Pioneer VSX-D6025 User manual

Operating
Instructions
WD PHONEER srecreee arones necoves WSX-D7025
DEMO MODE
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how
to operate your model properly. After you have finished reading the
instructions, put them away in a safe place for future reference.
In some countries or regions, the shape of the power plug and power
outlet may sometimes differ from that shown in the explanatory
drawings. However, the method of connecting and operating the unit
is the same.
WARNING: To PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT NOTICE
[For U.S. and Canadian models]
The serial number for this equipment is located on the rear panel. Piease
write this serial number on your enclosed warranty card and keep it in
a secure area. This is for your security.
Note to CATV system installer
This reminder is provided to call the CATV systern installer’s attention
to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point
of cable entry as practical.
* The demonstration mode is activated by turning on the power:
switch while holding down the RETURN button (from power
standby condition). The demonstration will appear on the display.
© Press the POWER switch to cancel the demonstration.
© Activating the demonstration mode causes memory contents to
return to their original default condition except tuner.
AUDIO/VIDEO STEREO RECEIVER
V9SX-D6025
VSX-D7025
* Illustration shows model VSX-D702S.
[For Canadian model]
CAUTION: To PREVENT ELECTRIC SHOCK DO NOT USE THIS
(POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR
OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
ATTENTION: pour PREVENIR LES CHOCS ELECTRIQUES NE
PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR
UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT,
SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN
LAISSER AUCUNE PARTIE A DECOUVERT.
RETURN function
This function returns the unit to a set of initial settings and ready
to broadcast tuner. This is helpful during troubleshooting or when
no sound is output. For details, refer to page 20.
@ PIONEER’
The Art of Entertainment

IMPORTANT
The lightning flash with arrowhead, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated ‘‘dangerous voltage’ within the product's
enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
READ INSTRUCTIONS — All the safety and operating
instructions should be read before the appliance is
operated.
RETAIN INSTRUCTIONS — The safety and operating
instructions should be retained for future
reference. .
HEED WARNING — Ali warnings on the appliance andin
the operating instructions should be adhered to.
FOLLOW INSTRUCTIONS — Al! operating and use
instructions should be followed.
WATER AND MOISTURE — The appliance shouid not
be used near water — for example, near a bathtub,
washbowl, kitchen sink, Jaundry tub, in a wet
basement, or near a swimming pool, etc.
LOCATION ~ The appliance should be instalied in a
stable location.
WALL OR CEILING MOUNTING — The appliance
should not be mounted to a wall or ceiling.
VENTILATION ~ The appliance should be situated so
that its location or position does not interfere with
its proper ventilation. For example, the appliance
should not be situated ona bed, sofa, rug, or similar
surface that may block the ventilation openings; or,
placed in a built-in installation, such as a bookcase
or cabinet that may impede the flow of air through
the ventilation openings.
HEAT — The appliance should be situated away from
heat sources such as radiators, heat registers,
stoves, or other appliances {inciuding amplifiers}
that produce heat.
POWER SOURCES — The appliance should be
connected to a power supply only of the type
described in the operating instructions or as
marked on the appliance,
POWER-CORD PROTECTION — Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them. Pay particular attention to cords at
plugs, convenience receptacles, and the point
where they exit from the appliance.
POLARIZATION .— If your purchased product is
provided with a polarized power plug, please read
the following instructions. This productis equipped
with a polarized alternating currentline plug (a plug
having one blade wider than the other). This plug
will fit into the power outlet only one way. This is a
safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
CLEANING — The appliance should be cieaned oniy
with a polishing cloth or a soft dry cloth. Never
clean with furniture wax, benzine, insecticides or
other volatile liquids since they may corrode the
cabinet.
ACCESSORY ITEMS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL,
SAFETY INSTRUCTIONS
POWER LINES — An outdoor antenna should be located
away from power lines.
NONUSE PERIODS — The power cord of the appliance
should be unplugged from the outlet when left
unused for a long period of time.
OBJECT AND LIQUID ENTRY — Care should be taken
so that objects do not fall and liquids are not spilled
into the enclosure through openings.
DAMAGE REQUIRING SERVICE — The appliance
should be serviced by a Pioneer authorized service
center or qualified service personnel when:
The power-supply cord or the plug has been
damaged.
Objects have fallen, or tiquid has been spitled into
the appliance.
The appliance has been exposed to rain.
The appliance does not appear to operate normally
or exhibits a marked change in performance.
The appliance has been dropped or the enclosure
damaged.
SERVICING — The user should not attempt to service
the appliance beyond that described in the
operating instructions. All other servicing should
be referred to quatified service personnel.
ELECTRIC
SERVICE
GROUND CLAMPS
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
OUTDOOR ANTENNA GROUNDING — /f an outside
antenna is connected to the antenna terminal, be
sure the antenna system is grounded so as to
provide some protection against voltage surges
and built-up static charges.
In the U.S.A. section 810 of the National Electrical
Code, ANSI/NFPA 70, provides information with
respect to proper grounding of the mast and
supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and
requirements for the grounding electrode. See Fig.
A.
CART — An appliance and cart combination should be
moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart
combination to overturn.
NEC — NATIONAL ELECTRIC CODE
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810 — 20)
GROUNDING CONDUCTORS
(NEC SECTION 810 — 21)
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
FIG. A (NEC ART 250, PART H)
FM T-type Antenna
2
<ARB1421>
AM Loop Antenna
" Audio/Video programmable
remote control unit
Alkaline dry cell batteries
(size “AA” (LR6/AM-3))

