Pisector GS08 User manual

PiSector GSM Cellular
Wireless Alarm System
User Manual ( GS08 )
Read manual fully before use.
PiSector Inc., USA, www.pisector.com

Welcome to PiSECTOR
Thank you for choosing PiSECTOR. Everyone at PiSECTOR is committed to giving you the best
home security available today and we want you to know that we take the safety of your home
and family seriously!
PiSECTOR was first developed a personal monitoring system to have state-of-the art home
protection at an affordable cost and now we're one of the fastest-growing security companies in
the industry.
PiSECTOR offers you the Ademco Protocol Security System. We've put complete control of your
security system in your hands anytime, from anywhere in the world.
PiSECTOR allows you to instantly arm and disarm your system, change your system settings,
find out your home security system’s status and so much more.
We encourage you to change the default password as soon as you get your system set up. You
won't find anything like PiSECTOR at any of those other security companies with all the
functions we designed for you at an affordable price.
This guide will walk you through the easy set up of your PiSECTOR system no matter which one
you ordered. We've started with already customizing and tuning your system to your
specifications, so everything is ready to go when you open the box. As soon as you're done, be
sure you register with PiSECTOR.com for any tech support in the future.
Again, thank you for being a PiSECTOR customer. We're doing everything we can to make sure
your home and family is safe.
Sincerely
PiSector Inc.

System Components
Console Panel
Program: press this key then input password, you
can enter program status (default password 888888 )
Arm: press this key and input password, you can
activate your system as Away from home
Disarm: press this key and input password, you can
deactivate your system
Chime: press this key you will see icon on LCD
screen, that means you have enabled your Chime
function, ( to make it work if you go to Sensor-Edit and
set your door sensor for Chime zone as Yes, you will
hear a music bell sounds when you open your door)
Home:press this key and input password, you can
active your system as Stay Home( if you go to Sensor-
Edit and set part of sensors for Home zone as No, when
you press Home, that sensor will disable, and all other sensors still enable)
Emergency:press this key and it will trigger your alarm system 24/7 anytime regardless of your system is armed or disarmed.
TALK/END:You can input your phone number directly then press this key to make a call or end a calling (only work with SIM card)
Scroll Key: press this key to page up and down to move and select menu list for functions, you also can use this key to find last 30 alarm
events during System Disarm Status.
Function keys:
Search: when you see an icon display on LCD screen, you can press “Search”to find existing events
Back: use to exit the last step during programing
Enter: for confirm your information
Mute: to quiet the entire key sounds
Vol+/Vol-: for adjusting the consoles sound volumes
Connect console Panel:
Put the console near your phone cord
Remove the table stand and cover on back side of console
Remove the SIM card cover
SIM Card Slot: Please pay attention to the direction arrow marked on the slot: “LOCK” / “OPEN”. DO NOT insert or
take out the SIM card when the main unit console panel is powered on.
(Option) Connect the phone cord to LINE Port on back of console.

Connect the regular telephone device to TEL port on
back of console. Route the phone cord through the
channel toward the side of the console (if you have no
landline, you can use OBi110/ MagicJack / Vonage /
Ooma VoIP service to connect your internet Router /
Modem then connect console to the VoIP device ) if you
use landline, priority call by landline, then GSM SIM
card.
Note: If you use only landline, you cannot dial out
through main console direct, you need use your home
phone to dial out or receiving call, system will auto dial
out if alarming, but if you use GSM SIM card, you can
use the main base as telephone, you are able to dial out or receive call from main base directly.
Connect the power adapter to POWER port on back of console
Route the power adapter ( 12V 1A ) cord through the channel toward the side of the console
Plug the power adapter into nearby electrical wall outlet that is not controlled by a switch
Keep the Battery Switch at ON position for internal battery backup charging.
Wired Port - Function interface of the main unit
1
GND
Ground
2
Z3
Wired sensor 1: support both NO and NC (Auto create Zone 49)
3
GND
Ground
4
Z4
Wired sensor 2: support both NO and NC (Auto create Zone 50)
5
GND
Ground
6
+12V
DC 12V Positive Wired in
Keychain Remote
Press to Arm / Activate your system as Away from home
Press to Disarm/ Deactivate your system when you come back home
Press to Home arm /Active your system as Stay Home( if you go to Sensor-Edit and set part
of sensors for Home zone as No, when you press Home, that sensor will disable, and all other
sensors still enable)
Press this key you will see icon on LCD screen, that means you have enabled your Chime
function, ( to make it work if you go to Sensor-Edit and set your door sensor for Chime zone as
Yes, you will hear a music bell sounds when you open your door), press once to enable, press once again to disable.
Press once for "silent emergency alarm mode”. This allows you to call for help silently when someone threatens your life
without triggering the siren and alerting the invader. If you press and hold for 3 seconds, the siren will start sounding loudly in
emergency alarm mode.
Program Remote Keychain:
If you received a pre-Programed system kit, please ignore this step and do not program it again.
Press PROGRAM button on console, enter the default password 888 888. Select Remote Controllers then press
Enter on console you will see below list.
Add Select Add press Enter, then you will see Trigger Controller Code, press any button on your remote Keychain. Nine
digits will appear on console screen for 1-2 seconds. This is the unique address for this keychain. The console will

