Planet ATA-150 Series User manual

VoIP Analog Telephone Adapter
ATA-150/ATA-150S
User’s manual
Version 1.0.2
- 1 -

Copyright
Copyright (C) 2009 PLANET Technology Corp. All rights reserved.
The products and programs described in this User’s Manual are licensed products of PLANET Technology, This
User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all
accompanying hardware, software, and documentation are copyrighted.
No part of this User’s Manual may be copied, photocopied, reproduced, translated, or reduced to any electronic
medium or machine-readable form by any means by electronic or mechanical. Including photocopying, recording,
or information storage and retrieval systems, for any purpose other than the purchaser's personal use, and without
the prior express written permission of PLANET Technology.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications,
and makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment on the
part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s
Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and
reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s
Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your
comments and suggestions.
CE mark Warning
The is a class B device, In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.
Trademarks
The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hardware
and software products by their trade names. In most, if not all cases, their respective companies claim these
designations as trademarks or registered trademarks.
- 2 -

- 3 -
Revision
User’s Manual for PLANET VoIP Analog Telephone Adapter:
Model: ATA
Rev: 1.0.2 (2009, July)
Part No. EM-ATA150 Series

- 4 -
TABLE OF CONTENTS
Chapter 1...................................................................................................................................6
Introduction ..............................................................................................................................6
Overview.......................................................................................................................................................6
Package Content ..........................................................................................................................................7
Physical Details ............................................................................................................................................7
Physical Interface & Button.................................................................................................................8
Chapter 2 Preparations & Installation.................................................................................10
Physical Installation Requirement............................................................................................................10
Keypad commands .............................................................................................................................11
Chapter 3 TCP/IP Settings.....................................................................................................14
Configuring and monitoring yourATA from web browser....................................................................14
Overview on the web interface of ATA ..............................................................................................14
Manipulation of ATA via web browser...............................................................................................14
LAN IP address configuration via web configuration interface .........................................................15
Chapter 4 VoIP Settings.........................................................................................................21
Phone 1 / Phone 2 (ATA-150S) ..........................................................................................................21
Tone....................................................................................................................................................30
Other...................................................................................................................................................32
Auto Config........................................................................................................................................33
Chapter 5 Management .........................................................................................................35
Status..................................................................................................................................................35
Statistics .............................................................................................................................................35
DDNS.................................................................................................................................................36
Time Zone Setting..............................................................................................................................37
Denial-of-Service ...............................................................................................................................38
Log .....................................................................................................................................................39
Upgrade Firmware..............................................................................................................................39
Save / Reload Settings........................................................................................................................40
Password Setup ..................................................................................................................................40
Reboot................................................................................................................................................41
Logout................................................................................................................................................41
AppendixAVoice communication samples..............................................................................................42
Peer to peer (P2P) mode.....................................................................................................................42
Case 2: (Peer-to-Peer mode) ATA-150S Port 1 to Port 2 communications.........................................42
Case 3: SIP Proxy mode.....................................................................................................................43
Case 4: Call Forward Feature_Example 1..........................................................................................44
Case 5: Call Forward Feature_Example 2..........................................................................................46
Appendix B The method of operation guide............................................................................................47

- 5 -
Call Transfer.......................................................................................................................................47
3-Way Conference..............................................................................................................................47
Call Waiting........................................................................................................................................47
Switch the Default Proxy ...................................................................................................................48
Auto Update firmware by manual (Keypad)......................................................................................48
Appendix C Frequently Asked Questions List ........................................................................................49
Appendix D ATA Specifications................................................................................................................50

