Pioneer PDK-TS24 User manual

PDK-TS24
Operating instructions
Mode d’emploi
Bedienungsanleitung
Istruzioni per l’uso
Gebruiksaanwijzing
Manual de instrucciones
Table top stand
Pied de table
Tischständer
Supporto di tavolo
Tafelbladstaander
Soporte de mesa

2
En
Thank you for buying Pioneer’s product.
Please read through the Operating Instructions to learn how
to operate your model safely and properly.
Please be advised to keep the Operating Instructions in your
place for future reference.
Contents
Cautions ...................................................................... 2
Checking the Standard Accessories ......................... 3
Assembling the Stand ............................................... 3
Attaching the Plasma Display ................................... 4
Installing the Product on a TV table etc. ................. 5
Preventing Equipment from Falling Over ................ 6
Specifications ............................................................. 7
Dimensions Diagram ................................................. 7
Installation
• Consult your dealer if you encounter any difficulties with
this installation.
• Pioneer is not liable for any damage resulting from
improper installation, improper use, modification, or
natural disasters.
Cautions
This product is a table top stand exclusively designed for
Plasma Displays (PDP-507XA/PDP-507XD/PDP-507XG/PDP-
4270XA/PDP-4270XD/PDP-427XA/PDP-427XD/PDP-427XG/
PDP-507XDA/PDP-427XDA) from Pioneer. Use with other
model is capable of resulting in instability causing possible
injury. For further information, please contact the store where
you purchased your display.
Do not install or modify the product other than specified. Do
not use this stand for a Plasma Display other than those
designated and do not modify it or use it for other purposes.
Improper installation is extremely dangerous because it may
result in it falling over or other accident.
Installation Location
• Select a location that is strong enough to support the
weight of the stand and the displays.
• Make sure to place it in a level and stable location.
• Do not install it outdoors, at a hot spring, or near a beach.
• Do not install the stand where it may be subjected to
vibration or shock.
Assembling and Installation
•Assemble the stand in accordance with the assembly
instructions and securely attach all screws at the
designated locations.
There have been cases where unforeseen accidents
such as the equipment breaking or falling over oc-
curred after the installation of the display because the
stand was not installed as instructed.
•The display must always be installed by two or more
people to assure it is installed safely.
•Before installation, turn off the power for the display
and peripheral devices then remove the power cord
plug from the power outlet.
Prevent accidents caused by the product falling over by taking
reliable measures to prevent it from falling over (see Page 6).
CAUTION
This symbol refers to a hazard or unsafe practice which
can result in personal injury or property damage.
IMPORTANT NOTICE
Record the model number and serial number of this
equipment below.
Model No. PDK-TS24 Serial No.
Keep these numbers for future use.

3
En
English
Checking the Standard Accessories
Check to make sure that you have all the standard accessories before assembly and installation.
•Base cover x 1 •Stand pipes
(left and right, interchangeable) x 2
•Hexagonal wrench x 1
(Opposite side 6 mm for M8 use)
•Screws 1(4 x 10 mm) x 4
•Installation bolts 2
(M8 x 20 mm: black) x 2
•Installation bolts 3
(M8 x 40 mm: black) x 2
•Operating instructions
(this document) x 1
PDK-TS24
Operating instructions
Mode d’emploi
Bedienungsanleitung
Istruzioni per l’uso
Gebruiksaanwijzing
Manual de instrucciones
Table top stand
Pied de table
Tischständer
Supporto di tavolo
Tafelbladstaander
Soporte de mesa
Assembling the Stand
1Turn the base cover over so the
underside is facing up.
2Insert the stand pipes into the base
cover.
3Tighten the screws to stabilize the
stand pipes.
Base cover
Screws 1
(4 x 10 mm)
Stand pipe
Screws 1
(4 x 10 mm)
Stand pipe
Assembly Procedure