request you add an owner name for this remote. Input a name for this remote and then press SAVE. You will see
Record owner Name, then press Enter and record a voice for this remote keychain.
Note: Each time you press Add, follow steps above. You can add one remote and a maximum of 8 Keychain Remotes.
Edit select Edit press Enter to find the name of remote then press Enter you can edit the remote keychain name or record a
voice for the remote keychain.
Delete select Delete and press Enter, you can find all your remote names to delete one or all remote keychains if you want to
remove the remote keychain from console panel.
Delayed Arm If you select Delayed Arm and press Enter, then set Yes, it will give you 60 seconds to leave the house. Default
is set Delay as Yes. It gives you 60 seconds to leave the house when you do arm system by remote keychains. (You
can change this time using System Settings menu,under Arm delay time)
Program and Mount Bracket Door/Window Sensors
If you received a pre-Programed system kit, please ignore this step and do not program it again.
All new Door/Window sensors you need should be programmed to your console.
Open the cover and remove the insulated paper then close the cover.
Put small magnet next to sensor
Press PROGRAM button on console, enter the default password 888 888. Use Scroll key to choose Sensor then press Enter
on Console.
Add press Enter again, then you will see Trigger Sensor / Code. Trigger your sensor by moving the small magnet away from
the large transmitter. Then console will request you to add a Zone Name for this sensor. Input a name for this sensor,
then press SAVE. You will see Record Sensor Name, press Enter record your own voice for this sensor. You will
hear this voice when you get alarming calls.
Note: Each time you press Add, follow above steps.You can add from one up to fifty sensors.
Edit select it then press Enter, you can use Auto search or Manual search to find your target sensor and high light it then
press Enter to Edit Sensor Functions as below list
Note: if you don’t know sensor name then choose Auto Search, when you trigger an individual sensor and its name will
be displayed on the console panel. Select the sensor name and press Enter, then you will see the menu displays as
below: (MAKE SURE ONLY ONE SENSOR IS TRIGGERED EACHTIME TO AVOID ANY ACCIDENTAL TRIGGERING
OF A DIFFERENT SENSOR. PLEASE KEEP ALL YOUR MOTION SENSORS IN DIFFERENT ROOMS, AND MAKE
SURE THAT ALL WINDOW/DOOR SENSORS MAGNET PARTS ARE ATTACHED TO LARGER PARTS AS CLOSE
STATUS.)
Edit Zone Name:Highlight Edit Zone name, press Enter and you will be able to rename the sensor.
Record Zone Name: Highlight it press Enter, select “Record”, you are able to record 5 seconds of your own voice
accordingly. If recording a sensor name in your own voice to identify a sensor, when you receive an alarming call on
your cell phone or any other phones, you will hear the sensor name.
Emergency Zone Highlight it press Enter, Default is NO, (If you set YES, the zone will be on 24hours, regardless of your
system’s Arm or Disarm status. This is recommended to be used for smoke detector, panic button, water leak sensor and temperature
sensors only. DONOT set any door sensor or motion sensor as Emergency zone).
Home Zone Highlight it press Enter, Default is YES, ( if you select NO, the zone will disable during home alarm status,
recommended for motion sensor NO, and all Window/door sensor YES)
Chime Zone Highlight it press Enter, Default is NO,( if you set as YES, the zone will alert you as a bell during disarm and home