11
Chapter 1
Introduction
Overview
Based on years of VoIP manufacturing experiences, PLANET Technology VoIP total solutions are
known for advanced implementation of standards based telephony with mass deployment capability.
Cost-effective, easy-to-install and simple-to-use, the PLANETATA-150/ATA-150S VoIP Phone Adapter
(“ATA” in the following term) converts standard telephones to IP-based networks. The service providers
and enterprises can offer users traditional and enhanced the telephony communication services via the
existing broadband connection to the Internet or corporation network.
With the ATA, home users and companies are able to save the installation cost and extend their past
investments in telephones, conference and speakerphones. The ATA equipped with two telephony
interfaces, users may register to different SIP proxy servers, IP PBX and establish up to 2 concurrent
VoIP calls for more flexibility in the voice communications. ATA can be the bridge between the
traditional analog telephones to IP network with an extremely affordable investment.
Product Features
•Feature-rich telephone service over home Internet / Intranet connection
•Up to 2 concurrent VoIP calls
•Cost-effective, easy-to-use solution for Analog Telephone Adapter
•Web-based utility and machine configuration
•Remote administrator authentication
•Voice prompt for machine configurations
VoIP Features
•SIP 2.0 (RFC3261) compliant
•Voice codec: G.711(A-law /μ-law),G.729 AB, G.723 (6.3 Kbps / 5.3Kbps)
•FoIP : T.38 FAX Relay, G.711 Fax pass-through
•QoS : IP TOS (IP Precedence) / DiffServ
•Call Waiting / Hold / Resume / Transfer / Forward /
•3-Way Conference / Caller ID Generation
•VAD / CNG / Dynamic Jitter Buffer
•SNMP v1/v2, TR-069 and Auto Provision
- 6 -

Package Content
The contents of your product should contain the following items:
VoIP Telephone Adapter
Power adapter
Quick Installation Guide
User’s Manual CD
RJ-11 cable x 1
Physical Details
The following figure illustrates the each panel of SIP ATA.
ATA-150: SIP Analog Telephone Adapter (1 x RJ-45, 1 x RJ-11)
ATA-150S: 2-Port FXS SIP Analog Telephone Adapter (1 x RJ-45, 2 x RJ-11)
Front Panel of ATA-150
Left / Right Panel of ATA-150
- 7 -

Front Panel of ATA-150S
Left / Right Panel of ATA-150S
Physical Interface & Button
1 RESET
Pressing 1 second to reboot machine.
Pressing 5 seconds to reset to the factory default setting
2 12V DC 12V DC Power input outlet
3 LAN RJ-45 connector, for Internet access, connected directly to
Switch/Hub through straight CAT-5 cable.
4 Phone RJ-11 connector, connected directly to the analog phone.
- 8 -

LED Display of ATA-150
PWR Power is supplied to the device.
LNK/ACT OFF: the device is disconnected to LAN.
ON: the device is connected to LAN.
Phone
OFF: the phone is idle.
ON: the phone is in use (off-hook).
Blinking: the phone is ringing.
LED Display of ATA-150S
PWR Power is supplied to the device.
LNK/ACT OFF: the device is disconnected to LAN.
ON: the device is connected to LAN.
RING1
OFF: the phone is idle.
ON: the phone is in use (off-hook).
Blinking: the phone is ringing.
RING2
OFF: the phone is idle.
ON: the phone is in use (off-hook).
Blinking: the phone is ringing.
1. The default IP is http://192.168.0.1. Press RESET button
on rear panel over 5 seconds will reset the VoIP Phone
A
dapter to factory default value. (Except speed dial and
call forward settings)
2. Using the power supply that is not the one included in
package may cause device damage and void the warranty
for this product.
3. Switching type AC Adapter is required for normal
operating, use of Linear type AC adapter may cause device
malfunciton.
Í Note
- 9 -

2
Chapter 2
Preparations & Installation
Physical Installation Requirement
This chapter illustrates basic installation of ATA analog Phone Adapter (“ATA” in the following term)
•Network cables. Use standard 10/100Base-TX network (UTP) cables with RJ-45 connectors.
•TCP/IP protocol must be installed on all PCs.
For Internet Access, an Internet Access account with an ISP, and either of a DSL or Cable modem
Administration Interface
PLANET ATA provides GUI (Web based, Graphical User Interface) and utility for machine management
and administration.
Utility quickly search access
Using for soft utility to search SIP ATA from current network. The utility not only easy-to-use and
provides user more convenience for configuration access, at the some time If you forget this IP address
can also found that via the utility.
Copy this utility tool in your laptop or desktop computer first. And, this utility tool can only be executed in
Windows series of operating systems.
Click the icon for windows desktop to start searching ATA in the network.
Select “Refresh” and you will get the results as above choose the device you want to configuration,
click this IP address of ATA and press the “Connect to Device” button to browse the web page.
- 10 -

