Pioneer DDJ-SR User manual

VirtualDJ 8 –Pioneer DDJ-SR
1

VirtualDJ 8 –Pioneer DDJ-SR
2
Table of Contents
A. INSTALLATION....................................................................................................................3
Firmware & Drivers ................................................................................................................3
VirtualDJ 8 Setup ...................................................................................................................3
Advanced Setup.....................................................................................................................4
B. MIXER ...................................................................................................................................5
C. DECKS..................................................................................................................................7
D. EFFECTS..............................................................................................................................9
Single FX mode......................................................................................................................9
Multi FX mode......................................................................................................................10
FX Clone & Beats.................................................................................................................11
E. PADS...................................................................................................................................12
Hot Cue mode......................................................................................................................12
Cue Loop mode....................................................................................................................13
Loop Roll mode....................................................................................................................13
Loop mode............................................................................................................................14
Slicer mode...........................................................................................................................14
Sampler & Sampler Velocity mode......................................................................................15
Remix Points mode..............................................................................................................16
F. PAD PLUS...........................................................................................................................16
HotCue Roll mode................................................................................................................16
Trans mode ..........................................................................................................................17
Combo FX mode..................................................................................................................17
Sampler Roll mode...............................................................................................................17
G. Recording & Microphone.................................................................................................18

VirtualDJ 8 –Pioneer DDJ-SR
3
A. INSTALLATION
Firmware & Drivers
Firmware: Update the firmware of the unit to the latest version from
http://pioneerdj.com/support/product.php?c=3205&lang=en&p=DDJ-SR&t=272
Drivers (for Windows only): Install the latest ASIO drivers from
http://pioneerdj.com/support/product.php?c=3206&lang=en&p=DDJ-SR&t=272
No drivers are required for Mac OSX computers
VirtualDJ 8 Setup
Download and install VirtualDJ 8 from
http://www.virtualdj.com/download/index.html
(in case you have not done already)
Once VirtualDJ 8 is launched, a Login Window
will appear. Login with your virtualdj.com
account. A Pro Infinity, a Subscriber or
PLUS License is required to fully use the
Pioneer DDJ-SR. Without any of the above
Licenses, the controller will operate for 10
minutes each time you restart VirtualDJ.
http://www.virtualdj.com/buy/index.html
A detection window will appear next
asking to use or not the pre-defined audio
setup with the built-in sound card of the
DDJ-SR.
You can still change that from Settings-
>AUDIO tab.
The unit is now ready to operate with VirtualDJ.

VirtualDJ 8 –Pioneer DDJ-SR
4
Advanced Setup
MIDI Operation
The unit should be visible in the
CONTROLLERS tab of Config and the
“factory default” available/selected from the
Mappings drop-down list. The factory default
Mapping offers the functions described in
this Manual, however those can be adjusted
to your needs via VDJ Script actions.
Find more details at
http://www.virtualdj.com/wiki/VDJscript.html
AUDIO Setup
The unit has a pre-defined Audio setup and
a special button in the AUDIO tab of Config
to provide that.
Please read the manual of DDJ-SR for
further Audio capabilities-setups.
http://pioneerdj.com/support/product.php?lan
g=en&p=DDJ-SR&t=man
For further software settings please refer to the User Guides of VirtualDJ 8.
http://www.virtualdj.com/wiki/PDFManuals.html

VirtualDJ 8 –Pioneer DDJ-SR
5
B. MIXER
1. CROSSFADER: Blends audio between the left and right channels.
2. VOLUME: Alter the sound of the selected software Deck, depending on the (22)
Deck Selectors. While SHIFT is held down, the VOLUME faders will stop the deck at
the previously selected Cue point when these reach the minimum level (zero) and
will start the deck (synced to the other deck) if those move from the zero position.
(Fader Start)
3. LEVEL METERS VIEW: Switch to MASTER position if you wish the Volume
Indicator LEDs to show the level of the Master Output. Switch to CH1-2 position to
view the outputted level of the left and right selected software decks.
4. PFL. Press this button to send this channel's pre-fader signal to the Cue Channel for
monitoring. When engaged, the button will be lit. Cued deck depends on the (22)
Deck Selectors. Press SHIFT and then one of the PFL buttons to manually tap the
tempo of the loaded track.

