Pittasoft Pitta 310 User manual

Network IP Camera
Pitta 310
user manual

FCC notice to users and product statements
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions;
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum 20 cm between the
radiator and your body. This transmitter must not be collocated or operation in conjunction with
any other antenna or transmitter unless authorized to do so by the FCC.

Contents
Chapter 1. Getting Ready
Before Using This User Manual................................2
Pitta 310 Overview ...................................................3
Checking the Pitta 310 Package Content.................4
Checking the main body of the Pitta 310..................5
Installing the Pitta 310 ..............................................6
Connecting Pitta 310 ................................................7
Installing the Software ..............................................9
Chapter 2. Pitta IP Utility and Pitta Web View
Pitta IP Utility guide.................................................11
changing IP address...............................................12
Pitta WebView Log-in .............................................14
Pitta WebView Live View Page...............................15
Pitta WebView-Setup Menu....................................17
Chapter 3. Appendix
DDNS & Router Port Forwarding............................26
Troubleshooting ......................................................27
6SHFL¿FDWLRQ ...........................................................28
Dimension...............................................................30

2PITTASOFT
Getting Ready
Before Using This User Manual
Thanks for purchasing our Pitta 310 IP Network Camera. This is a user manual for
H.264 IP Network Camera and the product mentioned here designates the H.264 IP
Network Camera. Please go through the manual before installation and use of the camera.
This manual along with the software and hardware explained here is protected by
copyright law
.
xRead through all printed documentation and ensure that your system is compatible for
your product.
xPittasoft will continue to add new functions and enhancements and apply new
WHFKQRORJLHVWRWKLVSURGXFW$Q\LQIRUPDWLRQDQGVSHFL¿FDWLRQVFRQWDLQHGLQWKLVPDQXDO
can be changed without prior notice to users.
x7KHVFUHHQVKRWVDQG¿JXUHVSUHVHQWHGLQWKLVPDQXDOPD\GLIIHUIURPWKHDFWXDO
appearances of the product.
❚Conventions
Icon Name Meaning
]
Caution Indicates that the accompanying function may not operate or be
disabled.
✎
Note Indicates a tip or supplementary description to help you operate the
accompanying function.

3
PITTASOFT
Getting Ready
Pitta 310 Overview
The Pitta 310 series are high-tech IP Network Cameras that use H.264 codec technology to
achieve high compression rates and clear picture quality by allowing for high frame rates to
be transmitted through the network. By using the network, remote connection, monitoring,
and control are possible from any location for simple use. The Pitta 310 series IP Network
Camera guarantees performance and safety while offering various solutions through internet
integration.
❚Specifications
High quality H.264 video
+HQDEOHVH[FHOOHQWLPDJHTXDOLW\DWVLJQL¿FDQWO\UHGXFHGQHWZRUNEDQGZLGWKDQG
storage.
Support WDR (Wide Dynamic Range)
Built-in progressive CMOS image sensor and support better image in backlight
environment than normal sensor. (Pitta 310R/310WR supports only)
Motion Detection
Intelligent Motion Detection analyzes for any motion in the scene. The reliable
functionality is built into the camera and client software. Using the client software, user
can set up motion detection to trigger video recording and e-mail alerts. Particular area
in the scene could be included or excluded for the motion detection.
Auto correction of lens distortion
Pitta 310 series client software automatically correct distorted images and can deliver
near perfect images.
Compact size & ultra-light weight
Pitta 310 series are compact design and require minimum space for the installation and
UHGXFHGZHLJKWDOORZVÀH[LEOHPRXQWLQJ
Supports WiFi
Wireless LAN(WiFi) provides easy installation without wired network. (Pitta
310W/310WR supports only)
Supports Audio
Built-in microphone provides recording the surrounding sounds.

4PITTASOFT
Getting Ready
Checking the Pitta 310 Package Content
Check the product and the accompanied accessories contained in the product package.
xIf there is any problem with the accessories, contact your local product distributor.
xThe accompanied accessories can be changed without prior notice.
Pitta 310
Stand
AC adaptor Antenna (Pitta 310W/310WR)
User manual Installation CD (Pitta View, IP Utility)
zGGO]lhP
shuGj

5
PITTASOFT
Getting Ready
Checking the main body of the Pitta 310
Check the main body of the Pitta 310.
✎Description is based on Pitta 310W / 310WR.
✎The figures presented may differ from the actual appearances of the product.
1Front LED Red: Booting Orange: Starting
Green: Operating Red blinking: Firmware upgrading
2AUDIO IN/OUT
IN: Audio input port. You can connect a microphone.
(Check the sound with a PC)
OUT: Audio output port. You can connect a speaker. (This feature is not
LPSOHPHQWHG,WZLOOEHH[SHFWHGWRDGGWKLVIHDWXUHDIWHU¿UPZDUH
upgrade.)
3WIRELESS ON/
OFF
Wireless ON/OFF switch. Make sure that the switch is ON if wireless
needs.
4ANTENNA Wireless port. Connect the antenna for wireless installation.
5LAN Connect the 10/100 Mbps Ethernet cable. Make sure that use RJ-45
connector. Supports PoE (IEEE 802.3af)
6RESET Press the reset button for 3 seconds then all the settings will be changed
to initial settings.
7DC IN DC 5V / 1.0A power terminal.
8NETWORK LED LED is blinking when network is connected.
9POWER LED LED is blinking when power is on.
0Built-in microphone Built-in microphone location.
1 2 3
567
8 9 0
4

