2
Chase effects
This section describes each of the 31 internal chase
effects that are selectable either via the control menu
(prog > c1/c2 > EFEC) or using DMX values sent
from an external source. To use the internal effects,
set the mode option either to ef m (to control effects
via the menu) or 4+E (to control effects externally via
DMX). See page 4 for details about controlling effects
on other fixtures via DMX without using a control desk.
DMX EFEC Chase effect description
value value
0-7 00 Off
8-15 01 Rainbow chase forward
16-23 02 Rainbow chase reverse
24-31 03 10/90 duty cycle strobe white
32-39 04 10/90 duty cycle strobe white
40-47 05 10/90 duty cycle strobe white
48-55 06 50/50 duty cycle strobe white
56-63 07 50/50 duty cycle strobe red
64-71 08 50/50 duty cycle strobe blue
72-79 09 50/50 duty cycle strobe yellow
80-87 10 50/50 duty cycle strobe green
88-95 11 Pulse strobe white
96-103 12 Pulse strobe blue
104-111 13 Pulse strobe rainbow
112-119 14 Pulse strobe red/green/blue
120-127 15 Primary/secondary chase
128-135 16 Rainbow chase
136-143 17 Yellow/blue chase
144-151 18 Rainbow chase
152-159 19 Yellow/blue chase
160-167 20 Red/blue chase
168-175 21 Red/green chase
176-183 22 50/50 duty cycle fade red
184-191 23 50/50 duty cycle fade green
192-199 24 50/50 duty cycle fade blue
200-207 25 Static orange
208-215 26 Static yellow
216-223 27 Static light blue
224-231 28 Static purple
232-239 29 Static red
240-247 30 Static green
248-255 31 Static blue
Channel layouts within operation modes
The table below shows how colour mixing, chase effects and master intensity
controls are mapped to DMX channels for each mode. Mode dmx does not
use chase effects. In all modes, the first channel of the fixture occurs at the DMX
address selected using addr and successive channels for the fixture follow from
there.
Note: The PERS >RES option determines the number of channels required
within DMX mode. There is a 16BT option which does not operate, do not select
this option.
Channel dmX (RES=3CH))dmX (RES=4CH)4+E (Wash)
1 Red Red Red
2 Green Green Green
3 Blue Blue Blue
4 Master intensity* Amber Amber
5 - Master intensity* c1 Effect
6 - - c1 Speed
7 - - c1 Xfade
8 - - c2 Effect
9 - - c2 Speed
10 - - c2 Xfade
11 - - Master int.
*Master intensity for dmx mode is available only when the pers > mint
option is set to on.
Using the menu
• When not in the menu, the four digit display shows the
current DMX address e.g. A001. Some of the display’s
decimal points are used to indicate status (see below).
• Press to enter the menu. The four digit display will show ADDR.
• Use and to move between menu options (or to change a
value within an option).
• Press to enter an option (or to fix a changed value within an
option and return to the previous option level). Note: If you do
not press to fix a value, operation will revert to the
previously set mode at the next power on.
• Press to exit from a menu option (and eventually
exit the menu completely).
General notes
• Ensure that only one DMX
device in the chain is set
as master (e.g. the lighting
desk). This fixture is usually
set to slave mode.
• This fixture is shipped with
the DMX address set to
001.
• The four digit display can
be set to switch off when
not in use. To restore, press
. To alter this mode use:
PERS >DISP.
Menu operation