CONTENTS
BEFORE OPERATION, ADJUST THE POSITION OF THESE SWITCHES .............cccesecesecescesscesscucsens 4
FEATURES vas ties Sa shea ee cn dew ene ieee Maelo ot asta ocveuc botedarec cuba led clea see seca cuSeveweddecbedocawersedewacececassou 4
BLOCK DIAGRAM) «.ccssccesccclendeiiccs iotetc.Neeeeed cence edeedat oxen des edudeen cde Gdeccustecess cad coasdoescdsuedsuslleseues 5
SURROUND: EFFECT ss ccsieacccesussess coaaveus sacs adevaisedenbacseedans gcsnodbane Soars uated M deceaebebcauetebacbeudaygeeoeess 5
DOLBY: SCH LOGIC | 2. iecsnsccieis sencncel date cab eoeedi rede cectesasnns voatedds avec tddeas ge eeevees Sivbe ets degaddeesesdensees 6
DOLBY PRO LOGIC SURROUND, DOLBY 3CH LOGIC CENTER MOD ...........cccssescecesvcnsccveneecncers 6
SPEAKER: INSTALLATION: sccccecscctca leew cateedscuccediucdss ouadtecssaecavswencgedevacvasegeasbecstestevlteleseeeticunees 6
SIMULATED: STEREO s.sscictccletscooueas eavsab cule stees dds sdeonevaduae oodveuavscendevadeuss vaaseubcs sence adsedeedesasbouses 6
CONNECTIONS (SSeeeepereeee leer lereenreslesneee Udvanccungdsussecccesncseeddieesevewendeawiceseecetedessedec 7
Basic AUdIO SYSTEM CONNECTIONS...........cccecsccesscesscceaucuscetscseserversenseceacausececusuceeseseeceteaesarecens 8
Basic Video SYSteM COMNMECTIONS...........cccesccesecereecceeesecneeeenesecebeneseeeeneaeeseesseeesesesesesersaneaesues 9
Speaker CONMMECHONS 6.055 iscensdecdesssvescvaccscvcclevereddeseccsduscccndesubvcadeesesesessesGecasoscéesveisuveasecsaees 10
ADDIIGATIONS . « isxseucss ocssonesdvcaceeuetenleescsvaceswsi debe csedevon neu cd cosuueveneudnbeesexesOscous ccvcosadecstveerss meses 12
MUltI-ROOM CONNECTIONS ses scscceess cases avis vsususcvceescatesvedcoccspsvaeceudebeseseawsveiededaneveate vase sdeneuevevs 14
Ta eo teter hee eS ae OT EC PETER SRO HET 15
FRONT PANEL FACILITIES [iRXeRsRRepnnnp ne penreE eee pe tee pep Sl pee t Stes SSS StS senses Ses S sesso oes essen nee 18
Segoe se cite ne cases veoibe ae tag tice ieee erence sey bedi age dasa taoessaney mse souatantaaees 22
DIREGT AGCESS TUNING ciccoecedaeieaacelcnekd vz vabees oa ceaeucccaie ccecvedsacvescueddecwiccoseaeeduatedoveeeute essa onres 22
AUTO“ TUNING hisdcesssviesusedaciecsccdasaducectevscesastecwesssvasee raven soasecesaessehs veugdeccwocsed ves Succes veewsaeeee 22
MANUAL, TUNING: viscscccsctescswsieccccsivedocsacececcnesdusbewadesescdcecubescaves sets caevavbessecacacuavescettecscssatect 23
PRESET TUNING icccsscienssevesscceccd caved evessnsaveccevevouscabusccvcedbusasdébaseatebsseeessecsoscocapssvesccdsvevcesddess 23
HITS (Hyper Intelligent Tuning System) .............ccccscseceeceececcsceeccateeseesecpenseesuceeceusecetcetecserseess 24
RECEIVING FM SIMULCAST TV PROGRAMG ..........csccsccvessccecrecesccessetecserersetssonenececnteeseeeuteeass 25
OPERATING THE AUDIO/VIDEO COMPONENTS [Iie eter Eee et ell seSte else ns snene 25
PLAY BAGK, sccscsescdicesecceieutisces becca ssuneeced cneavedevavevaresadeoes cvscubibed es ses stegunetedeuegelSceeaiaweaanvetels 25
RECORDING WITH A CASSETTE DECK .........cccccscsececsecseccecscesscceseeesecnesusessuseecenensteneestererses 26
VIDEO: RECORDING i iccais ccdtcidecnedicacdciwcd clveGenedwsncece icesedvebais ces tactencoeded acevo Masvevaasdusdencselsaates 26
DOLBY PRO LOGIC SURROUND, PRO LOGIC THEATER AND DOLBY 3CH LOGIC [Rees 27
SIMULATED SURROUND, DANCE, HALL, THEATER, JAZZ, CHURCH [iRSREEpeeeeeEee 27
HOW TO USE THE ACOUSTIC MEMORY [BRR pen SED En pS Dry pS Sleep nls tsps sent snsss essen 28
USING THE VIDEO SIGNAL SELECTOR Ss ssissRRRRRRNRnREE pene StS peter DSS n=O ent ssn nies ssn nse nnn nna 28
USING THE AUTO SOURCE CONTROL [iSRRRRINRRERnEEn Ee pnE pelt ert S sete ole essen ese e ene 29
HINTS FOR BETTER RECEPTION...........:.:sccssccscscuseccesceeessceeeesseeenesesaesersceuseescesueecaeeetseseensnage 30
REMOTE CONTROL OPERATION [RRRaRRRRpRRNE REE yr Erne erg e pepe nts essen nese none 31
Receiver Control DUttONS .........cesececsesserscnenccecseeseeneaesnscseneaeeseneeneesesseeseeoeceeseneatateeoeseeeaeeateas 32
Operating other COMPONENHS .........ccececscesececececeseeescecscneeeeeesesetseeuecececeuseceteceeereetscseeseetenanens 33
PFOGTAMIMING cs: cceabe don cacesaenesSecnee stuabaceasteteasdsedescesceeadsnvesndhencdedac doses edeseeceastecesss seeassereadeas 36
ON SCREEN DISPLAY (vSx-D702S U.S. and Canadian models only) JBEEEEEEEEEEEEER EE EEE EEE EERE EEE Eee Ee eee ree 40
TROUBLESHOOTING accccecececisacccscacasicscaieccenssivspccnensvavevedennescdaaccdcedesdasduesotdcevsssdcscecrsecvensess 41
SPECIFICATIONS 2.0. ssiveccicedessssievecsriesecvenncececdaena dees cousins cS Paealcva nase uctesseveeuswecsVousaaeatuuns teas rer 43
Information to User
Alteration or modifications carried out without appropriate authorization may invalidate the user's right to operate the equipment.
3
<ARB1421>

