PipeBurst Pro RS500 Application guide

RS500 Device User Manual
Basic Overview
The primary function of an RS500 Device is enabling wireless operation of equipment wired to it.
The RS Device operates as a control module for standard PipeBurst Pro 5 equipment including the
WaterValve and FloMeter.
Customer Support
GreenField Direct, LLC
14015 238th Street
Greenwood, NE 68366
www.pipeburstpro.com/contact
E-Mail: help@greenfielddirect.com
Phone: 866-466-LEAK (5325)
Hours of Operation: Weekdays 8:00 AM –5:00 PM CT
©2021 GreenField Direct, LLC
rev.4.15.2021
RS500 Device Features
Warranty Information
PipeBurst Pro Products 2/5/7 Year Limited
Warranty
Please visit:
www.pipeburstpro.com/warranty to review full
warranty details
Insert Device
Image
Dimensions 4-1/8” W x 4-3/4” H x 1-1/4” D
Power Source AC Power Adapter
Built-in Sensors Ambient Air Temperature Sensor
Tamper Alert Sensor
Voltage 5 VDC
Housing Black ABS Plastic
Audible
Notification Internal Speaker
Wireless
Frequency 915 MHz
Input 1 & 2
Options WaterValve
FloMeter

Installation and Operation of an RS500 Device
Device association to a Gateway
1. On your ionleaks dashboard, go to the device tab and select add new device.
2. Enter in the device ID and device key for the RS500 and click add. Repeat this step for each sensor that
needs to be added before proceeding to step 3.
3. Power on the device with the provided 5 VDC power supply.
RS500 Device Placement
1. Place an RS500 Device at the desired location.
2. Complete any necessary wiring of hardware components to the RS500.
3. Apply AC power to the RS500 device with the provided adapter.
4. Once an RS Device is in its desired location and running on AC power, press and release the relay button on
the side of the RS to ensure functionality.
RS Device Standard Settings Summary
Warnings and Precautions
•RS Devices operate on communications frequencies which are subject to FCC rules and regulations.
Specific information about device conformity can be found at: https://www.pipeburstpro.com/disclaimers/
•Placing RS Devices near large metal objects may decrease or block wireless coverage.
•End User is responsible that the RS Device functionality and installation meets the desired requirements.
•This manual may be updated or changed without advanced notice
•To learn about changing settings via ionleaks.com, refer to the ionleaks.com User Manual.
Wireless Regulatory Information
Model: RS500
FCC ID: NCM-RS500
IC: 2734A-RS500
Frequency Range: 915 MHz
Maintenance Tips for Optimal Device Performance
•Clean RS500 Device housing, on a regular basis, with a damp cloth.
Setting Description
WaterValve WaterValve Mode gives feedback and control for connected WaterValves
.
A WaterValve Can be controlled locally via the pushbutton on the side of
the RS500.
FloMeter
FloMeter Mode allows an RS500 to read and report FloMeter data to
Ionleaks.com. Users can set custom flow thresholds using Ionleaks.com to
alert if abnormal flow is detected. Ionleaks.com is required for FloMeter
functionality.
Tamper Alert If the lid of the sensor is removed, a tamper alert is triggered.
Data Recording Interval The sensor is set to check-
in with the system at a user determined amount
of time.

RS500 Device Wiring Diagrams
LED Function On Off
1 Power Power On Power Off
2 Radio Radio
transmitting Sleep
3 Input 1 Input Closed Input Open
4 Relay 1 (NC) Relay Open Relay Closed
5 Input 2 Input Closed Input Open
6 Relay 2 (NC) Relay Open Relay Closed

RS Device Wiring Diagrams
Key Components
5VDC
in
Relay
button
Wire
Management
Compartment
Wire Terminals

RS Device Wiring Diagrams
WaterValve - Control + Feedback
IN 1 RLY 1
SIG: Green COM: Red
GND: Black NC: White
If using two WaterValves, repeat wiring for
Input 2 / Relay 2

RS Device Wiring Diagrams
FloMeter
IN 2
SIG: Green
GND: Black
If using two FloMeters, repeat wiring for Input 1

FCC §15.19 Labelling requirements
This device complies with part 15 of the FCC Rules and Innovation, Science and Economic Development Canada (ISED) license-
exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC §15.21 Information to user
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
FCC §15.105 statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Requirements
To comply with FCC RF exposure compliance requirements, the device must be installed to provide a separation distance of at least
20 cm from all persons.
ISED CANADA Statements
Le présent appareil est conforme aux CNR d' Innovation, Sciences et Développement économique Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Canada Class B statement
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
RF Exposure Requirements
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20 cm between the radiator and your body.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements du Canada établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
RS500 FCC-ISED Declaration
Popular Gateway manuals by other brands

WELLTECH
WELLTECH 3701 - RELEASE NOTE V106A release note

SMC Networks
SMC Networks D3G0804W user manual

ADTRAN
ADTRAN jobAid+ Total Access 324 manual

LV switch
LV switch IAD Series user manual

SMC Sierra Monitor
SMC Sierra Monitor FieldServer FS-8704-23 Driver manual

Mediatrix
Mediatrix 4102S Hardware installation guide