Yeastar Technology NeoGate TA3200 Safety guide

How to Connect Trixbox to
NeoGate TA FXS Gateway
Version 1.0
Date: 2014.06.06
Yeastar Information Technology Co. Ltd

How to Connect Trixbox to NeoGate TA FXS Gateway
2/15
Table of Contents:
1. Introduction......................................................................................... 3
2. Preparation ..........................................................................................3
3. VoIP Mode............................................................................................ 4
4. SPS/SPX Mode .....................................................................................8

How to Connect Trixbox to NeoGate TA FXS Gateway
3/15
1. Introduction
This application note shows how to connect Trixbox to NeoGate TA FXS gateway.
This guide has been tested with NeoGate TA3200 and Trixbox firmware version:
2.8.0.4.
Two modes are available for NeoGate TA to connect to Trixbox, we call them
VoIP trunk mode and Service Provider SIP/IAX trunk mode (SPS/SPX).
*You can simply choose one mode to achieve the connection.
Target：
After connecting NeoGate TA3200 and Trixbox, FXS extensions will be extended
on Trixbox. Once the FXS ports are connected to Trixbox, the phones connected
to the FXS ports will be treated as Trixbox FXS extensions. The following
features can be achieved:
1. Make calls between the analog phone and Trixbox SIP extension;
2. Receive incoming calls on the analog phones;
3. Make external calls from the analog phones using trunks on Trixbox.
Description：
IP address of Trixbox: 192.168.5.236
IP address of NeoGate TA3200: 192.168.5.13
Figure 1. Connect Trixbox and NeoGate TA3200
2. Preparation
NeoGate TA3200 attempts to contact a DHCP server in your network to obtain

How to Connect Trixbox to NeoGate TA FXS Gateway
4/15
valid network settings (e.g., the IP address, subnet mask, default gateway
address and DNS address) by default.
Before connect NeoGate TA3200 to Trixbox, you need to set a static IP address
from the same LAN with the Trixbox.
Steps to set static IP for NeoGate TA3200:
1. Connect one analog phone in one of the FXS ports on NeoGate TA3200;
2. Dial "***" to enter the voice menu;
3. Press "1" to check the IP address;
4. Open the browser and type in the TA3200's IP address to access TA3200;
5. Log in TA3200 and go to System→Network Preferences→LAN Settings,
disable DHCP and configure the LAN network, save and apply the changes,
reboot NeoGate TA3200 to take effect.
Figure 2. Configure LAN Settings on NeoGate TA3200
3. VoIP Mode
If you choose VoIP mode, the FXS ports will be registered as the Trixbox's SIP
extensions, which possess the same functions as other SIP extensions on

How to Connect Trixbox to NeoGate TA FXS Gateway
5/15
Trixbox.
Figure 3. Connect TA3200 and Trixbox via VoIP Mode
Step 1. Create a SIP extension on Trixbox.
Path: PBX→Extensions→Add Extension
Create an extension on Trixbox for the FXS port on the TA3200 which has
connected an analog phone. Here we take extension 300 for example.

How to Connect Trixbox to NeoGate TA FXS Gateway
6/15
Figure 4. Create Extension 300 on Trixbox
Step 2. Configure one VoIP server template on NeoGate TA3200.
Path: Gateway→VoIP Settings→VoIP Server Settings
Check "Enable Register", fill in the Trixbox's IP address, this VoIP server
template will be a VoIP mode template.
Figure 5. Configure the VoIP Server Template as VoIP Mode
Server Name: Tr i x bo x
Type: SIP
Enable Register: checked
Transpo r t: UDP
Hostname/IP: fill in the Trixbox IP address, 192.168.5.236
Domain: fill in the Trixbox IP address, 192.168.5.236
Step 3. Edit the Dial Pattern Template
Path: Gateway→VoIP Settings→VoIP Server Settings
The default dial pattern is set as ".", which allows you to dial any number out. In
this guide, we will remain the default setting. You can change it according to
your environment.