BEFORE OPERATING, ADJUST THE POSITION OF THESE SWITCHES
TWO VOLTAGE SELECTOR SWITCHES
Only multi-voltage models are provided with these switches. U.S.,
Canadian, European, U.K. and Australian models are not provided with
these switches.
Main voltages in Saudi Arabia are 127 V and 220 V only. Never use
this model with 110 V setting in Saudi Arabia.
The line voltage selector switches are on the rear panel. Before your
model is shipped from the factory, these switches are set to the power
requirements of the destination. Check that they are set properly before
plugging the power cord into the household wall socket. If the voltage
is not properly set or if you move to an area where the voltage
requirements differ, adjust the selector switches as follows.
1. Use a medium-size screwdriver.
2. First, insert a screwdriver in the groove of the voltage selector at
the right, and adjust so that the tip of the groove points to the voltage
value of your area.
3. Next, insert a screwdriver in the groove of the voltage selector at
the left and adjust until the voltage is the same as at the right.
TWO VOLTAGE SELECTORS
110V
120-127V
:
ae 220V
240vV
110V 120-127V
SEE INSTRUCTION MANUAL
VOLTAGE SELECTORS
NOTE:
Both switches must be in the same switch
setting; otherwise, unit can be damaged.
FEATURES
The VSX-D702S/VSX-D602S combines the functions of receiver,
wireless remote control, audio-visual selector and surround processor.
It will play a central role in your enjoyment of audio-video media.
¢ DOLBY PRO LOGIC SURROUND performed by a
Digital Signa! Processor (DSP).
e DSP provides Sound Field Control (SFC)
simulated surround settings.
e LARGE, MOTOR-DRIVEN VOLUME KNOB
The large volume knob contributes to operational convenience and
positive response. You can even operate it via remote control. When
you change the volume setting using the remote control unit, the knob
turns by itself, making it easy to keep track of the current setting.
e VIDEO SIGNAL SELECTOR (Simulcast function)
Allows free combination of various audio-visual sources during playback
and over-dubbing, enabling you to produce your own original video
product.
e TWO-WAY VCR COPYING AND MONITORING
VCR 1 — VCR 2: Copying of video cassette tapes can be performed
in either direction.
LD, TV, VIDEO — VCR 1, VCR 2: Allows simultaneous production of
two copies from video disc or compact disc with video.
¢ ACOUSTIC MEMORY FUNCTION
Five types (A—E) of tone control settings can be preset. The settings for
loudness and flat tone response functions can also be selected quickly.
4
_<ARB1421>
E CAUTION: TWO VOLTAGE SELECTORS
8
CHANNEL STEP/FM DE EMPHASIS SWITCH
(Not available on U.S. and Canadian models)
The unit has been factory preset to the channel allocation and de-
emphasis value for the area in which it is to be sold. If these values are
set incorrectly, the frequency display may stop at the wrong frequency,
or sound may be distorted, resulting in an inability to reproduce reception
signals at their proper sound quality. For this reason, be sure to confirm
that the values are set correctly before first using the unit.
[FM 100 kHz/75 us, AM 10 kHz] position:
Setto this position for areas with an FM reception step of 100 kHz, de-
emphasis 75 ps and AM 10 kHz.
[FM 50 kH2/50 us, AM 9 kHz] position:
Setto this position, for areas with an FM reception step of 50 kHz, de-
emphasis 50 ps and AM 9 kHz.
NOTE:
When unsure about the channel allocation and de-emphasis values for
your area, consult your dealer for correct information.
CHANNEL STEP/
FM DE-
EMPHASIS
50kHz
/50uS —@ @- SkHz
100kHz—@ @= 1 OkHz
/75a4S
FM AM
8
¢ CUSTOM MEMORY FUNCTION
Stations can be preset according to the genre of the material broadcast,
and Memory Scan of a particular genre can be carried out.
¢ 90/60/30-MINUTE SLEEP TIMER FUNCTION
¢ MULTI-ROOM REMOTE JACK
The optional MR-100 Multi-room remote control unit can be connected
to the Multi-room remote IN jack.
e AV PROGRAMMABLE REMOTE CONTROL UNIT
With the attached programmable remote control unit, you can operate
any Pioneer audio or video component bearing the qj mark.
If you use the LEARN function, remote commands of components not
bearing the fj] mark can be memorized, giving you remote control over
@ component’s functions.
You can also use the MULTI-COMMAND to memorize up to seven
commands in order, letting you transmit them at the push of a single
button.