VirtualDJ 8 –Pioneer DDJ-SR
6
5. FILTER. Applies a High Pass/Low Pass Filter on the track (middle position is Off
position).
6. EQ-LOW: Adjust the low (bass) frequencies of the corresponding software deck.
7. EQ-MID: Adjust the middle (mid) frequencies of the corresponding software deck
8. EQ-HI: Adjust the high (treble) frequencies of the corresponding software deck
9. TRIM: Adjusts the audio level (gain) of the corresponding software deck.
10. LOAD: Press one of these buttons while a track is selected to load it to left Deck (1
or 3) or right Deck (2 or 4) respectively, depending on the Deck Selectors (22).
Press and hold the same button for more than 1 second, to unload the same deck.
Press SHIFT and the left/right LOAD buttons to sort the tracks of the Songs list by
BPM/Artist to descending or ascending order.
11. BROWSE Knob/push :
Knob: Scrolls through files or folders. When SHIFT is pressed it navigates the
Prelisten position
Push: If focus is on Songs list or Sideview, loads the track to the Prelisten player. If
focus is on the Folders list, enters the Songs List. When SHIFT is pressed, it set
focus to the Folders list or opens/closes subfolders if focus is on the folders list.
12. LOAD PREPARE: Adds the selected track to the Automix list of SideView. When
SHIFT is pressed (AREA), it cycles through the available view of Sideview
(Automix, Sidelist, Sampler, Karaoke, Clone views)
13. BACK: Cycles through the available Browser windows (Folders, Songs, SideView).
When SHIFT is pressed (VIEW) opens/closes the Sideview window of Browser
14. MASTER VOLUME : Adjusts the Master Output Volume (Hardware operation)
15. PHONES VOLUME : Adjusts the Headphones (CUE) Output Volume (Hardware
operation)
16. SAMPLER VOLUME: Adjusts the Master Volume of the Sampler.

VirtualDJ 8 –Pioneer DDJ-SR
7
C. DECKS
17. PLAY: Play/Pauses the track. Hold SHIFT and then press this button to play the
track in Stutter mode (while pressed)
18. CUE: When the Deck is paused, you can set a temporary Cue Point by moving the
Platter to place the Audio Pointer at the desired location and then pressing the Cue
Button. During playback, you can press the Cue Button to return the track to this
Cue Point. (If you did not set a Cue Point, then it will return to the beginning of the
track.). If the Deck is paused, you can press and hold the Cue Button to play the
track from the Temporary Cue Point. Releasing the Cue Button will return the track
to the temporary Cue Point and pause it. To continue playback without returning to
the Temporary Cue Point, press and hold the Cue Button, then press and hold the
Play Button, and then release both buttons.
Hold SHIFT and then press this button to return to the beginning of the track
19. SYNC: Syncs the deck with the opposite one. Hold SHIFT and then press this
button to set the deck as Master Deck. Using 4 decks skins, all other decks will sync
to the Master Deck.

VirtualDJ 8 –Pioneer DDJ-SR
8
20. SHIFT: The SHIFT button if held offers additional functionality to several
buttons/knobs.
21. JOG: Touch sensitive platter for scratching (vinyl mode) or bending (CD Mode).
Hold SHIFT and use the JOG in Seek (Search) mode.
22. DECK SELECTORS: Select the deck you wish to control with both Deck and Mixer
buttons/knobs/faders (1/3 for the left side and 2/4 for the right side).
23. VINYL: Sets the Jog of the deck to Bend (CD) or Scratch (Vinyl) Mode.
24. PITCH FADER : Adjusts the Tempo of the track
25. SLIP: Enables Slip Mode on each deck. Several software functions (such as
Jogwheel movements, HotCues and Loops) will apply temporary on the track, and
the track will return to the position it would have been when those functions are not
triggered.
26. KEYLOCK: Press this button to enable/disable the Master Tempo (Key Lock) of the
deck. Press and hold the same button to reset the Tempo (PITCH) to zero position.
Hold SHIFT and press this button to select one of the available Pitch ranges for the
PITCH/Tempo Slider.
27. PAD PLUS MODE: The PAD MODE is fully supported in VirtualDJ 8, if the unit is
set to the appropriate mode. In this mode, several functions follow the BPM of the
loaded track. See PAD PLUS mode
28. AUTOLOOP: Sets an Auto Loop.
29. 1/2X-2X: Halves/Doubles the size of the Loop. Hold SHIFT and press the 1/2X or
2X buttons to set a Loop In or Loop Out point (for manual looping)
30. LOOP LEDs: The Leds indicate the selected size of the Loop. The 1/ is combined
with other leds to offer sizes less than 1 beat. The + indicates that a loop larger than
32 beats is selected.
31. PARAMETER-/+: These buttons offer different functions depending on the Mode of
the PADs. See PADS.
32. PADS: The 8 PADs offer different functions depending on the Mode of the PADs.
See PADS.

