Sony STR-DG500 - Multi Channel Av Receiver User manual

1
SERVICE MANUAL
US Model
Canadian Model
STR-DG500/DG600
AEP Model
UK Model
E Model
Australian Model
STR-DG500
STR-DG500/DG600
MULTI CHANNEL AV RECEIVER
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(Models of area code US only)
With 8 ohm loads, both channels driven, from
20 – 20,000 Hz; rated 100 watts per channel
minimum RMS power, with no more than
0.09 % total harmonic distortion from 250
milliwatts to rated output.
Amplifier section
Power Output
Models of area code US, CND
Stereo Power Output1), Reference Power Output1) 2)
8 ohms 20 Hz – 20 kHz, THD 0.09 %
100 W + 100 W, 110 W/ch
8 ohms 1 kHz, THD 0.7 % 110 W + 110 W, 120 W/ch
8 ohms 1 kHz, THD 10 % 125 W + 125 W, 150 W/ch
Models of area code AEP, UK, E2, TW, AUS
Stereo Power Output1), Reference Power Output1) 2)
8 ohms 20 Hz – 20 kHz, THD 0.09 %
85 W + 85W, 110 W/ch
8 ohms 1 kHz, THD 0.7 % 100 W + 100 W, 120 W/ch
8 ohms 1 kHz, THD 10 % 125 W + 125 W, 150 W/ch
SPECIFICATIONS
Models of area code KR
Stereo Power Output1), Reference Power Output 1) 2)
8 ohms 20 Hz – 20 kHz, THD 0.09 %
85 W + 85 W1),
70 W + 70 W3), 110 W/ch
8 ohms 1 kHz, THD 0.7 % 100 W + 100 W 1),
90 W + 90 W3), 120 W/ch
8 ohms 1 kHz, THD 10 % 125 W + 125 W 1),
110 W + 110 W 3), 150 W/ch
1) Measured under the following conditions:
Area code Power requirements
US, CND 120 V AC, 60 Hz
AEP, UK, KR 230 V AC, 50 Hz
E2, AUS 240 V AC, 50 Hz
TW 110 V AC, 60 Hz
2) Reference power output for front, center, surround
and surround back. Depending on the sound field
settings and the source, there may be no sound output.
3) Measured under the following conditions:
Area code Power requirements
KR 220 V AC, 50 Hz
Ver. 1.0 2006. 02
9-887-127-01
2006B04-1
© 2006. 02
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, “Surround EX”, and the double-D
symbol are trademarks of Dolby Laboratories.
“DTS”, “DTS-ES”, “Neo:6”, and “DTS 96/24” are
trademarks of Digital Theater Systems, Inc.
– Continued on next page –
Photo: STR-DG600: Silver type
All manuals and user guides at all-guides.com
all-guides.com

2
STR-DG500/DG600
Frequency response
Analog 10 Hz – 70 kHz
+0.5/–2 dB (with sound
field and tone (DG500) or
equalizer (DG600) bypassed)
Inputs
Analog Sensitivity: 500 mV/
50 kohms
S/N 4) : 96 dB
(A, 500 mV 5) )
Digital (Coaxial) Impedance: 75 ohms
S/N: 100 dB
(A, 20 kHz LPF)
Digital (Optical) S/N: 100 dB
(A, 20 kHz LPF)
Output (Analog)
AUDIO OUT Voltage: 500 mV/10 kohms
SUB WOOFER, SURROUND (DG600)
Voltage: 2 V/1 kohm
Tone (DG500), EQUALIZER (DG600)
Gain levels ±6 dB, 1 dB step
4) INPUT SHORT (with sound field and tone (DG500) or
equalizer (DG600) bypassed).
5) Weighted network, input level.
FM tuner section
Tuning range 87.5 – 108.0 MHz
Intermediate frequency 10.7 MHz
Useable sensitivity 11.2 dBf, 1 µV/75 ohms
S/N
Mono/Stereo 76 dB/70 dB
Harmonic distortion at 1 kHz
Mono/Stereo 0.3%/0.5%
Separation 45 dB at 1 kHz
Frequency response 30 Hz – 15 kHz,
+0.5/–2 dB
AM tuner section
Tuning range
Models of area code US, CND
With 10-kHz tuning scale: 530 – 1,710 kHz6)
With 9-kHz tuning scale: 531 – 1,710 kHz 6)
Models of area code E2
With 10-kHz tuning scale: 530 – 1,610 kHz6)
With 9-kHz tuning scale: 531 – 1,602 kHz 6)
Models of area code AEP, UK, AUS, TW, KR
With 9-kHz tuning scale: 531 – 1,602 kHz
Intermediate frequency 450 kHz
Usable sensitivity 50 dB/m (at 1,000 kHz or
999 kHz)
6) You can change the AM tuning scale to 9 kHz or 10 kHz.
After tuning in anyAM station, turn off the receiver. While
holding down TUNING MODE, press ?/1. All preset
stations will be erased when you change the tuning scale.
To reset the scale to 10 kHz (or 9 kHz), repeat the
procedure.
Video section
Inputs/Outputs
Video: 1 Vp-p, 75 ohms
S-video (DG600): Y: 1 Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms
COMPONENT VIDEO: Y: 1 Vp-p, 75 ohms
PB/CB/B-Y: 0.7 Vp-p/
75 ohms
PR/CR/R-Y: 0.7 Vp-p/
75 ohms
80 MHz HD Pass Through
General
Power requirements
Area code Power requirements
US, CND 120 V AC, 60 Hz
AEP, UK 230 V AC, 50/60 Hz
AUS 240 V AC, 50 Hz
KR 220 – 230 V AC, 50/60 Hz
E2 120/220/240 V AC, 50/60 Hz
TW 110 V AC, 50/60 Hz
Power consumption
Area code Power consumption
DG500: US, AEP, UK, 220 W
AUS, KR, E2
DG500: CND 300 VA
TW 500 W
DG600: US 230 W
DG600: CND 310 VA
Power consumption (during standby mode)
0.2 W
AC outlets (DG600)
Area code AC outlets
US, CND 1 switched, 120 W/1A MAX
Dimensions (w/h/d) (Approx.)430 ×157.5 ×316 mm
(16 7/8 ×6 2/8 ×12 4/8
inches) including
projecting parts and
controls
Mass (Approx.) 8.0 kg (17 lb 11 oz)
Supplied accessories
FM wire antenna (1)
AM loop antenna (1)
Remote commander RM-AAU005 (1) (DG500)
Remote commander RM-AAP012 (1) (DG600)
R6 (size-AA) batteries (2)
Optimizer microphone ECM-AC2 (1)
Design and specifications are subject to change
without notice.
•Abbreviation
CND : Canadian model
E2 : 120 V AC area in E model
TW : Taiwan model
AUS:Australian model
KR : Korea model
All manuals and user guides at all-guides.com

3
STR-DG500/DG600
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LASÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
1.5 k Ω 0.15 µFAC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
SAFETY CHECK-OUT (US MODEL)
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Checkthe antennaterminals, metal trim,“metallized” knobs,screws,
and all other exposed metal parts forAC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-
amples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2 VAC range are suit-
able. (See Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
MODEL IDENTIFICATION
— BACK PANEL —
Part No.
MODEL PART No.
DG500: US 2-661-146-0s
DG500: CND 2-661-146-1s
DG500: AEP, UK 2-661-146-2s
DG500: AUS 2-661-146-4s
DG500: TW 2-661-146-5s
DG500: KR 2-661-146-6s
DG500: E2 2-661-146-7s
DG600: US 2-661-147-0s
DG600: CND 2-661-147-1s
•Abbreviation
CND: Canadian model
AUS:Australian model
TW : Taiwan model
KR : Korea model
E2 : 120 VAC area in E model
All manuals and user guides at all-guides.com

