EC10B User’s Manual - page 8
CONTENTS
EC10B User’s Manual - Contents
U S E R ’ S M A N U A L
EC10B User’s Manual - page 2
Installation
System #1: 2 channel input/2-way system withlow level inputs
EC10B User’s Manual - page 1
EC10B User’s Manual - page 6
Input, output, remote and power connections
EC10B User’s Manual - page 3
Front and rear channel controls
EC10B User’s Manual - page 4
EC10B User’s Manual - page 5
Electrical and remote level controller connections
Inputand output connections
System #2: 2 channel input/2-way system with high level inputs
EC10B User’s Manual - page 7
Specifications
EC10B User’s Manual - page 9
Before installing your new Planet Audio
crossover, please become familiar with
all the information contained in this
manual.
Choose a mounting location where the
unit will not distract or otherwise
interfere with the driver’s ability to
control the vehicle.
Use only the installation parts and
hardware provided with the unit to
ensure proper installation. Usingother
parts can cause malfunction and
possible damage to your Planet Audio
crossover.
Avoid installing the unit in a location
which is subject to high temperatures,
direct sunlight, hot air from such
sources as heaters or exhaust lines,
or where it will be subject to contact
with dust, dirt, moisture or excessive
vibration.
This crossover accepts the input signal
from a 2-channel input source, using
either low level RCA outputs or high
level (speaker) outputs from your head
unit.
Input source selection
The EC10B features both low level (RCA)
inputs and high level (speaker level) inputs,
enabling you to generate a two-way sys-
tem from virtually any head unit you may
own.
If your headunit has RCA Left and Right
Channel outputs, you should choose these
for your EC10B input source, since the
quality of sound reproduction is best when
using these.
However, if your head unit lacks RCA
outputs, you can use the speaker outputs
from the head unit as an input source for
the EC10B. Simply follow the wiring dia-
grams in this manual closely to make sure
you get the best performance possible
and avoid damaging your head unit.
Input and output connections vary depending on the system application. Examples
are shown in system diagrams on the pages whichfollow in this manual. Always use
high quality RCA cables for low level input and output connections.
EC10B output: 2-way stereo system: Tweeter/Mids L/Rchannel
Subwoofer L/R* channels
* can also be set to Mono Sub channel
To L/R output
from head unit
MONOBLOCK
SUBWOOFER AMPLIFIER
FOR
RIGHT CHANNEL
MONOBLOCK
SUBWOOFER AMPLIFIER
FOR LEFT CHANNEL
Turning on the power
Before powering up for the first time:
1. Carefully check all electrical and
audio connections.
2. Set all level controls to their minimum
positions.
3. Set all switches to the settings
appropriate for your installation.
The EC10B has internal ON/OFF
circuitry which responds to turning ON
or OFF the head unit of your car audio
system. This requires that yourhead
unit have a remote turn-on lead
available on the rear panel (which most
head units have).
With this convenient remote turn-on/off
feature, you never have to worry about
turning off the power to the equalizer
when you shut off the audio system.
When you are confident all connections
have been made correctly:
1. Power up your audio system by
turning on the head unit.
2. Set the volume control on the head
unit to about 3/4 volume, and adjust
the EC10B’s Speaker Input Gain
controls for each channel to just below
the level of distortion.
Further fine tuning of the controls on
the EC10B andthe input levels of the
connected amplifiers may be
necessary to obtain satisfactory results.
If you are unsure about howto fine-
tune the system, please consult with
your Planet Audio dealer.
MIDS/HIGHS
2 CHANNEL AMPLIFIER
EC10B output: 2-way stereo system: Tweeter/Mids L/R channel
Subwoofer L/R* channels
* can also be set to Mono Sub channel
To L/R speaker outputs
from head unit MONOBLOCK
SUBWOOFER AMPLIFIER
FOR
RIGHT CHANNEL
MONOBLOCK
SUBWOOFER AMPLIFIER
FOR LEFT CHANNEL
MIDS/HIGHS
2 CHANNEL AMPLIFIER
Grey/Black
R(+)
Grey R(-)
White/Black
L(+)
White L(-)
Mounting the crossover
The EC10B is designed to be installed
securely to a flat surface in your
vehicle using the screws and washers
provided. Install the unit according to
the diagram below.
1How this crossover is used
1Input source selection
2Installation
2Mounting the equalizer
2Turning on the power
3Input, output, remote and
power connections
4Front and rear channel
controls
5Electrical and remote level
controller connections
6System diagrams
8Troubleshooting
9Specifications
Congratulations on your
purchase of a Planet Audio
Crossover.
It has been designed, engineered
and manufactured to bring you
the highest level of performance
and quality, and will afford you
years of listening pleasure.
Thank you for making
Planet Audio your choice for car
audio entertainment!
page
LOW PASS: 35-400Hz
HIGH PASS: 50-1.5kHz
12dB/octave
0-+12dB
110dB
0.01%
80dB
20k Ohms (low level); 470 ohms (high level)
100 Ohms
1:2 (+6dB)
DC-to-DC switching type
8V maximum
4-1/4” x 7-1/14” x 1-1/8”
(108 x 184 x 29mm)
Crossover center frequency ranges
Crossover slope
Bass Boost level adjustment
Signal-to-Noise Ratio
THD
Channel separation
Input impedance
Output impedance
Output gain
Power supply
Output voltage
Dimensions (W x D x H)
All specifications subject to change without notice.
Low Pass (Subwoofer) Crossover
Channel Controls:
High Pass (Highs/Mids) Crossover
Channel Controls:
Input Controls:
Self-tapping
screw
Spring washer
Flat washer
TWEETERS,
MIDRANGE,
MIDBASS
or
FULL RANGE
SPEAKERS
SUBWOOFER
SUBWOOFER
Right
Left
SUBWOOFER
SUBWOOFER
Right
Left
TWEETERS,
MIDRANGE,
MIDBASS
or
FULL RANGE
SPEAKERS