VirtualDJ 8 –Pioneer DDJ-SR
9
D. EFFECTS
The Left FX section (FX1) controls the effects of the Left selected software deck (1 or 3) and
the Right FX section (FX2) controls the effects of the Right selected software deck (2 or 4).
Each one of the FX unit offers 2 modes. The Single Effects mode offers one effect slot but
more parameters controls per effect. The Multi Effects mode offers 3 effect slots (to trigger
more than 1 effect at the same time –chained effects). The selection between those 2
modes is done by pressing the TAP while SHIFT is held.
Single FX mode
Hold SHIFT down and then use the TAP button to select the Single FX mode in the default
GUI. The Single FX mode is selected by default on first launch
Single FX –4 Decks Layout
Single FX –2 Decks Layout

VirtualDJ 8 –Pioneer DDJ-SR
10
In this mode a single Effect is controlled with up to 6 Parameters and 3 Effect buttons. Only
the first 2 Parameters are visible on the GUI. More Parameters and Effect buttons can be
viewed in the FX GUI (opened from the + button on the GUI)
34. FX1 ON. Press this button to enable/disable the selected effect to the Left/Right
selected deck.
Hold SHIFT down and then use this button, to enable/disable the 1st effect button of
the selected effect (if available).
35. FX2 ON. Press this button to select the previous effect from VirtualDJ Effects list.
Hold SHIFT down and then use this button, to enable/disable the 2nd effect button of
the selected effect (if available).
36. FX3 ON. Press this button to select the next effect from VirtualDJ Effects list.
Hold SHIFT down and then use this button, to enable/disable the 3rd effect button of
the selected effect (if available).
38. FX1 knob. Controls the 1st effect parameter of the selected effect.
Hold SHIFT down to control the 4th effect parameter of the selected effect (if available).
39. FX2 knob. Controls the 2nd effect parameter of the selected effect.
Hold SHIFT down to control the 5th effect parameter of the selected effect (if available).
40. FX3 knob. Controls the 3rd effect parameter of the selected effect.
Hold SHIFT down to control the 6th effect parameter of the selected effect (if available).
Multi FX mode
Hold SHIFT down and then use the TAP button to select the Multi FX mode in the default
GUI.
Multi FX mode –4 Decks Layout
Multi FX mode –2 Decks Layout
In this mode 3 different Effects can be applied and controlled with up to 2 Parameters for
each FX slot. Only the first Parameter is visible on the GUI (and the 2nd Parameter while
SHIFT is held on the DDJ-SR). More Parameters and Effect buttons can be viewed in the FX
GUI (opened from the + button on the GUI)

VirtualDJ 8 –Pioneer DDJ-SR
11
34. FX1 ON. Press this button to enable/disable the selected effect of FX slot 1.
33. FX2 ON. Press this button to enable/disable the selected effect of FX slot 2.
34. FX3 ON. Press this button to enable/disable the selected effect of FX slot 3.
38. FX1 knob. Controls the 1st parameter of the selected effect of FX slot 1.
Hold SHIFT to control the 2nd parameter of the selected effect of slot 1.
39. FX2knob. Controls the 1st parameter of the selected effect of FX slot 2.
Hold SHIFT to control the 2nd parameter of the selected effect of slot 2
40. FX3 knob. Controls the 1st parameter of the selected effect of FX slot 3.
Hold SHIFT to control the 2nd parameter of the selected effect of slot 3.
FX Clone & Beats
Starting from VirtualDJ 8.2, the selected Effects from one deck can be cloned (copied) to
any other deck, using the FX ASSIGN buttons.
33. FX ASSIGNS
FX ASSIGN 1 : Clone the selected Effects of Deck 1 to this deck
FX ASSIGN 2 : Clone the selected Effects of Deck 2 to this deck
SHIFT+FX ASSIGN 1 : Clone the selected Effects of Deck 3 to this deck
SHIFT+FX ASSIGN 2 : Clone the selected Effects of Deck 4 to this deck
41. BEATS. Use this knob to adjust the Beats of a Beat-aware Effect.
Currently only the Beats of the Echo effect can be adjusted using this knob. More Beat-aware
Effects will be available in future versions.
42. TAP. Press this button to manually tap the tempo of the track. Press SHIFT and then
this button to toggle between the Single and Multi Effect modes.