Web configuration access
You will connect to SIP ATA via your web browser automatically. ATA will prompt for logon username /
password, please enter: admin / 123 to continue machine administration.
ATA will prompt for logon username/password, please enter: admin / 123 to continue machine
administration.
The default IP address of ATA is 192.168.0.1. You also could open your web browser, and insert
http://192.168.0.1 in the address bar of your web browser to logon ATA web configuration page.
To start ATA web configuration, you must have one of these web browsers installed on computer for
management
• Microsoft Internet Explorer 6.00 or higher with Java support
Please locate your PC in the same network segment
(192.168.0.x) of ATA. If you’re not familiar with TCP/IP,
please refer to related chapter on user’s manual CD or
consult your network administrator for proper network
configurations.
Í Note
Keypad commands
The ATA series phone adapters support telephone keypad configurations, please connect analog
telephone set and refer to the following table for machine network configurations.
IVR Menu Choice Machine operation Parameter(s) Notes
#111#
Set DHCP client None ATA will change to DHCP
Client
#112xxx*xxx*xxx*
xxx#
Setup Static IPAddress
Use the * (star) key
when entering a decimal
point.
DHCP will be disabled and
system will change to the
Static IP type.
- 11 -

- 12 -
#113xxx*xxx*xxx*
xxx#
Set Network Mask
Use the * (star) key
when entering a decimal
point.
Must set Static IP first.
#114xxx*xxx*xxx*
xxx#
Set Gateway IP Address
Use the * (star) key
when entering a decimal
point.
Must set Static IP first.
#115xxx*xxx*xxx*
xxx#
Set Primary DNS Server
Use the * (star) key
when entering a decimal
point.
Must set Static IP first.
#190#
Unlock None
Must unlock the protect
function before carry out
the firmware update
(#160#).
#195#
Save Network Settings None
Must save network
settings after set up
network settings via
keypad.
#198#
Factory Reset None
The system will be reset to
factory default value and
reboot automatically.
Following keypad commands can be used to display the network settings enabled on ATA via voice
prompt.
IVR Menu Choice Machine operation Notes
#120#
Check IPAddress IVR will announce the current IP address of
the ATA.
#121#
Check network connection Type IVR will announce if DHCP in enabled or
disabled.
#122#
Check the Phone Number IVR will announce current enabled VoIP
number.
#123#
Check Network Mask IVR will announce the current network mask
of the ATA.
#124#
Check Gateway IP Address IVR will announce the current gateway IP
address of the ATA.
#125#
Check DNS Server Setting IVR will announce the current setting in the
DNS field.
#128#
Check Firmware Version IVR will announce the version of the
firmware running on the ATA.

- 13 -
Following keypad commands can be used to set up the main function .
IVR Menu Choice Machine operation Parameter(s) Notes
#130+first
priority codec
Set First Priority Codec
01: G.711 u-Law, 02:
G.711 a-Law, 03: G.729,
04: G.723 6.3K, 05:
G.723 5.3K, 06: G.726
16K, 07: G.726 24K, 08:
G.726 32K, 09: G.726
40K, 10: GSM-FR
You can set the codec you
want to the first priority.
For example: #13001#
Set G.711 u-Law to the first
priority codec
#133#
Set Speaker Voice Gain 00~31, 32: Mute For example: #13305#
Mic Voice: 5
#134#
Set Mic Voice Gain 00~31, 32: Mute For example: #13410#
Mic Voice: 10
#138#
Enable call waiting None Enable Call waiting
#139#
Disable call waiting None Disable Call waiting
#140+Forward
type+Forward
Phone Number#
Forward Settings
Forward Type:
1: Immediate Forward
2: Busy Forward
3: No answer Forward
For example: #1401101#
Immediate Forward to 101
#141#
Disable Forward Settings None
#150#
Select Default Realm 0: Realm 1, 1: Realm 2 For example: #1501#
Set Default Proxy to Realm 2
#160#
Update firmware None
Update firmware
Must unlock the protect
function (#190#) before carry
out the firmware update.