BLOCK DIAGRAM
TAPED
AUDIO EC PLAY
cEnten
eeveL
> 2
cease
SURROUND EFFECT
This
unit
is
equipped
with
DOLBY
PRO
LOGIC
SURROUND.
There’s
also
a
DSP
(Digital
Signal
Processor),
with
a
choice
of
five
SFC
(Sound
Field
Control)
simulated
surround
settings.
© SIMULATED SURROUND:
The
“SIMULATED”
creates
effects
of
reverberated
and
reflected
sound
from
the
wails
and
ceiling
similar
to
a
concert
hall.
These
sound-effects
added
to
the
actual
sound
from
the
source
make
you
feel
as
if
you
were
in
a
more
expanded
space.
Choose
the
SIMULATED
SURROUND
mode
if
the
source
sound
signal
is
mono.
© JAZZ:
This gives you the sound field of a jazz club.
¢ CHURCH:
The
sound
field
of
a
church,
ideal
for
reproducing
the
rich
sound
of
a
pipe organ.
* DANCE:
A
“‘hot”’
high-energy
sound,
with
extra
reverb
for
greater
ambience.
* HALL:
You can enjoy a convincing hall sound.
© THEATER:
Use
this
when
watching
a
movie
sources
that
have
a
stereo
soundtrack
to enjoy the effect of being in a movie theater.
PRE OUT FRONT
: VSX-D702S H
: US. and Canadian }
H models only. '
* PRO LOGIC THEATER
Use
with
video
software
bearing
the
[J){]
mark.
The
feeling
of
movement,
and
outstanding
stereo
imaging
offered
by
DOLBY
PRO
LOGIC
SURROUND,
together
with
atmosphere
of
a
movie
theater
assure
incredible
ambience.
* DOLBY PRO LOGIC SURROUND
Choose
this
setting
for
movies
and
music
(especially
Video
Discs
and
video
tapes
bearing
the
[](][po.sy
surround]
mark)
playback.
DOLBY
PRO
LOGIC
SURROUND
continuously
detects
the
size
and
direction
of
the
dominant
signal
and
cancels
undesirable
crosstalk,
thereby
providing
signal
emphasis.
You
can
clearly
perceive
the
directions
and
source
of
the
music.
Real
flow
of
sound
can
also
be
re-created
naturally
using
this
feature.
It
gives
the
feeling
of
being
in
an
outstanding
and
expansive
sound
field.
When
using
DOLBY
PRO
LOGIC
SURROUND,
a
delay
time
setting
of
20
ms
is
commonly
used.
Use
a
different
setting
if
you
prefer.
NOTE:
DOLBY
PRO
LOGIC
SURROUND
can
be
left
ON
with
stereo
sources
not
bearing
the
[(]|[posy surround]
mark.
However,
with
monaural
Sources,
there
is
only
sound
from
the
center
speaker,
so
switch
to
SIMULATED
SURROUND.
Note:
Doiby
Surround
will
not
operate
correctly
if
the
signal
passes
through
a graphic equalizer.
When
using
Dolby
Surround,
turn
off
the
TAPE
2
MONITOR
or
set
the
graphic
equalizer
for
flat
response
or
to
its
“through”
(or
off)
setting,
if
you
have
one
in
use.
*x 2
Manufactured
under
license
from
Dolby
Laboratories
Licensing
Corporation.
Additionally
licensed
under
one
or
more
of
the
following
patents:
U.S.
number
3,959,590:
Canadian
numbers
1,004,603
and
1,037,877.
“Dolby”,
“Pro
Logic”,
and
the
double-D
symbol
are
trademarks
of
Dolby
Laboratories
Licensing
Corporation.
*
Fabriqué
sous
licence
de
Dolby
Laboratories
Licensing
Corporation
et
sous
un
ou
plusiers
des
brevets
suivants:
U.S.A:
3,959,590;
Canada
1,004,603
et
1,037,877.
“‘DOLBY.’Pro
Logic,’
et
le
symbole
double-D
sont
des
marques
de
Dolby
Laboratories
Licensing
Corporation.”
:
5
<ARB1421>

DOLBY 3CH LOGIC
Combining the rear speaker signal with that of the front speakers results
in your being able to enjoy a regenerated sound field which has
comparatively more presence and a more expansive feeling from the
front 3 channels (front L, front R, and center speakers) than that of
ordinary stereo regeneration.
DOLBY 3CH LOGIC can be used with stereo sources not encoded with
DOLBY SURROUND.
DOLBY PRO LOGIC SURROUND, DOLBY 3CH LOGIC CENTER MODE
You can choose from the following settings:
Center Mode Choices:
When using a center speaker:
e NORMAL -- Low range frequencies, which have little effect on
directionality and positioning, are routed to the left and right front
speakers. So you can use a relatively small size speaker as the center
speaker.
¢ WIDE — If you use a large size center speaker, choose this setting.
The full frequency range of the Dolby Surround center channel, from
low to high, is routed to the center speaker.
SPEAKER INSTALLATION
When not using a center speaker: DOLBY PRO LOGIC SURROUND
© PHANTOM — The signal which would have been sent to the center
speaker is divided equally between the left and right front speakers.
With DOLBY PRO LOGIC SURROUND, monaural source sound will be
heard only from the center channel at settings other than the PHANTOM
position.
To get the most out of the surround system, place the speakers as
shown below.
An example of speaker positioning
Front left Center speaker Front right
speaker FRONT speaker
Rear left Rear right
speaker speaker
SIMULATED STEREO
If the rear speakers are positioned at an extreme distance, the surround
level becomes unable to adjust and the surround effect will not be fully
achieved.
NOTE:
© To avoid interference with. the picture on a nearby TV set, use
magnetically shielded speaker systems. This is particularly important
for the center speaker since it is usually located closest to the TV.
© Position the left and right channel speakers at equal distances from
the TV set and approximately 1.8 m (6 feet) from each other.
Position the center speaker above, below, or behind the TV set. Sound
may not appear to coincide with the picture if you position it next to
the TV set.
© Rear speakers are best positioned slightly above ear level.
This function transforms monaural signals into simulated stereo sound.
Use it when you wish te experience a sense of stereo presence when
listening to AM broadcasts, and other monaural signal sources.
6
<ARB1421>
NOTE: ;
The simulated stereo function can also be used with stereo sound
sources, but it will result in an effect somewhat different from the normal
stereo sound.

CONNECTIONS
Setting Up the AM Antenna
© Insert the claw on the bottom of the antenna into the groove in
the leg.
© Place the antenna on a level surface and rotate it to locate the
orientation that yields the best reception.
¢ Use the attachment hole in the leg to screw to wall or other
location, then insert the claw on the bottom of the antenna into
the groove in the leg (fixing the antenna in the direction that gives
the best reception). ;
Lead wire
Lead wire
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the plug by tugging
the cord and never touch the power cord when your hands are wet as
this could cause a short circuit or electric shock. Do not place the unit,
a piece of furniture, etc., on the power cord, or pinch the cord. Never
make a knot in the cord or tie it with other cords. The power cords
should
be
routed
such
that
they
are
not
likely
to
be
stepped
on.
A
damaged
power
cord
can
cause
fire
or
give
you
an
electrical
shock.
Check
the
power
cord
once
in
a
while.
When
you
find
it
damaged,
ask
your nearest PIONEER authorized service center or your dealer for a
replacement.
Precaution
regarding
installation
position
of
cassette
deck.
If
the
cassette
deck
is
installed
in
the
@
positions
as
shown
in
the
drawing
below,
it
may
be
adversely
affected
during
playback.
If
possible,
it
is
better
to
install
it
in
the
@
position.
THE
S-VIDEO
CONNECTORS
(VSX-D702S
only)
When
using
a
VCR
1,
LD
and
TV
monitor
which
has
S-VIDEO
connectors,
they
can
be
connected
to
the
S-VIDEO
connectors.
For
the
operation
of
components
connected
to
S-VIDEO
connectors,
refer
to
the
instruction
manuals
of
the
corresponding
components.
NOTE:
In
this
unit,
the
S-VIDEO
connectors
(Y-C
separate)
and
the
regular
pin
jacks
are
independent,
so
any
signal
input
througha
pin
jack
must
be
output
from
the
pin
jack,
and
any
signal
input
through
an
S-VIDEO
connector
must
be
output
through
the
S-
WDEO
connector.
¢
The
S-VIDEO
connector
is
for
video
portion
only,
so
be
sure
also
to make audio connections.
How to use S-VIDEO connectors
eo 2
eo 2 S-VIDEO jack
S
Check the position of
the holes and insert.
iN
For
the
method
of
switching
the
TV
monitor
S-VIDEO
connector/
VIDEO
jack,
refer
to
the
TV
monitor's
instruction
manual.
S-VIDEO plug
7
<ARB1421>

