Pioneer Elite Music Tap X-SMC4-K User manual

Operating Instructions
Mode d’emploi
Register your product at:
http://www.pioneerelectronics.com (US)
http://www.pioneerelectronics.ca (Canada)
http://www.pioneerelectronics.com (États-Unis)
http://www.pioneerelectronics.ca (Canada)
• Protect your new investment
The details of your purchase will be on file for reference in the event of an insurance claim such as loss or theft.
• Improve product development
Your input helps us continue to design products that meet your needs.
• Receive a free Pioneer newsletter
Registered customers can opt in to receive a monthly newsletter.
• Receive free tips, updates and service bulletins on your new product
X-SMC4-K
MUSIC TAP
“MUSIC TAP” is a registered trademark of PIONEER CORPORATION.
"MUSIC TAP" est une marque deposee de PIONEER CORPORATION.
X-SMC4_CUXZT_Cover_Anki.fm 1 ページ ２０１１年７月８日 金曜日 午後１時４１分

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
D8-10-1-2_A1_En
This Class B digital apparatus complies with
Canadian ICES-003.
D8-10-1-3_A1_En
Information to User
Alterations or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.
D8-10-2_A1_En
WARNING:Handling the cord on this product or
cords associated with accessories sold with the
product may expose you to chemicals listed on
proposition 65 known to the State of California and
other governmental entities to cause cancer and
birth defect or other reproductive harm.
Wash hands after handling.
D36-P5_B1_En
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
D3-4-2-1-3_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
WARNING
Before plugging in for the first time, read the following
section carefully.
The voltage of the available power supply diers
according to country or region. Be sure that the power
supply voltage of the area where this unit will be used
meets the required voltage (e.g., 230 V or 120 V) written
on the AC adapter label.
D3-4-2-1-4*_A1_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 10 cm at top, 10 cm at rear, and 10 cm at each
side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
D3-4-2-1-7c*_A1_En
IMPORTANT NOTICE
THE MODEL NUMBER AND SERIAL NUMBER OF THIS EQUIPMENT ARE ON THE REAR OR BOTTOM.
RECORD THESE NUMBERS ON YOUR ENCLOSED WARRANTY CARD AND KEEP IN A SAFE PLACE FOR FUTURE
REFERENCE.
D36-AP9-1_A1_En
X-SMC4_CUXZT_Cover_Anki.fm 2 ページ ２０１１年７月８日 金曜日 午後１時４１分

The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
%#76+10
4+5-1('.'%64+%5*1%-
&101612'0
IMPORTANT
D3-4-2-1-1_A1_En
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
Only use attachments/accessories specified by
the manufacturer.
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms
or when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
D3-7-13-69_En
11)
12)
13)
14)
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation). D3-4-2-2-2a*_A1_En
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left unused
for a long period of time (for example, when on
vacation). D3-4-2-2-1a_A1_En
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a
minimum distance of 20 cm between the radiator and
your body.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed and
operated with a minimum distance of 20 cm between the
radiator and your body.
X-SMC4_CUXZT_Cover_Anki.fm 3 ページ ２０１１年７月８日 金曜日 午後１時４１分

POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement.
S002*_A1_En
Radio wave caution
This unit uses a 2.4 GHz radio wave frequency, which is
a band used by other wireless systems (Microwave
ovens and Cordless phones, etc.). In this event noise
appears in your television image, there is the possibility
this unit (including products supported by this unit) is
causing signal interference with the antenna input
connector of your television, video, satellite tuner, etc.
In this event, increase the distance between the
antenna input connector and this unit (including
products supported by this unit).
• Pioneer is not responsible for any malfunction of the
compatible Pioneer product due to communication
error/malfunctions associated with your network
connection and/or your connected equipment.
Please contact your Internet service provider or
network device manufacturer.
• A separate contract with/payment to an Internet
service provider is required to use the Internet.
AC adapter CAUTION
• Make sure to grasp the body of the AC adapter when
removing it from the power outlet. If you pull the
power cord, it may become damaged which could
lead to fire and/or electrocution.
• Do not attempt to plug in or remove the AC adapter
with wet hands. This may result in electrocution.
• Do not insert the power cord of AC adapter into a
power outlet where the connection remains loose
despite inserting the prongs all the way into the
outlet. Heat may be generated which could lead to
fire. Consult with the retailer or an electrician
regarding replacement of the power outlet.
When using this product, confirm the safety
information shown on the bottom of the unit and the
AC adapter label. D3-4-2-2-4_B1_En
This transmitter must not be co-located or operated
in conjunction with any other antenna or transmitter.
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may
not cause interference, and (2) this device must
accept any interference, including interference that
may cause undesired operation of the device.
WARNING
Store small parts out of the reach of children and
infants. If accidentally swallowed, contact a doctor
immediately.
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period. K041_A1_En
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a
safe level – a level that lets the sound come through
clearly without annoying blaring or distortion and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time, your hearing
“comfort level” adapts to higher volumes of sound, so
what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by setting
your equipment at a safe level BEFORE your hearing
adapts.
ESTABLISH A SAFE LEVEL:
• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it
comfortably and clearly, without distortion.
• Once you have established a comfortable sound
level, set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING
GUIDELINES:
• Do not turn up the volume so high that you can’t
hear what’s around you.
• Use caution or temporarily discontinue use in
potentially hazardous situations.
• Do not use headphones while operating a motorized
vehicle; the use of headphones may create a traffic
hazard and is illegal in many areas.
S001a_A1_En
Store the AC adapter out of the reach of
children and infants.
The AC adapter cord may accidentally wind around the
neck and it may cause suffocation.
X-SMC4_CUXZT_Cover_Anki.fm 4 ページ ２０１１年７月８日 金曜日 午後１時４１分