4
STR-DG500/DG600
TABLE OF CONTENTS
1. GENERAL
Description and location of parts (STR-DG500) .................... 5
Description and location of parts (STR-DG600) .................... 7
2. DISASSEMBLY
2-1. Case ................................................................................... 10
2-2. Front Panel Section ........................................................... 11
2-3. Back Panel Section............................................................ 11
2-4. DIGITAL Board ................................................................ 12
2-5. MAIN Board Section ........................................................ 12
2-6. STANDBY Board ............................................................. 13
2-7. SBAMP Board (DG600) .................................................. 13
3. TEST MODE ..................................................................... 14
4. DIAGRAMS
4-1. Block Diagram – Tuner/Audio Section –.......................... 15
4-2. Block Diagram – Digital Section – ................................... 16
4-3. Block Diagram – Video Section – .....................................17
4-4. Block Diagram – XM Section (DG600) – ........................ 18
4-5. Block Diagram – Key/Display Section – .......................... 19
4-6. Block Diagram – Power Section – .................................... 20
4-7. Circuit Boards Location .................................................... 21
4-8. Printed Wiring Boards – Main Section – .......................... 22
4-9. Schematic Diagram – Main Section (1/3) – ...................... 23
4-10. Schematic Diagram – Main Section (2/3) – ...................... 24
4-11. Schematic Diagram – Main Section (3/3) – ...................... 25
4-12. Printed Wiring Board – Digital Section (1/2) – ................ 26
4-13. Printed Wiring Board – Digital Section (2/2) – ................ 27
4-14. Schematic Diagram – Digital Section (1/5) – ................... 28
4-15. Schematic Diagram – Digital Section (2/5) – ................... 29
4-16. Schematic Diagram – Digital Section (3/5) – ................... 30
4-17. Schematic Diagram – Digital Section (4/5) – ................... 31
4-18. Schematic Diagram – Digital Section (5/5) – ................... 32
4-19. Printed Wiring Boards
– Center/Surround Back Speaker Section – ...................... 33
4-20. Schematic Diagram
– Center/Surround Back Speaker Section – ...................... 34
4-21. Printed Wiring Board – Front B Speaker Section – .......... 35
4-22. Schematic Diagram – Front B Speaker Section – ............. 35
4-23. Printed Wiring Board – Video Section – ........................... 36
4-24. Schematic Diagram – Video Section –.............................. 37
4-25. Printed Wiring Board – S-video Section – ........................ 38
4-26. Schematic Diagram – S-video Section –........................... 38
4-27. Printed Wiring Board
– S-video Up Convert Section (DG600) – ........................ 39
4-28. Schematic Diagram
– S-video Up Convert Section (DG600) – ........................ 39
4-29. Printed Wiring Board – XM Section (DG600) – .............. 40
4-30. Schematic Diagram – XM Section (DG600) – ................. 41
4-31. Printed Wiring Board – ADCC Section – ......................... 42
4-32. Schematic Diagram – ADCC Section – ............................ 42
4-33. Printed Wiring Boards – Display Section – ...................... 43
4-34. Schematic Diagram – Display Section –........................... 44
4-35. Printed Wiring Boards – Power Section –......................... 45
4-36. Schematic Diagram – Power Section – ............................. 46
5. EXPLODED VIEWS
5-1. Case Section ...................................................................... 58
5-2. Front Panel Section ........................................................... 59
5-3. Back Panel Section............................................................ 60
5-4. Chassis Section ................................................................. 61
6. ELECTRICAL PARTS LIST ........................................ 62
All manuals and user guides at all-guides.com

5
STR-DG500/DG600
SECTION 1
GENERAL This section is extracted
from instruction manual.
5
GB
Getting Started
Description and location of parts
To remove the cover
Press PUSH.
When you remove the cover, keep it out of
reach from children.
Getting Started
Front panel
?/1
AUTO CAL MIC
SPEAKERS
(OFF/A/B /A+B)
PHONES VIDEO 3 IN/PORTABLE AV IN
VIDEO L AUDIO R
MEMORY/
ENTER TUNING MODE TUNING 2CH A.F.D. MOVIE MUSIC
MULTI CH IN DIRECT
DISPLAY
MULTI CHANNEL DECODING
INPUT MODE
INPUT SELECTOR
MASTERVOLUME
1 3246 875
9q;w; qaqsqkql qdqfqgqhqj
PUSH
Name Function
A?/1Press to turn the receiver
on or off (page 25, 32, 33,
53, 55, 73).
BSPEAKERS
(OFF/A/B/A+B) Press to select OFF, A, B, A+B of the front speakers
(page 26).
CDisplay The current status of the
selected component or a
list of selectable items
appears here (page 7).
DMULTICHANNEL
DECODING lamp Lights up when multi channel audio is decoded
(page 33).
ERemote sensor Receives signals from
remote commander.
continued
6
GB
Name Function
FDISPLAY Presstoselectinformation
displayed on the display
(page 59, 62).
GINPUT MODE Press to select the input
mode when the same
components are connected
to both digital and analog
jacks (page 60).
HMASTER
VOLUME Turn to adjust the volume level of all speakers at the
same time (page 30, 31,
32, 33).
IDIRECT Press to listen to high
quality analog sound
(page 52).
JMULTI CH IN Press to select the audio
directly from the
components connected to
the MULTI CH IN jacks
(page 31).
KINPUT
SELECTOR Turn to select the input source to playback (page
31, 32, 33, 52, 54, 57, 58,
60, 62, 63, 64).
LMOVIE,
MUSIC Pressto select sound fields (MOVIE, MUSIC) (page
49).
MA.F.D. Press to select A.F.D.
mode (page 47).
N2CH Press to select 2CH
STEREO mode (page 52,
53).
OTUNING +/– Press to scan a station
(page 54, 57).
PTUNING MODE Press to select the tuning
mode (page 54, 57, 73).
QMEMORY/ENTER Press to store a station or
enter the selection when
selecting the settings
(page 25, 56).
Name Function
RVIDEO 3 IN/
PORTABLE AV IN
jacks
To connect a camcorder or
video game (page 23, 31).
SAUTO CAL MIC
jack Connects to the supplied ECM-AC2 optimizer
microphone for the Auto
Calibration function (page
27).
TPHONES jack Connects to a headphone
(page 68).
7
GB
Getting Started
About the indicators on the display
MEMORY
L C R
SL S SR
SB
SW
LFE
SP A
SP B
RDS
STEREO MONO A.DIRECT D.RANGE
NEO:6
SLEEP OPT COAX 96/24
DIGITAL EX ; DTS-ES ;
PRO LOGIC IIx
qs qa
qg
qh
qdqf
214356789
q;
Name Function
ASW Lights up when sub woofer
selection is set to “YES” (page
37) and the audio signal is
output from the SUB WOOFER
jack.
BLFE Lights up when the disc being
played back contains an LFE
(Low Frequency Effect)
channel and the LFE channel
signal is actually being
reproduced.
CSP A/SP B Lights up according to the
speaker system used. However,
these indicators do not light up
if the speaker output is turned
off or if a headphone is
connected.
D;DIGITAL
(EX) Lights up when Dolby Digital signals are input. “;
DIGITAL EX” lights up when
Dolby Digital Surround EX
signals are decoded.
Note
When playing a Dolby Digital
format disc, be sure that you
have made digital connections
and that INPUT MODE is not
set to “ANALOG” (page 60).
E;PRO
LOGIC (II)/
(IIx)
Lights up when the receiver
applies Pro Logic processing to
2 channel signals in order to
output the center and surround
channel signals. “; PRO
LOGIC II” lights up when the
Pro Logic II Movie/Music/
Game decoder is activated.
“; PRO LOGIC IIx” lights up
when the Pro Logic IIx Movie/
Music/Game decoder is
activated. However, these
indicators do not light up if both
the center and surround
speakers are set to “NO” (page
37) and you select a sound field
using the A.F.D. button.
Note
Dolby Pro Logic IIx decoding
does not function for DTS
format signals or for signals
with a sampling frequency of
more than 48 kHz.
FDTS (-ES)/
(96/24) Lights up when DTS signals are input. “DTS-ES” lights up
when DTS-ES signals are input.
“DTS96/24”lightsup when the
receiver is decoding DTS 96
kHz/24 bit signals.
Note
When playing a DTS format
disc,be surethat you havemade
digital connections and that
INPUT MODE is not set to
“ANALOG” (page 60).
GNEO:6 Lights up when DTS Neo:6
Cinema/Music decoder is
activated (page 48).
Name Function
continued
8
GB
HMEMORY Lights up when a memory
function, such as Preset
Memory (page 57), etc., is
activated.
IA.DIRECT Lights up when ANALOG
DIRECT is selected (page 52).
JPreset
station
indicators
Lights up when using the
receiver to tune in radio stations
you have preset. For details on
presetting radio stations, see
page 56.
KTuner
indicators Lights up when using the receiver to tune in radio stations
(page 53), etc.
Note
“RDS” appears for models of
area code CEL, CEK only.
LD.RANGE Lights up when dynamic range
compression is activated (page
35).
MCOAX Lights up when INPUT MODE
is set to “AUTO” and the source
signal is a digital signal being
input through the COAXIAL
jack, or when INPUT MODE is
set to “COAX IN” (page 60).
NOPT Lights up when INPUT MODE
is set to “AUTO” and the source
signal is a digital signal being
input through the OPTICAL
jack, or when INPUT MODE is
set to “OPT IN” (page 60).
OSLEEP Lights up when the sleep timer
is activated (page 63).
Name Function
PPlayback
channel
indicators
L
R
C
SL
SR
S
SB
The letters (L, C, R, etc.)
indicate the channels being
played back. The boxes around
the letters vary to show how the
receiver downmixes the source
sound (based on the speaker
settings).
Front Left
Front Right
Center (monaural)
Surround Left
Surround Right
Surround (monaural or the
surround components obtained
by Pro Logic processing)
Surround back (the surround
back components obtained by
6.1 channel decoding)
Example:
Recording format (Front/
Surround): 3/2.1
Outputchannel: When surround
speaker is set to “NO” (page 37)
Sound Field: A.F.D. AUTO
Name Function
L C R
SL SR
SW
STR-DG500:
All manuals and user guides at all-guides.com

