Pioneer PD-M610 User manual

Operating |
Instructions
MULTI-PLAY COMPACT DISC PLAYER
SI MONEER wummar comeacr owe maven PE MBI
Thank you for. buying this Pioneer product.
Please read through these operating instructions so you will
know how to operate your model properly. After you have
finished reading the instructions, put them away in a safe
place for future reference.
In some countries or regions, the shape of the power plug
and power outlet may sometimes differ from that shown in
the explanatory drawings. However, the method of con-
D-M610
oie
DIGITAL AUDIO
necting and operating the unit is the same.
WARNING :10 prevent FIRE OR SHOCK HAZ-
ARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
IMPORTANT NOTICE
[For U.S. and Canadian modeis]
The serial number for this equipment is located on the rear
panel. Please write this serial number on your enclosed war-
ranty card and keep it in a secure area. This is for your
security.
[For Canadian model]
CAUTION: to prevent ELECTRIC SHOCK DO
NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
EXPOSURE.
ATTENTION: pour prevenin LES cHOcS
ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE
AVEC UN PROLONGATEUR UNE PRISE DE COURANT OU
UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES
PEUVENT ETRE INSEREES A FOND SANS EN LAISSER
AUCUNE PARTIE A DECOUVERT.
’This product is manufactured to comply with the radio inter-
ference requirements of EEC Directive 76/889/EEC and
82/499/ EEC.”
LINE VOLTAGE SELECTOR SWITCH
Only multi-voltage models are provided with this
switch. U.S., Canadian, European, U.K., and Austra-
lian models are not provided with this switch.
Mains voltages in Saudi Arabia are 127V and 220V
only. Never use this model with 110V setting in
Saudi Arabia.
The line voltage selector switch is located on the rear
panel of this player. Before your player is shipped from
the factory, the switch is set to the power require-
ments of the player's destination. Check that it is set
properly before plugging the power cord into the out-
let. If the voltage is not properly set or if you move
to an area where the voltage requirements differ, ad-
just the selector switch as follows:
e Use a medium-sized (flat-blade) screwdriver. Insert
the tip of the screwdriver into the groove of the
selector switch and turn it so that the power vol-
tage marking of your area points to the arrow.
VOLTAGE SELECTOR
@) PIONEER’
The future of sound and vision.

IMPORTANT
1
The
hghtoing
flash
with
atiowtead.
within
ae
equi.
lateral
viangte,
is
intended
t6
alert
the
user
of
the
presence
of
uninsilated:
“dangerous
voltage”
withir:
the
product's:
enélasure:
that’
may
he:
of
sufficient
magnituds:
{6
‘constitute
‘a
risk
of
elects
shock
to
persons,
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO. PREVENT THE RISK OF ELECTRIC SHOCK,
DO"NOT REMOVE COVER (OR: BACK}. NO
USER:SERVICEABLE PARTS: INSIDE: REFER
SERVICING To. ‘QUALIFIED: SERVICE
PERSONNEL.
sink within an
aulateral wuanglie ss
eet of IPE
strc
user of the p
nce
© applance
IMPORTANT 2
Hf the apparatus is fitted with AC mains power out
let(s), see REAR PANEL FACILITIES for convenient
connection
of
additional
Hi-Fi
compotiahtis).