CONNECTIONS
NOTE FOR FM T-TYPE ANTENNA
BASIC AUDIO SYSTEM CONNECTIONS Stretch the antenna out to its full length, and affix it to a wall, etc.
NOTE FOR AM LOOP ANTENNA
The antenna should be placed at a distance from the receiver, and should
not be allowed to touch metallic objects.
Avoid placing it near CD players, personal computers, television sets,
Accessory and other devices generating radio frequencies.
* Illustration shows VSX-D702S U.S. and Canadian model.
FM-T type antenna
0
Accessory AM 7
Loop
antenna
Turntable
CD player
VSX-B702S
[Power cord connection example]
Cassette deck 1/DAT
8
<ARB1421>

BASIC VIDEO SYSTEM CONNECTIONS
TV tuner
REC) (PLAY) |Say
A tS
B68
mi @®@ © 0
Za Fy FR R
tocanes fo)
ei BOSE
~ VIDEO AUDIO 3
OUT OUT
(>.
LG |
CONNECTIONS
* S (video) connection.
See page 7.
(VSX-D702S only)
®
’
y
Ly
RONT SPEAKERS.
R & 3/|
JES LD player
9
<ARB1421>

CONNECTIONS
SPEAKER CONNECTIONS
Center/Rear speaker cord ,
P a (I iw
connection
none
@ Push the lever down. ® Ar) Left Center Right
@ insert the cord. t
® Jia ff N
@ Pull the lever back. @ © © ©
Front speaker cord connection
[VSX-D602S]
@ Push the lever up (or down).
@®
Insert
the
cord.
©
io)
@
©
@OLIO
© Pull the lever back.
—B- ©
in)
4Q
ner
Bs"
©
(VSX-D702S] us
@ Loosen cap.
@ Insert wire.
@® Tighten cap.
VSX-D702S
NOTE:
Use front and rear speakers with
impedance between 8Q and 16Q. For
“1 ONLY” operation, center speaker
impedance should be between 8 Q
and 162. During “1 + Il" operation, it
Should be between 4Q and 16Q.
[VSX-D702S U.S. and Canadian
models only]
This unit's front speaker terminals accept
banana plugs.
Please refer to the plug’s manual for
instructions on use.
em
10
<ARB1421>

CONNECTIONS
¢ Connecting Two Center Speakers for Dual Center
(VSX-D702S only)
There are two terminals for center speaker on the main unit, so you
can connect two speakers. When you cannot install a speaker under
or behind your TV, installing speakers either side of the TV as a center
speaker is just as effective.
When the speaker selector switch is in the ‘I + II’’ position, be sure
to connect two speakers. If only one speaker is connected, there
will be no sound.
Both speaker systems should have impedance of from 4 0 to 16 Q.
4~160/
SPEAKER
4~160/ 1
co ee ven
e~160/
SPEAKER 7
B~I60/ 1 ONLY
HAUT-PARLEUR,
SPEAKER
SELECTOR
NOTE:
When connecting a super woofer system such as the Pioneer
S-W7000, connect it to the same speaker terminals (A or B) to which
the front speakers are connected. Connecting the front speakers
and super woofer system to terminals A and B respectively will result
in reduced volume from the front speakers.
Front (R) Super woofer Front (L)
11
<ARB1421>

CONNECTIONS
APPLICATIONS NOTE:
DOLBY PRO LOGIC SURROUND, PRO LOGIC THEATER and
DOLBY 3CH LOGIC will not operate correctly if the signal passes
through a graphic equalizer.
Additional Audio and Video Components
When using DOLBY PRO LOGIC SURROUND or DOLBY 3CH
LOGIC, turn off the TAPE 2 MONITOR button or set the graphic
Cassette deck 2 equalizer for flat response or to its “through” (or off) setting, if
CS you have one in use.
er When using a graphic equalizer
~ ‘ AY
SAL ! }
(@. sa
1
H@r@ll ! !
1 '
| | !
{
REC ! !
INPUT OUTPUT ‘
1 {
: !
\
' '
\
! From L and R To Land R ‘
! REC jacks PLAY jacks !
4
R BS
Y SPEAKERS:
[FRONT PANEL]
(REC) (PLAY)
VCR (for playback only), or
another component such as
a TV camera.
12
<ARB1421 >

|
CONNECTIONS
When used with another power amplifier Caution for use of AC OUTLETS:
Use
these
jacks
when
using
a
separate
amplifier
as
the
power
source
Components
which
have
electrical
power
consumption
greater
than
that
instead
of
this
unit,
and
listening
to
speakers
which
are
connected
to
indicated
on
the
rear
panel
of
this
unit
cannot
be
connected.
Please
take
the separate amplifier. necessary precaution.
LEFT CENTER RIGHT
Power
amplifier
Power
amplifier
POWER IN
VSX-D702S
13
<ARB1421>

CONNECTIONS
MULTI-ROOM CONNECTIONS
NOTE:
Be careful not to make the wrong connections
for CONTROL IN/OUT (black) and MULTI-
ROOM REMOTE IN (green).
[Set-up example]
Ss
AN
system
(including
VSX-D702S
other
components,
such
as
a
CD
player
or
or
VSX-D602S)
cassette
deck,
bearing
the
fj
mark,
you
can
also
enjoy
remote
control
of
these
7 ~
Xe components from Sub Room. (For details
concerning connections, refer to page 16.)
4 Speakers A
4
is an If you connect to the CONTROL jacks of
4
SU
Speakers A
eee
*\Ilustration shows VSX-D702S U.S. and
Canadian models.
Main Room Sub Room
Speaker (L) TV monitor Speaker (R) Speaker (L) Speaker (R)
A 2 Multi ti
ulti-room remote sensor
~ SS unit MR-100
Black ~S,
14
<ARB1421>