6
STR-DG500/DG600
9
GB
Getting Started
Rear panel
12
DIGITAL
OPTICAL
VIDEO 1
IN
VIDEO 2
IN
DVD
IN
COAXIAL
AM
ANTENNA
VIDEO 1 MULTI CH IN
FRONT
CENTER
SUB
WOOFER
SURROUND
VIDEO IN
AUDIO IN
AUDIO
OUT
VIDEO IN VIDEO OUT
VIDEO 2
AUDIO IN
MD/TAPE SA-CD / CD
L
R
L
R
L
RSUB
WOOFER
LL
RR
OUT ININ
VIDEO IN
DVD
AUDIO IN AUDIO OUT
VIDEO OUT
DVD
IN VIDEO 2 IN MONITOR OUT
COMPONENTVIDEO
Y
ASSIGNABLE
P B /C B
/BñY
P
R /C R
/RñY
MONITOR
CENTER
SURROUND BACK
SURROUND FRONT A
R
R
L
L
+ – + –
SPEAKERS
+
–
5 6
SPEAKERS
FRONT B
LR
LR
3
4
ADIGITAL INPUT section
OPTICAL
IN jack Connects toaDVD player, etc. The
COAXIAL jack
provides a better
quality of loud
sound (page 20,
22).
COAXIAL IN
jack
BANTENNA section
FM
ANTENNA Connects to the FM wire antenna
supplied with this
receiver (page 24).
AM
ANTENNA Connects to the AM loop antenna
supplied with this
receiver (page 24).
CAUDIO INPUT/OUTPUT section
AUDIO IN/
OUT jack Connects to anMD deck or CD player,
etc. (page 17).
MULTI
CHANNEL
INPUT jack
Connects to a
Super Audio CD
player or DVD
player which has
an analog audio
jack for 5.1
channel sound
(page 16).
DVIDEO/AUDIO INPUT/OUTPUT
section
AUDIO IN/
OUT jack Connects the video and audio jacks of
a VCR or a DVD
player (page 19,
20, 21, 22, 23).
VIDEO IN/
OUT jack*
White (L)
Red (R)
White (L)
Red (R)
Black
White (L)
Red (R)
Yellow
continued
10
GB
*Youcan watch the selected input image when you
connect the MONITOROUTjackto a TV monitor
(page 19).
You can usethesuppliedremoteRM-AAU005
to operate the receiver and to control the Sony
audio/video components that the remote is
assigned to operate (page 64).
ECOMPONENT VIDEO INPUT/
OUTPUT section
COMPONENT
VIDEO
INPUT/
OUTPUT
jack*
Connects to aDVD
player, TV, or a
satellite tuner. You
can enjoy high
quality image
(page 19, 21, 22).
FSPEAKER section
Connects to
speakers (page 14).
Connects to sub
woofer (page 14).
Green
Blue
Red
Remote commander
Name Function
AAV ?/1Press to turn on or off the
Sonyaudio/videocomponents
that the remote is assigned to
operate (page 64).
If you press ?/1(B) at the
same time, it will turn off the
receiver and other
components (SYSTEM
STANDBY).
Note
The function of the AV ?/1
switch changes automatically
each time you press the input
buttons (W).
123
46
78
0/10 ENTER
9
SYSTEM STANDBY
TV/VIDEO
SLEEP AUTO CAL AV
?/1
VIDEO 1 VIDEO 2 VIDEO 3 DVD
2CH A.F.D.
RETURN/EXIT
TV CH –
PRESET – TV CH + PRESET +
TUNING –
TV
TUNING +
REPLAY ADVANCE
MENU
MOVIE MUSIC
MEMORY DVD MENU
CLEAR
TOOLSDISPLAY MUTING
TV VOL
MASTER VOL
FM MODE
D.TUNING
D.SKIP
DUAL MONO
MD/TAPE SA-CD/CD TUNER AMP MENU
TV ?/1
?/1
-
F
Gg
f
.
HmM
Xx
< <
>
5
>10/
wg
qg
qj
qk
qh
qf
ql
w;
wa
ws
wd
wf
qd
AV ?/1
(on/standby) switch
TV ?/1, ?/1
(on/standby) switch
1
3
2
5
6
7
8
q;
9
qs
qa
4
11
GB
Getting Started
Name Function
BTV ?/1Press TV ?/1and TV (M) at
the same time to turn the TV
on or off.
?/1Press to turn the receiver on or
off.
To turn off all components,
press ?/1and AV ?/1(A) at
the same time (SYSTEM
STANDBY).
CAMP MENU Press to display the menu of
the receiver. Then, use the
control buttons to perform
menu operations.
DMOVIE,
MUSIC Press to select sound fields (MOVIE, MUSIC).
EDUAL MONO Press to select the language
you want during digital
broadcast.
FFM MODE Press to select FM monaural
or stereo reception.
GD.TUNING Press to enter direct tuning
mode.
D.SKIP Press to skip disc of the CD
player or DVD player (multi-
disc changer only).
HDVD MENU Press to display the menu of
the DVD player on the TV
screen. Then, use the control
buttons to perform menu
operations.
IENTER Press to enter the value after
selecting a channel, disc or
track using the numeric
buttons.
MEMORY Press to store a station.
JMUTING Press to mute the sound.
KTV VOL
+
a)
/– Press TV VOL +/– and TV (M)atthesame timetoadjust
the TV volume level.
MASTER
VOL +
a)
/– Press to adjust the volume level of all speakers at the
same time.
Name Function
L./>Press to skip tracks of the CD
player, DVD player, MD deck,
or tape deck.
REPLAY /
ADVANCE Press to replay the previous scene or fast forward the
current scene of the VCR or
DVD player.
m/MPress to
–search tracks in the forward/
backward direction of the
DVD player.
–fastforward/rewind of the
VCR, CD player, MD deck,
or tape deck.
H
a)
Press to start playback of the
VCR, CD player, DVD player,
MD deck, or tape deck.
XPress to pause playback or
recording of the VCR, CD
player, DVD player, MD deck,
or tape deck. (Also starts
recording with components in
recording standby.)
xPress to stop playback of the
VCR, CD player, DVD player,
MD deck, or tape deck.
TV CH +/– Press TV CH +/– and TV (M)
at the same time to select
preset TV channels.
PRESET +/– Press to select
–preset stations.
–presetchannels of the VCR
or satellite tuner.
TUNING +/– Press to scan a station.
MTV Press TV and the button you
want at the same time to
activate the buttons with
orange printing.
NMENU Press to display the menus of
the VCR, DVD player, or
satellite tuner on the TV
screen. Then, use the control
buttons to perform menu
operations.
ORETURN/
EXIT OPress to
–return to the previous menu.
–exitthemenuwhile the
menu or on-screen guide of
the VCR, DVD player, or
satellite tuner is displayedon
the TV screen.
<
<
continued
12
GB
a)The number 5,MASTER VOL +, TV VOL +, and
Hbuttons havetactiledots.Usethetactile dotsas
references when operating the receiver.
Notes
Some functions explained in this section may not
work depending on the model.
The above explanation is intended to serve as an
example only. Therefore, depending on the
component, the above operation may not be
possible or may operate differently than described.
Name Function
PControl
buttons After pressing AMP MENU
(C), DVD MENU (H), or
MENU(N),pressthecontrol
button V, v, Bor bto select
the settings. When you press
DVDMENUorMENU,press
the control button to enter the
selection.
QDISPLAY Press to select information
displayed on the TV screen of
the VCR, satellite tuner, CD
player, DVD player, or MD
deck.
RTOOLS Press to display options
applicable to the entire disc
(e.g.discprotection),recorder
(e.g. audio settings during
recording), or multiple items
on a list menu (e.g. erasing
multiple titles).
S-/-- Press -/-- and TV (M) at the
same time to select the
channel entry mode, either
one or two digits of the TV.
>10/
x
Press to select
–track numbers over 10 of the
VCR, satellite tuner, CD
player or MD deck.
–channel numbers of the
Digital CATV terminal.
CLEAR Press to
–clear a mistake when you
press the incorrect numeric
button.
–returntocontinuous
playback, etc. of the satellite
tuner or DVD player.
TNumeric
buttons
(number 5a))
Press to
–preset/tune to preset
stations.
–select track numbers of the
CD player, DVD player or
MD deck. Press 0/10 to
select track number 10.
–select channel numbers of
the VCR or satellite tuner.
Press the numeric buttons and
TV (M) at the same time to
select the TV channels.
UA.F.D. Press to select A.F.D. mode.
V2CH Press to select 2CH STEREO
mode.
Name Function
WInput buttons Press one of the buttons to
select the component you
want to use. When you press
any of the input buttons, the
receiver turns on. The buttons
are factory assigned to control
Sony components as follows.
You can change the button
assignments following the
steps in ìC hanging button
assignmentsî on page 64.
XTV/VIDEO Press TV/VIDEO and TV
(M) at the same time to select
the input signal (TV input or
video input).
SLEEP Press to activate the Sleep
Timer function and the
duration which the receiver
turns off automatically.
YAUTO CAL Press to activate the Auto
Calibration function.
Button Assigned Sony
component
VIDEO 1 VCR (VTR mode 3)
VIDEO 2 VCR (VTR mode 2)
VIDEO 3 Not assigned
DVD DVD player
MD/TAPE MD deck
SA-CD/CD Super Audio CD/CD
player
TUNER Built-in tuner
All manuals and user guides at all-guides.com
all-guides.com

