Pioneer CD-R55 User manual

Owner’s Manual
Remote control
CD-R55
Published by Pioneer Corporation.
Copyright © 2006 by Pioneer Corporation.
All rights reserved.
Printed in China
<CZR5072-A> E
<KMMZX> <06K00000>
a
2 3
k
l
j
f
g
h
4
d
e
c
b
8
6
5
7
i
1
9
!When using for the first time, pull out the
film protruding from the tray.
WARNING
!Handling the cord on this product or cords as-
sociated with accessories sold with the pro-
duct may expose you to chemicals listed on
proposition 65 known to the State of California
and other governmental entities to cause can-
cer and birth defects or other reproductive
harm. Wash hands after handling.
!Keep the battery out of the reach of children.
Should the battery be swallowed, immediately
consult a doctor.
CAUTION
!Do not allow this unit to come into contact
with liquids. Electrical shock could result.
Also, this unit damage, smoke, and overheat
could result from contact with liquids.
!Do not disassemble or modify this unit. To do
so may cause a malfunction.
!Always keep the volume low enough so that
you can hear sounds from outside the vehicle.
!Use only one CR2025 (3 V) lithium battery.
!Always check carefully that you are loading
the battery with its plus (+) and minus (–)
poles facing in the proper directions.
!Remove the battery if the remote control is not
used for a month or longer.
!
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
!Do not handle the battery with metallic tools.
!
Do not store the battery with metallic materials.
!In the event of battery leakage, wipe the re-
mote control completely clean and install a
new battery.
!When disposing of used batteries, please
comply with governmental regulations or en-
vironmental public institutions’rules that
apply in your country/area.
!
“Perchlorate Material –special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
(Applicable to California, U.S.A.)”
Using the remote control
Point the remote control in the direction of the
front panel to operate.
!The remote control may not function prop-
erly in direct sunlight.
Important
!Do not store the remote control in high tem-
peratures or direct sunlight.
!Do not let the remote control fall onto the
floor, where it may become jammed under the
brake or accelerator pedal.
Using the remote control
operation mode switch
There are three remote control operation
modes on the remote control.
AVH mode operation
When operating an AV Receiver (e.g., AVH-
P5900DVD) with this remote control, the mode
is normally switched to AVH.
DVD mode operation
When operating a Pioneer DVD player (e.g.,
XDV-P6) with this remote control, the mode is
switched to DVD. If you switch the mode to
DVD, the joystick and 0to 10 operations are
changed for DVD player.
TV mode operation
When operating a Pioneer TV tuner (e.g., GEX-
P5700TV (P)) with this remote control, the
mode is switched to TV. If you switch the
mode to TV, the joystick operation is changed
for TV tuner.
In TV
mode, only buttons shown below can be used.
!SOURCE button
!ATT button
!VOLUME buttons
!Joystick
!DIRECT button
!REAR SOURCE button
Setting remote control
code type
When the remote control operation mode switch is
set to DVD, changing the remote control code type
enables you to operate the Pioneer DVD player with
this remote control. There are three remote codes,
code type A, code type Band code type AVH.
!When operating an AV Receiver (e.g., AVH-
P5900DVD), select code AVH.
!When operating a multi-DVD player (e.g.,
XDV-P6), select code A.
!When operating a DVD navigation unit, se-
lect code B.
1 Set the remote control selection switch
on the left side of the remote control to
the appropriate position with a pen tip or
other pointed instrument .
!If you select AVH mode, there is no need to
take the following procedure.
!If you select A/Bmode, take the following
procedure and change the code type to the
appropriate type.
2 Press 0 and CLEAR on the remote con-
trol simultaneously to change the code
type.
Initially, the code type is set to A. Each time
you press 0and CLEAR simultaneously on the
remote control the code type switches be-
tween Aand B.
Specifications
Power source ............................. 3 V DC (Lithium battery;
CR2025)
Dimensions (W × H × D) ... 54 × 149 × 13 mm
(2-1/8 × 5-7/8 × 1/2 in.)
Weight .......................................... 59 g (2 oz) (including bat-
tery)
Infrared remote control
Wavelength ................................. 945 nm
Output ........................................... typ; 10 mw/sr per Infrared
LED
Note
Specifications and the design are subject to pos-
sible modifications without notice due to im-
provements.
