PL Systems Insect-O-Cutor IND35 User manual

IND35
Please read these instructions carefully and store in a safe place
for future reference.
IND35
As part of the Insect-O-Cutor®brand of insect control products,
IND35 is an easy to service and highly effective flykiller which
utilises highly effective Synergetic®UV tubes and is designed for
use with a high specification glupac®glueboard. Constructed
from coated mild steel, IND35 can be wall or desk mounted .
CONTENTS OF PACKAGE
- 1 x IND35 flykiller
- 2 x 15W 18” Shatterproof Synergetic UV tubes
- 1 x glupac®pheromone impregnated glueboard (Fitted)
- 3 x screws and wall plugs
- 1 x Mains cable (Type X)
WARNING - THIS APPLIANCE MUST BE EARTHED
INSECT CONTROL PRODUCTS
IND35 utilises high powered Synergetic®tubes to attract flying
insects and retains the caught insects on a glueboard for
inspection or hygienic disposal. Synergetic® tubes combine both
ultraviolet light and visible green light to attract a wider range of
flying insects.
WARNING
IND35 is not to be used by children or persons with reduced
physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or
instruction.
Children should be supervised to ensure they do not play with
the appliance.
If the mains cable is damaged it must be replaced by a
specialist mains cable available from P+L Systems Ltd or your
supplier.
This appliance is not suitable for barns, stables, or similar
locations.
POSITIONING AND GUIDANCE FOR USING IND35
THIS UNIT IS FOR INDOOR USE ONLY.
IND35 should ideally be fixed around two meters above the
ground, preferably in the darkest place within the area to be
protected. Do not position the unit close to windows, skylights or
other sources of light, or where it may be obscured by furniture,
doors or other obstacles. Ideally, IND35 should be visible from
every part of the area to be protected.
IND35 should ideally be in operation for 24 hours a day, ensuring
your premises are kept free of flying insects. Insects are most
attracted to IND35 at night when there is no competition from
daylight or other light sources.
GUARANTEE
IND35 has a five year guarantee and if maintained as
recommended in these instructions, should continue to work for
many years.* Use of non-approved consumables may invalidate
the guarantee. Ensure genuine glupac®glueboards are used in
conjunction with this product.
INSTALLATION
INSTALLATION SHOULD BE CARRIED OUT BY SERVICE
PERSONNEL ONLY.
IND35 has a swing open front, which allows simple and quick
access to the inside of the flykiller for installation and
servicing.
Install IND35 by offering the product up to the wall and
marking the three fixing centers. Then drill holes and fit the
supplied wall plugs and screws. (For specialist wall surfaces
such as plasterboard, appropriate wall plugs should be used.)
Then hang the product onto the mounting screws.
Once IND35 is installed in position, fit the glupac® glueboard in
place as described in the glueboard replacement section of
this document. Use the removable mains lead and plug to
connect IND35 to an appropriate rating, as specified on the
specification label found on the top of the product.
CLEANING
CLEANING SHOULD BE CARRIED OUT BY SERVICE PERSONNEL
ONLY, AFTER ENSURING THAT THE UNIT IS DISCONNECTED
FROM THE MAINS SUPPLY.
It is recommended that cleaning is carried out regularly when
the glueboard is replaced. Once the glueboard is removed,
the unit should be thoroughly wiped down with a damp
cloth, removing any build up of dirt. Ensure the unit is
completely dry before reconnecting it to the power supply.
Professional Glueboard Insect Control
*Excludes tubes, glueboards and starters. Does not cover breakdown due to misuse, incorrect
operation or use in an incorrect application.
IND35

R2 05/03
SPECIFICATION / REPLACEMENT PARTS
GLUEBOARD REPLACEMENT
BEFORE REPLACING THE GLUEBOARD, ALWAYS ENSURE THAT THE UNIT IS DISCONNECTED FROM THE
MAINS SUPPLY.
The glueboard should be replaced every month with a genuine glupac® glueboard. Use of
non-approved glueboards may invalidate your guarantee. IND35 comes supplied with discreet
black glueboards with printed grids for simple insect evaluation and monitoring.
To replace the glueboard…
1. Swing the front guard open.
2. Remove the protective release paper from the new glupac® glueboard.
3. Position the top of the glupac® glueboard in position behind the two locating pins,
then carefully drop the horizontal face of the board into position.
Always ensure the selected genuine glupac® glueboards are compatible with your unit,
available from your pest control operator or P+L Systems Ltd.
TUBE REPLACEMENT
TUBE REPLACEMENT SHOULD BE CARRIED OUT BY SERVICE PERSONNEL ONLY, AFTER ENSURING THAT
THE UNIT IS DISCONNECTED FROM THE MAINS SUPPLY.
To ensure the efficiency of IND35 in catching flying insects, the Synergetic® tubes should be
replaced annually. After twelve months the phosphor coating that emits the correct wavelength
of UV light has burnt away and the UV output is diminished substantially.
To replace the UV tubes…
1. Swing the front guard open.
2. Gently rotate the tube through 90º.
3. Pull the tube forward until it becomes free from the tube holder.
4. Reverse the process with the new Synergetic® tube.
5. Dispose of the used UV tubes in conjunction with local regulations.
STARTER REPLACEMENT
STARTER REPLACEMENT SHOULD BE CARRIED OUT BY SERVICE PERSONNEL ONLY, AFTER ENSURING
THAT THE UNIT IS DISCONNECTED FROM THE MAINS SUPPLY.
The starters provides an extra spark to initially light the UV tubes. Starters wear out and should be
replaced at the same intervals as the UV tubes.
To replace the starters…
1. Swing the front guard open.
2. Rotate the starter anti-clockwise.
3. Pull the starter free from the unit.
4. Reverse the process with the replacement starter.
Unit IND35
Voltage 230V ~ 50Hz
Dimensions(mm) 470 x 230 x 130
Coverage 80 Sq. Meters
Weight 5.0Kg
Light Output 30W
Tubes 2 x TGX15-18S
Starter 2 x I154
Glueboards (x6) INF212 (Black)
Starter Replacement Glueboard Replacement
1
2
P+L Systems
Sterling House
Grimbald Crag Close
Knaresborough
North Yorkshire
HG5 8PJ
UK
T [phone]
F [phone]
W www.pandlsystems.com
E [email protected]
WEEE Compliance No. 01576542
C2013
P+L Systems Ltd
Information provided on these instructions is modified and
updated from time to time. This is due to the constant
redevelopment of our products. As such, it is not intended that
you should rely on it or that it should form part of any contract.
Tube Replacement