7
STR-DG500/DG600
STR-DG600:
5
US
Getting Started
Description and location of parts
To remove the cover
Press PUSH.
When you remove the cover, keep it out of
reach from children.
Getting Started
Front panel
?/1
AUTO CAL MIC
SPEAKERS
(OFF/A/B/A+B)
PHONES
MEMORY/
ENTER CATEGORY
MODE CATEGORY 2CH A.F.D. MOVIE MUSIC
MULTI CHANNEL DECODING
TUNING MODE DISPLAY INPUT MODE
INPUT SELECTOR
TUNING
–
MULTI CH IN DIRECT
MASTERVOLUME
VIDEO 3 IN/PORTABLE AV IN
VIDEO L AUDIO R DIGITAL(OPT)
PUSH
15268q
;
4397
qaqsws qdqfw;wa qgqhqkql qj
Name Function
A?/1Press to turn the receiver
on or off (page 30, 38, 39,
60, 85).
BSPEAKERS
(OFF/A/B/A+B) Press to select OFF, A, B, A+B of the front speakers
(page 32).
CTUNING MODE Press to select the tuning
mode (page 61, 63, 85).
DTUNING +/– Turn to scan a station
(page 61, 62).
continued
+
6
US
Name Function
EDisplay The current status of the
selected component or a
list of selectable items
appears here (page 7).
FMULTI
CHANNEL
DECODING
lamp
Lights up when multi
channel audio is decoded
(page 39).
GRemote sensor Receives signals from
remote commander.
HDISPLAY Press toselectinformation
displayed on the display
(page 73).
IINPUT MODE Press to select the input
mode when the same
componentsareconnected
to both digital and analog
jacks (page 71).
JMASTER
VOLUME Turn to adjust the volume level of all speakers atthe
same time (page 36, 37,
38, 39).
KDIRECT Press to listen to high
quality analog sound
(page 59).
LMULTI CH IN Press to select the audio
directly from the
components connected to
the MULTI CH IN jacks
(page 37).
MINPUT
SELECTOR Turn to select the input source to playback (page
37, 38, 39, 59, 61, 63, 71,
72, 74).
NMOVIE,
MUSIC Presstoselectsoundfields (MOVIE, MUSIC) (page
56).
OA.F.D. Press to select A.F.D.
mode (page 54).
P2CH Press to select 2CH
STEREO mode (page 59,
60).
Name Function
QCATEGORY +/– Press to select a category
(page 67).
RCATEGORY
MODE Press to select the category mode (page 67).
SMEMORY/
ENTER Press to store a station or enter the selection when
selecting the settings
(page 31).
TVIDEO 3 IN/
PORTABLE AV
IN jacks
To connect a camcorder or
video game (page 28, 37).
UAUTO CAL MIC
jack Connects to the supplied ECM-AC2 optimizer
microphone for the Auto
Calibration function (page
32).
VPHONES jack Connects to a headphone
(page 81).
7
US
Getting Started
About the indicators on the display
MEMORY
L C R
SL S SR
SBRSBL SB
SW
LFE
SP A
SP B
CAT
STEREO MONO A.DIRECT D.RANGE EQ
NEO:6
SLEEP OPT COAX 96/24
DIGITAL EX ; DTS-ES ;
PRO LOGIC IIx
qd qs qa
qh
qj
qfqg
214356789
q;
Name Function
ASW Lights up when sub woofer
selection is set to “YES” (page
43) and the audio signal is
output from the SUB WOOFER
jack.
BLFE Lights up when the disc being
played back contains an LFE
(Low Frequency Effect)
channel and the LFE channel
signal is actually being
reproduced.
CSP A/SP B Lights up according to the
speaker system used. However,
these indicators do not light up
if the speaker output is turned
off or if a headphone is
connected.
D;DIGITAL
(EX) Lights up when Dolby Digital signals are input. “;
DIGITAL EX” lights up when
Dolby Digital Surround EX
signals are decoded.
Note
When playing a Dolby Digital
format disc, be sure that you
have made digital connections
and that INPUT MODE is not
set to “ANALOG” (page 71).
Name Function
E;PRO
LOGIC (II)/
(IIx)
Lights up when the receiver
applies Pro Logic processing to
2 channel signals in order to
output the center and surround
channel signals. “; PRO
LOGIC II” lights up when the
Pro Logic II Movie/Music/
Game decoder is activated.
“; PRO LOGIC IIx” lights up
when the Pro Logic IIx Movie/
Music/Game decoder is
activated. However, these
indicators do not light up if both
the center and surround
speakers are set to “NO” (page
43) and you select a sound field
using the A.F.D. button.
Note
Dolby Pro Logic IIx decoding
does not function for DTS
format signals or for signals
with a sampling frequency of
more than 48 kHz.
FDTS (-ES)/
(96/24) Lights up when DTS signals are input. “DTS-ES” lights up
when DTS-ES signals are input.
“DTS96/24”lightsup when the
receiver is decoding DTS 96
kHz/24 bit signals.
Note
When playing a DTS format
disc,be surethat you havemade
digital connections and that
INPUT MODE is not set to
“ANALOG” (page 71).
GNEO:6 Lights up when DTS Neo:6
Cinema/Music decoder is
activated (page 55).
continued
8
US
HMEMORY Lights up when a memory
function, such as Preset
Memory (page 62), etc., is
activated.
IA.DIRECT Lights up when ANALOG
DIRECT is selected (page 59).
JPreset
station
indicators
Lights up when using the
receiver to tune in radio stations
you have preset. For details on
presetting radio stations, see
page 62.
KTuner
indicators Lights up when using the receiver to tune in radio stations
(page 60), etc.
LEQ Lights up when the equalizer is
activated (page 41).
MD.RANGE Lights up when dynamic range
compression is activated (page
41).
NCOAX Lights up when INPUT MODE
is set to “AUTO” and the source
signal is a digital signal being
input through the COAXIAL
jack, or when INPUT MODE is
set to “COAX IN” (page 71).
OOPT Lights up when INPUT MODE
is set to “AUTO” and the source
signal is a digital signal being
input through the OPTICAL
jack, or when INPUT MODE is
set to “OPT IN” (page 71).
PSLEEP Lights up when the sleep timer
is activated (page 73).
Name Function
QPlayback
channel
indicators
L
R
C
SL
SR
S
SBL
SBR
SB
The letters (L, C, R, etc.)
indicate the channels being
played back. The boxes around
the letters vary to show how the
receiver downmixes the source
sound (based on the speaker
settings).
Front Left
Front Right
Center (monaural)
Surround Left
Surround Right
Surround (monaural or the
surround components obtained
by Pro Logic processing)
Surround back left
Surround back right
Surround back (the surround
back components obtained by
6.1 channel decoding)
Example:
Recording format (Front/
Surround): 3/2.1
Outputchannel: When surround
speaker is set to “NO” (page 43)
Sound Field: A.F.D. AUTO
Name Function
L C R
SL SR
SW
All manuals and user guides at all-guides.com