alarm status, use for door only)
Delayed Zone Highlight it press Enter, Default is NO, (if set YES, allows you to come back home and open the door without
triggering the system. System default delay alarm time is 45 seconds. You can change this time by going to "System Settings" and set
the Alarm Delay time).
Siren Enable Highlight it press Enter, Default is YES, (if set NO, siren will disable when this zone triggered, no siren alarm will
sound.)
Note: All zones are instant zones by Default.(“Instant “refers to the system being immediately armed if any zone is triggered
when the system is in armed status.)
Delete select it then press Enter, you can find the target sensor and delete it, you can delete any sensor from console
panel.
NOTE: After programming all sensors to your console, please test each sensor before you mount the sensor to the
appropriate location. DO NOT close the door fast then one second during testing, open door and waiting 1-2 seconds when
you see sensor light off then close the door, otherwise the console may only receive door open signal and not detect the door
close signal then shows the door is opening on LCD screen.
Place each sensor in the appropriate location.
Note: If possible, place the bracket on the stationary frame
of door or window, and place the magnet on the door or
window itself. You may apply super glue on the surface
of window/door before use 3M tape stick.
Various orientations between the Bracket and Magnet may
be used as long as 3/4" distance is not exceeded. See
Example in Figures 1-4
NOTE: SPACERS IN BOTTOM TRAY MAY BE USED ON THE BRACKET OR MAGNET TO ADJUST ALIGNMENT
Once you have determined the appropriate location and orientation for the Bracket and Magnet, attach them with double-sided
tape (the Magnet Space and Bracket Space are optional; only apply when your door/window gap is big or very low)

Program and Mount Motion Sensors:
Prepare Motion Sensor
A. Separate the front and back covers of the Motion Sensor by pressing the tab with your
finger or the top of a pen (Figure A and B).
B. Remove insulating paper from the battery and CLOSE the cover. The sensor needs 1-3
minutes to initialize itself. You will see a red indicator blink once every 3 seconds during
initialization. If you don't see the indicator blink as described during initialization, please
open the cover, remove the battery and reinstall the battery again until you see the
indicator flash as described. The sensor will be ready for use when the indicator stops
blinking. (Note: DO NOT keep the cover open since it may effect the sensor during
initialization and cause the sensor to not work properly after)
C. 1 switch for battery notification, Default is set to ON. OFF position disables the low battery
notification.
2switch for LED signal light. The default is set to on, but if you do not want a flashing
light when the sensor detects an intruder, you can turn it off. When the battery is low, the
LED light becomes yellow.
Motion sensor sensitivity adjustment
A = Switch 2
B =Switch 1
Low sensitivity: Switch 2 at ON position and Switch 1 at OFF position
Medium Sensitivity: Switch 2 at ON position and Switch 1 at OFF position
High Sensitivity (Default): Switch 2 at ON position and Switch 1 at ON position
Program the Motion Sensor ( only for DIY kit or add new sensors)
If you received a pre-Programed system kit, please ignore this step and do not program
it again.
Before programming any sensor, you need to switch off all your existing sensors and disarm your system.
Press PROGRAM button on console and enter the default password 888 888. Use Scroll key to choose Sensor then press
Enter on Console.
Add press Enter you will see Trigger sensor /Code , then walking 2-3 steps in front of The Motion Sensor which you have
prepared and you will see nine digits displayed on console screen for 1-2 seconds. This is the unique address for this
sensor. The Console will request you add a Zone Name for this sensor, then press SAVE. You will see Record Sensor
Name, then press Enter and record a voice for this senso.
(MAKE SURE ONLY ONE SENSOR IS TRIGGERED EACHTIME TO AVOID ANY ACCIDENTAL TRIGGERING OF A
DIFFERENT SENSOR. PLEASE KEEP ALL YOUR MOTION SENSORS IN DIFFERENT ROOMS, AND MAKE SURE
THAT ALL WINDOW/DOOR SENSORS MAGNET PARTS ARE ATTACHED TO LARGER PARTS AS CLOSE STATUS.)
Edit select it then press Enter, you can use Auto search or Manual search to find your target sensor and high light it then
press Enter to Edit Sensor Functions as below menu list
Note: if you don’t know sensor name then choose Auto Search, when you trigger an individual sensor and its name will
be displayed on the console panel. Select the sensor name and press Enter, then you will see the menu displays as
below: (MAKE SURE ONLY ONE SENSOR IS TRIGGERED EACHTIME TO AVOID ANY ACCIDENTAL TRIGGERING
OF A DIFFERENT SENSOR. PLEASE KEEP ALL YOUR MOTION SENSORS IN DIFFERENT ROOMS, AND MAKE
SURE THAT ALL WINDOW/DOOR SENSORS MAGNET PARTS ARE ATTACHED TO LARGER PARTS AS CLOSE
STATUS.)
Edit Zone Name:Highlight Edit Zone name, press Enter and you will be able to rename the sensor.
Record Zone Name: Highlight it press Enter, select “Record”, you are able to record 5 seconds of your own voice
accordingly. If recording a sensor name in your own voice to identify a sensor, when you receive an alarming call on your
cell phone or any other phones, you will hear the sensor name.
Emergency Zone Highlight it press Enter, Default is NO, (If you set YES, the zone will be on 24hours, regardless of your

