Planika VALENTINO 1300 F User manual

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7
USER MANUAL
VALENTINO 1300 F, VALENTINO 1300 LF/FR,
VALENTINO 1300 LFR
G20/G25 (Natural Gas) G30/G31 (Propane-Butane/Propane)
Produced by:
Planika Sp. z o.o.
ul. Bydgoska 38
86-061 Brzoza
Poland

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 2
IT IS OBLIGATOR TO READ AND STORE THIS INSTALLATION
MANUAL.
TABLE OF CONTENTS
. INTRODUCTION ......................................................................................................................................................... 4
2. GENERAL INFORMATION .......................................................................................................................................... 5
3. SAFETY ....................................................................................................................................................................... 5
3. . Safety instructions ............................................................................................................................................ 7
3.2. Safety instructions for the use of gas cylinder .................................................................................................. 8
4. USAGE ....................................................................................................................................................................... 9
4. . First use ............................................................................................................................................................. 9
4.2. Discoloration of walls and ceilings .................................................................................................................... 9
5. REMOTE CONTROL .................................................................................................................................................. 0
5. . Display and buttons ........................................................................................................................................ 0
5.2. Explanation of symbols ...................................................................................................................................
5.3. Setting connection between the remote control and the receiver ................................................................
5.3. . Battery exchange ........................................................................................................................................ 2
6. USER MENU ............................................................................................................................................................. 3
6. . Eco Flow .......................................................................................................................................................... 3
6.2. Relay - control of additional optional lighting ................................................................................................ 4
6.3. Fan or damper control .................................................................................................................................... 4
6.4. The choice of control options ......................................................................................................................... 5
6.5. Date and time settings .................................................................................................................................... 5
6.6. Setting the time schedule ............................................................................................................................... 6
7. INSTALLATION MENU .............................................................................................................................................. 7
7. . Time format of 2-hour or 24-hour ................................................................................................................ 7
7.2. Time schedule ( day, 5 + 2, 7 days or manual) ............................................................................................... 8
7.3. The periods during the day (II, IV or VI) .......................................................................................................... 8
7.4. User Menu Settings ......................................................................................................................................... 9
8. CONTROL ................................................................................................................................................................. 9
8. . Manual control ................................................................................................................................................ 9
8. . . Ignition of the device .................................................................................................................................. 20
8. .2. Flame height adjustment ............................................................................................................................ 2
8. .3. Temperature regulation .............................................................................................................................. 2
8. .4. Temporary disruption of the temperature control ..................................................................................... 22

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 3
8. .5. Switching on and off the side sections of the furnace ................................................................................ 22
8. .6. Turning off the device ................................................................................................................................. 22
8.2. Automatic control - Time Schedule ................................................................................................................ 23
8.2. . Temporary change of temperature setpoint .............................................................................................. 23
8.2.2. Temporary disruption of the time schedule ............................................................................................... 23
9. SIGNAL QUALITY ...................................................................................................................................................... 24
0. TROUBLESHOOTING ............................................................................................................................................ 24
. MAINTENANCE .................................................................................................................................................... 27
. . Cleaning of the glass with anti-reflective coating ....................................................................................... 27
.2. Assembly of the glass .................................................................................................................................. 28
.3. Dissassembly of the glass ............................................................................................................................ 3
2. ENVIRONMENTAL PROTECTION .......................................................................................................................... 34
2. . The device ................................................................................................................................................... 34
3. WARRANTY .......................................................................................................................................................... 35
4. TECHNICAL SPECIFICATIONS ............................................................................................................................... 36
5. CONTACT DETAILS OF THE MANUFACTURER ..................................................................................................... 36