REAR PANEL FACILITIES
* Illustration shows VSX-D702S U.S. and Canadian models.
@ @ @
Looe
ANTENNA
O® ©
@ FM/AM ANTENNA terminals
Use these antenna terminals for reception of normal FM and AM
broadcasts.
@ TAPE 2 MONITOR jacks
Connect the second cassette deck to these jacks.
Connecting for Recording
The tape recording jack (REC) on the cassette deck should be connected
to the REC side of the TAPE 2 MONITOR jack on the receiver with a
pin plug connecting cord.
Connecting for Playback
Connect the TAPE PLAY jack on the cassette deck to the PLAY side
of the TAPE 2 MONITOR jack on the receiver with a pin plug connecting
cord.
@ TAPE 1/DAT jacks
Use these to connect the cassette deck or DAT (digital audio tape) deck.
Connecting for Recording
The tape recording jack (REC) on the cassette deck or DAT should be
connected to the REC side of the TAPE 1/DAT jack on the receiver with
a pin plug connecting cord.
Connecting for Playback
Connect the PLAY jack on the cassette deck or DAT to the PLAY side
of the TAPE 1/DAT jack on the receiver with a pin plug connecting cord.
@ VCR 2 jacks
[VIDEO OUT]
When copying program material from the video component
connected to the VCR 1, TV, VIDEO (front) or LD jacks, connect to the
VIDEO INPUT jacks of the VCR used for recording.
[AUDIO OUT (L, R)]
When copying program materials from the video component
connected to the VCR 1, TV, VIDEO (front) or LD jacks, or when
recording music from an audio component source, connect to the
AUDIO INPUT jacks of the VCR used for recording.
UT:
©
Roe
SPEAKERS.
® © ®©O® ® @
[VIDEO IN]
When monitoring the video image from a VCR used for copying,
connect its VIDEO OUTPUT jacks here.
[AUDIO IN (L, R)]
When monitoring the audio channel from a VCR used for copying,
connect its AUDIO OUTPUT jacks here.
® VIDEO OUT (TV MONITOR) jack
Connect to monitor TV or to TV sets with video input terminals fer
watching program materials from a VCR 1, 2, TV, VIDEO (front) or LD
player connected to this unit.
© VCR 1 jacks
[VIDEO OUT]
When copying program material from the video component
connected to the VCR 2, TV, VIDEO (front) or LD jacks, connect to the
VIDEO INPUT jacks of the VCR used for recording.
[AUDIO OUT (L, R)]
When copying program material from the video component
connected to the VCR 2, TV, VIDEO (front) or LD jacks, or when
recording music from an audio component source, connect to the
AUDIO INPUT jacks of the VCR used for recording.
[VIDEO IN]
When monitoring the video image from a VCR used for playing,
connect its VIDEO OUTPUT jacks here.
[AUDIO IN (L, R)]
When monitoring the audio channel from a VCR used for playing,
connect its AUDIO OUTPUT jacks here.
15
<ARB1421>

REAR PANEL FACILITIES
@ PRE OUT jacks
[FRONT AMP]
When a separate power amplifier is used to drive the front speakers,
connect the power amplifier to these jacks.
{CENTER AMP]
When a separate power amplifier is used to drive the surround center
speaker, connect the power amplifier to this jack.
[REAR AMP]
When a separate power amplifier is used to drive the rear speakers,
connect the power amplifier to these jacks.
@ CENTER SPEAKER terminals
Connect the center speaker to these terminals.
The VSX-D702S has two sets of center speaker terminals so dual center
speakers can be used. (See page 11)
NOTE:
Do not allow any of the cord’s conductors to protrude from the terminals
or touch any other conductors. Malfunctioning or breakdowns may
occur when conductors come into contact with each other.
@REAR SPEAKERS terminals
Connect the rear speakers to these terminals.
NOTE:
Do not allow any of the cord’s conductors to protrude from the terminals
or touch any other conductors. Malfunctioning or breakdowns may
occur when conductors come into contact with each other.
Use rear speakers of impedance 8 2 — 16 2.
FRONT SPEAKERS terminals
A: Connect to the first set of speakers.
B: Connect to the second set of speakers.
Speaker lead wire preparation and connection.
NOTE:
Do not allow any of the cord’s conductors to protrude from the terminals
or touch any other conductors. Malfunctioning or breakdowns may
occur when conductors come into contact with each other.
Use speakers of impedance 8 2 — 16 0.
@ PHONO input jacks
Connect to the output cables from a turntable.
@2 GND terminal
Connect the turntable ground lead to this terminal.
@ CD input jacks
Connect to the output jacks of a compact disc player.
TV jacks (input)
Use these jacks if you wish to connect a TV tuner with both video and
audio outputs.
[VIDEO IN]
Connect the TV tuner’s VIDEO OUTPUT to this jack.
[AUDIO IN (L, R)]
Connect the TV tuner’s AUDIO OUTPUT to these jacks.
@) LD jacks
[VIDEO IN]
When watching the video image from an LD player, connect its VIDEO
OUTPUT jacks here.
[AUDIO IN (L, R)]
When playing back the audio channel from an LD player, connect its
AUDIO OUTPUT jacks here.
16
<ARB1421>
@ $ (connector) video jacks (VSX-D702S only)
When used in conjunction with a VCR, Video disc player (LaserDisc
player), or TV monitor equipped with S video jacks, connect to these
jacks. (See pages 7, 9)
@ CENTER SPEAKER SELECTOR Switch
This switch changes the speaker impedance for when only one center
speaker is connected, or two speakers are connected.
When only one speaker is'connected:
Be sure to set the switch to “I ONLY’’ (down side), and always connect
a speaker with an impedance of 8 2 — 16 © to the | terminal.
When two speakers are connected:
Be sure to set the switch to “I + II’’ (up side), and always use speakers
with an impedance of 42 — 16 Q.
NOTE:
Switch the CENTER SPEAKER SELECTOR when the unit power
supply is at STANDBY. Do not switch the selector when the power
supply is at ON.
CONTROL IN/OUT jacks
IN: Connect this jack to other Pioneer components (main unit or
remote contro! unit) when using those components to control
this unit.
OUT: Connect this jack to other Pioneer components when using the
remote control of this unit.to control the other components.
NOTE:
The receiver's remote sensor does not function when a plug is inserted
in INjack. To operate, point the remote control unit at the remote sensor
on the component to which the receiver's IN jack is connected.
When using 1) conven
the MR-100 mel Je
MR-100 Cl ex
ZVese Receiver f—
Pioneer component
bearing the {i mark.
Remote
control To the CONTROL IN
MEME
Remote
jack
of
the
Pioneer
control unit component bearing
the fi] mark.

