Eaton Menvier 20 User manual

Issue 7
Control unit software version 4.04

Menvier30/40/100/300
Page ii
© Eaton’s Security Business. 2014
IN NO EVENT WILL EATON’S SECURITY BUSINESS BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL , OR INDIRECT
LOSS OR DAMAGE, INCIDENTAL DAMAGES, STATUTORY DAMAGES, EXEMPLARY DAMAGES, LOSS OF PROFITS,
LOSS OF REVENUE, LOSS OF ANTICIPATED SAVINGS, LOSS OF BUSINESS OR OPPORTUNTIY, LOSS OF
GOODWILL OR INJURY TO REPUTATION, LIQUIDATED DAMAGES OR LOSS OF USE, EVEN IF INFORMED OF THE
POSSIBILITY OF SUCH DAMAGES. EATON’S SECURITY BUSINESS’S LIABILITY FOR DAMAGES ARISING OUT OF OR
RELATED TO A PRODUCT SHALL IN NO CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT FROM WHICH
THE CLAIM ARISES. TO THE EXTENT PERMITTED BY APPLICABLE LAW, THESE LIMITATIONS AND EXCLUSIONS
WILL APPLY WHETHER EATON’S SECURITY BUSINESS’S LIABILITY ARISES FROM BREACH OF CONTRACT,
BREACH OF WARRANTY, TORT (INCLUDING BUT NOT LIMITED TO NEGLIGENCE), STRICT LIABILITY, BY
OPERATION OF LAW, OR OTHERWISE.
Every effort has been made to ensure that the contents of this book are correct. The contents
of this book are subject to change without notice.
Part number 12431689 6/1/2014
Warning: Mains voltages are present inside control unit. No user
serviceable parts inside.

Menvier30/40/100/300
Page iii
Contents
1. Introduction .............................................................1
Setting and Unsetting ...................................................3
Alarms and Reset ............................................................... 3
Security Levels .................................................................. 3
Wards............................................................................... 4
24 Hour Alarms.................................................................. 4
Communications ..........................................................4
Security Grade.............................................................5
Controls and Displays ...................................................5
Controls:........................................................................... 6
Displays ............................................................................ 7
Users..........................................................................8
Types of User .................................................................... 8
Identifying Users................................................................ 9
Access to the System ................................................. 10
Access Codes................................................................... 10
Proximity Tags................................................................. 11
Remote Controls .............................................................. 11
TwoWay Key Fob.............................................................. 12
Radio Hold Up Alarms (HUA).............................................. 13
2. Alarms ....................................................................15
Silencing an Alarm ..................................................... 15
If You Cannot Reset the System......................................... 17
Accidental Alarms....................................................... 18
Speech Messages ....................................................... 18
Acknowledging a Speech Message ...................................... 19
Alerts (or Why is it Beeping?) ...................................... 19
Technical Alarms.............................................................. 20
3. Setting and Unsetting .............................................21
Setting and Unsetting With a Keypad............................ 21
Setting ........................................................................... 22
If the System Will Not Set ................................................. 27
Other Reasons Why the System May Not Set ............................ 28
Unsetting the System Using a Keypad................................. 29
Using Radio Keypads and Remote Controls.................... 30
Using a Radio Keypad ....................................................... 30
Using a Remote Control .................................................... 32
Using a Two-Way Key Fob ................................................. 33
4. Administration ........................................................35
Entering and Leaving the Menu.................................... 35
Editing Text............................................................... 36
Omitting Zones .......................................................... 36
Shunt Groups ............................................................ 38
Activating Shunt Groups ................................................... 38
Users........................................................................ 40
Editing Existing Users ....................................................... 41

