Planet HDP-1100PT User manual

720p SIP Door Phone with PoE
HDP-1100PT

720p SIP Door Phone with PoE
HDP-1100PT
2
Copyright
Copyright ©2015 by PLANET Technology Corp. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written
permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect
to the contents hereof and specifically disclaims any warranties, merchantability or fitness for
any particular purpose. Any software described in this manual is sold or licensed "as is".
Should the programs prove defective following their purchase, the buyer (and not PLANET,
its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and
any incidental or consequential damages resulting from any defect in the software. Further,
PLANET reserves the right to revise this publication and to make changes from time to time
in the contents hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered
trademarks of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance, use only shielded interface cables when connecting to
computer or peripheral devices.Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency
exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches)
during normal operation.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity
when working with electrical equipment. All guidelines of this and of the computer
manufacture must therefore be allowed at all times to ensure the safe use of the equipment.

720p SIP Door Phone with PoE
HDP-1100PT
3
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
WEEE Regulation
To avoid the potential effects on the environment and human health as a result of
the presence of hazardous substances in electrical and electronic equipment, end
users of electrical and electronic equipment should understand the meaning of
the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted
municipal waste and have to collect such WEEE separately.
Revision
User’s Manual of 720p SIP Door Phone with PoE
Model: HDP-1100PT
Rev: 1.00 (August, 2015)
Part No. EM-HDP-1100PT_v1.0

720p SIP Door Phone with PoE
HDP-1100PT
4
Table of Contents
Chapter 1.Product Introduction......................................................................5
1.1Package Contents..............................................................................5
1.2Overview ............................................................................................5
1.3 Specifications......................................................................................5
Chapter 2.Hardware Interface........................................................................7
2.1 Physical Descriptions..........................................................................7
2.2 Hardware Installation..........................................................................9
2.3 Initial Utility Installation........................................................................9
Chapter 3.Web-based Management............................................................12
3.1 Introduction.......................................................................................12
3.2 Status................................................................................................12
3.2.1 Device Info..............................................................................12
3.2.2 Service Status.........................................................................13
3.3 Service..............................................................................................13
3.3.1 SIP..........................................................................................14
3.3.2 Calls........................................................................................15
3.3.3 Video ......................................................................................16
3.3.4 RTSP Server...........................................................................17
3.3.5 Web Server.............................................................................17
3.4 Device...............................................................................................18
3.4.1 Volume Control.......................................................................18
3.4.2 Camera...................................................................................19
3.4.3 Relay ......................................................................................19
3.5 System..............................................................................................19
3.5.1 Network ..................................................................................20
3.5.2 Date &Time.............................................................................21
3.5.3 Maintenance...........................................................................21
3.5.4 Reset......................................................................................22
3.5.5 Reboot....................................................................................23
Appendix A:Door Phone SIP Configuration .................................................24
Appendix B:Control HDP-1100PT by Smart Phone .....................................25
Appendix C:Open Door by VoIP Phone .......................................................31
Appendix D:Troubleshooting & Frequently Asked Questions.......................36

720p SIP Door Phone with PoE
HDP-1100PT
5
Chapter 1. Product Introduction
1.1 Package Contents
The package should contain the following:
zQuick Installation Guide x 1
zPlastic Wall Mount x 1
zMetal Wall Mount x 1
zScrew Kit x 1
If any of the above items are missing, please contact your seller immediately.
1.2 Overview
Keyless Control and Convenience
PLANET HDP-1100PT is an SIP Door Phone with PoE feature. It supports H.264/MJPEG
compression formats and delivers excellent picture quality in 720p HD resolutions at 20 frames
per second (fps). The door phone has night vision that you can see short distances in low light.
It provides the flexibility and control required for high-quality property complex visitor
management, property protection, intercom, and message service.
Real-time Monitoring
IP cameras can be linked to PLANET HAC-1000 and Cloud Home app for remote monitoring.
Users can keep an eye on their home on mobile phones over a secure connection to the Home
Automation Control Gateway.
Easy Communication via Intercom
The two-way intercom function provided by the HDP-1100PT allows you to see the visitors and
also communicate with them. The HDP-1100PT includes inputs/outputs for connecting to
external devices such as door lock or door sensors. When the visitors press the call button at
your door, you can press the unlock button on your mobile phone or PLANET HTS-1000P
touch screen control pad to open the door for your visitors.
AEC (Acoustic Echo Cancellation)
Acoustic Echo Cancellation (AEC) technology is adopted in PLANET’s HDP-1100PT Door
Phone and HTS-1000P touch screen control pad to enable users to minimize the voice sound
signal distortion shown in the diagram below, thus guaranteeing the best-in-class sound
quality.
Finding the Door Phone via Smart Discovery
PLANET Smart Discovery is a simple, freely available application for locating intercoms from
the IP family in the network. After searching the network, the application shows the device
name, firmware version and IP address of all intercoms found on a chart. This simplifies the
administration and installation of intercom systems. Simply run the easy-to-use software to get
immediate results.
1.3 Specifications
Product HDP-1100PT
Camera
Image Device 1/4" 1 mega-pixel progressive scan CMOS sensor
View Angle 112.4-degree wide-ranging horizontal view angle
Monitoring Range 3 meters