8
STR-DG500/DG600
9
US
Getting Started
Rear panel
32
DIGITAL
VIDEO 1
IN
VIDEO 2
IN
MD/
TAPE
IN
MD/
TAPE
OUT
DVD
IN
SA-CD/
CD
IN
COAXIAL
OPTICAL
ANTENNA
AM
XM
1
DVD
IN VIDEO 2 IN MONITOR OUT
COMPONENTVIDEO AC OUTLET
Y
ASSIGNABLE
P B /C B
/BñY
P
R /C R
/RñY
SURROUND BACK
R
L
CENTER
+ – + –
SPEAKERS
SURROUND FRONT A
R
R
L
L
+ – + –
SPEAKERS
FRONT B
R
L
+ –
SA-CD / CD MD/TAPE
OUT
L
R
IN
L
R
AUDIO IN
VIDEO IN
DVD
AUDIO ININ
AUX
IN
S-VIDEO
IN
VIDEO OUT
S-VIDEO
OUT
VIDEO IN
VIDEO 2
AUDIO IN
S-VIDEO
IN
VIDEO OUT
VIDEO 1
AUDIO OUT
S-VIDEO
OUT
VIDEO IN
S-VIDEO
IN
L
R
MONITOR
L
R
SURROUND
SUB
WOOFER SUB WOOFER
CENTER
FRONT
L
R
SURROUND
PRE OUT
L
R
MULTI CH IN
456
ADIGITAL INPUT/OUTPUT section
OPTICAL
IN/OUT jack Connects to a DVD player, etc. The
COAXIAL jack
provides a better
qualityofloudsound
(page 18, 25, 27).
COAXIAL IN
jack
BVIDEO/AUDIO INPUT/OUTPUT
section
AUDIO IN/
OUT jack Connects the video and audio jacks of a
VCR or a DVD
player (page 24, 25,
26, 27, 28).
VIDEO IN/
OUT jack*
S-VIDEO IN/
OUT jack*
White (L)
Red (R)
Yellow
CCOMPONENT VIDEO INPUT/
OUTPUT section
COMPONENT
VIDEO INPUT/
OUTPUT jack*
Connects toaDVD
player, TV, or a
satellite tuner. You
can enjoy high
quality image
(page 24, 26, 27).
DSPEAKER section
Connects to
speakers (page 16).
Connects to sub
woofer (page 16).
Green
Blue
Red
continued
10
US
*Youcan watch the selected input image when you
connect the MONITOROUT jack to a TV monitor
(page 24).
EAUDIO INPUT/OUTPUT section
AUDIO IN/
OUT jack Connects to anMD deck or CD player,
etc. (page 21).
MULTI
CHANNEL
INPUT jack
Connects to a
Super Audio CD
player or DVD
player which has
an analog audio
jack for 5.1
channel sound
(page 20).
PRE OUT
jack Connects to an external power
amplifier.
FANTENNA section
FM
ANTENNA Connects to the FM wire antenna
supplied with this
receiver (page 29).
AM
ANTENNA Connects to the AM loop antenna
supplied with this
receiver (page 29).
XM
ANTENNA Connects to the XM Connect-and-Play
antenna (not
supplied) (page 65).
White (L)
Red (R)
White (L)
Red (R)
Black
White (L)
Red (R)
11
US
Getting Started
You can use the supplied remote RM-AAP012
to operate the receiver and to control the Sony
audio/video components that the remote is
assigned to operate. You can also program the
remote to control non-Sony audio/video
components. For details, see “Programming
the remote” (page 75).
Remote commander
HX
mM
.>
-
VIDEO1 VIDEO2
RM SET UP
SYSTEM STANDBY SLEEP
TV ?/1 AV ?/1
VIDEO3 DVD
MD/TAPE SA-CD/CD TUNER AUX
MULTI CH
TOP MENU/
GUIDE AV MENU MUTING
MASTER
VOL
DISPLAY
TV VOL TV CH
WIDE AUTO
CAL
TV/
VIDEO AMP MENU
RETURN/EXIT
D.TUNING DISC ALT
ANT CLEAR SEARCH MODE
2CH A.F.D.
123
456
789
0/10 >10/11 12
MOVIE
SUBTITLEMEMORY ENTER
MUSIC
AUDIO ANGLE
TUNING JUMP/
TIME PRESET/ CH/D.SKIP
CATEGORY
MODE
DUAL
MONO
x
?/1
P
O
f
F
Gg
CATEGORY
TV ?/1 (on/standby) switch
8
wl
ql
wa
wd
ws
w;
wg
wh
wj
wk
6
qa
5
7
q;
qs
qf
9
3
4
AV ?/1(on/standby) switc
h
?/1 (on/standby) switch
1
2
qh
wf
qk
qj qd
qg
continued
12
US
Name Function
AAV ?/1Press to turn on or off the
audio/video components that
the remote is programmed to
operate.
If you press ?/1(B) at the
same time, it will turn off the
receiver and other
components (SYSTEM
STANDBY).
Note
The function of the AV ?/1
switch changes automatically
each time you press the input
buttons (wj).
B?/1Press to turn the receiver on or
off.
To turn off all components,
press ?/1and AV ?/1(A) at
the same time (SYSTEM
STANDBY).
SLEEP Press ALT(G)andthenpress
SLEEP to activate the Sleep
Timer function and the
duration which the receiver
turns off automatically.
CMULTI CH Press to select the audio
directly from the components
connected to the MULTI CH
IN jacks.
DMUSIC Press to select sound fields
(MUSIC).
EE CATEGORY
MODE Press to select the category mode for XM Radio (page
67).
FPRESET/
CH/D.SKIP
+/–
Press to
–select preset stations.
–select preset channels of the
TV, VCR, satellite tuner,
Blu-ray disc recorder, or
hard disc recorder.
–skip disc of the CD player,
VCD player, DVD player,
MD deck, or LD player
(multi-disc changer only).
GALT Press to light up the button. It
changes the remote key
function to activate the
buttons with orange printing.
Name Function
H-/-- Press to select the channel
entry mode, either one or two
digit of the TV, Blu-ray disc
recorder, hard disc recorder,
PSX, or satellite tuner.
DISC Press to select a disc directly
of the CD player or VCD
player (multi-disc changer
only).
SEARCH
MODE Press to select the searching mode or unit for search
(tracks, index, etc.) of the
DVD player.
IxPress to stop playback of the
VCR,CDplayer,VCD player,
LD player, DVD player, MD
deck, DAT deck, tape deck,
Blu-ray disc recorder, hard
disc recorder, or PSX.
JMUTING Press to mute the sound.
KMASTER
VOL +
a)
/– Press to adjust the volume level of all speakers at the
same time.
LAMP MENU Press to display the menu of
the receiver. Then, use the
control buttons to perform
menu operations.
MTV/VIDEO Press to select the input signal
(TV input or video input).
NAUTO CAL Press to activate the Auto
Calibration function.
OWIDE PressALT (G)andthenpress
WIDE to select the wide
picture mode.
PTV CH +
a)
/– Press to select preset TV
channels.
QTV VOL
+
a)
/– Press to adjust the TV volume level.
RRETURN/
EXIT OPress to –return to the previous menu.
–exitthemenuwhile the
menu or on-screen guide of
the VCD player, LD player,
DVD player, Blu-ray disc
recorder, hard disc recorder,
PSX, or satellite tuner is
displayed on the TV screen.
All manuals and user guides at all-guides.com

9
STR-DG500/DG600
13
US
Getting Started
Name Function
SDISPLAY Press to select information
displayed on the TV screen of
the TV, VCR, VCD player,
LD player, DVD player, CD
player, MD deck, Blu-ray disc
recorder, hard disc recorder,
PSX, or satellite tuner.
TControl
buttons After pressing AMP MENU (L), TOP MENU/GUIDE
(U), or AV MENU (V),
press the control button V, v,
Bor bto select the settings.
When you press TOP MENU/
GUIDE or AV MENU, press
the control button to enter the
selection.
UTOP MENU/
GUIDE Press to display the –DVD title.
–menu or on-screen guide of
the satellite tuner, Blu-ray
disc recorder, hard disc
recorder, or PSX on the TV
screen.
Then, use the control buttons
to perform menu operation.
VAV MENU Press to display the menus of
the VCR, DVD player,
satellite tuner, Blu-ray disc
recorder, hard disc recorder,
or PSX on the TV screen.
Then, use the control buttons
to perform menu operations.
WH
a)
Press to start playback of the
VCR,CDplayer,VCDplayer,
LD player, DVD player, MD
deck, DAT deck, tape deck,
Blu-ray disc recorder, hard
disc recorder, or PSX.
XXPress to pause playback or
recording of the VCR, CD
player, VCD player, LD
player, DVD player, MD
deck, DAT deck, tape deck,
Blu-ray disc recorder, hard
disc recorder, or PSX. (Also
starts recording with
components in recording
standby.)
Name Function
Ym/MPress to
–searchtracks in the forward/
backward direction of the
CD player, VCD player,
DVDplayer,LD player,MD
deck, Blu-ray disc recorder,
hard disc recorder, or PSX.
–fast forward/rewind of the
VCR, DAT deck, or tape
deck.
D. TUNING Press to enter direct tuning
mode.
ANT PressALT (G)andthenpress
ANT to select the signal to be
output from the antenna
terminal of the VCR or
satellite tuner (TV signal or
video signal).
CLEAR PressALT (G)andthenpress
CLEAR to
–clearamistake when you
press the incorrect numeric
button.
–returntocontinuous
playback, etc. of the CD
player, DVD player, Blu-ray
disc recorder, PSX, or
satellite tuner.
ZCATEGORY
+/– Press to select the category for XM Radio (page 67).
TUNING +/– Press to scan a station.
./>Press to skip tracks of the
VCR,CDplayer,VCDplayer,
LD player, DVD player, MD
deck, DAT deck, tape deck,
Blu-ray disc recorder, hard
disc recorder, or PSX.
2CH Press to select 2CH STEREO
mode.
A.F.D. Press to select A.F.D. mode.
MOVIE Press to select sound fields
(MOVIE).
DUAL MONO Press to select the language
you want during digital
broadcast.
continued
14
US
a)
The MASTER VOL +, TV VOL +, TV CH + and
Hbuttons havetactiledots.Usethetactile dotsas
references when operating the receiver.
Notes
Some functions explained in this section may not
work depending on the model.
The above explanation is intended to serve as an
example only. Therefore, depending on the
component, the above operation may not be
possible or may operate differently than described.
The 12 button on the remote is not available for
receiver operation.
Name Function
AUDIO Press to change the sound to
Multiplex, Bilingual or Multi
channel TV sound of the TV,
VCR, DVD player, satellite
tuner, Blu-ray disc recorder,
hard disc recorder, or PSX.
ANGLE Press to select the viewing
angle or change the angles of
the DVD player or Blu-ray
disc recorder.
JUMP/TIME Press to
–toggle between the previous
and the current channels of
the satellite tuner, TV, or
Blu-ray disc recorder.
–showthe time or display the
playing timeofadisc,etc.of
the CD player, MD deck,
VCD player, or DVD player.
MEMORY Press MEMORY to store a
station.
SUBTITLE PressALT(G)andthenpress
SUBTITLE to change the
subtitles of the DVD player.
ENTER Press ALT(G)andthenpress
ENTER to enter the value
after selecting a channel, disc
or track using the numeric
buttons.
Numeric
buttons PressALT (G)andthenpress the numeric buttons to
–preset/tune to preset
stations.
–select track numbers of the
CD player, VCD player,LD
player, DVD player, MD
deck, DAT deck, or tape
deck. Press 0/10 to select
track number 10.
–select channel numbers of
the TV, VCR, satellite tuner,
Blu-ray disc recorder, hard
disc recorder, or PSX.
>10/11 PressALT (G)andthenpress
>10/11 to select track
numbers over 10 of the CD
player, VCD player, LD
player, MD deck, tape deck,
TV, VCR, Blu-ray disc
recorder, hard disc recorder,
PSX, or satellite tuner.
Name Function
wj Input buttons Press one of the buttons to
select the component you
want to use. When you press
any of the input buttons, the
receiver turns on. The buttons
are factory assigned to control
Sony components as follows.
You can program the remote
to control non-Sony
components following the
steps in “Programming the
remote” on page 75.
wk TV ?/1Press to turn the TV on or off.
wl RM SET UP Press to set up the remote.
Button Assigned Sony
component
VIDEO1 VCR (VTR mode 3)
VIDEO2 VCR (VTR mode 1)
VIDEO3 VCR (VTR mode 2)
DVDDVD player
MD/TAPE MD deck
SA-CD/CD Super Audio CD/CD
player
TUNER Built-in tuner
AUXNot assigned
All manuals and user guides at all-guides.com

