is turned off, it
may drain battery power.
Important
The red lead (ACC) of this unit should be con-
nected to a terminal coupled with ignition switch
on/off operations. If this is not done, the vehicle
battery may be drained.
Resetting the microprocessor
The microprocessor must be reset under the
following conditions:
!Prior to using this unit for the first time
after installation
!If the unit fails to operate properly
!When strange or incorrect messages ap-
pear on the display
%Press RESET on the head unit with a
pen tip or other pointed instrument.
RESET button
Before You Start
En 7
English
Section
01

Hea unit
1TAPE EJECT button
Press to eject a tape from your cassette
player.
2AUDIO button
Press to select various sound quality con-
trols.
3CLOCK button
Press to change to the clock display.
4UNCTION button
Press to select functions.
5DISPLAY button
Press to select different displays.
6ENTERTAINMENT button
Press to change to the entertainment dis-
play.
7DSP button
Press to select sound field functions.
816 buttons
Press for preset tuning and disc number
search when using a multi-CD player.
9SOURCE button
This unit is turned on by selecting a source.
Press to cycle through all the available
sources.
aVOLUME
Rotate it to increase or decrease the vo-
lume.
bBAND button
Press to select among three FM bands and
one AM band and to cancel the control
mode of functions.
Press to change the direction of the tape
transport and return to playback after fast
forward or rewind.
ca/b/c/dbuttons
Press to do manual seek tuning, fast for-
ward, reverse and track search controls.
Also used for controlling functions.
1
2
3
4
567 8 9a
b
c
d
e
Whats What
En
8
Section
02

dCD EJECT button
Press to eject a CD from your built-in CD
player.
eRESET button
Press to reset the microprocessor.
Remote control
Operation is the same as when using the but-
tons on the head unit.
fVOLUME button
Press to increase or decrease the volume.
gCD button
Press to select the built-in or multi-CD
player as the source.
hCASSETTE button
Press to select the cassette player as the
source.
iTUNER button
Press to select the tuner as the source.
jATT button
Press to quickly lower the volume level, by
about 90%. Press once more to return to the
original volume level.
j
c
2
g
4
f
h
i
b
Whats What
En 9
English
Section
02

Turning the unit on
%Press SOURCE on the head unit, or
press TUNER, CASSETTE or CD on the re-
mote, to turn the unit on.
When you select a source the unit is turned
on.
Selecting a source
You can select a source you want to listen to.
To switch to the built-in CD player, load a disc
in this unit (refer to page 17). To switch to the
cassette player, load a cassette tape in this
unit (refer to page 14).
%When using the head unit, press
SOURCE to select a source.
Press SOURCE repeatedly to switch between
the following sources:
TunerTe evisionBui t-in CD p ayer
Mu ti-CD p ayerCassette p ayerExter-
na unit 1Externa unit 2AUX
%When using the remote control, press
TUNER, CASSETTE or CD to select a source.
Press each button repeatedly to switch be-
tween the following sources:
TUNER:TunerTe evisionSources off
CASSETTE:Cassette p ayerAUX
Sources off
CD:Bui t-in CD p ayerMu ti-CD p ayer
Sources off
Notes
!In the following cases, the sound source will
not change:
When there is no unit corresponding to the
selected source connected to this unit.
When there is no disc in the unit.
When there is no cassette in this unit.
When there is no magazine in the multi-
CD player.
When the AUX (auxiliary input) is set to off
(refer to page 43).
!External unit refers to a Pioneer product (such
as one available in the future) that, although
incompatible as a source, enables control of
basic functions by this unit. Two external units
can be controlled by this unit. When two exter-
nal units are connected, the allocation of
them to external unit 1 or external unit 2 is
automatically set by this unit.
!When this units blue lead is connected to the
cars auto-antenna relay control terminal, the
cars antenna extends when this units se-
lected source is the tuner. To retract the anten-
na, switch to a source other than the tuner.
Turning the unit off
%Press SOURCE and hold until the unit
turns off.
When using the remote control, press TUNER,
CASSETTE or CD repeatedly.
Power ON/OFF
En
10
Section
03

Listening to the ra io
123
These are the basic steps necessary to operate
the radio. More advanced tuner operation is
explained starting on the next page.
Important
If you are using this unit in North, Central or
South America, reset the AM tuning step (see
Setting the AM tuning step on page 43).
1Band indicator
Shows which band the radio is tuned to, AM
or FM.
2requency indicator
Shows to which frequency the tuner is
tuned.
3Stereo (5) indicator
Shows that the frequency selected is being
broadcast in stereo.
1 Press SOURCE to select the tuner.
Press SOURCE until you see Tuner displayed.
2 Use VOLUME to adjust the sound level.
Rotate it to increase or decrease the volume.
3 Press BAND to select a band.
Press BAND until the desired band is dis-
played, 1,2,3 for FM or AM.
4 To perform manual tuning, briefly press
cor d.
The frequencies move up or down step by
step.
5 To perform seek tuning, press and hold
cor dfor about one second and release.
The tuner will scan the frequencies until a
broadcast strong enough for good reception is
found.
#You can cancel seek tuning by briefly pressing
either cor d.
#If you press and hold cor dyou can skip sta-
tions. Seek tuning starts as soon as you release
the button.
Tuner
En 11
English
Section
04