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 4
1. INTRODUCTION
Planika company designs and manufactures gas heating devices that meet the highest standards of quality, efficiency
and safety. This product has a CE label, which means that it meets the essential requirements contained in the
European Parliament and Council directive 2009/ 42/EC of 30 November 2009 relating to appliances burning gaseous
fuels and in accordance with standard EN 6 3 on convection space gas heaters, and norm EN 778:20 0.
Each gas fireplace produced by Planika is subjected to quality control, during which passes stringent safety tests. High-
quality materials used for its production guarantee the user a smooth and reliable operation of the device.
The device is supplied together with user manual as well as installation manual. Installation manual provides necessary
information in order to install the device in such way, as to run it properly and safely. In addition, you can find the
technical details about the device, information about maintenance and possible failures that may occur, together with
their possible causes and way of their solution.
WARNING! The installer must be certified and qualified professional in the field of gas heating and electricity and
should have all the required local law permissions.
CE Declaration of conformity
We hereby declare, that the design and construction of gas heating device by Planika meet the essential requirements
contained in the directive on gas appliances.
Product: Convection space gas heater with closed combustion chamber, equipped with concentric air combustion pipe
system with natural gravity, type C (without a fan) and the type of C3 and C9 (without a fan).
Type: VALENTINO 000 F, VALENTINO 000 LF, VALENTINO 000 FR, VALENTINO 000 LFR,
VALENTINO 300 F, VALENTINO 300 LF, VALENTINO 300 FR, VALENTINO 300 LFR
Directives: 2009/ 42/EC; 20 4/35/EU; 20 4/30/EU
Norms: NEN-EN-6 3; NEN-EN-6 3/A ; EN 778:20 0; EN 60335-2- 02
Factory quality control system in the company ensures that the devices produced in series, comply with the essential
requirements of the applicable WE directives and norms contained therein. This declaration shall be canceled in the
event of the introduction of any modifications of the device without the prior written consent of Planika.

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 5
2. GENERAL INFORMATION
VALENTINO gas fireplaces are gas powered heating devices with closed combustion chamber, which use first-class
advanced automation to control the gas valve. The device complies with European directives with regards to safety,
the environment and energy consumption. Thanks to the use of the concentric flue system, the air supplied to the
combustion chamber via the outer pipe is drawn from outside the building. The entire system is completely closed,
which prevents the exhaust gases entering directly into the room where the fireplace is located. This provides the
user with 00% security thanks to separation of the products of combustion, which are removed efficiently out of the
building through the inner pipe of concentric system.
VALENTINO Gas fireplaces series are intended for indoor use only, and can be powered by natural gas or liquefied
natural gas propane or propane-butane. The device is manufactured in four variants of glazing, in accordance with the
accessibility for each installed, so as to be able to fully meet the needs of even the most demanding customers.
Regardless of the glazing and the length of the chimney, VALENTINO fireplaces are equipped with automatic control
and protection of the same type, and their connection to the gas system and the flue system is identical. The user also
has the option of choosing the version of the interior of the fireplace and control it by using remote control supplied
together with the device, through automation system of intelligent buildings or use for this purpose a built-in
thermostat unit.
3. SAFET
WARNING! It is obligatory to carefully read the installation and operating instructions before installing and using the
fireplace series VALENTINO. This manual should be retained for the life of the device.
WARNING! The device must be installed in accordance with the relevant national and local regulations. Connection to
the flue pipe, wall and roof transitions as well as all elements used to install the fireplace should be made in accordance
with applicable standards of national construction law.
To ensure the safe installation and trouble-free operation, please use the following precautions and observe the
following safety rules:
•Read installation manual and user manual before installation and first use of the device.
•The device can be installed and serviced only by certified and skilled professional specializing in the field of
gas heating and electricity.
•Installation of the unit must allow easy access to all components subject to maintenance and service, and to
allow free access to the components of the system closing the front glass.
•Do not use the device before you fully install it in the chosen destination.
•Fireplace series VALENTINO should be monitored at least once a year in accordance with this installation
manual and as well as all applicable national and local regulations concerning safe installation and use of gas
appliances.