Make
all connections to the AC outlet(s) and thi signal
terminals first. Coemact the plug te the wall socket
last, make sure that the power witch is off
FOR USE IN THE UNITED
KINGDOM
The wires in this main
dance with the folloy
Blue
Brown
colpused In accor
he colous of the wires ia th
apparatus may agi conespond with the colo)
marking identi!ying the tarminals n your plug procend
as follows
The wue which i colowed blue must anpected to
the termindi which 15 marked wath the letter Nor
coloured black
The ware which is coloured brown must be connected
to the ternal which is marked with the letter Lor
coloured ted
Equipment sold in the U.K. is not supplied with
a power plug
READ INSTRUCTIONS ~ All the safety and opera
instructions shauld be rear betore the appkance
is operated
RETAIN INSTRUCTIONS ~ The operating instructions
should be retained for future ret
HEED WARNING » Ail warnings on the
in the operating instructions should be al
FOLLOW INSTRUCTIONS ~ Atloperating
structions should be followed
WATER AND MOISTURE » The appliance shout
be used near water ~ for example, near a bathtub,
washhowl. kitchen sink, laundry tub. ina wet
basement, or near a swimming pool, etc
LOCATION » The auphance should be installed in
stable location:
NALL OF CEILING MOUNTING — The apphance
shauld not be mounted to a veail oF ceding
ZENTILATION The apphance shoutd be situate
that its location «v7 position dogs not interfere with
its proper ventilation, For example, the apphance
should not be situated on a bed, sata. rug, oF simi
lar surtace that may black te ventilation open
1g; OF, placed in a but IN mstattation, sucth
a boukcase or cabimet that may enpede thy
of air through the veritla Hogs
HEAT The appliance should be situated away trom
he
How
rch ae radiators, heat ez
oF other appliances bneludieg am
that aroduce heat
OWER SOURCES — The appliance should be con
Aetiads4
de don the ope
marked on die ayplianc
OWER-CORD PROTECTION — Power supply cords
should
be
routed
so
that
they
are
not
ely
to
he
walked on or pinched by items place
against te
esters
Wiers)
8 pe fo the type
ver supply onty
crib
ating distractions or as
paving particular attentey
plugs, convenence receptacles, and the pov
where they eat fram the applau
OLARIZATION ~ I your purchased pr
ed vath a polarizest power plug, please read the tot
lowing nstructians. This praduct is equpped with
a polarized
an the other), This slug will
© power outlet only one way. This is a
safety feature. If you arg unable to insert the plug
fully
into
the
outie,
try
reversing
the
plug,
if
the
plug shoutd soll fai to fit, contact your elvetrician
bsolete autlet Go not defeat the
safety puepose of the potarized gh
LEANING = The anpiiance should be
with a ai
replace your
waned only
fatit. Never
tivides or
ds
swine
they
may
Conede
the
wig cholo a SOM dry
feuture wax, bengne iy
thar volatile
cabaret
SERVICE ENTRANCE
EQUIPMENT
POWER SERVICE uy
GROUNDING ELECTRODE SYSTEM
(e.g. interior metai water 9.2!
—SAFETY
INSTRUCTIONS
—
POWER LINES ~ An outdoor ant
located away from bre
NONUSE PERIODS -- The power cc
orth
dat ine
ster
be unplugged fro
anused tor a lang period ot tie
OBJECT ANO LIQUID ENTRY © Care shawid by
so that chyects do not fall and liquids &
wito the enclosure through
DAMAGE REQUIRING SERVICE
should be serviced by a "
sentet or qualified ors when:
@ the power-supply cord or the plug has been
famaged. «
® Oblects have tatlen, 0
the appliance. or
@ = The apphance been
@ = The appl
e
vuid has been spilled into
exposed to rain; or
Flot appear to operate normally
ed change in performance: or
The
appliance
has
been
dropped;
or
the
enclosure
damaged
SERVICING ~ The user should not attempt to service
the applence beyond that described in the oper-
sting
instructions,
For
all
other
servicing,
contact
the 9 s1 Pioneer authorized service center
or exhibits 3
GROUND ape
CLAMPS
BONDIty
JUMPER d
FIG.A
INSULATORS b
ANTENNA
LEAD.IN
WIRE
TO EXTERNAL «ff Use juraper wire net se
ANTENNA
TERMINALS OF
PRODUCT
ANTENNA,
SISCHARGE
UNIT ¢ .