3
Chapter 3
TCP/IP Settings
Configuring and monitoring your ATA from web browser
The ATA integrates a web-based graphical user interface that can cover most configurations and
machine status monitoring. Via standard web browser, you can configure and check machine status
from anywhere around the world.
Overview on the web interface of ATA
With web graphical user interface, you may have:
More comprehensive setting feels than traditional command line interface.
Provides user input data fields, check boxes, and for changing machine configuration settings
Displays machine running configuration
To start ATA web configuration, you must have one of these web browsers installed on computer for
management
Microsoft Internet Explorer 6.00 or higher with Java support
Manipulation of ATA via web browser
Log on ATA via web browser
After TCP/IP configurations on your PC, you may now open your web browser, and input
http://192.168.0.1 to logon Phone Adapter web configuration page.
Enter the IP address of the ATA which
by default is 192.168.0.1
Phone Adapter will prompt for logon username/password: admin / 123
ATA login prompt screen
- 14 -

When users login the web page, users can see the Phone Adapter system information like firmware
version, company…etc in this main page.
VoIP Phone Adatper main page
LAN IP address configuration via web configuration interface
This page is used to configure the parameters for Internet network which connects to the LAN port of
your ATA. Here you may change the access method to static IP, DHCP, PPPoE or PPTP by click the
item value of LAN Access type.
- 15 -

Connection Type Description – Static IP
Static IP Set LAN interface as Static IP mode.
LAN IPAddress of the ATA
IP Address
Default : 192.168.0.1
LAN mask of theATA
Subnet Mask
Default : 255.255.255.0
Gateway of the ATA
Default Gateway
Default : 192.168.0.254
Set MTU (maximum transmission unit) size
MTU Size
Default : 1412
Set three alternative Domain Name Server for LAN interface.
DNS1/ 2/ 3
Default : Null
To clone the MAC by manual input.
Clone MAC Address
Default : 000000000000 (Null)
Check to enable UPnP function
Enable uPnP
Default : Disable
Check to enable IPsec function
Enable IPsec pass through on
VPN connection Default : Enable
Check to enable PPTP pass through function
Enable PPTP pass through on
VPN connection Default : Enable
Check to enable L2TP pass through function
Enable L2TP pass through on
VPN connection Default : Enable
- 16 -

Connection Type Description – DHCP Client
DHCP Client Set LAN interface as DHCP mode.
Select to attain DNS automatically from server or user wants to
set DNS manually.
Attain DNS Automatically
/
Set DNS Manually
Default : Set DNS Manually
- 17 -

Connection Type Description – PPPoE
PPPoE Set LAN interface as PPPoE mode.
Set user name of PPPoE connection
User Name
Default : Null
Set password of PPPoE connection
Password
Default : Null
Set Service Name of PPPoE for description
Service Name
Default : Null
Set PPPoE connection type to be Continuous/ Connect on
Demand/ Manual. If user set type as Continuous, ATA will keep
trying to connect to server when PPPoE disconnect. If user set
type as Connect on Demand, please set following idle time, ATA
will check connection after this time. If user set type as Manual,
ATA will only connect or disconnect by press Connect or
Disconnect manually.
Connection Type
Default : Continuous
- 18 -

Set PPPoE connection idle time for Connect on Demand.
Idle Time
Default : 5
Set IP type if Dynamic IP or Static IP at PPPoE connection.
LAN Physical
Default : Dynamic IP
LAN IPAddress of the ATA at Static IP type.
IP Address
Default : 0.0.0.0
LAN Mask of theATA at Static IP type.
Subnet Mask
Default : 0.0.0.0
After confirming the modification you’ve done, please click on the SUBMIT button to apply settings
effective and the ATA will be reload page automatic by itsely, that you must to afresh enter the final
modification IP address for logon web management.
Connection Type Description – PPTP
- 19 -

PPTP Set LAN interface as PPTP mode.
Set IP type if Dynamic IP or Static IP at PPTP connection.
Mode
Default : Dynamic IP
LAN IPAddress of the ATA at Static IP type.
IP Address
Default : 0.0.0.0
LAN Mask of theATA at Static IP type.
Subnet Mask
Default : 0.0.0.0
Gateway of the ATA
Gateway
Default : 0.0.0.0
Set PPTP Server IP address.
Server IP Address
Default : 0.0.0.0
Set user name of PPTP connection
User Name
Default : Null
Set password of PPTP connection
Password
Default : Null
Í Note
Please be noticed that the Utility Tool is only designed
for the LAN environment setting. If the “Connect Type” is
“PPPoE”, the Utility Tool can NOT find the device.
- 20 -