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 6
•Make sure that the information on the nameplate are consistent with the local type of domestic gas and
pressure.
•Do not change the structure of the device and its sealed components or modify the default settings of the
fireplace.
•The components of the control system with the gas valve cannot be exposed to moisture.
•Carbon dioxide (CO2) or powder extinguisher must be placed near the unit.
•Before connecting the device you should familiarize yourself with all connecting schemes (including electric),
set out in the manual.
•The first time you turn on the fireplace VALENTINO, it is necessary to use it at the maximum level of the flame
for a few hours so that the elements warm themselves, and possible small residues of paints, coatings and
lubricants will evaporate.
•During the first hours of use of the device, additional ventilation and ventilation of the room is recommended,
to quickly remove the characteristic smell fire resistant paint.
•WARNING! When you first start your device, the installer should perform the leak test on all gas connections,
check the connections of all elements of the system (including the proper connection to the concentric air
combustion system) and check the correct operation of all the items, in particular system of ignition and flame
failure protection system.
•Do not move the device during its operation.
•The surface of the fireplace series VALENTINO may strongly heat up during use - up to more than 00 °C.
•WARNING! Accessible parts of the devices, including the glass, can become very hot. You absolutely must
protect children from contact with the working device!
•Do not operate the machine without inserting the front glass.
•In case of failure of any of the glass panels, please contact your service provider or distributor.
•The device should be installed away from flammable materials.
•All metal parts of the fireplace series VALENTINO are constructed of materials resistant to rust or covered with
corrosion coating.
•Never leave the fireplace VALENTINO unattended (as in the case of any other type of fireplace or fire in the
room). Fireplace series VALENTINO should be installed out of reach of children, unauthorized persons and
animals so direct contact with hot parts of the fireplace is not possible.
•In case of feeling any gas leaks, immediately turn off the fireplace and, depending on the type of fuel, close
the main valve on the gas cylinders LPG or close the valve supplying natural gas to the device. You should also
ventilate the room in which the fireplace is installed and contact the service staff.
•If the unit is not used for a long time, depending on the type of fuel, close the main valve on the LPG cylinder
or close the valve supplying natural gas to the device.

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 7
3.1. Safety instructions
•WARNING! The device is powered by a voltage of 230 V AC, 50 Hz
•VALENTINO fireplaces are not standalone devices and are intended only for installation.
•Co najmniej raz w roku należy zlecać przegląd konserwacyjny urządzenia. At least once a year you should make
an overview of the device maintenance.
•Always observe the minimum distances between combustible walls of the housing and the device.
•Combustible materials should be placed no closer than within m from the unit.
•Only decorative accessories attached to the device by the manufacturer should be placed on the furnace (logs,
stones, vermiculite or ash imitation). These accessories should be installed as described in this manual.
Incorrect placement of decorative materials may result in shortening the useful life of the furnace and its
damage.
•WARNING! Make sure you don’t place any decorative elements around the ignition and ionization electrodes.
•Before the final installation and before starting to construct the fireplace housing, make sure that blast-
resistant flaps at the top of the device are in correct position and whether they were properly attached to the
sealing surface.
•If the ignition of the device is incorrect or the Fireplace will fail, you should close the gas valve and contact the
installer and make sure that the device is not energized.
•If there is no ignition of the device after three restarts and permanent lock of the device activates, reset by
disconnecting from the power source may be impossible. In such cases, please contact your distributor or
installer.
•In the event of damage or break the glass, the device cannot be used and you must close the gas valve and
immediately request glass
•The remote control should be kept out of reach of children and unauthorized persons not familiar with the
unit's User Manual.
•If the device is not used for an extended period of time, close the gas valve and remove the batteries from the
remote control. This will prevent damage due to battery leakage.
•It may happen that the device will turn off automatically and immediately turns on. This is not a failure, but
test procedure resulting from the design and configuration of the driver, because the control device is subject
to strict safety requirements. From the moment you connect a device driver to a power source, the driver will
perform this test every 24 hours. If the device is currently lit, it goes off and immediately turns on again.
WARNING! Operate the device using the remote control with use of the built-in thermostat or (optional) tablet
with a special application or home automation system, the device can turn on when you are not at home.
Therefore, in such cases, you should take extra precautions before switching on the machine without
supervision (eg. an additional switch of electricity on the power cord; closing the ball valve on the gas supply
line to the device) in order to avoid damage to objects or injuries and the use of to all safety instructions in
this manual.