10
STR-DG500/DG600
Note : This set can be disassemble according to the following sequence.
SECTION 2
DISASSEMBLY
2-1. CASE
2-1. CASE
(Page 10)
2-2. FRONT PANEL SECTION
(Page 11) 2-3. BACK PANEL SECTION
(Page 11)
SET
2-6. STANDBY BOARD
(Page 13) 2-4. DIGITAL BOARD
(Page 12) 2-7. SB AMP BOARD (DG600)
(Page 13)
2-5. MAIN BOARD SECTION
(Page 12)
Note : Follow the disassembly procedure in the numerical order given.
1 two screws
(case 3 TP2)
2 two screws
(case 3 TP2)
3 two screws
(+BVTP 3
× 8
)
4 case
All manuals and user guides at all-guides.com

11
STR-DG500/DG600
2-2. FRONT PANEL SECTION
2-3. BACK PANEL SECTION
7 five screws
(+BVTP 3
× 8)
6 two screws
(+BVTP 3
× 8)
1 CNP2000 (4P)
2 CNP791 (4P)
8 front panel section
3 CNS505 (23 core)
4 CNP202 (3P)
5 CNP503 (3P
)
0 screw
(+BVTP 3
× 8)
qa three screws
(+BVTP 3
× 8)
qs six screws
(+BVTP 3
× 8)
qd five screws
(+BVTP 3
× 8)
qf four screws
(+BVTP 3
× 8)
qg back panel section
1 CNP901 (2P)
7 CNP503 (4P)
8 CNP504 (2P)
9 CNP203 (3P)
3 CNS509 (17 core)
5 CNS503 (9 core)
6 CNS504 (5 core)
4 CNS508 (11 core) (except AEP,UK
)
CNS508 (15 core) (AEP,UK)
2 CNP806 (3P)
All manuals and user guides at all-guides.com
all-guides.com

12
STR-DG500/DG600
2-4. DIGITAL BOARD
2-5. MAIN BOARD SECTION
4 screw
(+BVTP 3
× 8)
5 DIGITAL boar
d
1 CNP505 (10P)
2 CNP503 (5P)
3 CNP504 (7P)
5 two screws
(+BV3 (3
-CR) )
8 MAIN board section
6 two screws
(+BV3 (3
-CR) )
7 screw
(+BV3 (3
-CR) )
1 CNP600 (5P)
3 CNP801 (3P)
4 CNP802 (5P)
2 CNP601 (4P)
All manuals and user guides at all-guides.com

13
STR-DG500/DG600
2-6. STANDBY BOARD
2-7. SB AMP BOARD (DG600)
3 screw
(+BVTP 3 × 8)
4 STANDBY board
1 CNP902 (2P)
2 CNP804 (3P)
3 two screws
(+BVTP 3 × 8)
4 three screws
(transister)
5 SB AMP board
MAIN board section
1 CN2571 (9P)
2 CN2570 (5P)
All manuals and user guides at all-guides.com

14
STR-DG500/DG600 SECTION 3
TEST MODE
FACTORY PRESET MODE
* All preset contents are reset to the default setting.
* Procedure:
While depressing the [SPEAKERS $OFF/A/B/A+B%] and the
[MOVIE] buttons simultaneously, press the ?/1 button to turn
on the main power.
The message “FACTORY” appears for a moment and the present
contents are reset to the default values.
AM CHANNEL STEP 9 kHz/10 kHz SELECTION
MODE (US, Canadian, E2 model only)
* Either the 9 kHz step or 10 kHz step can be selected for theAM
channel step.
* Procedure:
Turn the [INPUT SELECTOR] control to set AM and press the
?/1 button to turn off the main power.
While depressing the [TUNING MODE] button, press the ?/1
button to turn on the main power.
Either the message “9k STEP” or “10k STEP” appears for a
moment and select the desired step.
VACUUM FLUORESCENT DISPLAY TEST MODE
* All fluorescent segments are tested.
When this test is activated, all segments light on at the same
time, then each segment lights on one after another.
* Procedure:
While depressing the [TUNING MODE] and the [DISPLAY] but-
tons simultaneously, press the ?/1 button to turn on the main
power.
1. ALL segments light on.
[MULTI CHANNEL DECODING] LED light on.
2. Turn the [INPUT SELECTOR] control, confirm display.
3. Turn the [INPUT SELECTOR] control, confirm display.
[MULTI CHANNEL DECODING] LED light on.
4. Turn the [INPUT SELECTOR] control, all segments and all LEDs
light off.
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated.
Use this mode before returning the product to clients upon
completion of repair.
* Procedure:
While depressing the [2CH] button, press the ?/1 button to turn
on the main power.
The message “S.F. CLR.” appears for a moment and initializa-
tion is performed.
SOFTWARE VERSION DISPLAY MODE
* The software version is displayed.
* Procedure:
While depressing the [SPEAKERS $OFF/A/B/A+B%] and the
[DISPLAY] buttons simultaneously, press the ?/1 button to turn
on the main power.
The model name, destination and the software version are dis-
played for a moment.
KEY CHECK MODE
* Button check
* Procedure:
While depressing the [SPEAKERS $OFF/A/B/A+B%] and the [2CH]
buttons simultaneously, press the ?/1 button to turn on the main
power.
Either the message “REST 13” (STR-DG500) or “REST 14”
(STR-DG600) appears.
Every pressing of any button other than the ?/1 counts down
the buttons.The buttons which are already counted once are not
counted again.When all buttons are pressed “REST 00” appears.
AUTOBETICAL MODE (AEP, UK model only)
* When this mode is used, the receiver scans the broadcasts that
can be received by the tuner, and sets up the broadcasts.
Be sure to start scanning after connecting the antenna.
* Procedure:
Check that the antenna is connected.
While depressing the [MEMORY/ENTER] button, press the ?/1
button to turn on the main power.
The message “AUTO-BETICAL SELECT” appears for a mo-
ment and the receiver starts scanning.
COMMAND MODE SELECTION MODE
* The command mode (AV1 or AV2) of the remote commander
can be selected.
* Procedure:
While depressing the [INPUT MODE] button, press the ?/1 but-
ton to turn on the main power.
Either the message “C.MODE.AV 1” or “C.MODE.AV 2” ap-
pears for a moment and select the desired mode.
L
SW LFE
CR
SL S SR
SBL SB SBR
SP A
SP B SLEEP OPT COAX HDMI 96/24
DIGITAL EX PRO LOGIC II x DTS-ES NEO:6 AAC CAT RDS
D.RANGE EQ STEREO MONO A.DIRECT
D
D D D
dB
k Hz
m ft.
MHz
MEMORY
L
SW LFE
R
S
SB
A
SLEEP COAX 96/24
EX DTSII NEO:6 CAT
D.RANGE STEREO
dB
Hz
ft.
MEMORY
C
SL SR
SBL SBR
SP
SP B OPT HDMI
DIGITAL xPRO LOGIC -ES AAC RDS
EQ MONO A.DIRECT
D
D D D
k
m
MHz
All manuals and user guides at all-guides.com

STR-DG500/DG600
15 15
STR-DG500/DG600
4-1. BLOCK DIAGRAM — TUNER/AUDIO SECTION —
SECTION 4
DIAGRAMS
43
76
75
78
74
73
70
SA-CD/CD
IN
MD/TAPE
OUT
MD/TAPE
IN
DVD AUDIO
IN
VIDEO 3 IN/
PORTABLE AV IN
L
J400(DG600)
J402(DG500)
DG600
J403 J298(2/2) J404
R
R–CH R–CH R–CH R–CH
LR
AM
TN1
FM/AM TUNER UNIT
SYSTEM CONTROL
IC1101 (1/5)
LRLR L
-3 -4 -1 -2 -5 -6
RL
VIDEO 2
AUDIO OUT AUDIO INAUDIO IN
RLR
R–CH
RDS SIG/XM REQ
S LATCH
SW RY
VOL DA
VOL CL
STEREO
TUNED
MUTE
DO
17 TUNER DATA/FL DATA
16 T.SERIAL CLK/FL CLK
L–CH
AEP,UK MODEL
AEP,UK MODEL
EXCEPT
AEP,UK MODEL
R–CH
STEREO
TUNED
MUTING
CE
DO
DATA
CLOCK
VIDEO 1
AUDIO
OUT
SUB
WOOFER
SUB
WOOFER
PRE
OUT
RELAY
DRIVER
Q560
SUB WOOFER
AMP
IC402
J309
RY560
DG500
DG600
XM L
XM R
XM REQ
XM DBPOWER
SBL–CH
C–CH
SR–CH
R–CH
SL–CH
L–CH
R–CH
L–CH
R–CH
TU+3.3V
11
14
60
59
XM_RST
XM DACMS
26
47
FM 75Ω
COAXIAL
44
45
24
25
68 66
32
28
30
34
38
60
59
46
SUB
WOOFER
LR
R–CH R–CH
LR
FRONT SURROUND
CENTER
J401
MULTI CH IN
ANTENNA
10
13
12
41
42
88
87
85
84
86
81
SBR–CH
83
82
5 7
54 56 51 52 49
SW
SEL
C
SEL
SL
SEL
L
SEL
R–CH
R–CH
26
27
R–CH
R–CH
R–CH
R–CH
R–CH
R–CH
DIR
FUNCTION SELECT
IC401
AVCCAVEE
+7V–7V
-3 -4 -1 -2
AUDIO
R–CH
LR
22
-2 -3-3 -4
AUX
IN
LR
R–CH
-5 -6 -1 -2
-5 -6 -3 -4 -1 -2
SEL
SW
MCU
I/F
3.3V
(STBY)
SBL OUT
R–CH
SW OUT
C OUT
SL OUT
L OUT
R–CH
R–CH
TU+10V
52 RDS CLK/XM DPOWER
RDS INT
FM SIG OUT
53 RDS DATA/XM COMMAND
RDS DATA
• Signal path
: TUNER (FM/AM)
: VIDEO (AUDIO)
: CD (ANALOG)
• R
– ch is omitted due to
same as L
– ch.
SBL
SEL
36
XM COMMAND
XM DACMS
XM RESET
FL CLK
FL DATA
XM
SECTION
C
KEY/
DISPLAY
SECTION
D
DIGITAL
SECTION
B
17
DIGITAL
SECTION
A
POWER
SECTION
E
(Page 18)
(Page 19)
(Page 16)
(Page 16)
(Page 20)
All manuals and user guides at all-guides.com