system’s Arm or Disarm status. This is recommended to be used for smoke detector, panic button, water leak sensor and temperature
sensors only. DONOT set any door sensor or motion sensor as Emergency zone).
Home Zone Highlight it press Enter, Default is YES, ( if you select NO, the zone will disable during home alarm status,
recommended for motion sensor NO, and all Window/door sensor YES)
Chime Zone Highlight it press Enter, Default is NO,( This function not work with motion sensor)
Delayed Zone Highlight it press Enter, Default is NO, (if set YES, allows you to come back home and open the door without
triggering the system. System default delay alarm time is 45 seconds. You can change this time by going to "System Settings" and set
the Alarm Delay time).
Siren Enable Highlight it press Enter, Default is YES, (if set NO, siren will disable when this zone triggered, no siren alarm will
sound.)
Note: All zones are instant zones by Default.(“Instant “refers to the system being immediately armed if any zone is triggered
when the system is in armed status.)
Delete select it then press Enter, you can find the target sensor and delete it,
Test the Motion Sensor
The Motion Sensor will initialize itself during the first 1-3 minutes after the front cover is re-attached（DO NOT KEEP Cover
open）. Do not test it during initialization. You can walk 3-5 steps in front of motion sensors after initialization, the LED will
remain on for 3 seconds when motion is detected until the Motion Sensor short blinks once again before resuming motion
detection for next detector.
1. Move away from the area that is in direct line of sight of the Motion Sensor (move to an adjacent room). Waiting 2-3
minutes until the LED stops blinking.
2. Move back into the line of sight of the Motion Sensor, walk around 3-5 steps. (this will trigger the main console).
If the Motion Sensor test is successful the LCD screen will display " xxx Sensor Alarm". If these words do not appear, either (A)
the 20-second waiting period since the last trigger has not expired, or (B) the Motion Sensor is not in communication with the
PiSECTOR system main console.
If you want to re-start the initialization again, open the Front Cover and remove battery waiting for 5 seconds then re-install it
again, as shown in Figure 1 and then re-attach the Front Cover.
Note1: For saving battery power, motion sensor may be insensitive if you active it more than three times in a few minutes. Please leave the
detectable area for a few minutes and come back, it will detect you again.
Note2: Motion sensor may be insensitive or give a lot false alarms if the temperature is more than 98F (37C).
Mount Motion Sensor
D. Place the motion sensors in the following
location recommendations (check
marked locations) shown in Figure C.
Avoid the example location marked with
the "X" which are household areas that
typically cause false alarms, such as heat,
air conditioning, fans, or direct sunlight.
The recommended mounting height is
6.5-7.0 feet for both coverage and pet
immunity purposes.
E. Apply the 3M adhesive tape in the locations shown in Figure D for corner mounting or wall mounting (apply for super
glue on the surface of window or wall before stick 3M adhesive tape to void any falling).
If you prefer to use screws to mount the motion sensor, follow the screw position shown in Figure E (optional)

Detection Patterns
Motion sensor Specifications
Replacement Battery: CR123A
Mounting Height: 6.5-7.0Feet
Range: Approximately 40 feet with 90 degree field of view in Vertical and 110 degree field of view in Horizon