7 GROUND:
WIRE ais
i
OUTOOOR ANTENNA GROUNDING — ff en outside
anteana is connected to the antenna terminal. be
sot the anitanna system 1s grounded so as ta pire:
vide some ps against voltage surges and
built up static charges
Inthe U.S.A. section 810 of the National Electr
cal Cade, ANSUNFPA No, 70-1984, prov
information with re # to proper grounding of
the
mast
and
supporting
structure,
grounding
of
the lead-in wire 1 an antenna discharge unit, size
of grounding conductors, lavation of anterina dis
charge unit, connactian to grounding electrodes.
and requiremens for the grounding electrode See
Fig. A
CART. — An appliance and cart combination should be
moved with care, Quick stons. excassive force
and uneven surfaces ray cause the apPMANCE and
cart combination to overtutr
1G AWG
cop:
AWG i8 4 run") alumi-
AWE: 61.0 mm?)
steel, bronee wita, of
asin and
with stand:
snaced for 4 feat
tt
tetarsi te 6
motets? agort
AL antennae descharge unit as.
sly as possible to wh
in enters hou!
BANGS
mney te
wher a separate
grounding
Section @1G Bt yp

and
European
models
Except U.K. ® U.K.
and
European
models only.
@ @: U.S. and Canadian models only
e- oA
ilustration not
a @ applicable to
U.K. model.
3
<PRB1088>
E

Except U.K. and European models
1
cls
i= lls J
SG
Except U.K. and European models
Except U.K. and
European models
4
<PRB1088>
E

[FOR EUROPEAN AND U.K. MODELS]
CAUTION
The following caution labei appear on your player.
Location: rear of the player
This product contains a laser diode of higher class
than 1. To ensure continued safety, do not remove
any covers or attempt to gain access to the inside of
the product.
Refer all servicing to qualified personnel.
CLASS 1. -
LASER PRODUCT
VRW-328
[FOR U.S. MODEL]
CAUTION
e Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous
radiation exposure.
© The use of optical instruments with this product will increase eye hazard.
[For Canadian model]
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Ra-
dio Interference Regulations of the Canadian Department of Communications.
INFORMATION TO USER [FOR U.S. MODEL}
This equipment generates and uses radio frequency
energy and if not installed and used properly, that is, in
strict accordance with the manufacturer's instructions,
may cause interference to radio and television recep-
tion. It has been type tested and found to comply with
the limits for a Class B computing device in accordance
with the specifications in Subpart J of Part 15 of FCC
Rules, which are designed to pravide reasonable pro-
tection against such interference in a residential instal-
lation. However, there is no guarantee that interference
will not occur in a particular installation.
{f this equipment does cause interference to radio or
television reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
@ reorient the receiving antenna
@ relocate this equipment with respect to the receiver
@ move this equipment away from the receiver
@ plug this equipment into a different outlet so that
equipment and receiver are on different branch cir-
cuits.
CONTENTS
If necessary, the user should consult the dealer or an
experienced radio/television technician for additional
suggestions. The user may find the following booklet
prepared by the Federal Communications Commission
helpful
How to Identify and Resolve Radio-TV Interference
Problems
This booklet is available from the US Government
Printing Office, Washington, D.C., 20402, Stock No
004-000-00345-4
The above instructions epply anty ta units which will
be operated in the United States.
FEATURES sittin dem antate poe ae SEES
CAUTIONS REGARDING HANDLING ... .
BEFORE OPERATING THE PLAYER.....
Sra Myres nes yee 5 OPERATION... ..
Fa Muhasisc nae aMee 5 OPERATION WITH A REMOTE CONTROL UNIT
7 CAUTIONS REGARDING USE OF REMOTE CONTROL UNIT . 22
CONNENCTIONS TROUBLESHOOTING 2.2. 2 ee ee ce ee ee 23
NAMES AND USE OF PARTS.........--...-.--------5 9 SPECIFICATIONS»... 0. ce ce eee ee etre eee 24
5
<PRB1088>
E

FEATURES
1. This magazine-type multi-play CD player selects
and plays up to six discs consecutively.
2. A multi-play CD player designed for high-quality
sound using the 8fs digital filter and independent
L/R glitchless twin D/A converter system.