6PITTASOFT
Getting Ready
1 Connect the camera to the stand.
✎Connect the antenna to the camera for Pitta 310W
/ 310WR.
2 Place a camera stand at the intended place.
xMake sure that the LAN cable and power
PXVWEH¿JXUHGDWWKHLQWHQGHGSODFH
3 Connect the LAN cable and AC adaptor.
4 Adjust the camera angle.
Installing the Pitta 310

7
PITTASOFT
Getting Ready
❚For wired camera
1 Connect the LAN cable to the [LAN] port.
✎Use a cross cable for a direct connection between
the PC and the camera only. Use direct LAN
cable for using a router or switch hub.
2 Connect the AC adaptor to the [DC] terminal.
✎Use the provided AC adaptor.
3 Make sure that POWER LED and NETWORK
LED is on.
Connecting Pitta 310
- AUDIO - WIRELESS
IN
DC IN LAN
RESET ANTENNA
OUT ON OFF

8PITTASOFT
Getting Ready
Connecting Pitta 310
❚For wireless camera
To connect the wireless camera, IP setting and wireless setting must be set before using.
Once set up is done, disconnect the LAN cable and connect the wireless camera.
1 Connect the camera with the LAN cable.
(T page 7)
2 Set IP address. (T pages 12~13)
3 6HWZLUHOHVVFRQ¿JXUDWLRQLQ3LWWD:HE9LHZ
(T page 19)
4 Disconnect the LAN cable.
5 Connect the antenna.
6 Turn on the WIRELESS switch.
✎Make sure that NETWORK LED is blinking after
about 1 minute.
7 Disconnect and reconnect the AC adaptor. The
camera will reboot.
8 Check the IP address with the Pitta IP Utility.
✎If the connection is change to wireless, IP address may change and the router may need to
restart.

9
PITTASOFT
Getting Ready
Install the Pitta IP Utility and Pitta View software.
1 ,QVHUWWKHLQVWDOODWLRQ&'LQWRWKH&'GULYH'RXEOHFOLFNWKH6HWXSH[H¿OHRQWKH&'
✎You can download this file from Pittasoft homepage (www.pittasoft.com).
2 Follow the instructions on the installation program to complete.
3 Check the Pitta IP Utility and Pitta View icon is created.
4 Double click the shortcut icon to start the software.
Installing the Software

10 PITTASOFT
Getting Ready
Installing the Software
❚System requirement
CPU Intel Pentium4 2.0Ghz or higher
RAM Minimum 1GB (Recommanded 2GB)
Network Ethernet
Graphic Card
1024X768, 24bit color
128MB RAM (Recommanded 256MB higher)
DirectX 9.0 or newer support, Direct Draw Overlay Support
HDD Type E-IDE, SATA, SCSI, SAS
HDD Space Minimum 80GB Free
O/S Windows XP SP2, Windows Vista
❚Re-installation
If reinstallation is needed, current software has to be uninstalled.
1 To uninstall the software, click on uninstall button in;
>6WDUW@ĺ>$OOSURJUDPV@ĺ3LWWDVRIWĺ8QLQVWDOO
2 Re-install the software.
xPitta IP Utility
This software is for assigning IP address to many cameras at once. (See chapter 2)
xPitta View
This software is the multi-channel network video recorder.
(See Pitta View user manual)

11
PITTASOFT
Pitta IP Utility and Pitta Web View
Pitta IP Utility guide
Use Pitta IP Utility to change or verify the IP address of the camera.
❚Pitta IP Utility menu
Menu Features
File Exit Close the Pitta IP Utility.
View
Toolbar Shortcut buttons.
Status Bar Displays current status 4.
Home Page Go to Pitta WebView home page.
Properties ✎This feature is an additional plan.
Refresh Refresh the camera list.
Tools
Assign IP address to
the selected device Change IP address.
Assign IP address
using serial number Change IP address by serial number.
Test IP address Testing for the selected camera.
Help About PittaIPUtility Displays Pitta IP Utility information.
3 Camera List
4 Status bar
1 Menu 2 Toolbar (Shortcut)

12 PITTASOFT
Pitta IP Utility and Pitta Web View
changing IP address
❚Change IP address by selecting camera
1 Start Pitta IP Utility.
Select the camera whose IP address needs to
be changed.
2 Click button.
'Assign IP address', pop-up window appears.
3 Enter User ID and Password.
✎Default initial values of administrator's ID and
Password are admin/admin. You can change
ID, Password in Pitta WebView. (T page 18)
4 Assign the IP address.
xObtain an IP address automatically(DHCP): Use this to assign the IP address of the
camera automatically.
xUse the following IP address: Use this to assign the IP address of the camera
manually.
5 Press 'Assign' button
6 Press button to refresh the camera list.

