Pit Boss 10806 User manual
/ / / / 24
/ / / / 10806
| '
| |
IMPORTANT, READ CAREFULLY, RETAIN
FOR FUTURE REFERENCE. MANUAL MUST
BE READ BEFORE OPERATING!
IMPORTANT, PRENEZ CONNAISSANCE DE
CE DOCUMENT ET CONSERVEZ-LE POUR
RÉFÉRENCE ULTÉRIEURE. VOUS DEVEZ LIRE
CE GUIDE AVANT D’UTILISER LE BARBECUE!
IMPORTANTE, LEER DETENIDAMENTE,
CONSERVAR PARA REFERENCIA FUTURA.
LEA EL MANUAL ANTES DEL USO!
WICHTIG: AUFMERKSAM LESEN UND GUT
AUFBEWAHREN BITTE UNBEDINGT VOR
GEBRAUCH DIE BEDIENUNGSANLEITUNG
SORGFÄLTIG DURCHLESEN!
IMPORTANTE: LEGGERE ATTENTAMENTE E
CONSERVARE PER RIFERIMENTO FUTURO.
LEGGERE IL MANUALE PRIMA DELL'USO.
For outdoor nd household use onl Not for commercl use
Réservé l'use extéreur et résdentel unquement Non destné un use commercl
Solo pr uso doméstco en el exteror No pto pr uso comercl
Btte nur m Freen und prvt nutzen Ncht fr de ewerblche Anwendun eenet
Solo per uso domestco ed esterno Non per uso commercle
WARNING:
,
AVERTISSEMENT:
'
,
'
ADVERTENCIA:
,
,
ACHTUNG:
,
,
AVVERTENZA: '
' '
,
'
2
EN ENGLISH
COPYRIGHT NOTICE
Copyright 2021. All right reserved. No part of this manual
may be copied, transmitted, transcribed, stored in a
retrieval system, in any form or by any means without
expressed written permission of,
11 Rue Galvani Paris, France 75017
8877 North Gainey Center Drive, Scottsdale, AZ, USA 85258
www.pitboss-grills.com
Parts & Specs.......................................................................3
Assembly Preparation.......................................................4
Assembly Instructions.......................................................4
Installing The Wheels....................................................................4
Mounting The Body Bracket Handles.......................................5
Securing The Chimney ..................................................................5
Mounting The Lid Handle ............................................................5
Mounting The Door Handle.........................................................6
Installing The Air Intake Pipes ....................................................6
Securing The Side Shelf Brackets ...............................................6
Installing The Side Shelves ..........................................................7
Mounting The Thermometer ......................................................7
Installing The Charcoal Basket....................................................7
Placing The Cooking Components .............................................8
3
EN
ENGLISH
MODEL ASSEMBLED (WxDxH) WEIGHT GRIDS GRID DIAMETER COOKING AREA
24 1,357 1,300 856
/ 53.4 51.1 33.7 67.0
/ 147.7 356.1
/ 22.1 7,471
/ 1,158
Part# Description
1 Chimney Assembly (x1)
2 Thermometer (x1)
3 Lid Handle (x1)
4 Barrel Body (x1)
5 Body Bracket Handle (x2)
6 Side Shelf (x2)
7 Side Shelf Bracket - Left (x2)
8 Side Shelf Bracket - Right (x2)
9 Air Intake Pipe (x2)
10 Air Intake Silicone Pad (x2)
11 Hanging Rack (x1)
12 Cooking Grid (x3)
13 Heat Diffuser Plate (x1)
14 Charcoal Basket (x1)
15 Charcoal Tray (x1)
16 Door Handle (x1)
17 Wheel (x2)
A Wheel Axle Pin (x2)
B Wheel Washer (x2)
C Wheel Cotter Pin (x2)
D Screw (x4)
E Screw (x14)
F Locking Washer (x4)
G Washer (x4)
H Screw (x8)
I Step Screw (x4)
NOTE: Due to ongoing product development, parts are subject to change without notice. Contact
Customer Care if parts are missing when assembling the unit.
125
4
6
7
9
8
10
3
11
14
16 12
13
17 15
4
EN ENGLISH
IMPORTANT: It is advised to read each step entirely before starting assembly on instructions. Do not tighten screws
completely until all screws for that step have been installed. Hardware combination involving a locking washer and
washer should be installed with the locking washer closest to the head of the screw.
1.
Parts Required:
1 x Barrel Body (#4)
2 x Wheel (#17)
2 x Wheel Axle Pin (#A)
2 x Wheel Washer (#B)
2 x Wheel Cotter Pin (#C)
Installation:
• Place a piece of cardboard on the floor to prevent scratching the unit
and parts during assembly.
