2
Chase effects
This section describes each of the 31 internal chase effects
that are selectable either via the control menu (prog >
c1/c2 > EFEC) or using DMX values sent from an exter-
nal source. To use the internal effects, set the mode option
either to ef m (to control effects via the menu) or EF d/
MAX1/MAX2 (to control effects externally via DMX). See
page 4 for details about controlling effects on other fixtures
via DMX without using a control desk.
DMX EFEC Chase effect description
value value
0-7 00 Off
8-15 01 Rainbow chase forward - 3 cell split
16-23 02 Rainbow chase reverse - 3 cell split
24-31 03 White single cell chase forward
32-39 04 White single cell chase reverse
40-47 05 Double bouncing cells - centre to edge
48-55 06 50/50 duty cycle strobe white
56-63 07 50/50 duty cycle strobe red
64-71 08 50/50 duty cycle strobe blue
72-79 09 50/50 duty cycle strobe yellow
80-87 10 50/50 duty cycle strobe green
88-95 11 Pulse strobe white
96-103 12 Pulse strobe blue
104-111 13 Pulse strobe rainbow
112-119 14 Pulse strobe red/green/blue
120-127 15 Primary/secondary chase
128-135 16 Rainbow chase
136-143 17 Yellow/blue chase
144-151 18 Rainbow chase
152-159 19 Yellow/blue alternate cell chase
160-167 20 Red/blue alternate cell chase
168-175 21 Red/green chase
176-183 22 50/50 duty cycle fade red
184-191 23 50/50 duty cycle fade green
192-199 24 50/50 duty cycle fade blue
200-207 25 Static orange
208-215 26 Static yellow
216-223 27 Static light blue
224-231 28 Static purple
232-239 29 Static red
240-247 30 Static green
248-255 31 Static blue
Channel layouts within operation modes
The table below shows how colour mixing, chase effects and master intensity controls
are mapped to DMX channels for each mode. The dmx and16bt modes do not
use chase effects. In all modes, the first channel of the fixture occurs at the DMX ad-
dress selected using addr and successive channels for the fixture follow from there.
Note: The PERS >RES option determines the number of channels required within
DMX and16bt modes (16bt uses twice the number of channels setup within RES).
Chan. dmX) dmX 16bt) 16bt MAX1 MAX2
(RES=3CH) (RES=9CH) (RES=3CH) (RES=9CH)
1 Red Red (cell1) Red (crse) Red (cell1,crse) Red (cell1) Red
2 Green Grn. (cell1) Red (fine) Red (cell1,fine) Green (cell1) Green
3 Blue Blue (cell1) Grn. (crse) Grn. (cell1,crse) Blue (cell1) Blue
4 Mast int.* Red (cell2) Grn. (fine) Grn. (cell1,fine) Red (cell2) c1 Effect
5 - Grn. (cell2) Blue (crse) Blue (cell1,crse) Green (cell2) c1 Speed
6 - Blue (cell2) Blue (fine) Blue (cell1,fine) Blue (cell2) c1 Xfade
7 - Red (cell3) Master int.* Red (cell2,crse) Red (cell3) c2 Effect
8 - Grn. (cell3) - Red (cell2,fine) Green (cell3) c2 Speed
9 - Blue (cell3) - Grn. (cell2,crse) Blue (cell3) c2 Xfade
10 - Master int.* - Grn. (cell2,fine) c1 Effect Mast. int.
11 - - - Blue (cell2,crse) c1 Speed -
12 - - - Blue (cell2,fine) c1 Xfade -
13 - - - Red (cell3,crse) c2 Effect -
14 - - - Red (cell3,fine) c2 Speed -
15 - - - Grn. (cell3,crse) c2 Xfade -
16 - - - Grn. (cell3,fine) Mast. int. -
17 - - - Blue (cell3,crse) - -
18 - - - Blue (cell3,fine) - -
19 - - - Master intensity.* - -
*Master intensity for dmx and16bt modes are available only when the
pers > mint option is set to on.
crse = Course (high) channel for 16-bit, fine = Fine (low) channel for 16-bit
Using the menu
• When not in the menu, the four digit display scrolls the
current DMX address and mode. The display’s right hand
decimal point (data dot) is used to indicate status (see below).
• Press to enter the menu. The four digit display will show ADDR.
• Use and to move between menu options (or to change a
value within an option).
• Press to enter an option (or to fix a changed value within an
option and return to the previous option level). Note: If you do
not press to fix a value, operation will revert to the
previously set mode at the next power on.
• Press to exit from a menu option (and eventually
exit the menu completely).
General notes
• Ensure that only one DMX
device in the chain is set
as master (e.g. the lighting
desk). This fixture is usually
set to slave mode.
• This fixture is shipped with
the DMX address set to
001.
• The four digit display can
be set to switch off when
not in use. To restore, press
. To alter this mode use:
PERS >DISP.
Menu operation