How to Connect Trixbox to NeoGate TA FXS Gateway
7/15
Figure 6. Edit Dial Pattern Template
Step 4. Edit the FXS port
Path: Gateway→FXS Port List→FXS Port List
Figure 7. Edit the FXS Port
Number: the extension number as the one you created on Trixbox, 300.
Primary Server: choose Trixbox(1), the VoIP server template configured in
Step 2.
User Name: the extension username on Trixbox, 300.
Authentication Name: the extension authentication name on Trixbox, 9000.
Password: the authentication password of the extension on Trixbox,
pincode9000.
Dial Pattern Template: Choose the Dial Pattern Template,
DialPatternTemplate1(1).
Save and apply the changes, and you will see the port status is “Registered” on
"Port Status" page.
Path: Status→System Status→Port Status

How to Connect Trixbox to NeoGate TA FXS Gateway
8/15
Figure 8. Port Status
Now, you are able to use the analog phone which is connected to NeoGate TA's
FXS port 1 to make calls and receive calls.
Note: Outgoing calls to Trixbox extensions and to external numbers through
trunks on Trixbox all should match the dial pattern, or calls will be failed.
4. SPS/SPX Mode
If you choose this mode to connect NeoGate TA3200 and Trixbox, the FXS port
will be registered as a Service Provider SIP/IAX (SPS/SPX) trunk to the Trixbox.
One SPS/SPX trunk to NeoGate TA also should be created on Trixbox. In this
guide, we use SIP protocol, configure one VoIP server template as SPS mode on
NeoGate TA3200 and create one Service Provider SIP trunk on Trixbox.
Figure 9. Connect TA3200 and Trixbox via SPS Mode

How to Connect Trixbox to NeoGate TA FXS Gateway
9/15
Step 1. Create a Service Provider SIP Trunk on Trixbox
Path: PBXTrunksAdd SIP Trunk
Figure 10. Add SIP Trunk

How to Connect Trixbox to NeoGate TA FXS Gateway
10/15
Figure 11. Configure SIP Trunk
PEER Details:
host=192.168.5.13
type=peer
qualify=yes
disallow=all
context=from-trunk
allow=ulaw,alaw,gsm
After creating the SIP trunk, we can check the status of this trunk, it should be
OK.
Path: PBXPBX SettingsToolsSystem AdministrationAsterisk CLI
Enter the command “sip show peers” and click “Execute”, the status will be

How to Connect Trixbox to NeoGate TA FXS Gateway
11/15
seen.
Figure 12. SIP Trunk Status
Step 2. Edit one VoIP Server template as SPS mode.
Path: Gateway→VoIP Settings→VoIP Server Settings
Do not check "Enable Register", choose SIP protocol, and fill in the Trixbox IP
address, the VoIP server template will be configured as SPS mode.
Figure 13. Configure the VoIP Server Template as SPS Mode
Server Name: Trixbox
Type: SIP
Enable Register: DO NOT check
Transport: UDP
Hostname/IP: fill in Trixbox's IP address, 192.168.5.236
Domain: fill in Trixbox's IP address, 192.168.5.236

How to Connect Trixbox to NeoGate TA FXS Gateway
12/15
Step 3. Edit the Dial Pattern Template
Path: Gateway→VoIP Settings→VoIP Server Settings
The default dial pattern is set as ".", which allows you to dial any number out. In
this guide, we will remain the default setting. You can change it according to
your environment.
Figure 14. Edit the Dial Pattern Template
Step 4. Edit the FXS port
Path: Gateway→FXS Port List→FXS Port List
Figure 15. Edit the FXS Port
Number: set a number for the FXS port. The number should be different from
the extension numbers on Trixbox. Here we set number 100 for FXS port 1.
Primary Server: choose Trixbox(1), the VoIP server template configured on
Step 2.

How to Connect Trixbox to NeoGate TA FXS Gateway
13/15
Dial Pattern Template: choose the Dial Pattern Template,
DialPatternTemplate1(1).
Note: You don't need to fill in any authentication name and authentication
password on the FXS port edit page if you choose SPS/SPX mode.
After saving and applying the changes, you will see the trunk is “OK” in “Line
Status”.
Path:StatusSystem StatusPort Status
Figure 16. FXS Port Status
Step 5. Create an inbound route on Trixbox.
Path: PBX→PBX Settings→Inbound Call Control→Inbound Routes
Choose the inbound destination as IVR, when you call in Trixbox from NeoGate
TA3200, you will hear the IVR prompt. The inbound route configured here
match DID number 9999, users from NeoGate TA3200 should dial 9999 to reach
Trixbox.

How to Connect Trixbox to NeoGate TA FXS Gateway
14/15
Figure 17. Add Incoming Route

How to Connect Trixbox to NeoGate TA FXS Gateway
15/15
Step 5. Create one outbound route on Trixbox.
To make calls from Trixbox to NeoGate TA3200, you need to create one
outbound route on Trixbox.
Path: PBX→PBX Settings→Outbound Routes→Add Route
Figure 18. Add Outbound Route
Set the dial pattern as X., choose the trunk "NeoGate_TA3200" which is created
above. In this guide, you should dial 100 to call the phone which is connected to
TA3200 FXS port 1.
<End>