720p SIP Door Phone with PoE
HDP-1100PT
6
LED White LED x 6, effective up to 0.6 meters
Video
Video Compression H.264 / M-JPEG
Video Resolution H.264: 720p / 640 x 480 / 320 x 240
MJPEG: 720p / 640 x 480 / 320 x 240
Frame Rate Up to 20fps for all resolutions
Audio
Audio Streaming Two-way audio
Audio Compression RTSP: G.711,AAC
Microphone Built-in microphone and speaker input
Audio Output Acoustic Echo Cancellation
Network and Configuration
Network Standard IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
Protocol SIP 2.0 (RFC-3261), IPv4, TCP/IP, HTTP, DDNS, DHCP, RTSP,
DNS, PPPoE
Functions Intercom, Doorbell Control, Manual Alarm, Monitoring
General
Power Requirements IEEE 802.3af Class 3
Operating Temperature -10 ~ 45 degrees C
Operating Humidity 0 ~ 90% (non-condensing)
Weight 290g
Dimensions (W x D x H) 114 x 114 x 35 mm
Installation Wall-mount type
Emission CE, FCC
Connectors
10/100 Mbps Ethernet, RJ45
Call Button
Relay Output Port (control door lock or alarm)
DI Port (for door sensor, PIR, emergency button)

720p SIP Door Phone with PoE
HDP-1100PT
7
Chapter 2. Hardware Interface
2.1 Physical Descriptions
Dimensions (W x D x H) 114 x 35 x 114 mm
Weight 290g (gross weight)
Real Panel
Microphone
CMOS Sensor White LED
Speaker Call Button
Interface Description
CMOS sensor The HDP-1100PT door phone has a built-in IP camera supporting a
high-resolution video of up to 1280 x 720 pixels.
White LED Emits white light to provide light source in dark places.
Call button Press the “Call” button to check who the caller is before opening the
doors, or talk to him/her.
Microphone The door phone has a built-in microphone hidden in the pinhole
located on the front panel.
Speaker The door phone has a built-in speaker for convenient communication
and alert use.

720p SIP Door Phone with PoE
HDP-1100PT
8
I/O Control Instruction
Green: NO
Brown: COM
Blue: NC
Orange: DI
Yellow: DI
Black: GND
Red: +DC12V
Electric deadbolt for
door entry system
Connect to
RJ45 cable
Interface Description
DC Power (red) The input power is 12V DC, 1A
DI
(orange and yellow)DI connects to the sensor for notifying the status, so that the CPU
can do the appropriate action.
DO
(green, brown and
blue)
DO connect to control device and the status of device can be
accessed (NC-COM) or (NO-COM).
The PCB controls the power On/Off status of device via power relay.
Example
Anode lock x 1 and the list below is I/O interface.
Red 12VDC+
Black GND
Yellow Button connect – line
Blue COM
White NO
Gray NC
Step 1. Connect the COM of HTP-1100PT and GND of anode lock
together.

720p SIP Door Phone with PoE
HDP-1100PT
9
Step 2. Connect the NC of HDP-1100PT and Button of anode lock
together.
Step 3. Provide the power to anode lock and HDP-1100PT. When the
anode lock is powered by 12VDC, the anode lock would switch to
lock location.
Step 4. Press the Open door button to open door by mobile phone.
2.2 Hardware Installation
Step 1:Surface-mount the HDP-1100PT SIP IP video door phone in a desired location.
Step 2: Put the Ethernet cable through the square hole, measuring 35 x 35mm.
Panel
Step 3: Fix the door phone on the wall using a roof or a panel and two screws as shown below:
Step 4: Connect the HDP-1100PT to IEEE802.3af/at POE switch or router via RJ45 cable.
2.3 Initial Utility Installation
This chapter shows how to use utility to find the IP of your door phone. The door phone is with
the default settings. However, to help you find the networked door phone quickly, the windows
utility PLANET Smart Discovery can search door phone in the network that can help you to
configure some basic settings before you start advanced management.
Step 1: Please download the search tool from Planet download center:

720p SIP Door Phone with PoE
HDP-1100PT
10
Step 2: Unzip the file and run the program “ SmartDiscoveryLite”.
Step 3: The window below will show the network information of control gateway.
Before searching the IP, please make sure your PC is in the same IP segment as door
phone.
Step 4: The information in the red box can be modified. Then click “Update Device”.

720p SIP Door Phone with PoE
HDP-1100PT
11
Step 5: Enter the password: admin. After clicking
“OK”, the information will be changed.