STR-DG500/DG600
1616
STR-DG500/DG600
4-2. BLOCK DIAGRAM — DIGITAL SECTION —
• Signal path
: TUNER (FM/AM)
: VIDEO (AUDIO)
: CD (ANALOG)
: CD (DIGITAL)
: VIDEO
• R-ch is omitted due to
same as L-ch.
1
+5V-2
A.5V
SDI1 SD01
DOUT 15 18
GP8
AUDIO 24
SYS CLK
16
XMCK
20
69
LRCKI1
15
BCKI1
17
KFSI0
CKOUT 13 22
BCKI2
BCK 14 29
LRCKI2
LRCK 15 28
SDI2
CS
WE
DATAO
LRCK 13
BCK 14
23
SD02 24
SD03 25
SD04 26
SCKOUT 14
LRCKO 19
BCKO
LRCKO
SCKOUT
BCKO
20
X1502
13.9MHz
X1301
12.288MHz
MCLK1 9
MCLK2 12
CSO 44
WEO 45
68
108,107,105 -102,99,
98,80 - 77,75 - 72
24 - 27,42 - 44,
1 - 5,18 - 21
29 - 32,35 - 38,
16-13,10 - 7
112,110,109,97 - 92,
85-82,66 - 64
6
17
211336 35 33 3432
21
37
6 74 18 19 205
EXLOCK
GP12 56
BST
ERROR
21
22
RST
6
95 96 97 98
38 37 36 35 33 47 17
INPUT DATA
DEMODULATOR
Pa,Pb DETECTION LOCK
DETECTION
MICROPROCESSOR
I/F
C bit DETECTION 34 59
16 30
DVD
IN
DIGITAL
(COAXIAL)
(COAXIAL)
SELECTOR
IC1302
1
(OPTICAL)
OUT
IC1354
SA-CD/CD
IN
3
MD/TAPE
OUT
(OPTICAL)
DIN
IC1353
DG600
DG600
DG500
DG600
1
3 7
14 2
VIDEO 2
IN
VIDEO 1
IN
(OPTICAL)
OUT
IC1351
IC1303
DIGITAL AUDIO
I/F RECEIVER
IC1301
J1301
-1
-2
23 WAVE
SHAPER
IC1103
J1301
23 WAVE
SHAPER
+2.6V
VDDI
+3.3V
VDDE
5
+3.3V
VDD NC
DG600
DG500
L-IN
R-IN R-CH
L IN LPF
DG600 DG500
AUDIO
I/F
ADC
IC1401
DSP
IC1501
SDRAM
IC1502
SWITCH
IC1503
GP9
DATAO
8
GP12
99
ERROR
HACN
HCS
XRST
HDIN
PM
15141312103
BST
92
BST SEL
PCM1609 RST
PCM1609 ML
PCM1609 MC/XMDAC MC
PCM1609 MDO
PCM1609 MDI/XMDAC MDI
57
ADCC_INT
ADCC_INT ADCC_INT
HDOUT
HCLK
GP9 HACN HCS XRST HDIN PM HDOUT HCLK
6
DIR_CLK
DIR CE
DIR DI
DIR DO
XSTATE
CLK CE DI DO BPSYNC CKSEL1
93100
48
XMODE
46
CKSEL0
94
CKSEL1
XMODE XSTATE
5
4
3
XOUT
DIN1
8SDIN
DIN2
2DOUT
DIN0
XIN
AB
D1301
D1503 D1502D1504 D1501
D0-15A0-15 D0-15A0-15
SYSTEM
CONTROL
IC1101 (2/5)
TUNER/
AUDIO
SECTION
B
TUNER/
AUDIO
SECTION A
OE
OEO 43 41
ADC
5
1
MD/TAPE
IN
(OPTICAL)
OUT
IC1352
6
1
DIGITAL
(OPT)
VIDEO 3 IN/
PORTABLE AV IN
OUT
IC200
4
90
SELECT2 SELECT1
91
DATA3
L OUT
C OUT
R-CH
VOUT5
VOUT6
47
310 1
5
97
AMP
IC1403
DATA1
SL OUT
R-CH
SW OUT
XM
SECTION
F
XM DAC MDI
XM DAC MC
VOUT1
VOUT2
45
514 7
3
13 1
AMP
IC1405
AMP
IC1404
DATA2
VOUT3
VOUT4
46
SCKI
38
BCK
40
LRCK
SCKOUT
BCKO
LRCKO 41
ML
36
RST
37
MDI
34
MDO
33
MC
35
LRCKO
312 1
5
11 7
DATA4
SBL OUT
DG600
VOUT7
VOUT8
31
516 7
R-CH
3
20 1
AMP
IC1406
8CH DAC
IC1452
DAC
DAC
DAC
DAC
8
1
2
(Page 15)
(Page 18)
(Page 15)
All manuals and user guides at all-guides.com
all-guides.com

STR-DG500/DG600
17 17
STR-DG500/DG600
4-3. BLOCK DIAGRAM — VIDEO SECTION —
3CH1 IN2
CH2 IN2
CH3 IN2
CH1 IN3
CH2 IN3
CH3 IN3
CHI OUT
CH2 OUT
CH3 OUT
5
9
11
14
12
2 4
Y
P
B/ C B/ B-Y
P
R/ C R/ R-Y
Y
SW1 SW2
COMP SW1 COMP SW2
P
B/ C B/ B-Y
P
R/ C R/ R-Y
J301 (1/2)
(ASSIGNABLE)
(ASSIGNABLE)
J201 (1/2)
22
75Ω
DRIVER
6dB AMP
20
75Ω
DRIVER
6dB AMP
18
75Ω
DRIVER
6dB AMP
10 6 14 2
13
J200 (1/2)
5
3
4
VIDEO 2
IN
DVD
IN
VIDEO
IN
VIDEO
IN
COMPONENT
VIDEO
-4
-5
-6
-1
-2
-3
Y
P
R/ C R/ R-Y
P
B/ C B/ B-Y
J301 (2/2)
MONITOR
OUT
COMPONENT
VIDEO
-7
15
75Ω
DRIVER
RELAY
DRIVER
Q250,251
6dB AMP
1
1 3
75Ω
DRIVER
6dB AMP
-3
J200 (2/2)
J201 (2/2)
-8
-9
-1
VIDEO 1
J298 (1/2)
VIDEO
-1
VIDEO 3 IN/
PORTABLE AV IN
VIDEO 2
DVD
-2
VIDEO
IN
-1
VIDEO
OUT VIDEO 1
-2
VIDEO
OUT MONITOR
+5V
REG
IC807
+5V-3
3 2
-5V
REG
IC804
-5V-3
SW1
SW2
COMP SW1
SIN SOUT
LAT
CLK
OE
DATA
COMP SW2
SW3
SW4 VIDEO
CONTROL
IC1601
D203,204
OR
VEE -5V-3
VCC +5V-3
+15V
-15V
V1.OUT
M.OUT
V-1,-2 -5V-3
V+1,+2+5V-3
V1
V2
DVD
V3
NC
SW2 SW4 SW3 SW1
SW2 SW3 SW4 SW1 SW5
VIDEO
SELECTOR
IC203
COMPONENT VIDEO SELECT
IC304
7
9
OR
J253 (1/2)
J252 (1/2)
J252 (2/2)
S-VIDEO
IN
-2
VIDEO 1
S-VIDEO
IN
-1
DVD
S-VIDEO
IN
-2
VIDEO 2
13
3
5
10 6 14 2
15
75Ω
DRIVER
6dB AMP
1
75Ω
DRIVER
6dB AMP
13
3
5
10 6 14 2
15
75Ω
DRIVER
6dB AMP
1
75Ω
DRIVER
6dB AMP
Y
C
G
G
J253 (2/2)
-1
IC253
RY250
VIDEO 1
Y
C
G
G
MONITOR
Y
C
G
G
Y
C
G
G
Y
C
G
G
J251
VEE -5V-3
VCC +5V-3
VEE -5V-3
VCC +5V-3
V1.OUT
M.OUT
V1.OUT
M.OUT
V1
DVD
V2
7
9
NC
V3
V1
DVD
V2
SW2 SW4 SW1 SW5
SW2
SW4 SW1 SW5
SW2
7
9
NC
V3
SW2
SW4 SW1 SW5
SW4
4
4
SW3
SW3 SW3 SW3
SW1 SW5
Y SWITCH
IC251
C SWITCH
IC252
D251,252
DG600
1 2
SYNC
SEPARATION
HDMI
CONTROL
IC1602
7
13 13
6
5
4
3
2
725
I LINE
MEMORY
COLOR
KILLER
I2C
BUS
DYNAMIC
COMB
FILTER
DAC
27
DAC
ADC
VIDEO AMP
Q327 YC
IN
SYSTEM
CLOCK
YOUT
COUT
FSC
Y/C SEPARATION
IC370
Y PROCESS
Q371 1 4
BUFFER
IC372
15 16
IC375
X372
3.57MHz
UPCON
UPCON CLK
D595 OE
D595 LAT
D595 CLK
D595 DATA
CLOCK
GENERATOR
19
PLL
12 12
11 11
14 9
14
SYSTEM
CONTROL
IC1101 (3/5)
33
4 7
34
88
89
87
86
SCL
DG600
SDA
S-VIDEO
OUT
S-VIDEO
OUT
C PROCESS
Q373 8 5
• Signal path
: VIDEO
All manuals and user guides at all-guides.com