The convenience of CD magazines is combined with a design for
high-quality sound from the nonresonance concept.
° 8 times oversampling digital filter
@ Glitchless twin D/A converter system (independent L/R)
3. Easy-listening play through the remote control
unit featuring one-shot transmission. (Except
U.K. and European models)
After entering the program on the remote contro! unit, while
viewing the LCD screen, the entire program can be transmitted at
the touch of a button,
® Programming for 4 CD magazines for up to 64 steps.
4, Multi-function and multi-play operation with
delete play, delete random play, one-touch fade,
time fade editing and other features.
® Delete play:
After deleting the undesired tracks, only the desired tracks will
be played.
® Delete random play:
After deleting the undesired tracks, only the desired tracks will
be played at random.
® One-touch fade:
Fade-in and fade-out functions can be used for background
music editing.
*° Time fade editing:
Fade-out is done within the specified time. Ideal for tape
recording.
® 32 step program:
32 step programmed playback of desired tracks from six discs.
® Pause program:
For incorporating a pause step into the program.
5. Sound volume can be controlled from the remote
control unit (digital level controller).
Volume selection from 0 dB to ~ 25 dB can be controlled from the
remote control unit.
6. Multi-function display simultaneously shows the
disc number, track number, elapsed time, disc
mark, and output level. 2
The display can be switched to show total time and remaining
time.
7. Disc number keys and track number keys are
seperately arranged on the player and the remote
control unit to facilitate quick selection of discs
and tracks.
8. Headphone jack with volume control.
9. High performance pickup ensures high-fidelity
playback.
CAUTIONS REGARDING HANDLING
LOCATION
Install the player in a well ventilated location where
it will not be exposed to high temperature or
humidity.
Do not install the player in a location which is exposed to direct
rays of.the sun, or near stoves or radiators. Excessive heat can
adversely affect the. cabinet and internal components. Also,
installation of the player in a damp or dusty environment may
result
in
malfunction
or
accident.
(Also
avoid
installation
near
cookers etc,, where the player may be exposed to smoke from
oil, steam or heat.)
6
<PRB1088>
E

CAUTIONS REGARDING HANDLING
PRECAUTIONS REGARDING INSTALLATION
e Placing and using the compact disc player for long periods on
heat-generating sources such as amplifiers will affect
performance. Avoid placing the player on. heat-generating
sources.
* install this compact disc player as far as possible from tuners
and TV sets. A compact disc player installed in close proximity
to such equipment, may cause noise or degradation of the
picture. .
e Such noise may be particularly noticeable when an indoor
antenna is used. In such a case, make use of an outdoor
antenna, or turn off power to the compact disc player.
CONDENSATION
° When this unit is brought into a warm room from previously
cold surroundings or when the room temperature rises sharply,
condensation may form inside, and the unit may not be able to
attain its full performance. In cases like this, allow the unit to
stand for about an hour or raise the room temperature
gradually.
CARE OF DISCS
° With this player, use discs which display the mark shown
below. (Optical audio digital discs.)
olise
DIGITAL AUDIO
* When holding discs, do not touch their signal surfaces. Hold
by the edges, or by one edge and the center hole.
e Do not affix gummed labels or tape to the label surfaces. Also,
do not scratch or damage the label.
e Discs rotate at high speed inside the player. Do not use
damaged (cracked or warped) discs.
CLEANING DISCS
e The presence of fingerprints or smudges on the surface of the
disc will not directly affect the recorded signals, but depending
on the degree of contamination, the brightness of the light
reflected from the signal surfaces may be reduced, causing
degradation of sound quality. Always keep your discs clean by
wiping them gently with a soft cloth from the inner edge
toward the outer periphery.
e Ifadisc becomes very dirty, dip a soft cloth in water, and after
wringing it out well, wipe the dirt away gently, and then
remove any water drops with another soft, dry cloth.
* Do not use record cleaning sprays or anti-static agents on
discs. Also, never clean discs with benzene, thinner, or other
volatile solvents, since damage to the disc surface may result.