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 8
3.2. Safety instructions for the use of gas cylinder
•Use only the type of gas and pressure specified on the label by the manufacturer.
•Gas cylinders should always be in an upright position - both during use and transport.
•A storage of the gas cylinder should be located in a place easily accessible to allow its immediate closure.
•During installation, never approach the gas flame or any other source of fire.
•Gas cylinder should not be closer than .5 m from the fireplace VALENTINO.
•Any leaks should be located using a mixture of water and foaming cleaning fluid. The resulting air bubbles
indicate a leak.
•Always use a pressure reducer between the cylinder and the device. Replace pressure regulator at least every
5 years. Permissible pressure: 30mbar, 37mbar (recommended), 50 mbar. Use only regulators that meet the
requirements of European Standard EN 6 29.
•Use only approved and certified cables connecting gas (flexible hose). Replace them at least every 2 years.
•Flexible hose supplying gas to the unit should be located away from sharp edges and hot surfaces. Avoid bends
and twists of flexible connections along the whole length.
•Note that the gas cylinder LPG should be installed in well-ventilated areas. LPG gas is heavier than air and its
accumulation on the substrate can lead to the formation of explosive mixtures.
•Optional housing, which cylinder of LPG will be placed at, must have adequate ventilation. It must have an
upper ventilation opening above the top of the cylinder (with min / 00 base surface of the installation) and
a lower vent opening at its base (with min /50 base surface of the installation).
•Turn off gas cylinder, if the device is not in use.
•Filling the gas cylinders should only be done at certified gas filling stations.
•Exchange of empty bottles for full should take place only at authorized points.

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 9
4. USAGE
Before first use of the fireplace, make sure that all connections of individual elements of the system have been made
according to the instructions. Incorrect connection of system components for gas or faulty connection concentric air
combustion system may cause an improper operation of the device or damage it.
4.1. First use
The first time you turn on the fireplace VALENTINO, it is necessary to use it at the maximum level of the flame for few
hours so that the elements warm themselves, and possible small residues of paints, coatings and lubricants will
evaporate. During this period, additional ventilation and ventilation of the room where the appliance is installed is
recommended, because the characteristic smell of evaporating powder paint may be felt for about another hour of
use. It can be particularly sensitive to volatile vapors may be pets (mainly birds).
If during your first startup of the device, sediment will appear on the inner surface of the glass (glasses), turn off the
device and allow it to cool to room temperature, and then clean the glass (see section . ). The formation of the
RAID is caused by burning volatile components of paints, which initially may also have an impact on the image of the
flame.
Fireplace installed in the housing should be fired for the first time after complete drying of all the walls of housing.
This prevents the formation of cracks due to shrinkage of the materials. If the walls of the fireplace housing are made
of stone materials, leave it to dry for at least 6 weeks prior putting the unit into operation.
4.2. Discoloration of walls and ceilings
When using gas heating, you can meet with a phenomenon of electrolytic colouring of walls and ceilings. It is caused
by the movement of air convection, and dust particles contained therein. Brown discoloration may also occur during
combustion of substances as a result of inadequate ventilation, smoking, the use of candles and oil lamps. These
problems can be partially prevented by ensuring adequate ventilation the room in which the device is located.

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 0
5. REMOTE CONTROL
Urządzenie wyposażone jest w bezprzewodowy, radiowy pilota zdalnego sterowania (868MHz). Umożliwia on zarówno
ręczne sterowanie urządzeniem, jak również sterowanie na podstawie harmonogramu czasowego lub zadanej
temperatury w pomieszczeniu poprzez wbudowany w pilocie termostat. Temperaturę i wysokość płomienia można
regulować w trybie manualnym. W trybie harmonogramu czasowego urządzenie sterowane jest wyłącznie w oparciu
o zadaną przez Użytkownika temperaturę, w porównaniu z temperaturą w pomieszczeniu, w którym zainstalowane
jest urządzenie (na podstawie odczytów z termometru znajdującego się w pilocie zdalnego sterowania).
The device is equipped with Wi-Fi, radio remote control (868 MHz). It allows both manual device control, as well as
control based on schedule or set temperature in a room by the built-in remote control thermostat. The temperature
and the flame height can be adjusted in manual mode. In Schedule the unit is controlled solely on the basis of specified
by the user, in comparison with the temperature in the room where the device is installed (based on readings from
the thermometer located in the remote control).
5.1. Display and buttons
Picture 1: Rmote Control