Menvier30/40/100/300
Page iv
Adding Users ................................................................... 53
Deleting Users ................................................................. 56
Viewing the Log ......................................................... 57
Testing the System .................................................... 59
Sirens & Sounders............................................................ 59
Keypad ........................................................................... 62
Walk test ........................................................................ 63
Outputs .......................................................................... 65
Remotes and Two-way Keyfobs ......................................... 67
Radio Hold Up Alarms ....................................................... 68
Proximity Tags................................................................. 70
ARC Reporting ................................................................. 71
ARC Reporting ................................................................. 72
System Configuration ................................................. 73
Switching the Chime On/Off .............................................. 73
Allowing Remote Access.................................................... 74
Setting the Date and Time ................................................ 75
Calendar Set ................................................................... 76
Programming Outputs ...................................................... 86
Programming Remote Controls and Two-Way Keyfobs .......... 91
Deleting Remote Controls.................................................. 99
Preventing Any Remote From Unsetting the System ............102
Allowing a FOB-2W-4B or 727r to start a HUA ....................103
Starting a Call To Downloader ..........................................104
Redirecting Speech Messages ...........................................105
Turning Outputs On/Off ............................................ 107
What System Have I Got? ......................................... 108
Seeing Which Communications Module Is Currently Installed:109
List of Menu Options ................................................ 110
Alarm Functions At a Glance..................................... 111
Setting and Unsetting............................................... 111
After an Alarm......................................................... 112
To Start a HUA from the Keypad................................ 112

Menvier30/40/100/300
Page v
Compliance Statement
The Menvier30:
Is suitable for use in systems designed to comply with PD6662:2010
at Grade 2, and environmental class II.
Is suitable for use in systems designed to comply with the
requirements of EN50131-3 at Grade 2 and environmental class II.
Complies with the requirements of EN50131-6:2008 at Grade 2 and
environmental class II.
Menvier40, Menvier100 and Menvier300:
Are suitable for use in systems designed to comply with
PD6662:2010 at Grade 2, Grade 3 and environmental class II.
Are suitable for use in systems designed to comply with the
requirements of EN50131-3 at Grade 2, Grade3 and environmental
class II.
Comply with the requirements of EN50131-6:2008 at Grade 2, Grade
3 and environmental class II.
When fitted with the appropriate communicator these products are
compliant with EN 50136-1. They allow the alarm transmission system to
meet the performance requirements of EN 50131-1:2006 ATS 2 provided
that:
a) They are installed in accordance with the installation instructions.
b) The connected PSTN is functioning normally.
If the installer selects a non-compliant configuration then they must
remove or adjust compliance labelling
Third party testing carried out by ANPI.
Please Note:
This Guide applies to Menvier30, Menvier40, Menvier100 and Menvier300
control units with version 4.04 software.

Menvier30/40/100/300
Page vi
This page is intentionally blank.

Menvier30/40/100/300
Page 1
1. Introduction
At the heart of an alarm systems is the control unit, its expanders and
keypads.
The control unit contains the main processing unit, the power supply and
stand-by battery. The stand-by battery can keep the alarm system going for
several hours if the mains supply fails.
Connected to the control unit by cable are the keypads and, where
applicable, expanders. The expanders provide extra connection points for
detectors, either wired or radio. The keypads each have a two line display
to show you status information, and various keys for operating the system.
The keypads also contain a speaker to give warning tones when the
system is setting or unsetting.
Users identify themselves to the system by keying in access codes at the
keypads. If they do not wish to use access codes then some types of
keypad also contain proximity tag readers, allowing users to identify
themselves by means of small electronic tags that they carry with them.
In addition to an access code or proximity tag, each user can be assigned
one portable four-button remote control and/or one two-button hold up
alarm.
To protect an area the control unit can operate a range of detectors.
Detectors can be connected to the control unit or expanders by wires, or
communicate to a radio expander using a small radio transmitter. Figure 1
shows some examples. In addition to fixed detectors the control unit can
also monitor small portable transmitters that users can employ to start
alarms remotely, for example in the case of a Hold Up Alarm. (Hold Up
Alarm (HUA) is also known as Panic Alarm or PA.) These transmitters are
called Hold Up Devices, or HUDs.
When the control unit detects an alarm, it can start an external
sounder/strobe unit by sending the appropriate radio signal. In addition the
control unit can also communicate using a variety of plug on modules.
Some modules also provides speech recording and playback facilities so
that the system can send recorded speech messages to pre-programmed
telephone numbers.
The control unit and expanders also provide sets of connectors for outputs,
which the installer can use to link the control unit to siren/strobe units or
other equipment.