VirtualDJ 8 –Pioneer DDJ-SR
12
E. PADS
Pads (32) offer various functions, depending on the PAD MODE buttons. Each of the 4 PAD
MODE buttons offers 2 individual modes (hold SHIFT and then press the PAD MODE button
to access the additional mode). The modes represent a page of the PADS section on the
default VirtualDJ GUI.
Hot Cue mode
Press the HOT CUE mode button to set the PADs to Hot Cue mode.
Hotcues Pads Page –VirtualDJ GUI
Hotcues mode –Pioneer DDJ-SR
Each one of the 8 pad assigns a Hot Cue Point or jumps the track to that Hot Cue Point (if
assigned).
When a Hot Cue Button is unlit, you can assign a Hot Cue Point by pressing it at the desired
point in your track. Once it is assigned, the Hot Cue Button will light on.
Hold SHIFT and then press a pad to delete its assigned Hot Cue Point.
The PARAMETER buttons (31) jump the song to the previous/next assigned HotCue point.
Hold SHIFT and then use the PARAMETER buttons (31) to jump 1 beat backwards/forward.

VirtualDJ 8 –Pioneer DDJ-SR
13
Cue Loop mode
Hold SHIFT and then press the HOT CUE mode button to set the PADs to Cue Loop mode.
The led of the HOT CUE button will blink to indicate this mode.
Cue Loop Pads Page –VirtualDJ GUI
Cue Loop mode –Pioneer DDJ-SR
In this mode each one of the 8 pads assigns a Hot Cue Point or returns the track to that Hot
Cue Point, but in both cases, it also triggers a Loop at that point (momentary or toggle
depending on the selected mode from the Page menu).
Hold SHIFT and then press a pad to stutter/jump to the Hotcue (loop will remain triggered)
Use the PARAMETER buttons (31) to half/double the size of the triggered Loop.
Hold SHIFT and then use the PARAMETER buttons (31) to select the On/Off (Toggle) or
Hold (momentary) Loop trigger mode.
By default the Cue Loops will be quantized. This can be turned off/on from the Page Menu
on the GUI.
Loop Roll mode
Press the ROLL mode button to set the PADs to Loop Roll mode.
Loop Roll mode –VirtualDJ GUI
Loop Roll mode –Pioneer DDJ-SR
Press one of the 8 pads to trigger a momentary Loop Roll. Once the Pad is released, the
track will resume playing from the position it would have been if the Loop Roll was never
triggered. The exit point will be visible on the waveform of the VirtualDJ GUI with an
additional “running” play marker.

VirtualDJ 8 –Pioneer DDJ-SR
14
Hold SHIFT to get a ½, ¾, 1 and 2 beats Loop Roll sizes for the 4 low pads.
Use the Page menu to apply the Loop Rolls to Video.
The PARAMETER buttons (31) are not used in this mode.
Loop mode
Hold SHIFT and then press the ROLL mode button to set the PADs to Loop mode. The led
of the ROLL button will blink to indicate this mode.
Loop Pads page –VirtualDJ GUI
Loop mode –Pioneer DDJ-SR
Press one of the pads to trigger an Auto Loop of a different size in beats, depending on the
selected page. There are 6 different pages available with sizes starting from 1/32 up to 128
beats.
Use the PARAMETER buttons (31) to select the previous/next page with the desired Loop
sizes
Hold SHIFT and then use the PARAMETER buttons (31) to change the behavior of the Loop
pads, by selecting the On/Off (toggle), Hold (momentary –while pad is pressed) or the Roll
mode (track will resume to the position it would have been once the pad is released)
Slicer mode
Press the SLICER mode button to set the PADs to SLICER mode.
Slicer page –VirtualDJ GUI
Slicer mode –Pioneer DDJ-SR

VirtualDJ 8 –Pioneer DDJ-SR
15
The 8 pads represent eight sequential beats—"Slices"—in the Beat Grid. The currently
playing Slice is represented by the currently lit pad. The light will move through the pads as it
progresses through each eight-Slice phrase. Press a pad to repeat that Slice (hold it down if
you want to keep looping it).
Once the Pad is released the track will continue to play from the position it would have been
if the pad was never pressed.
Hold SHIFT and then use the Pads to repeat the memorized Slices (the Slices
played/repeated last time)
Use the PARAMETER (31) buttons to adjust the length of the Loop applied to the slice.
Press SHIFT and then use the PARAMETER (31) buttons to adjust the step of the Slices
Sampler & Sampler Velocity mode
Press the SAMPLER button to set the PADs to Sampler mode.
Sampler Pads page –VirtualDJ GUI
Sampler mode –Pioneer DDJ-SR
Each one of the pads triggers a sample from the selected Sampler Bank of VirtualDJ. If a
bank has less than 9 samples, both sides of the DDJ-SR will control the same samples. If a
bank has more than 8 samples, the left side of the DDJ-SR will control samples 1 to 8 and
the right side samples 9 to 16. The PAD will be lit if a sample slot is loaded and will blink if
triggered.
Press the pads to trigger a sample. Depending on the selected trigger Pad mode, use
SHIFT and the same pads to stop the sample.
Use the PARAMETER (31) buttons to select the Sampler Bank (previous/next). Press
SHIFT and then the PARAMETER (31) buttons to select the Trigger Pad mode (on/off,
hold, stutter, unmute)
Press and hold the SAMPLER Pad mode button to set the PADs to Sampler Velocity
mode. In this mode the Pads will additionally alter the Volume of the triggered Sample
depending on the pressure (velocity).