Intro uction of a vance
tuner operation
123
1unction display
Shows the function status.
2LOC indicator
Shows when local seek tuning is on.
3Preset number indicator
Shows which preset has been selected.
%Press UNCTION to display the function
names.
Press UNCTION repeatedly to switch be-
tween the following functions:
BSM (best stations memory)Local (local
seek tuning)
#To return to the frequency display, press
BAND.
Note
If you do not operate the function within about 30
seconds, the display is automatically returned to
the frequency display.
Storing an recalling
broa cast frequencies
If you press any of the preset tuning buttons
16you can easily store up to six broadcast
frequencies for later recall with the touch of a
button.
%When you find a frequency that you
want to store in memory press one of pre-
set tuning buttons 16 and hold until the
preset number stops flashing.
The number you have pressed will flash in the
preset number indicator and then remain lit.
The selected radio station frequency has been
stored in memory.
The next time you press the same preset tun-
ing button the radio station frequency is re-
called from memory.
Notes
!Up to 18 FM stations, six for each of the three
FM bands, and six AM stations can be stored
in memory.
!You can also use aand bto recall radio sta-
tion frequencies assigned to preset tuning
buttons 16.
Tuning in strong signals
Local seek tuning lets you tune in only those
radio stations with sufficiently strong signals
for good reception.
1 Press UNCTION to select Local.
Press UNCTION until Local appears in the
display.
2 Press ato turn local seek tuning on.
Local seek sensitivity (e.g., Local: 2) appears
in the display.
3 Press cor dto set the sensitivity.
There are four levels of sensitivity for FM and
two levels for AM:
FM: Local: 1Local: 2Local: 3Local: 4
AM: Local: 1Local: 2
The Local: 4 setting allows reception of only
the strongest stations, while lower settings let
you receive progressively weaker stations.
Tuner
En
12
Section
04

4 When you want to return to normal
seek tuning, press bto turn local seek tun-
ing off.
Local:O appears in the display.
Storing the strongest
broa cast frequencies
BSM (best stations memory) lets you automa-
tically store the six strongest broadcast fre-
quencies under preset tuning buttons 16and
once stored there you can tune in to those fre-
quencies with the touch of a button.
1 Press UNCTION to select BSM.
Press UNCTION until BSM appears in the
display.
2 Press ato turn BSM on.
BSM begins to flash. While BSM is flashing
the six strongest broadcast frequencies will be
stored under preset tuning buttons 16in the
order of their signal strength. When finished,
BSM stops flashing.
#To cancel the storage process, press b.
Tuner
En 13
English
Section
04

Playing a tape
12
These are the basic steps necessary to play a
tape with your cassette player. More advanced
cassette player operation is explained starting
on the next page.
1Tape direction indicator
Shows the direction of the tape transport.
2Play time indicator
Shows the elapsed playing time of the cur-
rent side of the tape.
1 Insert a cassette tape into the cassette
loading slot.
Playback will automatically start.
Cassette loading slot
#You can eject a cassette tape by pressing
TAPE EJECT.
2 After a cassette tape has been inserted,
press SOURCE to select the cassette player.
Press SOURCE until you see Cassette dis-
played.
3 Use VOLUME to adjust the sound level.
Rotate it to increase or decrease the volume.
4 To perform fast forward or rewind,
press cor d.
or REW appears in the display.
#To cancel fast forward or rewind and return to
playback, press BAND.
#You can cancel fast forward or rewind by
pressing cor din the same direction twice.
5 To perform forward or rewind music
search, press cor dtwice.
-MS (forward music search) or R-MS (rewind
music search) appears in the display. The cas-
sette player will fast forward or rewind to the
next or previous blank spot on the tape and
begin to play.
#To cancel music search and return to play-
back, press BAND.
#You can cancel music search by pressing cor
din the same direction again.
6 To change the direction of the tape
transport, press BAND.
Notes
!Do not insert anything other than a cassette
tape into the cassette loading slot.
!A cassette left partially inserted after ejection
may incur damage or fall out.
!Play time indicator starts from 0000in the
following cases:
When a tape is inserted
When the tape direction is changed
When you rewind the tape to the begin-
ning
!Play time indicator is halted when fast for-
ward, rewind or music search is operating.
Cassette Player
En
14
Section
05

