Pipe Decor 365 4TIER User manual

Parts List:
D - 1/2” ELBOW (4 PCS)
A - 1/2” FLANGE (10 PCS)
B - 1/2” X 6” CONNECTOR (2 PCS)
F - #10 X 1-3/4” SCREWS (40 PCS)
G - PLASTIC WALL ANCHORS
(40 PCS) NOTE: Use wall anchors for
hollow wall application only. Wall
anchors are not necessary if
flanges are attached directly to studs.
C - 1/2” X 12” CONNECTOR (16 PCS)
E - 1/2” TEE (6 PCS)
1.
12” PIPE (C)
1/2” FLANGE (A)
1/2” FLANGE (A)
1/2” FLANGE (A)
1/2” FLANGE (A)
1/2” FLANGE (A)
12” PIPE (C)
12” PIPE (C)
12” PIPE (C)
12” PIPE (C)
12” PIPE (C)
12” PIPE (C)
12” PIPE (C)
6” PIPE (B)
1/2” ELBOW (D)
1/2” TEE(E)
1/2” TEE (E)
1/2” TEE (E)
1/2” ELBOW (D)
PREPPING THE PIPE
VERY IMPORTANT: These are all authentic malleable iron
and require necessary cleaning and prepping; do not skip
this step.
1. Clean and dry all the parts with gentle soap.
2. Use a lint-free rag to apply metal polish to the parts.
3. Use metal polish or clear coat paint to seal the dry pipe.
RECOMMENDED
DRILL WITH 1/8” BIT
FOR WALL ANCHOR
RECOMMENDED
STUD FINDER
STUD
RECOMMENDED TOOLS
365 4TIER
THANK YOU SO MUCH FOR PURCHASING A PIPE DECOR PRODUCT. IF YOU HAVE ANY TROUBLE PUTTING YOUR KIT
TOGETHER OR MISSING PIECES PLEASE CONTACT [email protected] FOR ANY HELP AND RETURNS.

12:00
6:00
3:009:00
2.
1. Assemble the shelf bracket as shown in the picture. Hand tighten
all connections. be sure that all flange holes are in the 12:00, 3:00,
6:00 and 9:00 position.
2. Set the assembled brackets side by side with the face of the flanges
on a smooth, flat surface. See figure to the right. Make sure all flanges
line up evenly side by side, this will help to assure your shelves on both
sides are even. If flanges do not line up, adjust pipe accordingly by
tightening or loosening.
3. Make sure all flange faces are touching the flat surface evenly, this will
assure that there are no gaps between any of the flanges on the wall.
If flanges are not touching flat surface evenly, adjust accordingly by
tightening or loosening flanges.
NOTE: For best results, tiered shelf should be installed into a stud.
INSTALLATION:
ADJUST ALL FLANGES TO BE LEVEL AGAINST FLOOR

16” or 32”
3.
4. It is strongly recommended that the brackets are
fastened to wall studs or a wood/metal backing
plate. Studs are 1 1/2” wide and are generally
16” apart. The bracket assemblies need
to be either 16” or 32” apart. Locate and mark the
center of the studs with a stud finder (not included).
5. Place bracket assembly against the wall in the
desired location, with the top hole of the flange set
in the center of the stud. Mark the hole with a pencil.
Now mark the bottom hole of the bottom flange. Place
a level between the top mark and the bottom mark.
Adjust position of the bottom mark so it is vertically
level with the top hole mark.
Stud
6. Using a level, mark the top hole for the other
bracket assembly in the center of the stud where it
will be installed. This mark needs to be level with the
first top hole mark. Mark the bottom hole the same
way; level with the first bottom hole mark.
Stud Stud
STUD
BOOP!

*Wall Anchor Installation
1 2 3
1/8” Pilot Hole
7. Hold the bracket assembly against the wall with the top and bottom mark
lined up in the flange holes. Mark the remaining flange holes with a pencil.
(NOTE: It is mandatory to use all 12:00 and 6:00 positioned flange holes to
attach bracket to studs).
8. Drill a 1/8” pilot hole for all center hole marks (12:00 and 6:00
positions). Using a screwdriver (not included), screw the anchors
into the 3:00 and 9:00 positioned marks. See Illustration illustration
for wall anchor installation.
9. Install fully assembled bracket assemblies onto the wall with provided screws.
Stud
12:00
6:00
3:00
9:00