Planet MCU-1400 User manual

MCU-1400/1900
their respective owners. Copyright © 2009 PLANET Technology Corp. All rights reserved.
PLANET Technology Corporation
11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C.
Tel: [phone] Fax: [phone]
Email: [e-mail] www.planet.com.tw
Quick GuideQuick Guide
MCU-1400/1900
2011-D00290-000
VERIFY THE CONTENTS INSIDE PACKAGE BOX
The package box should contain the items indicated below plus MCU-1400/1900. If any item is missing or damaged, please contact the seller immediately
STEP 1: Fasten 4 screws (2 on each side) to attach the rails
onto the chassis
STEP 2: Mount the system onto the rack
STEP 5: Fasten the L-shape bracket to the rack
STEP 10: Wait for 3 minutes until system boot up properly, you may now open your web browser, and input
http://172.16.0.1 to logon MCU web configuration page.
L-shape bracket x 2
CD-ROM Rail x 2
Quick Installation Guide Power cord
STEP 8: Connect Power cord STEP 9: Press the Power button once to switch
on the system
STEP 7: Connect Ethernet cable to Switch / Router and Eth0 port
Default username/password: admin/123
Default IP address: 172.16.0.1 (Eth0)
Note: Please refer to related chapter in user’s manual CD for further configurating
STEP 3: Hold the system firmly and fasten the system
to the rack
STEP 4: Mount the L-shape bracket onto the rail
in the back of the system
STEP 6: Fasten the L-shape bracket to the rail
Note: Make sure that you hold the system firmly while
fastening the system to the rack
(Ex: Switch)
(Ethernet Port)
(Switch/Router)
Ethernet Cable
Power cord
Eth0 Eth1
Note: Be careful to avoid unit drop and get hurt
in installation
Note: Follow the above procedures in reverse order to
dismount the system from the rack if necessary

MCU-1400/1900
their respective owners. Copyright © 2009 PLANET Technology Corp. All rights reserved.
PLANET Technology Corporation
11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C.
Tel: [phone] Fax: [phone]
Email: [e-mail] www.planet.com.tw
Quick GuideQuick Guide
MCU-1400/1900
2011-D00290-000
VERIFY THE CONTENTS INSIDE PACKAGE BOX
The package box should contain the items indicated below plus MCU-1400/1900. If any item is missing or damaged, please contact the seller immediately
STEP 1: Fasten 4 screws (2 on each side) to attach the rails
onto the chassis
STEP 2: Mount the system onto the rack
STEP 5: Fasten the L-shape bracket to the rack
STEP 10: Wait for 3 minutes until system boot up properly, you may now open your web browser, and input
http://172.16.0.1 to logon MCU web configuration page.
L-shape bracket x 2
CD-ROM Rail x 2
Quick Installation Guide Power cord
STEP 8: Connect Power cord STEP 9: Press the Power button once to switch
on the system
STEP 7: Connect Ethernet cable to Switch / Router and Eth0 port
Default username/password: admin/123
Default IP address: 172.16.0.1 (Eth0)
Note: Please refer to related chapter in user’s manual CD for further configurating
STEP 3: Hold the system firmly and fasten the system
to the rack
STEP 4: Mount the L-shape bracket onto the rail
in the back of the system
STEP 6: Fasten the L-shape bracket to the rail
Note: Make sure that you hold the system firmly while
fastening the system to the rack
(Ex: Switch)
(Ethernet Port)
(Switch/Router)
Ethernet Cable
Power cord
Eth0 Eth1
Note: Be careful to avoid unit drop and get hurt
in installation
Note: Follow the above procedures in reverse order to
dismount the system from the rack if necessary