Wireless Sirens
Plug the siren into wall outlet, then press PROGRAM key on console. Enter the default password 888 888. Use scroll key
to select Wireless Sirens, press ENTER, you will see below list.
Add If you received a pre-Programed system kit, please ignore this step and do not
program it again
Add an Indoor Wireless Sirens, highlight Add press Enter, you will see a default siren name
such as Siren 1, then press Enter You will see "Put siren in Setting Mode". Go to the wireless
siren and press the code button one time on the wireless siren, you will see all 4 lights are on.
This means the siren is in setting status waiting for the console to send a signal. Then go back
to the console, press Enter and you will hear two beeps from the console and will see “Add
successful”. Then you need press Set button 5 times until all light off to exist the set mode on
siren. DO NOT test it when all 4 LED lights are on) Be aware If you press and hold code button more than 3 seconds,
the siren will be deleted from console panel.
Add an outdoor wireless sensor, highlight Add press Enter, you will see a default siren name such as Siren1 / Siren2
/ Siren3, then press Enter You will see "Put siren in Setting Mode". Plug siren into the
power adapter ( 9V 500mah ), and you will hear ONE beep. Unplug and plug the siren a
second time within seconds after the first time, you will hear ONE beep again. Unplug
and plug the siren the third time within seconds after the second time, you will hear a
FEW short beeps from the siren. The FEW short beeps mean the siren is ready and in
setting mode for program. Go back to the main console and press Enter immediately
(no more than 5 seconds after the few short beeps), you will hear 3 beeps, 2 short
beeps, and 3 beeps consecutively for conformation. That means your siren has been
added to your main console. You may press “back”key until the console displays
“System Disarmed”and the date /time page. Unplug siren from the power adapter and
wait for 10 seconds to exit the setting mode. Test: Connect siren to the power adapter.
Press Emergency key on the main console. You should hear the alarm sounding.(If you
plug the siren to the adapter, and unplug, plug consecutively and rapidly for 5 times, the siren will be deleted from the
main console. You may need to follow the steps above to re-program)
EditSelect Edit and press Enter, you will see all 3 sirens name, select a siren’s name and press Enter. You will then be able
to change the siren’s name.
Delete If you find system shows “Space full”while you add extra siren or reprogram siren, select "Delete". Delete all "Siren
1”"Siren 2 “"Siren 3”names, then you are able to re-program your siren by upon instructions (you can’t delete the siren,
this only deletes the sirens name. if you want to delete siren from your system, you need delete it on Siren, detail see
how to delete your siren on siren manual page or FAQ.)
Siren Enable Select "Siren Enable". If you set No, the sirens will not give any alert for the entire system. If you only want to
quiet an individual zone's siren, you have to go to Sensors menu and Edit it. For details, read Edit under of Sensors.
DurationYou can set wireless sirens to sound on a continuous alert. You can set it from 1 second to a maximum of 180
seconds.
Arm/DisarmTone Select Arm/Disarm Tone and press Enter. If you set Yes, when you use the remote control to arm and
disarm system, you will hear a loud beep warning from the siren. You can set No to turn off this warning tone if you don’t
like it. Default is No.
Encrypt select Encrypt then press Enter, you will see default 1234 and blink, you can direct input another 4 digits to encrypt
your siren. BEWARE If you change encryption code to a new code, you need to re-program all of your wireless sirens to
the console again, you may change it before you program your sirens. Once you change it, DO NOT change it when you
are going to add a second or third siren, otherwise you will lose the first siren’s program.
Video: https://www.youtube.com/watch?v=JcPcwCBLQyc&feature=youtu.be
https://www.youtube.com/watch?v=BQEkK__q3Ug&feature=youtu.be

Add Contact Phone Numbers
Press PROGRAM key on console. Enter the default password 888 888. Use scroll key to select Phone Numbers, press
Enter, you will see below list
Add Select Add press Enter. You will see Input phone number, direct input your area code and phone number, press save.
You can add maximum of 6 numbers for emergency contact if the system is triggered. It is recommended to add your
cell phone and your family or friends’ numbers. DO NOT add 911 or the local police number directly unless you get a
permit.
Edit select Edit press Enter, you will see Phone#1, Phone#2…select the target number which you want to edit, then press
Enter, you will see Auto login, press Enter, If you set Auto login as Yes, then you can remotely call the system
telephone number from anywhere in the world, you do not need to enter the password again to save you time when
entering system remotely. It is recommended to set only your own number as auto login, all other numbers, keeps
default as No.
Delete Select Delete then press Enter, you will see all numbers which you saved, choose the target number which you
want to delete then press Enter and delete it.
SMS Numbers
This system can store 3 text message receiving cell phone numbers. When alarming, it will send text to all these numbers
e.g. power outage or any sensor triggered, you will get notification by text message.
Press PROGRAM key on console. Enter the default password 888 888. Use scroll key to select SMS Numbers, press
Enter, you will see below list
Add select Add press Enter. You will see Input phone number, direct input your area code and cell phone number. press
save. You can add maximum of 3 numbers for receive text message
EditSelect Edit press Enter,you will see Phone#1, Phone#2… select the target number which you want to edit, then press
Enter, you will see Auto password. If you set Auto password as Yes, then you can remotely text the system
telephone number from anywhere in the world, you do not need to enter the password again to save you time when
arm/disarm system remotely. It is recommended to set only your own number as auto login, all other numbers, keep
default as No.
Delete Select Delete then press Enter, you will see all numbers which you saved, choose the target number which you
want to delete then press Enter and delete it.
Arm/Disarm Notification Select Arm/Disarm Notification then press Enter, if you check Yes, you will get a text message
notification during system ARM or DISARM time, default is NO.
Outgoing Message
Press PROGRAM key on console and enter the default password 888 888. Use scroll key to select Outgoing Messages,
press Enter, you will see below list
Edit Text Message press Enter you can directly input a text message for outgoing.
Record Voice Message Select it and press Enter, select Record, and press Enter. You will see “Recording”and a
counter from 10 to 00. When you see 10, you need to immediately start recording your voice and stop when you see 00.
It is recommended that you record your home address for the outgoing message.
Play You can select Play to play your voice. If you do not like it, you can Delete it and Record it again until you are satisfied.
Note: The closer you are to the console during recording, the better the quality of the recording. Your mouth should be
no more than 2 inches away from the console.