5
En
English Français Español
Thank you forbuying this Pioneerproduct.
Please read through these operating instructions so that you will know how to operate yourmodel properly. Afteryou have
finished reading the instructions, put them in a safe place forfuture reference.
Contents
01 Before you start
What’s in the box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Loading the batteries in the remote control . . . . . . . . . .6
Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 6
02 Connections
Connecting the FM antenna. . . . . . . . . . . . . . . . . . . . . . .7
Connecting USB storage devices . . . . . . . . . . . . . . . . . .7
Connecting yourTV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Connecting to the network through the LAN
interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting using LAN cable . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting using wireless LAN. . . . . . . . . . . . . . . . . . . . . 8
Plugging in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
03 Part names and functions
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Toppanel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Main display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
04 Getting started
05 iPod/iPhone playback
Confirming what iPod/iPhone models are
supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Connecting youriPod/iPhone . . . . . . . . . . . . . . . . . . . .15
Connecting yourTV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Playing youriPod/iPhone . . . . . . . . . . . . . . . . . . . . . . . .16
06 Bluetooth ® Audio playback
Music playback using Bluetooth wireless
technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Remote control operation. . . . . . . . . . . . . . . . . . . . . . . . . 18
About Bluetooth® adapter. . . . . . . . . . . . . . . . . . . . . . .18
Setting the PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Pairing Bluetooth® adapterand Bluetooth wireless
technology device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Listening to music contents of Bluetooth wireless
technology device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
AIR JAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Radio wave caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Scope of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Radio wave reflections . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Precautions regarding connections to products
supported by this unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
07 USB playback
Playing files stored on USB storage devices. . . . . . . . .22
08 Internet radio
Listening to the Internet radio . . . . . . . . . . . . . . . . . . . .23
Connecting to a LAN network . . . . . . . . . . . . . . . . . . . . . 23
Listening to the Internet radio forthe first time . . . . . . . 23
Tune into a station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Adding the stations to the Favorites . . . . . . . . . . . . . . .24
To delete the stations from the list . . . . . . . . . . . . . . . . . 24
Advanced operations forthe Internet radio . . . . . . . . .24
Registering broadcast stations not on the vTunerlist
from the special Pioneersite . . . . . . . . . . . . . . . . . . . . . . 24
09 Music server
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
About playable DLNA network devices. . . . . . . . . . . . . . 25
Using AirPlay on iPod touch, iPhone, iPad and
iTunes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
About the DHCP serverfunction. . . . . . . . . . . . . . . . . . . 25
Authorizing this unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Playing audio files stored on PCs orother
components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Connecting to the LAN network . . . . . . . . . . . . . . . . . . . 26
Playback with Music Server. . . . . . . . . . . . . . . . . . . . . . . 26
10 Using the tuner
Listening to the FM radio broadcasts . . . . . . . . . . . . . .27
Saving stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Listening to station presets . . . . . . . . . . . . . . . . . . . . . .27
11 Other connections
Connecting auxiliary components . . . . . . . . . . . . . . . . .28
Listening to auxiliary components. . . . . . . . . . . . . . . . .28
12 Changing the settings
Using the timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Setting the wake-uptimer. . . . . . . . . . . . . . . . . . . . . . . . 30
Turning on/off the wake-uptimer. . . . . . . . . . . . . . . . . . 31
Using the wake-uptimer. . . . . . . . . . . . . . . . . . . . . . . . . 31
Using the sleeptimer. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Network setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Wired Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Wireless Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
WPS connection setting . . . . . . . . . . . . . . . . . . . . . . . . .33
Connecting using PIN Input . . . . . . . . . . . . . . . . . . . . . . 34
Friendly Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Parental lock setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Turn on/off the parental lock . . . . . . . . . . . . . . . . . . . . . . 34
Changing the password . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Software Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Software Update messages . . . . . . . . . . . . . . . . . . . . . . . 35
Sound settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Using the Virtual Surround/Sound Retriever. . . . . . . . . 35
Adjusting the bass and treble . . . . . . . . . . . . . . . . . . . . . 35
Resetting the system. . . . . . . . . . . . . . . . . . . . . . . . . . . .35
13 Additional information
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Playable file formats . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Cautions on use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
About network playback . . . . . . . . . . . . . . . . . . . . . . . . . 42
About iPod/iPhone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
About Wi-Fi® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
•Illustrations featured in the Operating Instructions may
have been modified orsimplified forease of explanation,
and may therefore differfrom the actual product
appearance.
X-SMC4_CUXZT_En.book 5 ページ ２０１１年７月７日 木曜日 午後３時３８分