4
En
The weight of a 50 inch Plasma Display is about 34.1 kg (75.2
lbs), that of a 42 inch model is about 29.0 kg (64.0 lbs), they
have no depth, and are unstable. Therefore, at least two
people must assemble and install them.
Note
Insert the bolts in the holes vertically and do not tighten
them with more force than necessary.
Place a sheet or protective cover to protect the display from
scratches or damage.
Assemble only with the Plasma Display lying flat on a table
or similar surface.
Move the stand so that the stand screw holes and the nuts
that connect the main display line up correctly.
1With the Plasma Display lying flat, insert
and secure the two Installation bolts 2(M8
x 20 mm: black) in the holes "a" located in
center of the Plasma Display housing.
At this point, tighten these bolts 2only until the threads
are no longer visible when viewed from the side (you will
be unable to attach the display if the bolts are screwed in
completely).
Attaching the Plasma Display
Regarding the stand pipe screw holes when the
stand is used as a desktop stand
Table: Stand pipe screw holes when the stand is used as a
desktop stand
Plasma Display model
42 inch display model
50 inch display model(except under speaker models)
50 inch display model(under speaker models)
Screw holes used with
stand orientation
A, A'
B, B'
2As shown in the above figure, hook the
stand pipe holes (either pipe Aor B) onto
the screw heads of the installation bolts 2,
then slide the stand upwards to the main
Plasma Display until it engages the installa-
tion bolts 2(once put together with the
display, the stand will slides no more than
19 mm (3/4 inch)).
3Pass the installation bolts 3(M8 x 40 mm:
black) through the stand pipes and tighten
the installation bolts firmly with the
accessory hexagonal wrench (The holes
should be used in the proper combinations,
A–A' and B–B').
4Tighten the installation bolts 2firmly with
the accessory hexagonal wrench.
Caution
Note
When laying down the Plasma Display, be careful so as to not
scratch or damage it.
B
A
B´
A´
B
A
B´
A´
Sheet
Plasma Display
Holes "a"
(holes in center of
Plasma Display)
Installation
bolt 2
Plasma Display
housing
Stop screwing
down the bolt
when the threads
are no longer
visible.
Installation bolt 2
(M8 x 20 mm: black)
Table top stand
Installation bolts 3
(M8 x 40 mm: black)
(Step 3)
Slide the stand
(Step 2)

5
En
English
Installing the Product on a TV table etc.
When installing on a TV table etc., hold the Plasma Display.
If you hold the speakers, they may be damaged or twisted.
Caution
How to hold the PDP-507XA/PDP-507XD/
PDP-507XG/PDP-507XDA(under
speaker models)
Note
Do not hold the under speaker.
How to hold the PDP-507XA/PDP-507XD/
PDP-507XG/PDP-507XDA(except under
speaker models)/PDP-4270XA/PDP-
4270XD/PDP-427XA/PDP-427XD/PDP-
427XG/PDP-427XDA