• Insert Wheel Axel Pin through the Wheel to the base of the Barrel Body
and into the hole, as shown. From below, add a Wheel Washer, then
secure using the Wheel Cotter Pin. Repeat same installation for the
other Wheel.
NOTE: Once installed, both wheels should spin freely.
Parts are located throughout the shipping carton, including underneath the smoker. Inspect the unit, parts, and hardware blister
pack after removing from the protective shipping carton. Discard all packaging materials from inside and outside of the smoker
before assembly, then review and inspect all parts by referencing the parts list. If any part is missing or damaged, do not attempt
to assemble. Shipping damage is not covered under warranty. Contact your dealer or Pit Boss® Grills Customer Care for parts.
www.pitboss-grills.com
IMPORTANT: Using two people is necessary when assembling this unit.
Tools required for assembly: Phillips screwdriver. Tools not included.
1
17
4
17
5
EN
ENGLISH
2.
Parts Required:
2 x Body Bracket Handle (#5)
4 x Screw (#D)
4 x Locking Washer (#F)
4 x Washer (#G)
Installation:
• Insert the open end of a Body Bracket Handle into the top end of the
Body Bracket, pushing it in until the mounting holes align. Secure using
two washers, locking washers, and screws. Repeat installation for the
second Body Bracket Handle. See illustration for proper arrangement.
3.
Parts Required:
1 x Chimney Assembly (#1)
4 x Screw (#E)
Installation:
• First, twist the Chimney Cap off of the Chimney Stack. This will make
the Chimney Stack easier to install. Locate the round opening on the
top of the Barrel Lid. From the outside, secure the Chimney Stack to the
top of the Barrel Lid using four screws. The screw will fasten to the self-
clinching nut on the inside of the Barrel Lid. Note illustration 3A.
• Replace the Chimney Cap by twisting it back onto the top of the Chimney
Stack. Note illustration 3B.
NOTE: Adjust the Chimney Cap to affect the airflow inside the
Smoker. If cooking at low temperature, keep the cap more closed to
restrict airflow. If cooking at a high temperature, keep the cap more
open to increase airflow.
4.
Parts Required:
1 x Lid Handle (#3)
Installation:
• Remove the pre-installed screws, locking washers, and washers from the
Lid Handle. From the inside the Lid of the Barrel Body, insert one screw,
locking washer, and washer to protrude to the outside, then secure the
screw (from the inside) into the Lid Handle. Repeat same installation for
other end of the Lid Handle.
2
3
3
5
5
4
3
6
EN ENGLISH
5.
Parts Required:
1 x Door Handle (#16)
Installation:
• First, open the Charcoal Refill Door. Pull the end of the Door Buckles to
release the Door Buckles latch that seals the Charcoal Refill Door. Note
detail illustration 5A & 5B.
• Remove the pre-installed screws, nylon gaskets, locking washers, and
washers. From the inside the Charcoal Refill Door, insert one screw,
locking washer, and washer to protrude to the outside, then add the
nylon gasket over the protruding screw. Secure the screw (from the
inside) into the Door Handle. Repeat same installation for other end of
the Door Handle. Note illustration 5B.
6.
Parts Required:
2 x Air Intake Pipe (#9)
2 x Air Intake Silicone Pad (#10)
10 x Screw (#E)
Installation:
• Starting on one side, place an Air Intake Silicon Pad between the Air
Intake Pipe and align the mounting holes with the Barrel Body, as
shown. Then tighten each of the four screws halfway first. Secure a fifth
screw, from the inside of the Barrel Body, into the upper part of the
Air Intake Pipe. Once all five screws are mounted and aligned properly,
tighten completely.
• Repeat same installation for the other Air Intake Pipe on the opposing
side of the Barrel Body.
IMPORTANT: The bottom part of each Air Intake Pipe should be
completely sealed (once completely tightened) to avoid any chance
ofembers escapingwhilethe charcoalis lit.If therearegaps,unscrew
and attempt to reinstall again.
7.
Parts Required:
2 x Side Shelf Bracket - Left (#7)
2 x Side Shelf Bracket - Right (#8)
8 x Screw (#H)
Installation:
• Note illustration for proper arrangement. Mount one Side Shelf Bracket
to the Barrel Body using two screws. Install each screw halfway first,
then tighten completely when both screws are mounted and aligned
properly. Repeat installation for the other three Side Shelf Brackets to
the Barrel Body.
7
787
8
5
5
16
6
10
10
9
9
7
EN
ENGLISH
8.