Before you start01
6
En
Chapter 1:
Before you start
What’s in the box
Please confirm that the following accessories are in the box
when you open it.
• Remote control
•Powercord
• AC adapter
• FM wire antenna
• AAA batteries (R03) x 2
• Warranty card
• Operating instructions (this document)
Loading the batteries in the remote
control
1 Open the rear lid and load the batteries as
illustrated below.
2 Close the rear lid.
The batteries included with the unit are to check initial
operations; they may not last over a long period. We
recommend using alkaline batteries that have a longer life.
Caution
• When inserting the batteries, make sure not to damage
the springs on the battery’s terminals.
• Do not use any batteries other than the ones specified.
Also, do not use a new battery together with an old one.
• When loading the batteries into the remote control, set
them in the proper direction, as indicated by the polarity
marks (and ).
• Do not heat batteries, disassemble them, or throw them
into flames or water.
• Batteries may have different voltages, evenif they are the
same size and shape. Do not use different types of
batteries together.
• To prevent leakage of battery fluid, remove the batteries
if you do not plan to use the remote control for a long
period of time (1 month or more). If the fluid should leak,
wipe it carefully off the inside of the case, then insert new
batteries. If a battery should leak and the fluid should get
on your skin, flush it off with large quantities of water.
• When disposing of used batteries, please comply with
governmental regulations or environmental public
institution’s rules that apply in your country/area.
•WARNING
Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat,
explode or catch fire. It can also reduce the life or
performance of batteries.
Using the remote control
The remote has a range of about 7 m (23 ft.) at an angle of
about 30º from the remote sensor.
Keep in mind the following when using the remote control:
• Make sure that there are no obstacles between the
remote and the remote sensor on the unit.
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the unit’s
remote sensor.
• Remote controllers for different devices can interfere
with each other. Avoid using remotes for other
equipment located close to this unit.
• Replace the batteries when you notice a fall off in the
operating range of the remote.
30°
7 m (23 ft.)
30°
01_before_you_start.fm 6 ページ ２０１１年７月１１日 月曜日 午前１１時５分

Connections 02
7
En
English Français Español
Chapter 2:
Connections
•Besure to turn off the powerand unplug the powercord
from the poweroutlet whenevermaking orchanging
connections.
• Connect the powercord afterall the connections
between devices have been completed.
Connecting the FM antenna
Connect the FM antenna plug onto the centerpin of the FM
antenna socket.1
Connecting USB storage devices
Connecting your TV
To watch iPod/iPhone images on a television, connect it
using a composite video cable.
• When an iPod/iPhone is connected to this unit, the TV
output setting of the iPod/iPhone is automatically set to
‘ON’.2
Note
1Toensure optimum reception, make sure the FM antenna is fully extended and not coiled orhanging at the rearof the unit.
ANTENNA LAN
(10/100)
VIDEO
OUT
DC IN
19 V
FM75
FM wire antenna (supplied)
This unit’s rearpanel
USB storage device
(commercially available)
This unit’s front panel
2 • Some iPod allow the TV output setting to be changed while connected.
• When the iPod/iPhone is disconnected from this unit, the iPod/iPhone’s TV output setting returns to its original state.
ANTENNA LAN
(10/100)
VIDEO
OUT
DC IN
19 V
FM75
Yellow
TV
Video cable
(commercially available)
To video input
terminals
This unit’s rearpanel
X-SMC4_CUXZT_En.book 7 ページ ２０１１年７月７日 木曜日 午後３時３８分