STR-DG500/DG600
1818
STR-DG500/DG600
4-4. BLOCK DIAGRAM — XM SECTION (DG600) —
18 COMRXP
23 COMTXP
J101
XM DIGITAL
TRANSCEIVER
IC102
BUFFER
IC103
X101
45.158MHz
XM
+D
–D
2
322 COMTXM
3
SCTXOUT
5
SCRXIN
7
COMMSEL
9
IRQ
XM64FS
XMDATA
XMFS
XM256FS
3
12
11
2
6
7
5
4
1
39
I2SSCLK
8
17
2
37
I2SDATA
3
41
I2SLRCLK
16
43
I2SOCLK
11
RESET
26 OSCOUT
28 OSCIN
XM MIXMI
XM MIXMO
9
18
XMCOMMAND
XMREQ
13
MD
14
MC
XM DACMDI
XM DACMC
BCK
DATA
LRCK
SCK
15
ML
7
VOUTL
XMDACMS
XML
XMR
XM RESET
DBPOWER
AC1
AC2
19 COMRXT
6 7
8
VOUTR
XM+3.3V
XM+5V
XM+5.3V
2
1
4 2
1
3 1
3 1
RESET
Q101,104
D/A CONVERTER
IC105
XM AMP
IC104
IC106
F40
RECT
D104
IC107
XM+5V
REG
IC101
XM+3.3V
REG
XM5.3V REG
KEY/DISPLAY
SECTION
G
TUNER/AUDIO
SECTION
C
DIGITAL
SECTION
F
(Page 19)
(Page 15)
(Page 16)
All manuals and user guides at all-guides.com

STR-DG500/DG600
19 19
STR-DG500/DG600
4-5. BLOCK DIAGRAM — KEY/DISPLAY SECTION —
83
FL DISPLAY DRIVER
IC100
14
I
29
82
29
30
5
6
65
64
54
SW NETWORK
S101–107,124
RV102
MASTER
VOLUME
D105
MULTI CHANNEL
DECODING
56
51
49
28
27
77
+3.3V
(STBY)
X1
X0
SDA
SCL
POWER KEY
38 ADCC
FLASH1/XM_TX
FLASH2/XM_RX
MD2
MD0
RSTX
SDA
SCL
EEPROM
IC1131
AUTO
CAL MIC
J2000 D2014
X1101
24MHz
XM MIXMO
XM MIXMI
SIRCS
9
4
2
9
FL LAT 9STB
7DIN
8CLK
3
6
8
1
SW1
GRID12
I
GRID1
SEG1
I
SEG16
VOL ENC A
VOL ENC B
A/D2
SW NETWORK
S108–111,115,112 (DG600)
A/D1
DG600
1
3
31
32
21
22
RV101
INPUT
SELECTOR
TUNING A
TUNING B
1
3
RV103
TUNING +/-
ENC A
ENC B
1
3
BUFFER
IC101
1
REMOTE
CONTROL
RECEIVER
IC102
OUT
SIRCS
SYSTEM
CONTROL
IC1101 (4/5)
CNP504
S100
FLASH1
FLASH2
MD2
MD0
RESET
SCL
SDA
1
2
7
6
5
8
9
FLASH
PROGRAMMING
12
I/ I
XM
SECTION G
FL DATA
FL CLK TUNER/
AUDIO
SECTION
D
39
40
FL101
VACUUM
FLUORESCENT
DISPLAY
IC1111
RESET
31
I
42
LED
DRIVER
Q110
15
MIC AMP
IC2000
(Page 18)
(Page 15)
All manuals and user guides at all-guides.com

STR-DG500/DG600
2020
STR-DG500/DG600
4-6. BLOCK DIAGRAM — POWER SECTION —
812
11
DRIVE POWER AMP
Q701-704 CURRENT
DETECT
Q705,706 RY791
RY600
RY601
RY701
PRE DRIVER
IC701
IN 2 +VOUT2
-VOUT2
SPEAKERS
IMPEDANCE
USE 8-16Ω
R
L
FRONT B
L
-1
L
-2
R
SURROUND
SURROUND
BACK
CENTER
R
L
R
R-CH
R-CH
R-CH
R-CH
L-CH
R-CH
SL-CH
C-CH
R-CH
SR-CH R-CH
TUNER/
AUDIO
SECTION
E
RY901
RY801(EXCEPT CND)
RY802,803(CND)
AC1
AC2
F2
+3.3V
(STBY)
+2.6V
+5V-1
-7V
+7V
TU+10V
-20V
RECT
D910-913
T902
POWER
TRANSFORMER
D914
AC IN
DETECT
Q921 D915 AC IN
~
OVERLOAD
DETECT
D740,Q740
1
61
12
11
DRIVE POWER AMP
Q501-504 CURRENT
DETECT
Q505,506
-20V REG
Q801
B- SWITCH
Q691,692
RELAY
DRIVER
Q901
PRE DRIVER
IC501
PRE DRIVER
IC2501
IN2 +VOUT2
-VOUT2
OVERLOAD
DETECT
D540,Q540
812
11
DRIVE POWER AMP
Q651-654 CURRENT
DETECT
Q655,656
PRE DRIVER
IC601
IN 2 +VOUT2
-VOUT2
OVERLOAD
DETECT
D640,Q640
RELAY
DRIVER
Q790
RELAY
DRIVER
Q610
RY501
RY500
DG500
DG600
RELAY
DRIVER
Q550
RELAY
DRIVER
Q760
69
66
62
PROTECTOR
D721,722,732
Q722,723,725,793,795
55
58
48
68
F1
OVERLOAD
DETECT AMP 72
IC691
-B-1
-B
+3.3V/+2.6V
REG 4
5
+3.3V 2
IC1901
+5V-2 +5V
REG 13
IC1001
TU+3.3V +3.3V
REG 13
IC1071
+3.3V
REG 13
IC1904
+9V
REG 13
IC1902
-15V
+15V
+7V
REG 31
IC801
-7V
REG 13
IC802
+5V
REG 13
IC1031
+B
+B-1
R-CH
R-CH
R-CH
-B-1 +B-1
R-CH
R-CH R-CH
RECT
D802
RECT
D920-923
RECT
D805-808
T901
POWER
TRANSFORMER
TM600(DG600)
TM602(DG500)
R
FRONT A
SURROUND PRE OUT
L
R-CH
TM601
J310
TM501
J791
PHONES
HP-RY SB-RY FRONT RY REAR-RY C/SB RY HP DETECT
HP-RY
HP DETECT
SB-RY
FRONT-RY
REAR-RY
C/SB RY
HP_RY
FRONT RY
REAR_RY
PROTECTOR
HP DETECT
P0WER RY
67
SP_B_RY
72
BRIDGEABLE RY
STOP
C/SB RY AEP,UK MODEL
SYSTEM
CONTROL
IC1101 (5/5)
PRE
DRIVE
PRE
DRIVE
62
3
DRIVE POWER AMP
Q533,534,571,572
CURRENT
DETECT
Q535,536
IN1
DG600
D1110 D1108 D1107 D1111
DG600
+VOUT1
-VOUT1
OVERLOAD
DETECT
D580,Q580
TM502
PRE
DRIVE
SBR-CH
SBL-CH
16
5
DRIVE POWER AMP
Q2572-2574 CURRENT
DETECT
Q2575,2576
IN+ +VOUT
-VOUT
OVERLOAD
DETECT
D2575,Q2577
-B-1 +B-1
-B-1 +B-1
-B-1 +B-1
PRE
DRIVE
PRE
DRIVE
RELAY
DRIVER
Q710
RELAY
DRIVER
Q809
R810
R811
F902
F901
JW905
JW903
DG600
S901
-3
-2
-1
J911
AC OUTLET
R910
RELAY
SWITCH
EXCEPT
E2 MODEL
EXCEPT
E2 MODEL
E2 MODEL
S901
240V
220V
120V
VOLTAGE
SELECTOR
B+ SWITCH
Q693-695
RELAY
DRIVER
Q800
• Signal path
: TUNER (FM/AM)
• R-ch is omitted due to
same as L-ch.
• Abbreviation
CND: Canadian mode
E2 : 120V AC area in E model
(Page 15)
All manuals and user guides at all-guides.com