720p SIP Door Phone with PoE
HDP-1100PT
12
Chapter 3. Web-based Management
Your door phone is ready to put you in control of your home. Please take a few minutes to read
through this guide to familiarize yourself with the steps required to set up your door phone.
This chapter provides setup details of the door phone Web-based Interface.
3.1 Introduction
Door phone can be configured with your Web browser. Before configuring, please make sure
your PC is in the same IP segment as door phone.
Enter the user name and password (admin/admin) to access interface.
3.2 Status
Here you can view the status of the door phone.
3.2.1 Device Info
Parameters Description
Product Name Model name of the door phone.

720p SIP Door Phone with PoE
HDP-1100PT
13
Hardware Version The current hardware version of the door phone.
Firmware Version The current firmware version of the door phone.
Uptime The operating time from boot time till now.
3.2.2 Service Status
This section provides the information of network status and phone status.
3.3 Service
This section includes SIP, calls, video, RTSP server and web server.

720p SIP Door Phone with PoE
HDP-1100PT
14
3.3.1 SIP
This section includes SIP information, SIP registration, and intercom with control pad and
advanced settings. You can register door phone to your IP PBX on this page and intercom with
control settings.
Parameters Description
Qualia Service Tick this to connect with cloud server when using Cloud Bell App.
Registration Enable Tick this to enable registration.

720p SIP Door Phone with PoE
HDP-1100PT
15
Parameters Description
SIP Information Account and password of registration information in your IP PBX.
SIP Registrar IP address, port and expiry of your IP PBX.
Dial Button needs to be filled in IP address of control pad for
intercom. You can add one or more IP address of control pad.
Advanced Settings SIP transport, SIP local port, starting RTP port and IP address filter
enable/disable.
3.3.2 Calls
Here you can configure outgoing calls and DTMF code for door lock.
Parameters Description
Ring Time Limit Set the ring time where there is no answer.
Call Duration Limit Set the call duration during the call.
Door Unlock Key by
DTMF code Enter the DTMF code that could open door by VoIP phone. Please
refer to the appendix C for more details.

720p SIP Door Phone with PoE
HDP-1100PT
16
3.3.3 Video
You can modify the pixel of the door phone.
Parameters Description
Video Frame Rate
Defines the targeted frame rate of this video. For example, set the
frame rate to 15 fps, then the image will be updated for 15 frames per
second. User can set the desired max. frame rate versus video
quality under the limited bandwidth.
Video Resolution of
H.264 Resolution of the H.264 stream.
Video Quality of
H.264 The higher the quality is, the bigger the file size is. It might affect
Internet transmission speed if the file gets too large.
Video Resolution of
MJPG Resolution of the MJPEG stream.
Video Quality of
MJPG The higher the quality is, the bigger the file size is. It might affect
Internet transmission speed if the file gets too large.

720p SIP Door Phone with PoE
HDP-1100PT
17
3.3.4 RTSP Server
RTSP command of the door phone
Parameters Description
RTSP Server Enable To enable or disable the RTSP server
MJPG URL Set the MJPG output connecting route.
MJPEG Audio Type To select alaw or acc for MJPEG audio coding
H264 URL Set the H264 output connecting route.
H264 Audio Type To select alaw or acc for H264 audio coding
3.3.5 Web Server
You can change the account and password of login to the door phone.

720p SIP Door Phone with PoE
HDP-1100PT
18
Parameters Description
Account Account of login to the door phone.
Password Password of login to the door phone.
HTTP Port Default is 80.
3.4 Device
This section is about volume control and camera, and relay settings.
3.4.1 Volume Control
Here you can adjust volume of the door phone.
Parameters Description
Speaker Volume Speaker volume of the door phone.
Microphone Volume Microphone volume of the door phone.
AEC Enabled Enable/Disable AEC.

720p SIP Door Phone with PoE
HDP-1100PT
19
3.4.2 Camera
There are Brightness, Contrast, Flicker and Night Mode of the door phone.
Parameters Description
Brightness Brightness of the door phone.
Contrast Contrast of the door phone.
Flicker Wrong power line frequency makes images flicker. Make sure it
comes with the 50 or 60Hz format of your device.
Night Mode Tick this to enable night mode.
3.4.3 Relay
Set the relay time of the door lock.
3.5 System
This section can set up network and time, and upgrade firmware.

720p SIP Door Phone with PoE
HDP-1100PT
20
3.5.1 Network
Network setting of the door phone
Parameters Description
Network Type Select your network type: Ethernet or PPPoE.
Boot Protocol
Select your Boot Protocol: DHCP or Static.
DHCP: IP camera will get all the network parameters automatically.
Static IP: Please type in IP address, network mask, gateway, and
DNS server manually.
IP Address This address is a unique number that identifies a computer or device
on the WAN or LAN.
Network Mask Network Mask allows network traffic between hosts to be separated
based on the network's configuration.
Default Gateway
A gateway is a piece of software or hardware that passes information
between networks. You'll see this term most often when you either
log in to an Internet site or when your email is transient between
different servers.
DNS Server When you send email or position a browser to an Internet domain
such as xxxxx.com, the domain name system translates the names
into IP addresses. The term refers to two things: the conventions for
naming hosts and the way the names are controlled across the