Connections02
8
En
Connecting to the network through the
LAN interface
By connecting this unit to the network via the LAN interface,
you can play back audio files stored on components on the
network, including yourPC, and listen to Internet radio
stations.1
Connect the LAN terminal on this unit to the LAN terminal on
yourrouter(with orwithout the built-in DHCP serverfunction)
with a straight LAN cable (CAT 5 orhigher). Also wireless
connection to the network is possible.
Turn on the DHCP serverfunction of yourrouter. If yourrouter
does not have a built-in DHCP serverfunction, you have to set
upthe network manually. Fordetails, see page 31.
Connecting using LAN cable
Connecting using wireless LAN
Note
1•Touseservices such as Internet radio orautomatic clock sync functions, you must conclude a contract with an Internet service
provider.
• Photo orvideo files cannot be played back.
• With Windows Media Player11or12, you can even play back copyrighted audio files on this unit.
ANTENNA LAN
(10/100)
VIDEO
OUT
DC IN
19 V
FM75
WAN
321
LAN
Internet
Modem
Router
PC2
PC1
This unit’s rearpanel
LAN cable
(commercially
available)
WAN
321
LAN
Internet
This unit
Router
PC
Modem
X-SMC4_CUXZT_En.book 8 ページ ２０１１年７月７日 木曜日 午後３時３８分

Connections 02
9
En
English Français Español
Plugging in
Important
•Before making orchanging the connections, switch off
the powerand disconnect the powercord from the AC
outlet.
Afteryou’ve finished making all connections, plug the unit
into an AC outlet.
1 Plug the supplied AC adapter into the DC IN
socket on the back of the unit.
2 Plug the supplied power cord into the AC
adapter then plug the other end into an AC
outlet.
ANTENNA LAN
(10/100)
VIDEO
OUT
DC IN
19 V
FM75
To AC outlet
AC adapter
(supplied)
This unit’s rearpanel
Powercord (supplied)
X-SMC4_CUXZT_En.book 9 ページ ２０１１年７月７日 木曜日 午後３時３８分

Part names and functions03
10
En
Chapter 3:
Part names and functions
Remote control
1 STANDBY/ON
Press to turn the poweron and off.
2 DISP OFF
Press to turn the main display off when you do not need it.
3 Number buttons (0 to 9)
Use them to select the station preset when using the tuner,
etc.
4 SET UP
Use this to change the settings such as Timer Setting
(page 29), Clock Setting (page 29), Display Setting
(page 29), Network Setting (page 29), Option Setting
(page 30) and see System Info (page 30).
5MENU
Select and play the track orfile from the menu screen.
6///
Use these to select items, change settings and move the
cursor.
ENTER
Use this to implement the selected item orentera
setting that you have changed.
PRESET +/–
Use these to select station presets.
TUNE +/–
Change the frequency one stepat a time. To search for
stations automatically, press and hold forabout a few
second.
7 SOUND
Turns Virtual Surround and Sound Retriever on and off
(page 35). Also use to adjust the Bass and Treble.
8 FUNCTION /
Use to change the input source. The source changes as
below.
iPod BT Audio Air Jam USB FM Internet
Radio Music Server AUX Return to the
beginning (Undisplayed)
9  PLAY
Press to start playback.
10 
Press during playback to fast-reverse.
STANDBY/ON
5
6
12
1
3
7
15
2
4
8
X-SMC4_CUXZT_En.book 10 ページ ２０１１年７月７日 木曜日 午後３時３８分