Connect Monitoring Center
Press PROGRAM key on console. Enter the default password 888 888. Use scroll key to select Monitoring Center. You
can call your Monitoring Company to set up all requests. Please make sure your monitoring company supports ADMECO
protocol if you want a third party Monitoring Company to monitor your system (it will cost you a monthly monitoring charges
depending on which company you choose.)
Monitoring Center Number Selector and press Enter then selects Add to add your monitoring center telephone number
ADMECO Contact Id Selector and press Enter then selects Add to add your monitoring company account number.
Select Delete to delete your account number, select ADEMECO Contact ID then press Enter to select the protocol ID
according your monitoring center protocol ID request.
Upload Alarm Data Selector and press Enter if set YES, all your data will be upload to monitoring center station, default
is NO.
Upload Arm/Disarm Data Selector and press Enter if you set YES, every time you do arm or disarm your system
information will be upload to monitoring center station, default is NO.
Daily Schedule
Press PROGRAM key on console. Enter the default password 888 888. Use scroll key to select Daily Schedule.
Enable If you want to enable this function, first select Disable then press Enter, set NO, then back and select Enable, you
can set the Arm time for your departure, and Disarm Time for when you arrive Home, then the system will Arm/Disarm
automatically on schedule, so that you will never forget to arm or disarm system.
Disable If you want to disable this function, select Disable then press Enter and check Yes. Default is set to disable as
YES.
System Settings
Press PROGRAM key on console. Enter the default password 888 888. Use scroll key to select System Settings, you will
see below list.
Password Select Password then press Enter you will see Old Password 888888 then press Enter and input 6 digits(not
letter or icons) new password press Enter and input same password to confirm your new password, then press Save
Arm Delay Time Select it and press Enter, you will see 60, directly input 2 digits for your delay time, you can change the
Delay time to allow you to have enough time to leave the house. Defaults set at 60 seconds. The Delay Time for entire
system. Maximum is 60 seconds.
Alarm Delay Time Select it and press Enter, you will see 60, directly input 2 digits for your delay time, you can change
the Delay time that allows you to open the door to disarm system when you return home. Default is set to 40
seconds.( This Alarm Delay time only works when you set individual sensors as Delay Zone. Otherwise it does not work.
E.g. Disarm system press PROGRAM key then input password, highlight Sensor press Enter, highlight Edit press
Enter, than highlight Manual Search press Enter and choose the sensor name then press enter, use scroll key find
Delay Zone then press Enter and check Yes, save it. ), Maximum is 60 seconds.
Landline Cut Warning Select it and press Enter, If you set Yes, during System Arm or Home Status, if an intruder cuts
the landline or unplugs the landline jack, the system will immediately go off and sirens will start alarming. Default is set
as No
Ring Time Before Answer Select it and press Enter, you will see 1 flash, directly input a digit for your ring circle
(maximum is 9), it allows you to change the ring times for answering your regular home phone, e.g. if you set it as 5
rings, during 5 rings you can answer your regular home phone, after 5 rings if no one answers the regular home phone,
the alarm system will answer it. You will hear a prompt "Enter your Password" then you can enter your password 888
888 to control the System. Press 1 to Arm System, Press 2 to Disarm System, Press 3 to listen in. Press 4 to intercom,
press # to end.