STORING DISCS (Storing without using the 6-
disc magazine)
¢ Discs are made of the same kinds of plastic used for
conventional analog audio records. Be careful not to allow
discs to warp; always store discs in their cases vertically,
avoiding locations with high heat or humidity, or extremely
low temperatures. Avoid leaving discs in cars, since the seat
of a car in direct sunlight can become unbelievably hot.
° Always read and abide by the precautionary notes listed on
disc labels.
*® Do not store discs by leaving them in the single-disc magazine.
CLEANING THE PLAYER AND THE MAGAZINE
To clean the PLAYER and the MAGAZINE wipe with a soft, dry
cloth. For stubborn dirt, wet a soft cloth with a mild detergent
solution, wring well, then wipe off the dirt. Also use a dry cloth to
wipe the surface dry. Do not use volatile liquids such as benzene
and thinner which are harmful to the unit.
7
<PRB1088>
E
|

BEFORE OPERATING THE PLAYER
CONFIRM SUPPLIED ACCESSORIES
© Refer to figure [1 on page 3.
@ 6 COMPACT DISC MAGAZINE x 1
{Called 6 disc magazine in the explanatory text.)
@ Output cable x 1
@® SINGLE COMPACT DISC MAGAZINE x 1
{Except U.K. and European models) (Called single-disc
magazine in the explanatory text.}
NOTE:
The supplied 6 disc magazine and single-disc magazine are for 12
cm discs only.
@ Control cord x 1
(U.S. and Canadian models only)
& AAA/ROS dry cell batteries x 2
®© Remote control unit x 1
@® Except U.K. and European models.
®) U.K. and European models only.
INSERT DISCS INTO THE 6 DISC MAGAZINE
© Refer to figure [3] on page 3.
Insert any discs which you may have into the supplied magazine.
Up to six discs may be inserted. The numbering of the discs
begins with 1 at the topmost tray, and then increases in order
from 2 to 6 for the lower trays. The magazine has a window
through which the pulled- out disc tray can be checked. Even
during playback, the number of the disc being played back can be
checked through this window.
1. Pull out only one disc tray.
@ Dise tray
@ Make sure to pull out only 1 disc tray.
2. Position discs with the label side downward.
@) Label side downward
3. Put the disc tray back as it was originally.
4. Insert other discs by repeating steps 1 to 3.
NOTE:
* Please make sure to only pull out ane disc tray at a time.
(When a dise tray has been pulled out, do not pull out other
disc trays.)
® if discs are inserted label side upward, it will not be possible for
them to be played. Please make sure to insert them with the
label side downward.
* Objects other than discs (song cards, explanations of disc
contents, etc.), must never be inserted into the disc trays.
* Do not touch the playing surface of discs {iridescent side) with
hands or fingers.
CAUTIONS REGARDING HANDLING OF
MAGAZINES
*
When
inserting
a
magazine
into
the
player,
make
sure
that
the
direction
of
insertion
is
correct.
°
After
use,
store
in
the
case
provided.
Do
not
place
in
locations
subjected
to
high
temperatures
or
exposed
to
direct
sunlight.
*° Do not take magazines apart.
*
Be
careful
not
to
drop,
or
hit
magazines
against
things.
Also
do
not
apply
strong
force
to
trays
which
have been
withdrawn.
® Application of benzene, thinner, insecticide or other volatile
liquids to a magazine may damage the surface, so keep
magazines away from such substances.
8
<PRB1088 >
E
AFFIXING LABELS TO 6 DISC MAGAZINES
@ When affixing the supplied labels, make sure to affix them to
the specified positions. If fabels or tape are affixed to other
than the specified positions, the magazine and player may not
operate correctly.
*® Each label can be convenientiy used as follows:
A: Titles
B: Names of stored discs and tracks
C: Titles
D: Names of stored discs
E,G,F: Classification
* Do not affix one label on top of another
{However, F and G may be affixed on top of label C).