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7
5.2. Explanation of symbols
5.3. Setting connection between the remote control and the receiver
After replacing the batteries or during your first installation, you must establish the communication code between the
remote control and the receiver to be able to use the wireless remote control. The receiver is in the mounting bracket
together with the gas valve and electronic control unit.
The remote control can communicate with a device only when it is registered on the device . To do this, you must do
the following:

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 2
•Press and hold the button on the remote control for 0 seconds.
•Then press for a short time the same button several times until screen „ ”
appears.
•Briefly press buttons and at the same time until screen 2 appears. After a successful completion of
the process of setting up the communication, startup screen will be displayed.
If the connection fails, screen will appear again.
Setting a new communication code is required after each battery replacement or after a
power failure for more than 5 minutes.
WARNING! It cannot be ruled out, although it is unlikely that the ignition of the device can be started unintentionally
by other remote controls (for example, remote control of another gas heater, car remote control or remote control
for garage doors working in the 868 MHz band). As a result, the device can be ignited at the wrong time, also during
our absence. In the event of such situation, you must take the following preventive measures:
•establish a new communication code between the remote control and the receiver (if accidental ignition took
place).
•Close the gas valve near the device, if the device will not be used for an extended period of time. This is the
safest remedy.
•Change the position of the receiver to minimize the possibility of receiving unwanted radio signals.
•Follow the specific instructions of the security measures, even if the device is not in use.
5.3.1. Battery exchange
Before using the remote control you must place the two supplied batteries (type AA). After inserting the batteries and
after connection to receiver, the remote control is ready to operate the fireplace by manual adjustment of the flame
height. To extend battery life, after some time the button was last pressed, the screen goes blank, unless the device is
turned on.
If the display shows the flashing symbol , replace the batteries. If the batteries are completely discharged, the
display goes off. Therefore, you should replace the batteries in the remote control. To change it, you should:
•Remove the back cover of the remote control by moving it a few millimeters down (Picture 2, Part ) and lifting
it to the top.
•Remove the old batteries from the housing.
•Place the new battery pack in the housing (Picture 2, Part 2).
•Mount the back cover of the remote control, placing the tabs A and B of the rear cover (Picture 2, Part 3) in
the corresponding notches of the remote control housing (Picture 2, Part 2).

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 3
•Push the rear cover upwards to lock it.
•After replacing the batteries, re-establish communication code, the current time and day of the week (it is
necessary if you use the time schedule).
Picture 2: Battery exchange in the remote control
WARNING! Do not throw exhausted batteries together with other household waste, but dispose of them as chemical
waste.
6. USER MENU
The user menu is composed by default with five screens that allow you to access the following features:
•Screen : Eco Flow
•Screen 2: Relay (additional electric receiver such as lighting)
•Screen 3: Fan / Damper
•Screen 4: Choice of control options
•Screen 5: Time menu
If the user do not plan to use all the options and related features available in the user Menu, the user can disable it
through the appropriate configuration in the installation Menu. These features will no longer be visible in the user
Menu on the remote control.
To activate the user Menu, you should press and hold button for 2 seconds. You can go out of User Menu by
pressing button or after waiting five seconds of pressing the last button.
6.1. Eco Flow
Eco Flow, allows you to change the height of the flame automatically, within a programmed range, without user
interaction, and without need to manually change the height of the flame. This enables you to save energy and reduce
gas consumption with satisfaction of preserving the beautiful appearance of the flame Using the remote control, this
feature can be enabled and disabled. Please note, however, that this is only possible when the device is turned on. By
default, the Eco Flow is turned off.