Part names and functions 03
11
En
English Français Español
11 PREV
Press to return to the beginning of the currently playing track
orfile. Press twice to move back to the beginning of the
previous track orfile.
12 STOP
Press to stopplayback.
13 SLEEP
Use to put the unit in the sleepmode and select the amount
of time before sleep(page 31).
14
Use to turn on and off the timer(page 30).
15 CLEAR
Press to clearthe selected item.
Use this forexample if you input the wrong number.
16 RETURN
Press to return to the previous screen. Also, use to cancel the
clock setting orthe sound setting.
17 MUTE
Press to temporarily silence the sound.
18 SHUFFLE
Perform shuffle play of tracks on the selected iPod/iPhone,
USB storage device orMusic Server(page 16, 22, 26).
19 VOLUME +/–
Use to set the listening volume. (Default setting: 10)
20 REPEAT
Perform repeat play of tracks on the selected iPod/iPhone,
USB storage device orMusic Server(page 16, 22, 26).
21 
Press during playback to fast-forward.
22  PAUSE
Press to stopplayback temporarily. Press again to resume.
23 NEXT
Press during playback to skipahead to the beginning of the
next track orfile.
Top panel
1  STANDBY/ON
Press to turn the poweron and off.
2FUNCTION
Use to change the input source. The source changes as
below.
iPod BT Audio Air Jam USB FM Internet
Radio Music Server AUX Return to the beginning
(Undisplayed)
3 BT AUDIO
Switches the input source to BT Audio.
4 AIR JAM
Switches the input source to Air Jam.
5 
Press to start playback. During playback, pause/unpause
playback.
6 
Press to stopplayback.
7 VOLUME –/+
Use to set the listening volume. (Default setting: 10)
1 4 57
7
6
2 3
X-SMC4_CUXZT_En.book 11 ページ ２０１１年７月７日 木曜日 午後３時３８分

Part names and functions03
12
En
Front panel
1 POWER ON
When the poweris on, this indicatorlights.
BT AUDIO
When BT Audio is selected as the input source, this
indicatorlights.
AIR JAM
When Air Jam is selected as the input source, this
indicatorlights.
TIMER
When the wake-uptimeris set to On, this indicator
lights.
TUNE
When the tunerreceives FM broadcasts, the TUNE
indicatorlights.
2 Main Display
3 Sub Display
4 Speaker units
5 USB port
6 AUX IN
Use to connect auxiliary components.
7 PHONES
Use to connect headphones.
8 iPod/iPhone connector port
44
3
5677
8
21
X-SMC4_CUXZT_En.book 12 ページ ２０１１年７月７日 木曜日 午後３時３８分

Part names and functions 03
13
En
English Français Español
Main display
1 Input source
2 Sleep timer
When the sleeptimeris set, the remaining time until power
off is displayed.
3 AirPlay
This appears in blue during AirPlay operation, and in white
during stopmode.
4 Network connection status
When the unit is connected to the wired network, this
indicatorlights.
When the unit is connected to the wireless network, this
indicatorlights.1
When the unit is not connected to the network, this
indicatorlights.
5 Name of file/track/artist/album/station,
etc.
6Mute
Displayed during Mute operation.
7 Play status
8 Artwork
Displayed when the currently playing file includes an album
jacket image, etc.
9 Repeat and Shuffle
Repeat all files.
Repeat a file.
Shuffle
10 Elapsed playing time
11 Play bar
The barbecomes longertogetherwith the elapsed playback
time.
12 Remaining playing time
Song
Artist
Album
1 4
57
8
7
9
6
7
2 3
10 11 12
Note
1 This does not indicate the strength of the received signal; the numberof bars does not change.
X-SMC4_CUXZT_En.book 13 ページ ２０１１年７月７日 木曜日 午後３時３８分

Getting started04
14
En
Chapter 4:
Getting started
When you use the unit for the first time, the following screens
will be displayed.
Set up the following items to customize the unit.
1 Press STANDBY/ON .
About twenty seconds after turning on the power, the
following splash screen appears. About one minute is
required between turning the power on and completion of
startup.
Setting Quick Start Mode to On will allow faster startup
(page 30).
2 Cancel Demo Mode (Set to normal mode).
The screen below will automatically appear after the screen in
step 1. If the STOP is pressed, the operation will proceed to
step 3.
• Press PLAY button to start the Demo Mode. When
starting up the next time, it will be necessary to set step
3.
• When Demo Mode is selected, the Quick Start Mode
is simultaneously set to On.
•TheDemo Mode and Quick Start Mode settings can
also be changed manually in the Option Settings (see
page 30). When Demo Mode is set in step 2, if the
Option Settings menu is subsequently used to cancel
the Demo Mode, the Quick Start Mode will not be
cancelled simultaneously. The two settings must be
changed independently.
3Use / to select the menu language of this
unit, then press
ENTER .
The setting is done.
Select "Start" to start
Demo mode; otherwise
"Cancel".
[PLAY] Start
[STOP] Cancel
Language
Français
Deutsch
Nederlands
English
04_Getting_started.fm 14 ページ ２０１１年７月８日 金曜日 午後１時３７分