REAR PANEL FACILITIES
a
acid
MULTI-ROOM REMOTE IN jack
Connect
to
the
separately
sold
MR-100
Multi-Room
remote
control
unit.
AC OUTLETS
{U.S. and Canadian models]
[SWITCHED TOTAL 100 W (0.8 A) MAX]
Power
supplied
through
these
outlets
is
turned
on
and
off
by
the
receiver's
POWER
switch.
Total
electrical
power
consumption
of
connected
equipment
should
not
exceed
100
W
(0.8
A).
[UNSWITCHED 100 W (0.8 A) MAX]
Power
flows
continually
to
this
outlet,
regardless
of
whether
tne
receiver
is
switched
ON
or
OFF.
Electrical
power
consumption
of
the
connected
equipment should not exceed 100 W (0.8 A).
The
equipment
should
be
disconnected
by
removing
the
power
plug
from
the
wall
socket
when
not
in
regular
use,
@.g.
when
on
vacation.
[Multi-voltage model]
SWITCHED TOTAL 100 W MAX
Power
supplied
through
these
outlets
is
turned
on
and
off
by
the
receiver's
POWER
switch.
Total
electrical
power
consumption
of
connected
equipment
should
not
exceed
100
W.
UNSWITCHED 100 W MAX
Power
flows
continually
to
this
outlet,
regardless
of
whether
the
receiver
is
switched
ON
or
OFF.
Electrical
power
consumption
of
the
connected
equipment
should
not
exceed
100
W.
NOTE:
m1
©
This
unit
should
be
disconnected
by
removing
the
power
plug
from
the
wall
socket
when
not
in
regular
use,
e.g.
when
on
vacation.
©
Do
not
connect
appliances
with
high
power
consumption
such
as
heaters,
irons,
or
television
sets
to
these
AC
OUTLETS
in
order
to
avoid overheating and fire risk.
This can cause the receiver to malfunction.
CAUTION:
DO NOT CONNECT MONITOR OR TV SET.
@) Power cord
17
<ARB1421>

FRONT PANEL FACILITIES
* Illustration shows model VSX-D702S.
QO @®
@ POWER STANDBY/ON switch/STANDBY indicator
This is the switch for electric power.
ON: When set to the ON position, power is supplied and the
unit becomes operational.
STANDBY: When set to STANDBY position, the main power flow is
cut and the unit is no longer fully operational. A minute
flow of power feeds the unit to maintain operation
readiness.
The STANDBY indicator lights when the power is
STANDBY, and goes out during ON.
[Timer ON/OFF possible]
When the unit is switched ON, ON/OFF control can be performed by
means of the optional timer.
NOTE:
When the power is initially tumed ON, muting will be applied to prevent
sound from being output for about 5 seconds.
@V-SIGNAL (VIDEO SIGNAL) SELECTOR button
Use to change the video signal in sequence leaving the sound
unchanged.
aes 4— VCR 2—+ LD— TV—+ VIDEO — OFF sae
The current setting is shown by an indicator on the display section.
18
<ARB1421>
®@®@OOODHO® ®
©®H ®80©60©0O0 ®
@ [t @ @
@) Remote sensor
@ AUTO SOURCE CONTROL/MEMORY buttons
(See page 29)
1, 2 buttons:
These buttons are for memorizing and recalling your current settings.
Both 1 and 2 can be used to memorize settings. If you connect another
component, such as a CD player, to the CONTROL OUT jack on the
rear panel, the signals to switch power on and start play are also
transmitted.
MEMORY:
Use when memorizing settings to a 1, 2 button.
©) MEMORY button (See page 23)
Pressing this button will result in the memorization of the current
broadcast band, reception frequency, and MPX AUTO/MONO mode.
This button is also used for custom memory operation.
© CUSTOM MEMO SEL button (See page 23)
Recall a genre name with this button.