Parts Required:
2 x Side Shelf (#6)
4 x Step Screw (#I)
Installation:
• Align and position one Side Shelf onto the Side Shelf Brackets on one
side of the Barrel Body. From underneath, secure a step screw into each
corner, as shown the detailed illustration. Repeat same installation for
the Side Shelf on the other side of the unit.
NOTE: Once installed, both Side Shelves can be raised (for use) or
lowered (for storage) with ease.
IMPORTANT: Avoid using the Side Shelves to move or lift the unit.
The weight of the unit will cause the shelves to break, which is not
covered by warranty.
9.
Parts Required:
1 x Thermometer (#2)
Installation:
• First, remove the pre-installed nut and washer from the stem of the
Thermometer.
• From the outside of the Barrel Body insert the stem of the Thermometer
from the outside, then secure into place using the washer and nut from
the inside of the Barrel Body.
NOTE: Ensure the Thermometer is rotated for readability.
10.
Parts Required:
1 x Charcoal Basket (#14)
1 x Charcoal Tray (#15)
Installation:
• First, place the Charcoal Basket onto the inset grooves of the Charcoal
Tray, as shown in illustration 10A. The Charcoal Basket will rest in these
grooves without fastening.
• Next, with the Charcoal Refill Door open, place the combined Charcoal
Basket and Tray into the base of the door. Note illustration 10B. Once
in position, close the Charcoal Refill Door and latch the Door Buckles to
seal.
8
6
6
9
2
10
10
14
15
8
EN ENGLISH
11.
Parts Required:
1 x Hanging Rack (#11)
3 x Cooking Grid (#12)
1 x Heat Diffuser Plate (#13)
Installation:
• Open the Lid of the Barrel Body. Insert the Heat Diffuser Plate into
the lowest position inside the Barrel Body, directly above the Charcoal
Basket.
NOTE: The Heat Diffuser Plate is used to disperse the direct heat
from the Charcoal Basket, creating a more even heat distribution
throughout the Barrel Body.
• Next, place the Cooking Grids into the Barrel Body, resting each grid on
the pre-mounted support brackets. Adjust the height of the support
brackets, as needed.
NOTE: To maintain the grilling performance of your Cooking Grids,
regular care and maintenance is required.
• When desired for use, remove the Cooking Grids and place the Hanging
Rack on the highest position inside the Barrel Body.
• The unit is now completely assembled.
Refer to Owner's Manual for Operating Instructions.
11
11
12
12
12
13
This manual suits for next models
1
Table of contents
Other Pit Boss Smoker manuals
Pit Boss
Pit Boss PRO Series Installation instructions
Pit Boss
Pit Boss CHAMPION PBV24CB User manual
Pit Boss
Pit Boss Competition Series User manual
Pit Boss
Pit Boss V5P1 Installation instructions
Pit Boss
Pit Boss CHAMPION PBV24CB User manual
Pit Boss
Pit Boss PRO Series Installation instructions
Pit Boss
Pit Boss PBVPS1 Parts list manual
Pit Boss
Pit Boss PBV7P1 User manual
Pit Boss
Pit Boss PLATINUM PBV5PL User manual
Pit Boss
Pit Boss PBV3G1 Installation instructions
Pit Boss
Pit Boss PBV3A1 Parts list manual
Pit Boss
Pit Boss Competition Series User manual
Pit Boss
Pit Boss PBV4PS1 Installation instructions
Pit Boss
Pit Boss PBV3P1 Parts list manual
Pit Boss
Pit Boss 7 Series Installation instructions
Pit Boss
Pit Boss PB0600SS User manual
Pit Boss
Pit Boss PBV2G1 Parts list manual
Pit Boss
Pit Boss PB2BPGG User manual
Pit Boss
Pit Boss 3 Series Installation instructions
Pit Boss
Pit Boss PBV3PU1 Installation instructions
Popular Smoker manuals by other brands
ULTRASOURCE
ULTRASOURCE 320601-E owner's manual
Smokey Bandit
Smokey Bandit Lumberjack instruction manual
Yoder Smokers
Yoder Smokers S Series installation instructions
Mayer Barbecue
Mayer Barbecue RAUCHA MS-200 PRO Assembly instructions
Outdoor Cook
Outdoor Cook MS-03 instructions
Masterbuilt
Masterbuilt 20070710 instructions
Charmate
Charmate Grady CM160-030 manual
Barton
Barton 95545 Owner's manual and safety instructions
Harvia
Harvia Flare Smoker Instructions for use and recipes
Barbeques Galore
Barbeques Galore BILLABONG OFFSET SMOKER instructions
Brinkmann
Brinkmann 140-7085-K owner's manual
Kenmore
Kenmore 125.15887800 Use and care guide