13
PITTASOFT
❚Change IP address by serial number
1 Start Pitta IP Utility
2 Click button. 'Assign IP address', pop-up
window appears.
3 Enter User ID, Password, Serial Number.
✎Default initial values of administrator's ID and
Password are admin/admin. You can change
ID, Password in Pitta WebView. (T page 18)
✎Camera Serial Number is located in the back of
the product.
4 Set equal to 4 ~ 6 step page 12.
✎Factory default setting is the DHCP mode : IP address will be automatically assigned.
✎If you use Pitta IP Utility with cross cable connection, you must assign the static IP. Please do not
use DHCP option with cross cable.
✎Pitta 300 series software applications work with Windows XP SP2 and Windows Vista on Internet
Explorer 5.0 or later.
✎This application can be used if the camera is physically connected in the same Subnet only.
Otherwise, access the camera using Pitta WebView by directly connecting the camera to the PC
using a cross cable and then change the IP address in the Pitta WebView Network Settings. (T
page 18)
✎IP setting using DHCP could take up to maximum 10 minutes.

14 PITTASOFT
Pitta IP Utility and Pitta Web View
Pitta WebView Log-in
Pitta WebView is the role of each camera's homepage. Set the camera or live view is
possible through the internet.
1 Connect to the camera's homepage.
xMethod 1: To open Login page, enter IP
address in the address bar of your web
browser and press Enter.
xMethod 2: Select the camera and press the
button in Pitta IP Utility.
- Double-click on the camera or click the
mouse right button and choose 'Home Page'
then you can go to the login page.
6HOHFWWKH9LHZĺ+RPHSDJHIURP0HQX
bar then you can go to the login page.
2 Enter user ID and Password and press 'Log in'
button.
xDefault initial values of administrator's ID and
Password are admin/admin
x,I\RXORJLQWR/LYH9LHZDW¿UVWWLPHD\HOORZ
bar will appear at the top of the screen.
Please click on the yellow bar and continue
to install the 'PTAMME_X ActiveX Control
Module'.
]If you have accessed by administrator account, you
may change the password of administrator to ensure
the security of the system. (T page 18)
]In this case, the access by the Guest should
be approved by the administrator. (T page 18)

15
PITTASOFT
Pitta IP Utility and Pitta Web View
Pitta WebView Live View Page
❚LiveView
Press button. This is the live view mode.
NO. Item Features
1Address You can check the IP address of the camera.
2Homepage shortcut Open Pittasoft homepage.
3Live view Live view screen.
4Current Time Displays current time. Time can be set in Setup page. (T page 24)
5Volume Adjust the volume. Make sure that Audio Feature is enable. (T page 17)
6Save the image in JPEG or BMP.
7Full screen.
8Play and Stop.
1
3
876
2
4
5

16 PITTASOFT
Pitta IP Utility and Pitta Web View
Pitta WebView Live View Page
❚Setup
Press button.
Basic setting page.
✎For more information, see page 17~25.
❚Help
Press button
Pitta WebView help page.
✎Press the 'Help' button on the setup page to get
help and tips for the current page.
❚Logout
Press button. You can use this to logout.

17
PITTASOFT
Pitta IP Utility and Pitta Web View
Pitta WebView-Setup Menu
❚Basic
Camera Name Camera Name for assigning a name to the camera. Available to use up to 64
letters.
Resolution Use this to set the size of image.
xD1(720X480)/VGA(640X480)/CIF(352X288)/QVGA(320X240)/QCIF(176X144)
Rotation Use this to rotate the display by 180°.
x0(floor)/180(Invert)
Night Mode Use this to get the better video quality in dark places.
Video Quality Use this to choose video display quality.
xHighest(3Mbps)/High(2Mbps)/Normal(1Mbps)/Low(500Kbps)/Lowest(300Kbps)
Frame Rate
Use this to set the number of frames to be transmitted from the camera per
second.
x10 fps/15 fps/20 fps/25 fps/30 fps
Motion Detection Enable the Motion Detection. Default is enabled. For more information, see
page 21.
Audio Enable Audio On / Off.

18 PITTASOFT
Pitta IP Utility and Pitta Web View
Pitta WebView-Setup Menu
❚Advanced
1User
Change Admin's ID and Password.
Change User ID, Password and authority.
✎You can use up to 4~32 (A-Z, a-z, 0-9,. _
available) and 4~10 (available to use all
characters) to make ID and Password,
respectively.
✎Default initial values of administrator's ID and
Password are admin/admin.
✎If you forgot ID/Password, press 'RESET' button to initial setting. (admin / admin)
All the settings will be changed to initial setting.
2Network Settings
2 - 1IP and Ports
Camera IP address setting page. It's equivalent to IP Utility setting. (T pages 12~13)
✎Also use this setting for the camera is set in different subnet mask.
ⵐIP and Port Setting
xObtain an IP address automatically: Use
this to assign the IP address of the
camera automatically.
xUse the following IP address: Use this
to assign the IP address of the camera
manually.
xVideo Port No: Enter Video Port
number. Default is 50001.
xWeb Port No: Enter Web Port number.
Default is 80.