Before You Start
En

If you want to dispose this product, do not mix it
with general household waste. There is a sepa-
rate collection system for used electronic pro-
ducts in accordance with legislation that requires
proper treatment, recovery and recycling.
Private households in the 25 member states of
the EU, in Switzerland and Norway may return
their used electronic products free of charge
to designated collection facilities or to a retai-
ler (if you purchase a similar new one).
For countries not mentioned above, please
contact your local authorities for the correct
method of disposal.
By doing so you will ensure that your disposed
product undergoes the necessary treatment,
recovery and recycling and thus prevent po-
tential negative effects on the environment
and human health.
Information to User
Alteration or modifications carried out without
appropriate authorization may invalidate the
user’s right to operate the equipment.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interfer-
ence, and (2) this device must accept any inter-
ference received, including interference that
may cause undesired operation.
Use and care of the remote
control
Installing the battery (Fig. 1)
Slide the tray out on the back of the remote con-
trol and insert the battery with the plus (+) and
minus (–) poles pointing in the proper direction
.
!When using for the first time, pull out the
film protruding from the tray.
WARNING
!Handling the cord on this product or cords as-
sociated with accessories sold with the pro-
duct may expose you to chemicals listed on
proposition 65 known to the State of California
and other governmental entities to cause can-
cer and birth defects or other reproductive
harm. Wash hands after handling.
!Keep the battery out of the reach of children.
Should the battery be swallowed, immediately
consult a doctor.
CAUTION
!Do not allow this unit to come into contact
with liquids. Electrical shock could result.
Also, this unit damage, smoke, and overheat
could result from contact with liquids.
!Do not disassemble or modify this unit. To do
so may cause a malfunction.
!Always keep the volume low enough so that
you can hear sounds from outside the vehicle.
!Use only one CR2025 (3 V) lithium battery.
!Always check carefully that you are loading
the battery with its plus (+) and minus (–)
poles facing in the proper directions.
!Remove the battery if the remote control is not
used for a month or longer.
!
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
!Do not handle the battery with metallic tools.
!
Do not store the battery with metallic materials.
!In the event of battery leakage, wipe the re-
mote control completely clean and install a
new battery.
!When disposing of used batteries, please
comply with governmental regulations or en-
vironmental public institutions’rules that
apply in your country/area.
!
“Perchlorate Material –special handling may apply.
Using the remote control
Point the remote control in the direction of the
front panel to operate.
Before You Start
!The remote control may not function prop-
erly in direct sunlight.
Important
!Do not store the remote control in high tem-
peratures or direct sunlight.
!Do not let the remote control fall onto the
floor, where it may become jammed under the
brake or accelerator pedal.
Using the remote control
operation mode switch
There are three remote control operation
modes on the remote control.
AVH mode operation
When operating an AV Receiver (e.g., AVH-
P5900DVD) with this remote control, the mode
is normally switched to AVH.
DVD mode operation
When operating a Pioneer DVD player (e.g.,
XDV-P6) with this remote control, the mode is
switched to DVD. If you switch the mode to
DVD, the joystick and 0to 10 operations are
changed for DVD player.
TV mode operation
When operating a Pioneer TV tuner (e.g., GEX-
P5700TV (P)) with this remote control, the
mode is switched to TV. If you switch the
mode to TV, the joystick operation is changed
for TV tuner.
In TV
mode, only buttons shown below can be used.
!SOURCE button
!ATT button
!VOLUME buttons
!Joystick
!DIRECT button
!REAR SOURCE button
Setting remote control
code type
When the remote control operation mode switch is
set to DVD, changing the remote control code type
enables you to operate the Pioneer DVD player with
this remote control. There are three remote codes,
code type A, code type Band code type AVH.
!When operating an AV Receiver (e.g., AVH-
P5900DVD), select code AVH.
!When operating a multi-DVD player (e.g.,
XDV-P6), select code A.
!When operating a DVD navigation unit, se-
lect code B.
1 Set the remote control selection switch
on the left side of the remote control to
the appropriate position with a pen tip or
other pointed instrument .
!If you select AVH mode, there is no need to
take the following procedure.
!If you select A/Bmode, take the following
procedure and change the code type to the
appropriate type.
2 Press 0 and CLEAR on the remote con-
trol simultaneously to change the code
type.