FRONT PANEL FACILITIES
@ SCAN button
Operate when the INPUT SELECTOR is set to TUNER. Station
frequencies assigned to the STATION CALL buttons are tuned in, one
after another, beginning with the current station no., for approximately
5 seconds each. The display section SCAN indicator will light. Press
the button again and the tuner remains tuned in to the station playing
when the button was pressed the second time.
Station frequencies not assigned to station numbers in the memory are.
skipped.
When you have selected a CUSTOM MEMORY genre, memory scan
is performed on the stations in that genre.
(8) MPX MODE button
Use to select the auto stereo mode or monaural mode when listening
to FM broadcasts. The monaural mode has been selected when the
FM MONDO indicator in the display section is lit. ©
Auto stereo mode:
Normally, leave in this mode for reception. When a stereo FM broadcast
is received, it will be automatically reproduced in stereo.
Monaural mode: :
When receiving distant stations or stations with weak broadcast signals,
the input signal may be weak, thus resulting in increased noise during
FM stereo broadcasts. In this event, setting the receiver to the monaural
mode will reduce the noise. In this case, however, FM stereo broadcasts
will be reproduced in monaural sound.
NOTE:
This button has no effect on reception of AM broadcasts.
@) Tuning buttons
TUNING MODE tuning selector button: (Pages 22, 23)
Use to select the tuning mode. To select the AUTO tuning mode, press
this button to light the AUTO TUNING indicator in the display section.
To select the MANUAL tuning mode, switch off the AUTO TUNING
indicator.
AUTO tuning
When the — or + TUNING button is pressed, the receiver automatically
_ scans the broadcast station frequencies. When a broadcast is detected,
the.scanning stops at that frequency.
NOTE:
Pressing the TUNING button (— or +} while scanning is taking place
causes scanning to stop.
MANUAL tuning
This lets you manually tune to particular broadcast frequencies. Each
press of the + or — button raises or lowers the frequency by one tuning
step. For continuous scanning, keep the button pressed, then release
it to stop scanning.
DIRECT ACCESS tuning button: (Page 22)
When this button is pressed, the STATION CALL buttons function as
ten-key number buttons for direct input of the desired reception
frequency. Press again to cancel this mode.
If the input station falls outside of the receiver's tuning range, the display
section will display a message: ‘“UPPER”’ if the frequency is too high
and “LOWER” if it is too low. :
HITS (Hyper Intelligent Tuning System) button: (Page 24)
Press this button, and search automatically begins up and down the
frequency for stations that can be received. When a station that can
be received is found, the search operation stops.
@ STATION CALL buttons
Up to 30 FM or AM stations can be preset at random.
These buttons are used to preset ‘and recali desired broadcasting
stations, FM AUTO/MONO mode.
NOTE: :
Pressing a STATION CALL button will select TUNER as the source,
regardless of what other listening source or function was selected.
They are also used when performing direct access tuning.
@) SIMULATED STEREO button
Press to produce a simulated stereo effect when listening to monaural
sources (for example, normal AM or TV broadcasts).
“SIMULATED STEREO” appears on the display section.
NOTE:
© This effect is not produced through the rear speakers.
* Use with the SURROUND MODE in the OFF.
@ SURROUND MODE selector buttons
See page 5 “SURROUND EFFECT’.
@ BALANCE buttons
Use them to adjust the sound volume balance between left and right
speakers.
L: Press to decrease the sound on the right side.
R: Press to decrease the sound on thé left side.
Press L and R together to bring the volume balance back to center.
NOTE:
The left-right sound volume balance cannot be adjusted on the rear
speakers.
@ TREBLE control buttons
Use to adjust the high-frequency level. Press the + button to increase
the high-frequency level, and the — button to decrease it.
The TONE indicator appears on the display section.
When both buttons (—, +) of the TREBLE control are pressed
simultaneously, the treble response will be set to the flat (normal)
condition.
@ BASS control buttons
Use to adjust the low-frequency level. Press the + button to increase
the low-frequency level, and the — button to decrease it.
The TONE indicator appears on the display section.
When both buttons (—, +) of the BASS control are pressed
simultaneously, the bass response will be set to the flat (normal)
condition.
DSP EFFECT/DELAY TIME buttons
[DSP EFFECT)
When using a surround mode other than DOLBY PRO LOGIC
SURROUND, 10-step adjustment of the effect level is possible from
10 to 100.
{DELAY TIME]
Operates when the DOLBY PRO LOGIC SURROUND mode is ON.
Switches to surround delay time in 8 steps. For DOLBY PRO LOGIC
SURROUND, 20 ms is standard.
Changes in 2 ms steps.
16 ms +> 18 ms <+--- ++28 ms ++30 ms
19
<ARB1421>

FRONT PANEL FACILITIES
@) DOLBY 3CH LOGIC button
Select this setting when stereo-source regeneration and rear speak-
ers are not connected and you wish to use the front L, front R,
and center speakers to enjoy audio/visual material bearing the
DIC [pow sunnouND] mark
MASTER VOLUME control
Use it to simultaneously adjust the sound volume from the front, center
and rear speakers.
PHONES jack
Connect the plug on your headphones to this jack. Set all SPEAKERS
A and B switches to OFF if you want to cut the sound from speakers
and listen to it only through the headphones.
@ SPEAKERS buttons (A, B) & OFF = ON
ON/OFF switches for the A and B speaker systems.
NOTE: :
No sound will be heard thorough the speakers when both A and B
buttons are depressed if only one set of speakers has been connected
to either A or B SPEAKERS terminals.
@) BAND (FM/AM) button
Use this to switch between FM and AM frequency band reception.
@ TUNING buttons
+: Performs tuning from the currently displayed station frequency in
ascending frequency order.
- : Performs tuning in order of descending frequencies.
@ INPUT SELECTOR buttons
VCR 1: Press when performing playback on a first VCR unit.
VCR 2: Press when performing playback on a second VCR unit.
LD: Press when performing playback on an LD player.
TV: Press when using a TV tuner connected to the TV jacks.
VIDEO: Press when performing playback on a VCR connected to
VIDEO INPUT jacks on the front panel.
TAPE 1/DAT:
Press when performing playback on a DAT or cassette deck. :
TAPE 2 MONITOR:
Press when performing playback on a second cassette deck
or second DAT and when monitoring recording.
CD: Press when playing compact discs on a CD player.
TUNER: Press when listening to radio broadcasts.
PHONO: Press when playing records on turntable.
20
<ARB1421>
@) ACOUSTIC buttons (See page 28)
MEMORY: :
Pressing this button will result in the memorization of the sound quality
{tone control condition). Press again to cancel this mode.
SELECT:
¢ This button is used to preset the five acoustic memories (A—E).
* This button is also used to recall previously set sound quality settings.
Each time you press the. button, the sound quality setting advances
in the order shown below.
peers ee er ee oe
FLAT: For flat (normal) frequency response.
LOUDNESS: Emphasizes the low- and high- frequency ranges.
Produces a fuller sense of sound, particularly when
listening at low volume. :
A-E: Memorized acoustic memory settings.
@ RESET button
Use this when normal operation becomes impossible because of external
influences such as static electricity or lightning, or when operation is
impossible even when operation buttons are pressed. Press this button
to return to normal operating conditions.
if you press this button when the power is ON, the unit switches to
POWER STANDBY, and the entire Contents of the memory are erased.
@) RETURN button
Press this button to return the receiver into the initial state. TUNER is
selected at this initial state. Adjust the sound level by using the MASTER
VOLUME control.
© TAPE 2 MONITOR ....... OFF e FUNCTION.............. TUNER
e SURROUND MODE....... OFF =e V-SIGNAL SELECTOR.... OFF
© MUTING ..... ee eeeeeees OFF = ® TONE... .ccccesecseerenevevens flat
¢ BALANCE ............. CENTER
The HITS function searches for broadcast stations among the
frequencies displayed.
NOTE:
If no sound is output after the RETURN button is pressed, make sure
that SPEAKERS buttons are turned on.
@ MUTING button
Press to temporarily cut off the sound volume. When pressed again,
the sound will return to its previous level.
VIDEO INPUT jacks
VIDEO components such as a VCR or TV camera, etc. can be
connected.