Intro uction of a vance
cassette player operation
1
234
1B.Skip indicator
Shows when blank skip is turned on.
2unction display
Shows the function status.
32indicator
Shows when Dolby B NR is turned on.
4RPT indicator
Shows when repeat play is turned on.
%Press UNCTION to display the function
names.
Press UNCTION repeatedly to switch be-
tween the following functions:
RPT (repeat play)B.Skip (blank skip)BNR
(Dolby B NR)
#To return to the playback display, press BAND.
Note
If you do not operate the function within about 30
seconds, the display is automatically returned to
the playback display.
Repeating play
Repeat play lets you hear the same track over
again.
1 Press UNCTION to select RPT.
Press UNCTION until RPT appears in the dis-
play.
2 Press ato turn repeat play on.
RPT:ON appears in the display. The track cur-
rently playing will play to the end and then re-
peat.
3 Press bto turn repeat play off.
RPT:O appears in the display. The track cur-
rently playing will continue to play and then
play the next track.
Skipping blank tape sections
Blank skip automatically fast forwards to the
next song if there is a long period of silence
(12 seconds or longer) between songs.
1 Press UNCTION to select B.Skip.
Press UNCTION until B.Skip appears in the
display.
2 Press ato turn blank skip on.
B.Skip:ON appears in the display. Long peri-
ods of silence between songs will be skipped.
3 Press bto turn blank skip off.
B.Skip:O appears in the display. The com-
plete cassette tape will play.
Using Dolby noise re uction
When you listen to tapes that have been re-
corded with Dolby B NR, turn Dolby B NR on.
1 Press UNCTION to select B NR.
Press UNCTION until BNRappears in the
display.
Cassette Player
En 15
English
Section
05

2 Press ato turn Dolby B NR on.
BNR:ONappears in the display. The tape will
play with Dolby B NR on.
3 Press bto turn Dolby B NR off.
BNR:O appears in the display. The tape will
play without Dolby B NR.
Note
Manufactured under license from Dolby Labora-
tories. Dolbyand the double-D symbol are tra-
demarks of Dolby Laboratories.
Cassette Player
En
16
Section
05

Playing a CD
12
These are the basic steps necessary to play a
CD with your built-in CD player. More ad-
vanced CD operation is explained starting on
the next page.
1Play time indicator
Shows the elapsed playing time of the cur-
rent track.
2Track number indicator
Shows the track currently playing.
1 Insert a CD into the CD loading slot.
Playback will automatically start.
CD loading slot
#You can eject a CD by pressing CD EJECT.
2 After a CD has been inserted, press
SOURCE to select the built-in CD player.
3 Use VOLUME to adjust the sound level.
Rotate it to increase or decrease the volume.
4 To perform fast forward or reverse,
press and hold cor d.
#If you select Rough, pressing and holding c
or denables you to search every 10 tracks in the
current disc. (Refer to Selecting the search meth-
od on page 19.)
5 To skip back or forward to another
track, press cor d.
Pressing dskips to the start of the next track.
Pressing conce skips to the start of the cur-
rent track. Pressing again will skip to the pre-
vious track.
Notes
!The built-in CD player plays one, standard, 12-
cm or 8-cm (single) CD at a time. Do not use
an adapter when playing 8-cm CDs.
!Do not insert anything other than a CD into
the CD loading slot.
!If you cannot insert a disc completely or if
after you insert a disc the disc does not play,
check that the label side of the disc is up.
Press CD EJECT to eject the disc, and check
the disc for damage before inserting it again.
!If an error message such as ERROR-11 is dis-
played, refer to Understanding built-in CD
player error messages on page 47.
!When a CD TEXT disc is inserted, the disc and
track titles automatically begin to scroll in the
display. When Ever Scroll is set to ON at the
initial setting, the disc and track titles scroll
continuously. About Ever Scroll, refer to
Switching the ver Scroll on page 44.
Built-in CD Player
En 17
English
Section
06

Intro uction of a vance
built-in CD player operation
12
1unction display
Shows the function status.
2RPT indicator
Shows when repeat play is turned on.
%Press UNCTION to display the function
names.
Press UNCTION repeatedly to switch be-
tween the following functions:
RPT (repeat play)RDM (random play)Scan
(scan play)Pause (pause)COMP (com-
pression and BMX)/REV (search method)
#To return to the playback display, press BAND.
Note
If you do not operate the function within about 30
seconds, the display is automatically returned to
the playback display.
Repeating play
There are two repeat play ranges for the built-
in CD player: DSC (disc repeat) and TRK (one-
track repeat).
1 Press UNCTION to select RPT.
RPT appears in the display.
2 Press cor dto select the repeat range.
Press cor duntil the desired repeat range ap-
pears in the display.
!DSC Repeat the current disc
!TRK Repeat just the current track
Note
If you perform track search or fast forward/re-
verse during TRK, the repeat play range changes
to DSC.
Playing tracks in a ran om
or er
Random play lets you play back tracks on the
CD in a random order.
1 Press UNCTION to select RDM.
Press UNCTION until RDM appears in the
display.
2 Press ato turn random play on.
RDM :ON appears in the display. Tracks will
play in a random order.
3 Press bto turn random play off.
RDM :O appears in the display. Tracks will
continue to play in order.
Scanning tracks of a CD
Scan play lets you hear the first 10 seconds of
each track on the CD.
1 Press UNCTION to select Scan.
Press UNCTION until Scan appears in the
display.
2 Press ato turn scan play on.
Scan :ON appears in the display. The first 10
seconds of each track is played.
Built-in CD Player
En
18
Section
06