Door/Window Open Reminder Select it and press Enter, If you set it Yes, you are not able to arm your system normally
when doors or windows are open. It will remind you which zone door or window is open. You must close it, unless you
arm the system by pressing button and holding for 3 seconds to force system to be armed. The default is set to
NO.(This function will not work with updating system GSM06)
Note: this function only work when you use remote keychain arm your system, you still can press Arm key input
password on the console without this reminder warning.
Date/Time Allows you to manually set your local date and time
Priority Dial Telephone When you connect your console with dual network Landline and GSM both, then you may need
to highlight “Priority Dial Telephone”press Enter and highlight “Yes”then Save it, this function allows you to set your
system and use your landline priority to call out and save your SIM card credit, if someone cuts your landline the system
will automatically call out from your SIM card. If you only use SIM card, please set it as NO.
Language English
Factory Reset<Restore Defaults> Allows you to set all functions as default without deleting your sensors and sirens so
you do not need re-program again. If you choose<Format System>, it will go back to factory default and format all your
settings including your sensors and sirens. Then you will need to re-program all sensors, sirens and remotes to the
console again. Beware of this function.
About System
Version press Enter you will find your software version
Production Date: press Enter you will see the producing time of your system
Manufacture By Pisector Inc.
IMEI: press Enter you can find IMEI number for your system, maybe request to active your SIM card
Remotely Control Your Home Security Alarm System
Dial the number of the main unit console panel by your cell phone, and after 1 ring, you will hear a voice prompt “Please enter
password”. If the password is correct, you will then hear a voice prompt “Please enter instruction" then you can press 1 to arm,
Press 2 to disarm, Press 3 to monitor, or Press 4 to intercom. If the password is incorrect, you will hear a prompt voice
“Wrong password, please re-enter”.
The system default operate password is 888888. Make sure to enter the password firmly by pressing and holding one digit at a
time so you can hear a beep for each key press. You may need to hold keys for half a second at a time.
Press [1]: arm, if finished successfully, you will hear a voice prompt “System armed”.
Press [2]: disarm, if finished successfully, you will hear a voice prompt “System disarmed”.
Press [3]: monitoring for 30 seconds, to continue monitoring, press [3] again for another 30 seconds. You can cancel monitoring
at anytime by pressing [1] to arm and [2] to disarm.
Press [4]: two-way intercom for 30 seconds. You cannot operate the main unit console panel during this time. You can cancel
intercom at anytime by pressing [1] to arm and [2] to disarm.
Or just simple text message from you cell phone to Arm/Disarm/Home Arm/History checking it
Password follow by 1 for Arm. i.g 888881 Password follow by 2 for Disarm. i.g 8888882,
Password follow by 3 for Home Arm, I.g 8888883 Password follow by 4 for History checking. i.g 8888884.
Answer Alarm Call: to prevent alarm call answered by voice mail, you need manually answer the incoming alarm on your
pre-saved cell phone then press # # twice to stop call the second number.

Wireless Panic Button (Option)
Program Panic Button
If you received a pre-Programed system kit, please ignore this step and do not
program it again.
Panic Button you need should be programmed to your console.
Press PROGRAM button on console, enter the default password 888 888
Use Scroll key to choose Sensor then press Enter on Console. Then choose Add, press Enter again,
then you will see Trigger Sensor, trigger your Panic Button by pressing the Red circle button. Then the
console will request you to add a Zone Name for this sensor. Input a name for this sensor, then press
SAVE. You will see Record Sensor Name, press Enter, record a voice for this panic button.
Set the Panic button as Emergency zone, use it in 24/7 regardless of console being Armed or Disarmed
(Press PROGRAM button on console, enter the default password 888 888, use Scroll key to choose
Sensor then press Enter on Console. Choose Edit press Enter, then choose Manual Search press Enter, use Scroll key to find
Panic button name and highlight it then press Enter, use Scroll key to choose Emergency zone then press Enter, highlight Yes
then press Save, use function key “Back”to exist the program) In the SAME way you can add a Smoke Detector, Water Leak
Sensor, Carbon Monoxide, and Temperature Sensors.
You also can add a Glass Break Sensor to your system.
Wireless Signal Transmitter (option)
Wireless Signal Transmitter expands your wireless range up to 500 feet and makes the
communication between all sensors and the main console better. Please install the antenna
and plug a 12V 1A power adapter to the Power plug. Place the Wireless Signal Transmitter
away from the main console for about 10 feet. Keep code 4 and 5 at ON position, all other
codes at OFF position. The Transmitter will then start to auto transfer all the signals
between the sensors and the main console.
(Note: if you notice any issue such as an “open icon”displaying on the screen when the
door or window is open because the main console has detected that the door or window is
open, and the same icon is still showing after physically closing the door or window, a
communication problem must have caused this issue. For a solution, you may need
purchase this repeater to add to your system.)