NOTE:
® In order to play an 8-cm CD you will need a special Multi-Play
Magazine (JD-M108) which is sold separately. Be sure to read
thoroughly the Operating Instructions before using it.
° 8-cm CD Adaptors
it is possible that even an adaptor which meets recommended
standard CD specifications will not be usable with the CD
player. It is recommended that the special Multi-Play Magazine
(JD-M108) be used.
@ Never foad an 8-cm CD or its adaptor into a standard 12-cm
magazine. This may seriously damage the CD player.
* Do not install only an 8-cm disc or only the adapter into the
supplied single-disc magazine.
*° Do not insert only a 8-cm disc and adaptor into the supplied
magazine.
Additional magazines identical to the one supplied are
available as options (* JD-M100, JD-M108}. Please use them
to make your own disc library, with seperate magazines for
each artist or genre.
* IDM 100 oie ee es ae Son, 2 2a Magazine for six 12-cm discs
JD-M108 .........-. Magazine for 8-cm discs
NOTE:
Both 12 cm discs and 8 cm discs cannot be installed together in a
magazine.

CONNECTIONS
For U.S. customers only
You may purchase additional *JD-M100 or JD-M108 six-compact-
disc magazines from your dealer. If however, they are not avail-
able at your dealer in the United States, you may order from:
PIONEER ELECTRONICS SERVICE, INC.
2265 East 220th Street
P.O. Box 1760, Long Beach
CA. 90801-1760
U.S.A.
Phone #[phone]
PUT BATTERIES INTO REMOTE CONTROL
UNIT
e Refer to figure 4 on page 3.
1. Open the rear cover, and install batteries making
sure that the © © polarity is correct.
2, Close the cover.
NOTE:
@ If the remate control unit will not be used for a long time {1
month or more), please remove the batteries to avoid battery
leakage. If fluid should ever leak from batteries, please wipe
away the fluid and then install new batteries.
° Please do not put books etc. on top of the remote control unit.
If keys are continuously depressed the batteries will run down.
Remote control unit of ©-@:
® The LCD display in the remote control unit is extremely
delicate and should not be used in places where the
temperature and humidity is high or extremely cold such as in
cars. It should also be protected from strong shocks.
* Remember that a battery exchange that takes longer than a
few minutes will erase memorized programs.
* When the rear cover is opened, the power will be automatically
turned OFF and the LCD will go OFF. Be sure to close the rear
cover when using the remote control unit.
incorrect use of batteries may result in leakage of fluid,
explosion of batteries and other dangers. Please pay
particular attention to the following points.
© Please cortectly install batteries so that the {+) and (—)
battery polarity matches with the (+) and (—) markings
inside the battery case. -
® Do not use new batteries together with batteries
which have aiready been used.
® The voltages of dry batteries may differ even though they
are of the same size and shape. Piease do not use different
types of dry batteries together.
© Refer to figuré 2 on page 3.
@ Red
® White
© Output cable
@ Make sure not to connect to the record player input terminal
{PHONO}, as sound will be distorted and normal playback will
not be possible.
© CD or AUX terminals
@® Stereo amplifier
® Control cord (U.S. and Canadian models only}
® Controi Terminal (U.S. and Canadian models only)
When using together with Pioneer products marked with the
Si mark, make connections with the supplied control
cord. When this feature is not used, connection is not
necessary.
@ Power cord
@ Household wall outlet
Connencting the output cable
Connect the plugs of the cable to the input terminals of the
amplifier (terminals marked CD or AUX), and to the output
terminals of the compact disc player.
® Connect the white plugs to the left (L) terminals and the red
plugs to the right (R) terminals.
*® Make sure plugs are pushed fully into the terminals.
Connect the power cord
Insert the power cord plug into the auxiliary AC outlet for your
amplifier unit, or into a household wall outlet.
