Pitaka MagEZ Mount Qi User manual

MagEZ Mount Qi User Manual

Compatibility Notice
Package Contains
Quick Guide
Spec
Warranty
Important
Customer Service
FCC WARNING
Contents
1
1
2
10
1 1
12
13
14

MagEZ Mount Qi *1
Charging Cable *1
User Manual *1
1
The PITAKA MagEZ Mount Qi will only wirelessly charge
any Qi supported phones with a proper PITAKA MagCase
(Pro).
Wireless charging may not work when you put other
cases or stick metal plates on your phone.
Do not use the MagEZ Mount Qi to charge your wireless
charging devices that are not Qi-compatible wirelessly.
Package Contains:
Compatibility Notice:

2
Step 1: Connect the cable to the MagEZ Mount Qi’s USB
port and your car charger’s USB port. Plug the car
charger into your car’s power outlet.
Quick Guide:

3
Step 2: Install the MagEZ Mount Qi on your car
1，Installing the PITAKA Car Vent MagEZ Mount Qi
Find a safe location on the vehicle vent, slide the MagEZ
Mount Qi air vent clips into your car’s air vent.

2， Installing the Suction Cup MagEZ Mount Qi.
Find a proper location and clean the surface. Then firmly
press the suction cup and press down the suction
switcher to ensure the MagEZ Mount Qi is adhered
tightly.
*Notice: Remember to press the suction cup FIRST, then
press the suction switcher and lock to ensure that you
have tightly adhered the MagEZ Mount Qi.
2.1 Firmly press the suction cup.
4

5
a) Push down the suction switcher to lock the
mount in place.
2.3 Then the MagEZ Mount Qi is attached tightly.

6
Notice: A dashboard pad is needed when you attach it on
the car’s dashboard. Then follow the other steps as above
to install the suction cup MagEZ Mount Qi.

7
3. Installing the CD Slot MagEZ Mount Qi
Simply insert the slot mount and tighten the screw to
lock it in place
3.1 Insert the mount in the CD slot

8
3.2 Tighten the mounting screw to lock the mount in
place.
3.3 Then MagEZ Mount Qi (CD Slot) is installed well

9
Step 4: You can adjust the ball-joint rotation of the vent
mount, so your device is in either portrait or landscape
orientation. And then tighten the rotation to fix the position
until it rests firmly.
ROTATE 360°

10
Note: Fast charging will only be supported when using a
QC 3.0 adapter with an output over 18W and a USB cable
supporting 3A power output.
Items Specification
Input Voltage 5V ~9V
Input Current ≤2A
Max Output Power 10W
Transmission Distance ≤8mm
Transfer Efficiency 75% Max
Operating Temperature -10℃~30℃
Storage Temperature -20℃~60℃
Working Frequency 110KHz-205KHz
DC 9V/1.1A
DC 5V/1A
Rated Output Voltage/ Current
(Fast charging)
Rated Output Voltage/ Current
(Normal charging)
Spec:

11
The PITAKA MagEZ Mount Qi is warranted for 12
months from the date of purchase. The MagEZ Mount
Qi is warranted to be free defects in materials and
function under normal use for the lifetime of the
product. A defect is defined as an imperfection or flaw
that is produced by a manufacturing error, including
malfunction of wireless charging or surface defect, etc.
This warranty is non-transferable and covers only the
original end-user purchaser. PITAKA will only authorize
the warranty claim if the product was purchased from
the official store or authorized dealer.
Damages don’t cover those resulting from abuse, not
correctly maintained, alteration or misuse (including
disassemble, drops), abnormal wear and tear, cosmetic
damages that do not affect the functionality.
MODIFICATION: Any change or modification of this
device will void the warranty.
Exclusion
Warranty:

12
Read all instructions and warnings before using this
product. Improper use may result in product damage,
excess heat, toxic fumes, fire or explosion, for which
damages PITAKA is not responsible.
1) DO NOT DIRECT HEATED AIR FROM THE VENT ONTO
THE MOUNT WHILE IT IS ATTACHED TO THE VENT. When
running the car’s heater, make sure you close the vent
that the mount is attached to or take the mount from the
car vent directly, or direct the heated air out of the car’s
lower vents and away from the upper vents.
2) Do not keep the MagEZ Mount Qi in a
high-temperature environment, including heat caused by
intense sunlight or other forms of heat. Do not place it in
the fire or other excessively hot environments.
3) Do not disassemble the MagEZ Mount Qi or attempt to
modify it in any way.
4) Do not attempt to power the MagEZ Mount Qi with
any connection other than the Type-C connector.
Important:

13
Customer Service
5) Do not attempt to replace any part of the MagEZ Mount
Qi
6) All products have gone through a thorough quality
assurance inspection. If you find that your MagEZ Mount
Qi is excessively hot, is emitting odor, is deformed,
abraded, cut or is experiencing or demonstrating an
abnormal phenomenon, immediately stop all product use
and contact Manufacturer.
7) If this MagEZ Mount Qi is intended by the purchaser to
be used by a minor, purchasing adult agrees to provide
detailed instructions and warnings to any minor before
use. Failure to do so is the sole responsibility of the
purchaser, who agrees to indemnify Manufacturer for any
unintended use/misuse by a minor.
Phone：[phone]
E-mail: [email protected]
Website: www.ipitaka.com

14
FCC WARNING:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation.

15
If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician
for help.
The device has been evaluated to meet the general RF
exposure requirement.
FCC ID: 2ARI5-CM3001Q