Pixelfly NEX-MC10 User manual

Quick Start Guide
NEX-MC10
This guide is for quick installation only.
For complete user manual go to www.avpixelfly.com or use a
QR reader to access the manual via QR code below.
Scan QR code with your Smart-phone or Tablet.

2

3
NEX-MC10 is an IP control box that used as an A/V control
device for controlling, configuring and managing encoders and
decoders on the local area network.
Packing List
•1 x IP Control Box
•1 x DC 12V Power Adapter (with US, UK, EU, AU pins)
•1 x Phoenix Male Connector (3.5 mm, 6 Pins)
•2 x Mounting Brackets (with Screws)
•5 x Label Cards (49 mm x 15 mm)
•1 x Quick Start Guide (This Document)
Panel Description
Front Panel
4321
No.
Name
Description
1
Label Card
Location
Insert a supplied label card intended for writing
short notes such as an IP address.
2
STATUS
LED
Blue: The device is working properly.
Off: The device is powered off or is booting.
3
POWER
Red: The device is powered on.

4
No.
Name
Description
LED
Off: The device is powered off.
4
RESET
When the device is powered on, use a pointed
stylus to hold down RESET button for five or more
seconds, and then release it. It will reboot and
restore to its default settings.
Note: When the default settings are restored,
your custom data is lost. Therefore, exercise
caution when using the RESET button.
Rear Panel
3
1 2
No.
Name
Description
1
LAN 1-2
1 x LAN1 (AV/POE):
Connects to a switch for communication with
encoders and decoders on the same network.
Default Protocol
IPAddress
169.254.1.1
Subnet mask
255.255.0.0
Gateway
169.254.1.254
DHCP
Off
Link speed
and duplex
Auto detected
Ethernet port indicators :
Green Link LED: this green colored LED
lights when the device actively communicates
with a network.
Amber Activity LED: this amber colored

5
No.
Name
Description
LED flickers as the device is connected to a
network.
1 x LAN2 (C):
Connects to a third-party controller for controlling,
configuring and managing the device, encoders
and decoders through LAN control (Web GUI &
Telnet).
Default Protocol
IPAddress
192.168.11.24
3
Subnet mask
255.255.0.0
Gateway
192.168.11.1
DHCP
Off
Link speed
and duplex
Auto detected
Ethernet port indicators : same as above.
Note:
•Only LAN1 (AV/POE) port supports PoE.
You can connect it to a PoE switch to
receive power, eliminating the need for a
nearby power outlet.
•We would recommend that you power this
device using either a power adapter or a
PoE switch instead of using both them at the
same time. For example, if you want to use
a power adapter, ensure that PoE function of
the connected LAN port in the switch is
disabled or a non-PoE switch is used.
2
RS-232
Left (DEBUG): Pins TX, RX, G are used for
device troubleshooting only.
RS232 Parameters
Baud Rate
115 200 bps
Data Bits
8 bits
Parity
None
Stop Bits
1
Middle (Control): Pins G, RX, TX are used for
controlling, configuring and managing this device,

6
No.
Name
Description
encoders and decoders through RS232 software
or a third-party controller.
RS232 Parameters
Baud Rate
9 600 bps
Data Bits
8 bits
Parity
None
Stop Bits
1
Right (Power): Pins G, 12V are used for
providing a 12VDC 0.5A output.
Note: Please connect the correct pins for device
debug and control. When this device is powered
by a power adapter, if you connect control
terminal to control port after first connection with
the debug port, you need to reboot this device for
device control process.
3
DC 12V
Connects to a supplied 12 VDC 1 A power
adapter.

7
Installation
Note: Before installation, ensure the device is disconnected
from the power source.
Steps to install the device in a suitable location:
1. Remove the four screws from the two side panels.
2. Position and install the mounting brackets on the two side
panels using the mounting screws provided in package.
3. Mount and secure the device to a surface or a suitable
location with the mounting screws (provided by others).

www.avpixelfly.com
Rev 200622