iPod/iPhone playback 05
15
En
English Français Español
Chapter 5:
iPod/iPhone playback
Merely by connecting youriPod/iPhone to this unit, you can
enjoy high-quality sound from youriPod/iPhone. This unit can
also be connected to a television set, letting you view images
from youriPod/iPhone.
Playback and volume level setting foriPod/iPhone music and
images can be performed from this unit orthe iPod/iPhone
itself.
Confirming what iPod/iPhone models are
supported
The iPod/iPhone playable on this unit are shown below.1
* The iPod nano 6G cannot play back video, but can play slide
shows only.
• This system has been developed and tested forthe
software version of iPod/iPhone indicated on the website
of Pioneer(http://pioneer.jp/homeav/support/ios/
na/).
• Installing software versions otherthan indicated on the
website of Pioneerto youriPod/iPhone may result in
incompatibility with this system.
1 Select “ Settings ” from the top menu.
When using iPod touch oriPhone, select “General” after
selecting “Settings”.
2 Select “ About ”.
The software version will be displayed.
Tip
• When using an iPod/iPhone not supported by this unit,
use a commercially available cable to connect the iPod/
iPhone to the AUX IN connectorof this unit.
Connecting your iPod/iPhone
Caution
• When connecting iPod/iPhone units, always use the
dock adapterprovided with iPod/iPhone units, ora
commercially available adapterdesigned to support
iPod/iPhone. The iPod/iPhone cannot be connected
without a dock adapter; attempting to connect an iPod/
iPhone without it will cause damage ormalfunction.
• An iPod/iPhone universal dock adapteris not supplied
with this unit.
1 Open the iPod/iPhone connector port.
2
2 Attach the dock adapter to iPod/iPhone
connector port.
When attaching the dock adapter, be sure to orient the front-
back directions of the dock adaptercorrectly. To attach, first
place the protruding tabs on the front side of the adapterinto
the depressions on the iPod/iPhone connectorport and press
into position. When attaching the adapter, be careful not to
strike the connectors.
iPod/iPhone Audio Control Video
iPod nano 2G —
iPod nano 3/4/5/6G *
iPod classic 
iPod touch 1/2/3/4G 
iPhone 
iPhone 3G/3GS 
iPhone 4 
Note
1•Pioneerdoes not guarantee that this unit plays iPod/iPhone models otherthan the ones specified.
• Some functions may be restricted depending on the model orsoftware version.
• iPod/iPhone is licensed forreproduction of non-copyrighted materials ormaterials the useris legally permitted to reproduce.
• Features such as the equalizercannot be controlled using this system, and we recommend switching the equalizeroff before
connecting.
• Pioneercannot underany circumstances accept responsibility forany direct orindirect loss arising from any inconvenience orloss of
recorded material resulting from iPod/iPhone failure.
• Fordetailed instructions on using the iPod/iPhone, please referto the manual supplied with the iPod/iPhone.
2 When opening orclosing the iPod/iPhone connectorport, support the topof the unit with yourhand to prevent it from moving.
Push
X-SMC4_CUXZT_En.book 15 ページ ２０１１年７月７日 木曜日 午後３時３８分

iPod/iPhone playback05
16
En
3 Connect your iPod/iPhone.
• When youriPod/iPhone is not connected to the unit,
close the iPod/iPhone connectorport firmly.
Connecting your TV
To watch iPod/iPhone images on a television, connect it using
a composite video cable.
• When an iPod/iPhone is connected to this unit, the TV
output setting of the iPod/iPhone is automatically set to
‘ON’.1
Playing your iPod/iPhone
Caution
• When youriPod/iPhone is connected to this unit and you
wish to operate the iPod/iPhone directly, be sure to hold
the iPod/iPhone steady with the otherhand to prevent
malfunctions due to faulty contacts.
1 Connect your iPod/iPhone.
• To connect youriPod/iPhone, see Connecting your iPod/
iPhone on page 15.
2 Press FUNCTION / to select iPod as the
input source.
iPod is shown on the main display and starts playback.
The following operations are possible foriPod/iPhone.
*Each time you press REPEAT the repeat modes changes as
below.2
Repeat 1  Repeat all  Normal playback
Repeat 1: Repeats a file currently played back.
Repeat all: Repeats all files.
When no device is connected to the iPod/iPhone connector
port and this unit is not operated for30 minutes ormore,
powerwill automatically turn off.3
Note
1 • Some iPod allow the TV output setting to be changed while connected.
• When the iPod/iPhone is disconnected from this unit, the iPod/iPhone’s TV output setting returns to its original state.
MENU