OPERATION BY REMOTE CONTROL OF
STEREO AMPLIFIER
{U.S. and Canadian models only)
When a Stereo amplifier with the Pioneer mark is used,
connect the controi terminal on the rear panel of the player to the
corresponding terminal on the amplifier. This will enable the
player to be controlled from a distance, with the remote control
unit supplied with the stereo amplifier. When this feature is not
used, connection is not necessary.
© The remote contol unit can be used for PLAY, STOP, PAUSE,
TRACK SEARCH and DISC change operations. :
® The control cord is supplied with the player.
¢ For instructions regarding connection and operation, please
refer to the operating instruction manual for your stereo
amplifier.
NOTE:
° The player’s remote sensor does not function when a play is
inserted in the CONTROL IN jack. To operate, point the remote
control unit to the stereo amplifier.
° Make sure to connect the control cord to QUT jack of
CONTROL and IN jack of other components. Both plugs should
be inserted correctly. Never keep the one of the plugs being
unplugged.
9
<PRB1088>
E

JAMES AND USE OF PARTS
RONT
PANEL
@
@
aucun
@®
REMOTE
SENSOR
@)
MANUAL
SEARCH
D
POWER
©
ee
@
pisc
numeer
@)
MAGAZINE
INSERTION
@
RANDOM
GDA
VOMS
SLOT
Ay
@3) STOP
{2) EJECT
) POWER switch
ess to turn power to the unit ON and OFF,
) Magazine insertion slot
) AUTO FADER
“IN key:
ess this key to begin playback with fade-in. (Operable only
iring pause mode).
UT key
ess to begin fade-out. (When fade-out ends, the player will
iter the pause mode.)
) INDICATORS
SC : The disc being played or searched is
displayed.
RACK : The number of the track or program
currently playing is displayed.
» Gan : Lights during repeat playback of one
track.
: Lights during repeat playback of all tracks.
: Lights during random playback.
ME/REMAIN/TOTAL
: Each time the TIME key is pressed, the
display changes accordingly.
TIME : Displays the number and playing time of
the track being played.
REMAIN : The remaining playback time (TRACK
REMAIN) of the track being played is
displayed {in minutes and seconds}.
Pressing the key once will display (in
minutes and seconds) the remaining
playback time (DISC REMAIN) of the disc
being. played.
TOTAL : This displays the total number of tracks
{TRACK) on the disc and the disc’ s total
Playing time in minutes and seconds.
For programmed playback, the remaining time of the track
being played and the total program step (TOTAL) of the
program are displayed
IN
:
Displays
the
minutes
of
the
playback
time
and
remaining
time
of
the
currently
playing track,
)
>RB1088 >
@) CLEAR
@i) TIME FADE EDIT
(6) TRACK =
G
(4 PAUSE ps )
(8) PHONES
(7) PGM
SEC : Displays the seconds of the playback time
and remaining time of the currently
playing track.
iPROGRAM| : Lights when a program mode.
IDELE FE} : Lights when delete mode.
TIME FADE EDIT : Lights when time fade editing has been
set.
LEVEL : The volume level of fade-in, fade- out and
digital level control is displayed.
DISC Symbol : The center bar of the disc symbol for the
disc being played lights in red. When
searching for discs not installed in the
magazine, the corresponding disc mark
will go off.
© TIME key
® Use to select the method for displaying time on the indicator
panel, Each time the key is pressed, the indication changes
from TIME, REMAIN (track remain) and REMAIN (disc remain:
This will not be displayed during programmed playback.) to
TOTAL in that order. (For details coricerning the display
contents, refer to the explanation about the indicators.)
© REPEAT key
Press this key for repeat playback. Pressing the key once, twice,
or three times will change the repeat mode from single track
repeat, all tracks repeat, and repeat playback cancellation.
@ RANDOM PLAY key
Press this key to start random piayback or delete random
playback.
@® REMOTE SENSOR
@ MANUAL SEARCH keys
When the player is in piay or pause modes, these keys are
pressed to perform fast forward or fast reverse operations, to
allow manual searching. These operations are only carried out
during the time either key is pressed.