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 4
To activate or deactivate the feature Eco Flow, you should:
•Go to the Screen of the user menu, by pressing and holding the button
for 2 seconds.
•Activate or deactivate the Eco Flow by pressing the arrow keys on the
remote control or („ ” means activating and „0” means
deactivating of Eco Flow). Screen 1.
6.2. Relay - control of additional optional lighting
Gas valve control electronics gives you the ability to connect an optional lighting (for example, to highlight the Interior
of the housing) or any other electric receiver and allows you to control it with the remote control. Built-in relay can be
used to control the AC Receiver (max 230V AC\/0, 5A).
This feature can only be turned on and off by using the remote control. To activate or deactivate receiver connected
to electric relay, you must:
•Go to Screen 2. Of the user menu, by pressing and holding button
for 2 seconds. Then, again press the buton .
•Enable or disable electric receiver function by pressing the arrow
buttons on the remote control or („ ” means activating and
„0” means deactivating).
Screen 2.
6.3. Fan or damper control
Electronics controlling gas valve gives you the ability to connect and control via optional fan or throttle powered with
AC (max 230V AC/0, 8A), mounted for example in the wall of the fireplace housing. The fan can be used to improve air
circulation within the housing or to distribute warm air from inside the housing to the other rooms.

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 5
Using the remote control this function can only be switched on and off. To enable or disable connected fan you should:
•Go to Screen 3. Of the User Menu, by pressing and holding the button
for 2 seconds. Then briefly press twice the button .
•Enable or disable fan by pressing the arrow buttons on the remote
control or („ ” means activating and „0” deactivating).
Screen 3.
6.4. The choice of control options
The remote control is configured by default to manual control mode. To use the time schedule, select the appropriate
option in the installation Menu (Chapter 7). After proper configuration in the installation Menu, features of the time
schedule will be available and you will be able to find them on the screen 4 (and subsequent) in the user Menu.
To make the choice of how to control a fireplace:
•Go to Screen 4 of the User Menu, by pressing and holding the
button for 2 seconds. Then briefly press three times the
button .
•There are three possible control modes of Fireplace control,
symbolized by two flashing symbols:
oManual control with adjustable flame height
oManual control with the temperaturę control,
oTime schedule (temperaturę control).
Screen 4.
•the desired way to control a fireplace you should select by pressing the arrow buttons or on the
remote control.
•Leave the Menu by pressing a button or after waiting five seconds of pressing last button.
6.5. Date and time settings
In the Time Menu (Screen 5 User Manual) the following settings are available:
•Time,
•Day of the week,
•Time schedule.

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 6
To change the current settings, you should:
•Go to Screen 5 in the User Menu, by pressing and holding the
button for 2 seconds. Then briefly press four times the
button . The currently set time starts flashing.
•Using the arrow keys or set the correct time on the
remote control.
•Press again the button . Days of the week will flash.
•Using the arrow keys or se the correct day of the week.
Open square indicates the selected day. WARNING! Weekdays are not visible if you choose a one-day time
schedule.
6.6. Setting the time schedule
Depending on the choices made in the Installation menu available options may include the following time schedule:
•Time schedule with the same settings for each day
•Time schedule with separate settings for weekdays (Monday to Friday) and the weekend
•Time schedule with separate settings for each day.
For each day, you can set two, four or six different periods. Time schedule can easily set the start time and set
temperature point for each period. Setting all time schedules is done in the same way, regardless of the amount
selected in the Installation menu.
To change settings of the time schedule you should:
•Press and hold the button for 2 seconds, then again briefly press
the button six times . Start time of the first period flashes.
•Using the arrow keys or on the remote control set the correct
start time of the first period.

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 7
• Press the button again. Desired temperature of the first period
flashes.
•Using the arrow keys or set the correct temperature and time
on the remote control.
•Press the button again and repeat the above steps to set the
desired start time and the setpoint temperature for all periods and
days.
• It is also possible to shut down the device at specific time in the current
set period. To do this, select „ --,-" when setting the desired
temperature.
7. INSTALLATION MENU
The following options are available in the installation menu:
•Time format of 2-hour or 24-hour,
•Time Schedule ( day, 5 + 2, 7 days),
•The number of periods during each day (II, IV or VI).
To activate the Installation menu you should exit the User Menu (if it is enabled), and then press and hold the button
for 0 seconds. You can leave Installation Menu after pressing the button or after waiting five seconds of
pressing last button.
7.1. Time format of 12-hour or 24-hour
To change the time display format:
•Press and hold the button for 0 seconds. The currently selected time display format starts flashing.
•Change the format of the time display by pressing the arrow buttons on the remote control or .

