Bosch LTC 0510 Series User manual

Video | LTC 0510 Series DinionXF Monochrome Cameras
LTC 0510 Series DinionXF Monochrome
Cameras
www.boschsecurity.com
u15-bit DSP technology
uXF-Dynamic
uBilinx communication
uDefault shutter
uLens wizard
The LTC 0510 Series of High Performance 1/2-inch
Digital CCD Monochrome Cameras create the best
possible image, even under the most difficult light and
scene conditions. Based on unique 15-bit digital video
processing technology and employing XF-Dynamic,
these cameras provide the ultimate sensitivity with
extended dynamic range. By employing the best 1/2-
inch CCD available, advanced front end processing,
combined with the outstanding Dinion DSP, the
cameras achieve an astonishing sensitivity, providing
better images in low light situations and sharper
daytime images.
All Dinion cameras are supplied ready to operate.
Simply attach and focus the lens, and connect power
to provide optimal pictures under virtually all scene
conditions. No tools are required for back focus and
power connection. For extra challenging situations
where fine tuning or special settings are required, the
camera parameters can be individually set using the
control buttons on the side of the camera and On-
screen Display (OSD). Also, to aid installation, the
camera automatically detects the lens type, and using
the Lens Wizard ensures accurate (back) focusing for
perfectly sharp pictures at all times.
Functions
XF-Dynamic
Extended dynamic range is brought to a new level on
the LTC 0510 Series Camera by XF-Dynamic
technology. XF-Dynamic automatically processes the
highly accurate 15-bit digital signal to optimally
capture the detail in both the highlight and lowlight
areas of the scene simultaneously, to maximize the
information visible in the picture.
Bilinx Technology
The LTC 0510 series cameras incorporate Bilinx. Bilinx
is a bidirectional communication capability embedded
in the video signal of all Bosch Dinion cameras. With
Bilinx technicians can check status, change camera
settings and even update firmware from virtually
anywhere along the video cable. Bilinx reduces service
and installation time, provides for more accurate setup
and adjustment, and improves overall performance. In
addition, Bilinx uses the standard video cable to
transmit alarm and status messages, providing
superior performance without additional installation
steps.

Video Motion Detection
The built-in video motion detector allows you to select
up to four fully programmable areas with individual
thresholds. The global scene change detector
minimizes false alarms caused by sudden lighting
condition changes, such as switching on or off the
indoor or security lighting. When motion is detected
alarms may be displayed in the video signal, the output
relay can be closed in addition to alarm message
transmission on Bilinx.
Auto Black
The automatic black level feature, enhances contrast
by removing veiling glare from the picture or when
contrast is reduced by fog or mist.
Default Shutter
When viewing moving objects a fast shutter speed is
required. When using a fast shutter speed the lens
opening or gain control needs to be increased to
maintain the video signal. The camera sensitivity is
limited by the fast shutter speed. The default shutter
setting of the LTC 0510 offers the best of all worlds,
fast shutter speed as long as there is sufficient light,
however as the light level falls, when other
adjustments have been exhausted, the shutter reverts
to the standard setting maintaining the cameras
excellent sensitivity.
Back Light Compensation (BLC)
Offering a fully programmable BLC area of interest,
and a variable BLC level, the camera can be easily set
up for even the most challenging entrance
applications.
Lens Wizard
The LTC 0510 series automatically detects the type of
lens installed. The Lens Wizard will focus the lens at
the maximum lens opening, to ensure that focus is
maintained throughout the entire 24-hour day/night
cycle. No special tools or filters are required.
Programmable Modes
The camera supports 3 independent operating modes.
The 3 modes are preprogrammed for typical
applications, but are fully programmable for individual
situations. Switching between modes is easy via Bilinx
or the external alarm input.
SensUp
By increasing the integration time on the CCD up to 10
times, the effective sensitivity is dramatically
enhanced, especially useful where there is no artificial
lighting and you rely on the moon, stars and scattered
radiation.
Certifications and approvals
Electromagnetic Compatibility
Emission EN55022 class B, FCC class B part 15
Immunity EN50130-4 Alarm Systems, Part 4
Vibration Camera with 500 gr (1.1 lbs) lens according to
IEC60068-2-27
Safety
EN60065 (/10 and /50 models)
UL6500, cUL CAN/CSA E60065-00 (/20 and /60 models)
Region Certification
Europe CE EC-Declaration of Conformity
Installation/configuration notes
Dimensions in mm
Parts included
Quantit
y
Component
1LTC 0510 Series DinionXF Monochrome Camera
1 Spare male 4–pin lens connector
Lens not included
Technical specifications
Electrical
Model No. Voltage Range System
LTC 0510/10 12 – 28 VAC
11 – 39 VDC
45 – 65 Hz CCIR
LTC 0510/20 12 – 28 VAC
11 – 39 VDC
45 – 65 Hz EIA
LTC 0510/50 85 – 265 VAC 45 – 65 Hz CCIR
LTC 0510/60 85 – 265 VAC 45 – 65 Hz EIA
Power Consumption 4 W
Imager Interline transfer CCD, 1/2-inch image
format
2 | LTC 0510 Series DinionXF Monochrome Cameras