1. Introduction Menvier30/40/100/300
Page 2
1. Two-button Hold Up Alarm with tilt switch.
2. Two button Hold Up Alarm.
3. Four button remote control.
4. Two-way remote control.
5. Keypad (i-kp01).
6. Keypad (KEY-K01, KEY-KP01 or KEY-
KPZ01)
7. Wireless arming station.
8. Door Contact/Universal Transmitter.
9. Smoke Detector.
10. Passive Infra Red.
11. External siren/strobe.
A
B
1 2 3
5 76
4
89 10
11
Figure
1.
Peripherals

Menvier30/40/100/300 1. Introduction
Page 3
This guide covers four types of control unit: the Menvier30, Menvier40,
Menvier100 and Menvier300. A complete system using one of these control
units comprises:
Control unit
Menvier3
0
Menvier4
0:
Menvier1
00:
Menvier3
00:
Fixed detectors
30
40
100
300
External Siren/Strobe
4
5
10
20
Users
50
100
250
500
Portable 4-button remote
controls (one per user)
50
100
250
500
Portable two-button hold up
alarms (one per user)
50
100
250
500
To find out which system you have see “What System Have I Got?” on
page 108.
Setting and Unsetting
The majority of alarm systems are intended to detect the movements of
people, and to notify others when people move into protected areas.
Readying the system to start an alarm when someone moves into a
protected area is called “setting” the system. Disarming the system so that
people can move freely is called “unsetting” the system.
Alarms and Reset
When the system starts an alarm it usually includes activating sounders
and strobes and sending messages to an Alarm Receiving Centre (ARC).
The ARC may then call the police or other security service to come and
investigate the alarm.
Before you can set the system again you must silence the sounders and
then “reset” the system so that it is ready for setting again (see page 15 for
instructions). Please note that your Installer may have programmed your
system so that although you can silence the sounders, you cannot reset the
system yourself. Instead you have to call the Installer to come and check
the system and reset it for you.
Security Levels
At a site where all users have complete access to the whole site, then the
installer can program the control unit to provide four levels of security: Full
Set and three different Part Sets. Any user can put the alarm system into
any of the security levels. Each security level is a collection of one or more
detectors that monitors a different area. The highest security level is called

1. Introduction Menvier30/40/100/300
Page 4
Full Set, and includes all the detectors. There are three other security
levels called Part Set B, C and D. For example, in a small shop Full Set
might monitor the whole premises, while Part Set B might monitor just the
store room. Any rear doors would normally be monitored 24 hours a day
(see “24 Hour Alarms” below).
Wards
If the system is installed at a site where some users must be restricted to
parts of the site, for example a warehouse with storage areas and separate
offices, then the installer can split the system electronically into separate
“wards”.
The Menvier300 can have up to 20 wards, the Menvier100 up to 10, the
Menvier40 up to five and the Menvier30 up to four. Users can set and unset
each ward completely independently of all the others. Individual users can
be given access to one or more wards: if they have no access to a ward
then they cannot set or unset that ward. In effect the system splits into 20
(or 10, or five or four) separate alarm systems.
In addition each ward can be programmed to set at one of two security
levels: either Full Set or Part Set. Any user who is allowed to set a ward
can select either of the two security levels.
24 Hour Alarms
The control unit can also monitor detectors continuously rather than being
set and unset. For example:
Fire and smoke detectors, flood sensors, Hold Up Alarm buttons or
emergency exits.
Monitors for machinery (for example freezers) or other type of
“technical alarm”.
These are collectively known as “24-hour alarms” because they can cause
an alarm 24 hours a day: it does not matter whether a user has set or unset
the system.
Communications
Your system may be fitted with a communication module that allows the
control unit to send alarm information over the telephone network, the
mobile phone network, or the internet. There are separate modules for
each of these different tasks.
The Installer may also be able to call into your control unit and program it
remotely. Depending on how your Installer has programmed the system