Initially, the code type is set to A. Each time
you press 0and CLEAR simultaneously on the
remote control the code type switches be-
tween Aand B.
Specifications
Power source ............................. 3 V DC (Lithium battery;
CR2025)
Dimensions (W × H × D) ... 54 × 149 × 13 mm
(2-1/8 × 5-7/8 × 1/2 in.)
Weight .......................................... 59 g (2 oz) (including bat-
tery)
Infrared remote control
Wavelength ................................. 945 nm
Output ........................................... typ; 10 mw/sr per Infrared
LED
Note
Specifications and the design are subject to pos-
sible modifications without notice due to im-
provements.
Before You Start

Button names AVH mode DVD mode
1Remote control selec-
tion switch
Switch to change the setting of the remote control. For details, refer to Setting re-
mote control code type.
2 SOURCE button Press to cycle through all the available sources. Press and hold to turn the source
off.
3ATTbutton Press to quickly lower the volume level, by about 90%. Press once more to return to
the original volume level.
4 VOLUME buttons Press to increase or decrease the volume.
5
AUDIO button Press to change the audio language during DVD playback.
SUBTITLE button Press to change the subtitle language during DVD playback.
ANGLE button Press to change the viewing angle during DVD playback.
6 RETURN button Press to display the PBC (playback control) menu during PBC playback.
7a/bbuttons (DISC) Not used.
Remote control code: AVH or B
Not used.
Remote control code: A
Press to select the next/previous disc.
8Remote control opera-
tion mode switch
Switch the operation mode between AVH,DVD and TV modes. Normally, set to
AVH. For details, refer to Using the remote control operation mode switch.
9BOOKMARK button/
PGM button
Press to operate the preprogrammed
functions for each source. For details,
refer to AV Receiver’s operation manual.
Press to turn the bookmark function on
or off when your DVD player features
bookmark function. For details, refer to
DVD player’s operation manual.
10 DIRECT button
In U.S. and Canada:
Press to do direct XM/SIRIUS channel
select.
In other area:
Not used.
Not used.
11 REAR SOURCE button Not used.
Remote control code: AVH
Not used.
Remote control code: Aor B
Press to turn the DVD player on or off.
12 DISPLAY button Press to select different displays.
Remote control code: AVH
Not used.
Remote control code: Aor B
Press to select different displays.
13 ENTERTAINMENT but-
ton Not used.
14 0to 10 buttons, CLEAR
button
Press 0to 10 to input numbers. Buttons
1to 6can operate the preset tuning for
the tuner or disc changing for DVD
player or multi-CD player. Press CLEAR
to clear the input numbers.
Press to select a menu item on the
Video CDs featuring PBC (playback con-
trol).
15 BACK button Press to return to the previous display. Not used.
Button names and
operation (Fig. 2)
16 BAND button
Press to select the tuner band when
tuner is selected as a source. Also used
to cancel the control mode of functions.
Press to switch mode between com-
pressed audio and audio data (CD-DA)
when playing discs with compressed
audio and audio data (CD-DA) such as
CD-EXTRA and MIXED-MODE CDs.
Press to switch mode between com-
pressed audio and audio data (CD-DA)
when playing discs with compressed
audio and audio data (CD-DA) such as
CD-EXTRA and MIXED-MODE CDs.
17
PLAY/PAUSE (f)
button Press to switch sequentially between playback and pause.
REVERSE (m) button Press to perform fast reverse.
FORWARD (n) but-
ton Press to perform fast forward.
PREVIOUS (o) but-
ton Press to return to the previous track (chapter).
NEXT (p) button Press to go to the next track (chapter).
STEP (r/q) buttons Press to move ahead one frame at a time during DVD/VideoCD playback. Press and
hold for one second to activate slow playback.
STOP (g) button Press to stop playback.
18 AUTO PLAY button Press to turn the DVD auto-playback function on or off.
19 a/bbuttons (FOLDER) Press to select the next/previous folder.
20 Joystick
Move to do fast forward, reverse and
track search controls. Click to recall
MENU.
Move to select a menu on the DVD
menu.
21
MENU button Press to display the DVD menu during DVD playback.
TOP MENU (TOP.M)
button Press to return to the top menu during DVD playback.
Button names and
operation (Fig. 2)
Shop the largest selection of reliable car stereos in our online store.