3 When you find the desired track press
bto turn scan play off.
Scan :O appears in the display. The track
will continue to play.
#If the display has automatically returned to
the playback display, select Scan again by press-
ing UNCTION.
Note
After scanning of a CD is finished, normal play-
back of the tracks will begin again.
Pausing CD playback
Pause lets you temporarily stop playback of
the CD.
1 Press UNCTION to select Pause.
Press UNCTION until Pause appears in the
display.
2 Press ato turn pause on.
Pause:ON appears in the display. Play of the
current track pauses.
3 Press bto turn pause off.
Pause:O appears in the display. Play will re-
sume at the same point that you turned pause
on.
Using compression an BMX
Using the COMP (compression) and BMX
functions let you adjust the sound playback
quality of this player. Each of the functions
have a two-step adjustment. The COMP func-
tion balances the output of louder and softer
sounds at higher volumes. BMX controls
sound reverberations to give playback a fuller
sound. Listen to each of the effects as you se-
lect through them and use the one that best
enhances the playback of the track or CD that
you are listening to.
1 Press UNCTION to select COMP.
Press UNCTION until COMP appears in the
display.
2 Press aor bto select your favorite set-
ting.
Press aor brepeatedly to switch between the
following settings:
COMP O COMP 1COMP 2
COMP O BMX 1BMX 2
Selecting the search metho
You can switch the search method between
fast forward/reverse and searching every 10
tracks.
1 Press UNCTION to select /REV.
Press UNCTION until /REV appears in the
display.
#If the search method Rough has been pre-
viously selected, Rough will be displayed.
2 Press cor dto select the search meth-
od.
Press cor duntil the desired search method
appears in the display.
!/REV Fast forward and reverse
!Rough Searching every 10 tracks
Built-in CD Player
En 19
English
Section
06

Searching every 10 tracks in
the current isc
If a disc contains over 10 tracks, you can
search every 10 tracks. When a disc contains
a lot of tracks, you can roughly search for the
track you want to play.
1 Select the search method Rough.
Refer to Selecting the search method on the
previous page.
2 Press and hold cor dto search every
10 tracks on a disc.
#If a disc contains less than 10 tracks, pressing
and holding drecalls the last track of the disc.
Also, if the remaining number of tracks after
searching every 10 tracks is less than 10, press-
ing and holding drecalls the last track of the
disc.
#If a disc contains less than 10 tracks, pressing
and holding crecalls the first track of the disc.
Also, if the remaining number of tracks after
searching every 10 tracks is less than 10, press-
ing and holding crecalls the first track of the
disc.
Using isc title functions
You can input CD titles and display the title.
The next time you insert a CD for which you
have entered a title, the title of that CD will be
displayed.
Entering isc titles
Use the disc title input feature to store up to
48 CD titles in the unit. Each title can be up to
8 characters long.
1 Play the CD that you want to enter a
title for.
2 Press UNCTION and hold until Title In
appears in the display.
#When playing a CD TEXT disc, you cannot
switch to Title In. The disc title will have already
been recorded on a CD TEXT disc.
3 Press button 1 to select the desired
character type.
Press button 1repeatedly to switch between
the following character types:
Alphabet (upper case)Alphabet (lower case)
European letters, such as those with ac-
cents (e.g. á,à,ä,ç)Numbers and symbols
#You can select to input numbers and symbols
by pressing button 2.
4 Press aor bto select a letter of the al-
phabet.
Each press of awill display a letter of the al-
phabet in A B C ... X Y Z, numbers and sym-
bols in 1 2 3 ... @ # < order. Each press of b
will display a letter in the reverse order, such
as Z Y X ... C B A.
5 Press dto move the cursor to the next
character position.
When the letter you want is displayed, press d
to move the cursor to the next position and
then select the next letter. Press cto move
backwards in the display.
6 Move the cursor to the last position by
pressing dafter entering the title.
When you press done more time, the entered
title is stored in memory.
7 Press BAND to return to the playback
display.
Built-in CD Player
En
20
Section
06