3
2
Push
Button What it does
PLAY Starts normal playback.
PAUSE Pauses playback.
STOP Pauses playback.
PREV Press to skipto the start of the current file, then
previous files.
NEXT Press to skipto the next file.
 Press and hold to start fast reverse scanning.
 Press and hold to start fast forward scanning.
SHUFFLE The currently selected iPod/iPhone tracks are
played back in random order(shuffle play).
REPEAT The currently selected iPod/iPhone tracks are
played back repeatedly. *
MENU Use to access the iPod/iPhone menu.
//ENTER Use to control the iPod/iPhone menu.
2 No icon will be displayed on the main display when the iPod/iPhone is in the repeat mode orshuffle mode.
3OnlywhenPower Save mode is selected in Auto mode select (page 30).
X-SMC4_CUXZT_En.book 16 ページ ２０１１年７月７日 木曜日 午後３時３８分

iPod/iPhone playback 05
17
En
English Français Español
Important
If this unit cannot play youriPod/iPhone, perform the
following troubleshooting checks:
• Check whetherthe iPod/iPhone is supported by this unit.
• Reconnect the iPod/iPhone to the unit. If this doesn’t
seem to work, try resetting youriPod/iPhone.
• Check the iPod/iPhone software is supported by this
unit.
If the iPod/iPhone cannot be operated, check the following
items:
• Is the iPod/iPhone connected correctly? Reconnect the
iPod/iPhone to the unit.
• Is the iPod/iPhone experiencing a hangup? Try resetting
the iPod/iPhone, and reconnect it to the unit.
Tip
• iPod/iPhone recharging occurs wheneveran iPod/
iPhone is connected to this unit. (This function is
supported in standby mode as well.)
• When input is switched from iPod to anotherfunction,
iPod/iPhone playback is temporarily stopped.
X-SMC4_CUXZT_En.book 17 ページ ２０１１年７月７日 木曜日 午後３時３８分

Bluetooth
®
Audio playback
06
18
En
Chapter 6:
Bluetooth
®
Audio playback
Music playback using Bluetooth wireless
technology
When the Bluetooth®adapter(PioneerModel No. AS-BT200)
is connected to this unit, a product equipped with Bluetooth
wireless technology (portable cell phone, digital music player,
etc.) can be used to listen to music wirelessly.1Also, by using
a commercially available transmittersupporting Bluetooth
wireless technology, you can listen to music on a device not
equipped with Bluetooth wireless technology. The AS-BT200
model supports SCMS-T contents protection, so music can
also be enjoyed on devices equipped with SCMS-T type
Bluetooth wireless technology.
Remote control operation
The remote control supplied with this unit allows you to play
and stopmedia, and perform otheroperations.2
About Bluetooth
®
adapter
Located in the position shown in the accompanying
illustration. Do not remove.
Remote control operation
This unit
Device not equipped with Bluetooth
wireless technology:
Digital music player
+
Bluetooth®audio transmitter
(commercially available)
Bluetooth wireless technology
enabled device:
Digital music player
Bluetooth wireless technology
enabled device:
Cell phone
Note
1•TheBluetooth wireless technology enabled device must support A2DP profiles.
• Pioneerdoes not guarantee properconnection and operation of this unit with all Bluetooth wireless technology enabled devices.
• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by PIONEER
CORPORATION is underlicense. Othertrademarks and trade names are those of theirrespective owners.
2•TheBluetooth wireless technology enabled device must support AVRCP profiles.
• Remote control operations cannot be guaranteed forall Bluetooth wireless technology enabled devices.
Bluetooth®
adapter
This unit’s
rearpanel
Cover
X-SMC4_CUXZT_En.book 18 ページ ２０１１年７月７日 木曜日 午後３時３８分