6
En
11 (13/32)
Side View
12 mm to 15 mm
(1/2 to 5/8 inch)
Using a wall for stabilization
1Attaching falling prevention bolts to the
Plasma Display.
2Using strong cords to firmly stabilize it
appropriately and firmly to a wall, pillar, or
other sturdy element.
Perform this work in the same way on the left and right
sides.
Note
Use hooks, ropes, and fittings
that are available on the market.
Recommended hook:
Nominal diameter M8
Length 12 mm to 15 mm (1/2 to 5/8 inch)
1Hook
2Cords
Fittings
Stabilizing on TV table or other location
Stabilize the equipment as shown in the diagram using
screws that are available on the market.
Note
To stabilize the Plasma Display on a TV table, use screws that
have a nominal diameter of 6 mm (1/4 inch).
Select the appropriate screws after consulting a professional
installer if necessary.
After installing the stand, be sure to take special care to ensure that the equipment will not fall over.
 Because of the plasma display’s weight, if it could fall down, this can result in injury.
 For safety, be sure to take special care to ensure that the Plasma Display will not fall over.
Position of table screws
To stabilize the Plasma Display on a TV table, use screws
that have a nominal diameter of 6 mm (1/4 inch).
Unit: mm (inch)
*: 50 inch display model
**:42 inch display model
301 (11-27/32) 24 (15/16)
120
(4-23/32) 460(18-1/8 )**
552(21-23/32 ) *
Preventing Equipment from Falling Over
Dimension without speakers
Caution
• A TV table with adequate strength should always be
used to support the Plasma Display.
Failure to do so could result in personal injury and
physical damage.
• If you do not take these precautions, the Plasma
Display could fall down and cause injury.
• The screws, hooks and other fittings that you use to
secure the Plasma Display to prevent it from
overturning will vary according to the composition and
thickness of the surface to which it will be attached.
• Select the appropriate screws, hooks and other fittings
after first inspecting the surface carefully to determine
its thickness and composition and after consulting a
professional installer if necessary.
Min. 20 mm
(13/16 inch)
9 mm to 15 mm
(3/8 to 5/8 inch)
6 mm
(1/4 inch)

7
En
English
Specifications
External dimensions 566 mm (W) x 533.5 mm (H) x 325 mm (D) (22-5/16 in. (W) x 21 in. (H) x 12-25/32 in. (D))
Weight 4.1 kg (9.1 lbs)
• The above specifications and exterior may be modified without prior notice to improve the product.
Dimensions Diagram
566 (22-5/16)
325(12-25/32)
1224(48-3/16)
127.5(5)
57.5
(2-9/32)
23(29/32)
115
(4-1/2)
140
(5-1/2)
795 (31-5/16)
46(1-13/16)
841(33-1/8)
150 (5-7/8)
332(13-1/16)
533.5(21)
717(28-1/4)78 (3-1/16)
Unit: mm (inch)
798(31-13/32)
1224(48-3/16)
717(28-7/32)
81(3-3/16)
566(22-5/16)
289.5(11-3/8) 150
(5-7/8)
57.5
(2-9/32)
127.5(5)
325(12-25/32)
115
(4-1/2)
140
(5-1/2)
23(29/32)
533.5(21)
PDP-507XA/PDP-507XD/PDP-507XG/PDP-507XDA(under speaker models)
PDP-507XA/PDP-507XD/PDP-507XG/PDP-507XDA(except under speaker models)

8
En
742(29-7/32)
1040(40-15/16)
679(26-3/4)
63(2-15/32)
566(22-5/16)
289.5(11-3/8) 150
(5-7/8)
57.5
(2-9/32)
127.5(5)
325(12-25/32)
115
(4-1/2)
140
(5-1/2)
23(29/32)
533.5(21)
PDP-4270XA/PDP-4270XD/PDP-427XA/PDP-427XD/PDP-427XG/PDP-427XDA
Dimensions Diagram