Active Pixels
CCIR Models: 752 H x 582 V
EIA Models: 768 H x 492 V
Sensitivity (3200 k)
Sensitivity (Full video)1) 0.16 lux (0.016 fc)
Sensitivity 50 IRE1) 0.032 lux (0.0032 fc)
Minimum Illumination1) 0.021 lux (0.0021 fc)
Minimum Illumination
with Sense Up
0.0021 lux (0.00021 fc)
Horizontal Resolution 570 TVL
Signal-to-Noise-Ratio > 50 dB
Video Output 1 Vpp, 75 ohm
Synchronization Internal, line lock or genlock selectable
Electronic Shutter Auto (1/60 (1/50) to 1/500000), fixed,
flickerless, default
Sensitivity Up Off, automatic continuous up to 10x
Auto Black On, off selectable
Range 32x dynamic range enhancement
Dynamic Noise
Reduction
Auto, off selectable
Contour Sharpness enhancement level selectable
BLC Off, area and level selectable
Gain Auto (maximum level selectable to 28 dB)
or fixed level selectable
VMD 4 area, sensitivity selectable
Alarm Output VMD or Bilinx
Alarm Input(TTL) Profile switching, +5 V nominal,
+40 VDC max
Alarm Output Relay max. 30 VAC or +40 VDC, max. 0,5 A
continuous, 10 VA
External Synchronal
Input
75 ohm or High Impedance selectable
Cable Compensation Up to 1000 m (3000 ft) coax without
external amplifiers (automatic set-up in
combination with coaxial communication)
Camera ID 16 character editable string, position
selectable
Lens Types Manual, DC- and Video-Iris auto-detect with
override.
DC-iris drive: max 50 mA continuous
Video-iris: 11.5 ± 0.5 VDC, max. 50 mA
continuous
Remote Control Bi-directional coaxial communication
1) F/1.2, 89% reflection, SenseUp off
Mechanical
Dimensions (H x W x L) 59 x 67 x 122 mm (2.28 x 2.6 x 4.8 inch)
without lens
Weight 450 g (0.99 lbs) without lens
TripodMount Bottom (isolated) and top 1/4-inch
20 UNC
LensMount C and CS
Controls OSD with softkey operation
Environmental
OperatingTemperature -20°C to +50°C (-4°F to +122°F)
StorageTemperature -25°C to +70°C (-13°F to +158°F)
OperatingHumidity 20% to 93% RH
StorageHumidity up to 98% RH
Ordering information
LTC 0510/10 DinionXF Monochrome Camera
1/2-inch B/W high performance CCIR, 570 TVL, 12-28
VAC/11-39 VDC, 50 Hz
Order number LTC0510/10
LTC 0510/50 DinionXF Monochrome Camera
1/2-inch B/W high performance CCIR, 570 TVL, 85-265
VAC, 50 Hz
Order number LTC0510/50
LTC 0510/60 DinionXF Monochrome Camera
1/2-inch B/W high performance EIA, 570 TVL, 85-265
VAC, 60 Hz
Order number LTC0510/60
Accessories
LTC 3283/20 Zoom Lens
1/2-inch, 8.0 – 48 mm, Video-iris, CS-mount F1.4-360,
4-pin
Order number LTC3283/20
LTC 3274/41 Varifocal Lens
1/2-inch, 7.5 – 75 mm, DC-iris, C-mount, F1.7-360, 4-
pin
Order number LTC3274/41
TC120PS Power Supply Unit
Order number TC120PS
TC220PS Power Supply Unit
Order number TC220PS
TC220PSX‑24 Power Supply Unit
Order number TC220PSX-24
TC1334 Power Supply Unit
Order number TC1334
3 | LTC 0510 Series DinionXF Monochrome Cameras

Software Options
VP‑CFGSFT Configuration Software
for cameras using Bilinx, includes VP-USB Adaptor
Order number VP-CFGSFT
4 | LTC 0510 Series DinionXF Monochrome Cameras
Represented by:
Americas: Europe, Middle East, Africa: Asia-Pacific: China: America Latina:
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: [phone]
Fax: [phone]
[email protected]
www.boschsecurity.us
Bosch Security Systems B.V.
P.O. Box 80002
5617 BA Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: [phone]
[email protected]
www.boschsecurity.com
Robert Bosch (SEA) Pte Ltd, Security
Systems
11 Bishan Street 21
Singapore 573943
Phone: [phone]
Fax: [phone]
[email protected]
www.boschsecurity.asia
Bosch (Shanghai) Security Systems Ltd.
201 Building, No. 333 Fuquan Road
North IBP
Changning District, Shanghai
200335 China
Phone [phone]
Fax: [phone]
www.boschsecurity.com.cn
Robert Bosch Ltda Security Systems Division
Via Anhanguera, Km 98
CEP 13065-900
Campinas, Sao Paulo, Brazil
Phone: [phone]
Fax: [phone]
[email protected]
www.boschsecurity.com
© Bosch Security Systems 2013 | Data subject to change without notice
2001146123 | en, V2, 04. Oct 2013