VirtualDJ 8 –Pioneer DDJ-SR
16
Remix Points mode
Hold SHIFT and then press the SAMPLER mode button to set the PADs to Remix Points
mode. The led of the SAMPLER button will blink to indicate this mode.
Remix Points Pads page –VirtualDJ GUI
Remix Points mode –Pioneer DDJ-SR
This mode offers the first 8 Remix Points of the loaded track. Remix Points are automatically
defined from VirtualDJ, once the track is analyzed. Remix points can be managed from the
POI Editor (more can be added/adjusted/deleted). They usually represent End/Start points of
track’s blocks depending on the structure of the track and are always quantized when
triggered.
The Remix points will be visible on the Song-position progress of the GUI (with white
markers) once the Remix Points Pad page is selected.
F. PAD PLUS
Press the PAD PLUS ON button to enter the PAD PLUS mode. In this mode several
functions of the Pads depend on the tempo of the track. The tempo of the track can be set
manually as well, by tapping the TAP button (at least 4 times). Press and hold the TAP
button (led will turn off) to return to the original tempo (defined by VirtualDJ).
HotCue Roll mode
Press the HOT CUE mode button to set the PADs to HotCue Roll mode.
In this mode the 8 Pads have the same
functionality as the HOTCUE mode. In
addition, the HotCues are triggered
repeatedly (depending on the track’s
tempo), as long as the pad is pressed. The
speed of the trigger (measured in beats) is
controlled by the PARAMETER (31) buttons.
Hold SHIFT and then press a pad to delete
its assigned Hot Cue Point.

VirtualDJ 8 –Pioneer DDJ-SR
17
Trans mode
Press the ROLL mode button to set the PADs to Trans mode.
In this mode the 8 Pads mute the Volume
of the track repeatedly (depending on the
track’s tempo) as long as the pad is
pressed, creating a cut effect. Each one of
the pads offers a different speed (beats) and
the size is displayed on the PARAMETER
digits (see image). The last pad offers a
mute in the Volume of the track (without
repeat).
.
Combo FX mode
Press the SLICER mode button to set the PADs to Combo FX mode.
In this mode the first 3Pads trigger the
corresponding FX slot and additionally they
gradually apply a High Pass Filter (HPF)
to the track, creating a Combo (Chained)
Effect. The HPF can be applied instantly if
the lower 3 Pads are used.
Pads 4 and 8 along with the PARAMETER
(31) buttons are not used (will not affect the
functionality of this mode)
Sampler Roll mode
Press the SAMPLER mode button to set the PADs to Sampler Roll mode.
In this mode the 8 Pads repeatedly trigger
the corresponding Sampler slots
(depending on the track’s tempo) as long as
the pad is pressed, creating a Roll Sample
effect.
The speed of the roll (measured in beats) is
controlled by the PARAMETER (31) buttons
.
Press the pads to trigger a sample.
Depending on the selected trigger Pad
mode, use SHIFT and the same pads to
stop the sample.

VirtualDJ 8 –Pioneer DDJ-SR
18
G. Recording & Microphone
No special configuration is required to record your mix with the DDJ-SR.
Simply open the MASTER center panel of the
VirtualDJ GUI and click to the REC button (or
BCAST for broadcasting) to record your mix.
The Microphone Input of the DDJ-SR is a hardware input. It cannot be control by VirtualDJ
nor can the Microphone Volume knob be assigned to any action. The signal from this input is
routed directly to the Master Output. Therefore, the Microphone input will not be recorded
by default.
The Pioneer DDJ-SR has a dedicated Input to record your Main Mix along with the
Microphone Input, a slight distortion may be present though, and thus this input is not used
by default. If you wish to record both your mix and the Microphone/AUX Input, you will need
to manually add a “record” line in the Audio configuration as followed..
Alternative Audio Configuration for recording Main Mix and Microphone with DDJ-SR
Note: if the record line is not present in the Audio configuration (default configuration), your Mix will be
still recorded but not the Microphone Input.
Hardware Integration Department
2016 - ATOMIX PRODUCTIONS
Reproduction of this manual in full or in part without written permission from Atomix
Productions is prohibited.