9
Fr
Français
Nous vous remercions d’avoir choisi un produit Pioneer.
Veuillez lire attentivement ce mode d’emploi pour savoir
comment utiliser votre support correctement et en toute
sécurité. Nous vous conseillons de conserver soigneusement
ce mode d’emploi àportée de main et dans un endroit sûr
afin de pouvoir vous y référer le cas échéant.
Table des matières
Attention .................................................................. 9
Vérification des pièces fournies........................... 10
Assemblage du support ....................................... 10
Fixation de l’écran àplasma ................................ 11
Installation du produit sur un meuble de télévision,
etc. .......................................................................... 12
Prévenir toute chute de l’équipement ................ 13
Caractéristiques techniques................................. 14
Schéma de dimensions ........................................ 14
Installation
¶En cas de difficultés, veuillez consulter votre revendeur.
¶Pioneer ne saurait être tenu responsable d’aucun
dommage résultant d’une installation ou d’une
utilisation incorrecte de ce produit, de sa modification
ou encore de catastrophes naturelles.
Attention
Ce produit est un support de couverture de table conçu
exclusivement pour les écrans àplasma (PDP-507XA/PDP-
507XD/PDP-507XG/PDP-4270XA/PDP-4270XD/PDP-427XA/
PDP-427XD/PDP-427XG/PDP-507XDA/PDP-427XDA) de
marque Pioneer.
L’utilisation de ce produit avec un autre modèle peut être à
l’origine d’un manque de stabilitépouvant provoquer une
blessure. Pour de plus amples informations, veuillez contacter
le magasin oùvous avez achetévotre écran.
Ne procédez en aucun cas àinstaller ou àmodifier le produit
autrement qu’en suivant les indications fournies. En outre,
n’utilisez pas ce support pour un écran àplasma autre que
celui pour lequel il a étéconçu et ne le modifiez pas ou ne
l’utilisez pas àdes fins autres que celles pour lesquelles il a
étéconçu.
Une installation incorrecte est extrêmement dangereuse car
elle peut provoquer la chute du support ou tout autre
accident.
Lieu d’installation
•Sélectionnez un emplacement assez solide pour supporter
le poids du support et de l’écran.
•Assurez-vous de placer le produit àun emplacement stable
et plat.
•N’installez pas le support àl’extérieur, àproximitéd’une
source thermale ou sur une plage.
•N’installez pas le support àun endroit oùil pourrait être
soumis àdes chocs ou àdes vibrations.
Montage et installation
•Montez le support en suivant les instructions et vissez
solidement toutes les vis aux endroits prévus àcet
effet. Des accidents ont étéconstatés (casse, chute du
matériel, etc.) suite àl’installation de l’écran parce que
le support n’avait pas étéinstalléconformément aux
instructions.
•Pour une bonne installation, l’écran doit toujours être
installépar au moins deux personnes.
•Avant de procéder àl’installation, mettez l’écran ainsi
que les équipements périphériques hors tension en
coupant l’alimentation, puis retirez la prise du câble
d’alimentation de la prise murale.
Prévenez les accidents causés par la chute du produit
en prenant des mesures fiables visant àéviter toute chute
(voir Page 13).
ATTENTION
Ce symbole indique un danger ou une pratique
dangereuse susceptible de provoquer des dommages
corporels ou matériels.
AVIS IMPORTANT
Veuillez prendre note du numéro du modèle et du numéro
de série de cet équipement ci-dessous.
Nºdu modèle. PDK-TS24 Nºde série.
Conservez ces numéros pour pouvoir les utiliser
ultérieurement.

10
Fr
Vérification des pièces fournies
Veuillez vous assurer que vous possédez bien toutes les pièces nécessaires avant de procéder au montage et àl’installation du
support.
Couverture de table x 1 unitéColonnes de support
(gauche et droite, interchangeables) x 2 unités
Cléhexagonale x 1 unité
(Taille en diagonale 6 mm pour
utilisation M8)
Vis 1(4 x 10 mm) x 4 unités
Vis d’installation 2
(M8 x 20 mm : noir) x 2 unités
Vis d’installation 3
(M8 x 40 mm : noir) x 2 unités
Mode d’emploi
(ce document) x 1 exemplaire
PDK-TS24
Operating instructions
Mode d’emploi
Bedienungsanleitung
Istruzioni per l’uso
Gebruiksaanwijzing
Manual de instrucciones
Table top stand
Pied de table
Tischständer
Supporto di tavolo
Tafelbladstaander
Soporte de mesa
Assemblage du support
1Tournez le support de couverture de
table de façon àce que le dessous
regarde vers le haut.
2Insérez les colonnes de support dans
le support de couverture de table.
3Serrez les vis afin de stabiliser les
colonnes de support.
Couverture
de table
Vis 1
(4 x 10 mm)
Colonne de
support
Vis 1
(4 x 10 mm)
Colonne de
support
Procédure de montage