Extra Wireless Keypad Instruction ( option)
Model: WKP-03
This keypad does not work alone. You need to program it with PiSector Alarm Systems. It supports System model GS07, GS08, PS03 series
systems.
Anti-Remove Spring
Package includes
PiSector Keypad x 1
Power adapter 12V 1A, input 100-240V output 9- 12V, Current 1A
RFID Door Access Keychain Tag X 2
Add the keypad to console
Step 1 Connect power to the keypad, and you will see Arm indicator light flash once every second. This is Stand by(Disarm) status, meaning
system is at power on. To keep internal back up battery in charge, please turn on the battery switch to ON position. Put the keypad on a
hard surfaced table, and make sure to not trigger the keypad by releasing the anti-move spring, or by pressing the anti-move spring with
hand. Make sure the keypad does not get triggered during programming.
Step 2 At your main console, press Program followed by password. Then choose Remote Controllers ---press Enter --- select Add --- press
Enter again. When you see "Trigger Controller, Code: " display, go to your extra keypad, press default password 1 2 3 4 5 6 followed by Arm
key (the lock icon), and you will see 9 digits display on the console. This is unique address for the extra keypad on the console. It will be auto
saved after 3 seconds, and you will see "Add Owner Name". You can give a name to this keypad on the console, and then follow the steps to
record a voice for the keypad name as your choice (optional). After that press Enter to continue until you see Add successful.
Step 3 Press Chime key to exit setting status.
Add RFID Key chains to Keypad
During system disarm status, you can press default password 1 2 3 4 5 6 followed by Enter key. You will see Set indicator light on and Enter
key flashing. Then press 2 0 1 followed by an Enter key --- Send indicator light on --- move your target key chain (the one that you want to
add) close to the keypad read area, and you will hear a few short beeps, meaning add successful. You may add maximum 8 pieces RFID keys.
At the end press Chime key to exit setting status.
Delete RFID key chains from your PiSector Keypad
During system disarm status, you can press default password 1 2 3 4 5 6 followed by Enter key. You will see Set indicator light on and Enter
key flashing. Then press 2 1 1 follow by an Enter key. It will auto delete all key chains. You CANNOT delete one key chain each time. If you
lost any key chain please choose to delete all key chains, then add other key chains again. At end, press Chime key to exit setting status.
Operating instruction
Password followed by Arm key to arm system--- Arm indicator light on in solid
Password followed by Disarm key to disarm System. Open light on for 3 seconds (depending on how long you set for door open time ---
default 3 seconds) --- Arm indicator light flashes once every second
Password followed by Home key to arm system when you are at home--- Arm indicator light flashes once every 3 seconds
Password followed by SOS for emergency

Password followed by Chime key to change system to Chime status
Use key chain to disarm system directly without entering any password
Other features
Set Door Open Time
During system disarm status, you can press default password 1 2 3 4 5 6 followed by Enter key. You will see Set indicator light on and Enter
key flashing and press 5 0 + T T (“T T” for time, from 01 to 99 seconds) and Enter. This time is for how long you need an access to door
without triggering the alarm. For example, when you use a key chain or password to open the door, how long you would want the door to
be closed and system still be in arm status.
Wireless Encryption
If you had a neighbor having the same system or other devices that interfere your system and always results in false alarm, then during
system disarm status, press default password 1 2 3 4 5 6 followed by Enter key. When you see Set indicator light on and Enter key flashing,
press 4 0 + dddd (any 4 digits pass code --- you do not need to remember this pass code it is only for encrypting the system with other
device)
Change Password
After setting up your keypad, you may change the default password to your own password for safety.
During system disarm status, you can press default password 1 2 3 4 5 6 followed by Enter key. You will see Set indicator light on and Enter
key flashing. Then press 3 0 + new password + Enter, repeat the new password follow by Enter one more time (you may set new password
up to 6 digits). Then press Chime key to exit setting status. (Please keep your new password to a safe place and do not forget it)
Reset Password
If you forget your password, remove the keypad from the wall. At backside of the keypad, you will see Reset button, press the reset button
and hold for 3 seconds, it will reset the keypad password to default password 1 2 3 4 5 6.
Wired Port Connection for Magnetic force lock or Electronics lock(Option)
Magnetic force lock and Electronic lock. Please make sure which type of lock you have, and select the correct connection
Fig 1 for Normal Close Fig 2 for Normal Open