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 8
7.2. Time schedule (1day, 5 + 2, 7 days or manual)
To change the time schedule you should:
•Press and hold the button for 0 seconds, and then briefly press again the button. Screen with one
of the four currently used timetable will appear. Screen with the symbol means the manual mode and the
lack of the currently selected time schedule. In this case, it is only possible to manually control the height of
flame.
•Select the desired time schedule by pressing the arrow keys on the remote control or :
oTime schedule with the same settings for each day.
oTime schedule with separate settings for weekdays (Monday to Friday) and the weekend.
oTime schedule with separate settings for each day.
oManual Mode.
7.3. The periods during the day (II, IV or VI)
To change the number of available periods during the day (II, IV lub VI) you should:
•Press and hold the button for 0 seconds, and then briefly press again the button. The currently
selected number of periods per day starts flashing.
•Select the desired number of periods per day by pressing the arrow keys on the remote control or :
oII – two periods during the day,
oIV – four periods during the day,
oVI – six periods during the day,

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 9
7.4. User Menu Settings
It is possible to configure the options in the User Menu, including the deactivation or change the default settings of
Eco Flow function, work status of Relay "L" and use of Fan/Damper "B".
To change the default settings for the options that are available in the user Menu you should:
•Press and hold the button for 0 seconds, and then briefly press again the button. Current state of
function Eco Flow marked with digit will start flashing.
•Select the desired state of the option available in the user Menu by pressing the arrow buttons on the remote
control or :
o0 = not available in the menu
o = by default, always off
o2 = by default, always on
o3 = last position
•To go to the configuration of the Relay operating mode and the Fan support you must again press the
button.
8. CONTROL
The remote control has a display and four buttons. Thanks to this, operation of the device is simple and settings can
be easily changed. There are two settings Menu available:
•User Manual (see chapter 6)
•Installation Manual (see chapter 7)
To activate the User Menu, press and hold the button for at least 2 seconds. To activate the Installation menu,
press and hold the button pressed for 0 seconds.
8.1. Manual control
After selecting the device manual control in the user Menu, the device switching on and off as well as the temperature
control or the height of the flame is carried out manually. Otherwise (if the device is configured in time schedule mode)
manual control of the device is not possible, and the process of switching on and off is performed automatically
according to the set switch-on time and according to set target temperature in the room.

Copyright Planika Sp. z o.o. www.planikafires.com IG0058#00 3 .03.20 7 20
WARNING! If you select the automatic mode of controlling the fireplace, it is important that the remote control is not
in the immediate vicinity of the fireplace and lay freely in easily accessible location. This will allow you to avoid passing
incorrect information by the thermometer (integrated in the remote control) to receiver controlling the operation of
the fireplace, about the temperature in the room.
8.1.1. Ignition of the device
To start the process of firing the device, which is ready for use in manual
mode, simultaneously press and hold for at least 2 seconds and
buttons on the remote control. The gas supply to the furnace will open and
you will hear the sound of working ignition electrodes.
During the ignition on the screen of the remote control, symbols and
will start flashing, which indicates the fact that, the ignition process of the
device is taking place and you will also see the hourglass symbol, which will
not let you manipulate the fireplace. In the first place the middle section of
the device will be lit on 50% of its power. After about one minute solenoid
valve gas supply turns on to the side section of the furnace and the device
switches to its full performance. The hourglass symbol will disappear which
indicates the end of the ignition process.
WARNING! If there is no ignition of the device after three restarts and the permanent device lock activates, it may be
impossible to reset it by disconnecting the power source. In such cases, contact your dealer or installer.
When the symbol on the screen will disappear and symbol will stop
flashing, it means that the ignition of the device was completed correctly, and
the fireplace is ready to use. From that point on, manual flame height
adjustment will be possible.