Bluetooth
®
Audio playback 06
19
En
English Français Español
Setting the PIN code
Set this unit’s PIN code to the same setting as that forthe
Bluetooth wireless technology device used. Supported PIN
code setting values include 0000, 1234 or8888.
• Default setting: 0000
1 Press FUNCTION / or BT AUDIO on the
top panel of the unit to select
BT Audio as the
input source.
The BT AUDIO indicatorlights and BT Audio is shown on the
main display.
2 Press SET UP .
3Use
/ to select Option Settings  BT PIN
Select, then press
ENTER .
4Use
/ to select the PIN code, then press
ENTER .
The PIN code is stored.
Pairing Bluetooth
®
adapter and
Bluetooth wireless technology device
“Pairing” must be done before you start playback of Bluetooth
wireless technology content using Bluetooth®adapter. Make
sure to pairdevices the first time you operate the system or
any time pairing data is cleared. “Pairing” is the step
necessary to registerBluetooth wireless technology device to
enable Bluetooth communications.1Formore details, see
also the operating instructions of yourBluetooth wireless
technology device.
1 Press FUNCTION / or BT AUDIO on the
top panel of the unit to select
BT Audio as the
input source.
The BT AUDIO indicatorlights and BT Audio is shown on the
main display.
2 Turn on the Bluetooth wireless technology
device that you want to pair, place it near the
system and set it into pairing mode.
Pairing starts.
3 Check to see that the Bluetooth
®
adapter is
detected by the
Bluetooth wireless technology
device.
•IftheBluetooth wireless technology device cannot be
connected to the unit, perform the connection operation
from the Bluetooth wireless technology device.
Listening to music contents of Bluetooth
wireless technology device
1 Press FUNCTION / or BT AUDIO on the
top panel of the unit to select
BT Audio as the
input source.
The BT AUDIO indicatorlights and BT Audio is shown on the
main display.
2 Make connection between the Bluetooth
wireless technology device and the unit.
•SeePairing Bluetooth® adapter and Bluetooth wireless
technology device above.
Option Setting
Volume Limit Setting
Internet Parental Lock
AutoMode Change
BT PIN Select
Note
1•Pairing is required when you first use Bluetooth wireless technology device and Bluetooth®adapter.
• To enable Bluetooth communication, pairing should be done with both of yoursystem and Bluetooth wireless technology device.
• During pairing, the name of this unit appears as AS-BT200.
X-SMC4_CUXZT_En.book 19 ページ ２０１１年７月７日 木曜日 午後３時３８分

Bluetooth
®
Audio playback
06
20
En
3 Press PLAY to start playback.
The following operations are now possible forBluetooth
wireless technology devices, using the remote control.1
* This function may work differently depending on the connected
device.
• When no Bluetooth wireless technology device is
connected and no operation has been done for30
minutes ormore, the powerwill automatically turn off.2
AIR JAM
AirJam – a Pioneer-exclusive application and available for
free.
AirJam lets you connect multi compatible devices to this unit
using Bluetooth wireless technology. With it, you can make a
groupplaylist directly on a supported device to play in your
home theaterthrough the unit. You and yourfriends can add
songs from yourdevices to the playlist. Also AirJam lets you
delete the song before anyone has to hearit.
1 Press FUNCTION / or AIR JAM on the top
panel of the unit to select
Air Jam as the input
source.
The AIR JAM indicatorlights and Air Jam is shown on the
main display.
Formore details on using AirJam, access ourwebsite.
http://pioneer.jp/product/soft/iapp_airjam/en.html
Radio wave caution
This unit uses a 2.4 GHz radio wave frequency, which is a
band used by otherwireless systems (see list below). To
prevent noise orinterrupted communication, do not use this
unit nearby such devices, ormake sure these devices are
switched off during use.
•Cordless phones
•Cordless facsimiles
•Microwave ovens
•Wireless LAN devices (IEEE802.11b/g)
•Wireless AV equipment
•Wireless controllers forgame systems
•Microwave-based health aids
• Some baby monitors
Other, less common, equipment that may operate on the
same frequency:
• Anti-theft systems
•Amateurradio stations (HAM)
•Warehouse logistic management systems
•Discrimination systems fortrain oremergency vehicles
Note
• In the event noise appears in yourtelevision image, there
is the possibility that a Bluetooth wireless technology
enabled device orthis unit (including products
supported by this unit) are causing signal interference
with the antenna input connectorof yourtelevision,
video, satellite tuner, etc. In this event, increase the
distance between the antenna input connectorand the
Bluetooth wireless technology enabled device orthis
unit (including products supported by this unit).
•Ifthere is something obstructing the path between this
unit (including devices supported by this unit) and the
device equipped with Bluetooth
wireless technology
(such as a metal door, concrete wall, orinsulation
containing tinfoil), you may need to change the location
of yoursystem to prevent signal noise and interruptions.
Button What it does
PLAY Starts normal playback.
PAUSE Pauses playback.
STOP Stops playback.
PREV Press to skipto the start of the current file, then
previous files.
NEXT Press to skipto the next file.
 Press and hold to start fast reverse scanning. *
 Press and hold to start fast forward scanning. *
Note
1•TheBluetooth wireless technology enabled device must support AVRCP profiles.
• The operation of some Bluetooth wireless technology devices may differfrom what is shown in the above table.
2OnlywhenPower Save mode is selected in Auto mode select (page 30).
X-SMC4_CUXZT_En.book 20 ページ ２０１１年７月７日 木曜日 午後３時３８分