SBL MCBRF-RGBW User manual

Important: Read all instructions prior to installation.
User Manual
Part Number:
4400 Earth City Expy, St. Louis MO 63045 866-590-3533 [email protected]
Parts Included
Installing
MCBRF-RGBW
1. Turn On/Standby
Press 'I' key to turn on unit or press 'O' key to turn off. At power on, unit will
automatically turn on and restore the previous settings.
2. White Mode
These two keys control white LED working mode. Press 'WHITE ONLY' key,
all RGB colors will turn off and only white LED lights up. Press 'WHITE OFF'
key, the white LED will turn off and RGB LED remains on it's previous status.
3. White Brightness
Adjust white LED brightness. Press the right side key to increase white LED
brightness and the left side key to decrease white LED brightness.
4. Static RGB Color Selection
These keys control the RGB static color.
a) Pressing the color printed keys will set the RGB LEDs to correspond color
light as the key. There are 6 shortcut color keys to make direct color selection.
b) Press 'COLOR+' and 'COLOR-' to scroll over all preset static colors,
including the 6 shortcut key colors.
5. Color Brightness
Adjust RGB color brightness. Press the right side key to increase RGB LED
brightness and the left side key to decrease RGB LED brightness.
6. RGB Dynamic Modes Control
These keys control the RGB dynamic modes.
a) Press 'MODE+' and 'MODE-' key to select preset dynamic modes.
b) Press 'SPEED+' and 'SPEED-' to control the dynamic mode running speed.
7. Remote Controller Indicator
The blue indicator will blink when remote control is transmitting a command.
The remote controller works at radio frequency. The remote controller's use is
not restricted by normal obstructions such as walls, doors, etc.
1 - LED Controller
1 - Wireless Remote
1 - CR2025 3V Battery
Functions
Specications
Dynamic Mode 34 modes
Static Color 30 colors
PWM Grade 256 Steps
White Brightness Grade 10 levels
Color Brightness Grade 5 levels
Speed Grade 10 levels
Direct Color Select 6 direct keys
Overload protection Yes
Overheat protection Yes
Working Voltage DC 6-24V
Battery 3V CR2025
Remote frequency 433.92MHz
Remote control distance >15m at open area
Rate Output Current 3x2.5A + 4A
IP Rating IP68
FCC ID 2ACJPRM06
8. Power Supply Wiring
The red power cable should be connected to power positive and black to negative.
The controller unit can work from DC 6V to 24V, Please make sure the power supply
voltage is same as the LED load and the power supply is adequite for the circuit.
9. LED Ouput Wiring
This controller supports constant voltage driving LED products with a
common anode connection. The black cable on the ouput side is the
common anode, it connects to the power supply positive inside the
controller. The white, green, red and blue cable runs the driving signal
of relevant LED color, please connect the color cable to the cathode of
relevant color LED loads and the black cable to the common anode.
10. Status Indicator
The is a full color status indicator. It displays all working statuses of the controller. It
indicates different events as following:
Blue: normal working.
Short single white ash: new command executed.
Long single white ash: reach mode or color cycle edge.
Long single yellow ash: reach speed or brightness limit.
Red ash: overload protected.
Yellow ash: overheat protected.
RGBW LED Controller with Wireless RF Remote

Important: Read all instructions prior to installation.
RGB LED Controller with Wireless RF Remote
User Manual
Part Number:
4400 Earth City Expy, St. Louis MO 63045 866-590-3533 [email protected]
MCBRF-RGBW
12. Waterproof
The MCBRF-RGBW LED controller is fully waterproof with IP68 standard, and can
be used under water within a depth of 30 meters.
Note: The remote receiving sensitivity will decrease when controller is installed in a
wet environment.
13. Protection
This controller has full protection function for output short circuit, overload, and
overheat. The controller will automatically recover from protection when working
status is good.
Please ensure the LED loads are in rated range, outputs are not shorted and the
controller unit is in a good heat dissipation environment.
Advanced Features
FCC Statement
Operation
11. Using Remote
Please remove the battery insulator before using. The remote uses a 3V CR2025
battery. The RF wireless remote signal can pass through most materials. For proper
receiving of the remote signal, please do not install the controller in metal enclosures.
11. Pairing New Remote
The remote and the controller is 1 to 1 paired as default. Further more, one master
unit can be paired to 5 remote controllers and every remote can be paired to any
master unit.
Please do the following steps to pair the new remote to the controller.
1) Turn off the power of the main unit and turn back on after 5 seconds.
2) Press remote 'ON' and 'White Bright +' key together in 5 seconds after power is
restored , and then press 'RED' key in for another 5 seconds.
After this operation, the main unit indicator will ash white for 3 times to display the
command is accepted, the main unit now recognizes the new remote. Only 5 latest
paired remote controllers can be recognized by the controller.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation. Any changes or modications in construction
of this device which are not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.