Platinum Spas Control TP600 User manual

01
Control TP600
Hot Tub Manual

02 03
GREAT
NEWS
ON YOUR
NEW SPA
PURCHASE.
Your Hot Tub is designed and manufactured with the nest components available
and is engineered for comfort, low maintenance, and durability in mind.
This manual will help you to determine the best way to take care of your spa based on the
amount of use and the type of environment your spa is installed.
It is very important that you take me to read the enre manual before using your spa.
Within in this manual are important start-up guidelines and maintenance procedures as well
as safety precauons that must be followed to ensure the prolonged life of your spa and the
safety of the people using the hot tub.
Failure to follow start-up procedures may result in damage to your Hot Tub and void your
warranty. Please feel free to call Superior Spas Ltd if you have any further quesons aer
reading this manual. Your Hot Tub comes with a warranty, informaon relang to your
warranty can be found in Secon 12 of this manual.
We hope you enjoy many years of fun and relaxaon in your new Hot Tub.

04 05
CONTENTS
1610
24
06
18
12
25
08
20
13
26
Secon 6
Control panel
operaons
Secon 3
Electrical
requirements
Secon 9
Prepare your spa
for holiday
Secon 1
Important safety
informaon
Secon 7
Maintenance
Secon 4
Delivery of
your spa
Secon 10
Spa
winterizaon
Secon 2
Pre-installaon
& set-up
Secon 8
Water care
Secon 5
Checklist before
seng up your spa
Secon 11 / 12
Servicing
& Warranty

06 07
1. WARNING: To reduce the risk of
injury, do not permit children to use
this product unless they are closely
supervised at all mes
2. DANGER: Risk of accidental drowning.
Extreme cauon must be exercised to
prevent unauthorized access by children.
To avoid accidents, ensure that children
cannot use this spa unless they are
supervised at all mes
3. DANGER: Risk of injury. The sucon
ngs in this spa are sized to match
specic water ow created by the pump.
Should the need arise to replace the
sucon ng or the pump, ensure that the
ow rates are compable. Never operate
the spa if sucon ngs are broken or
missing. Never replace a sucon ng
with one rated less than the ow rate
marked on the original sucon ng
4. DANGER: Risk of Electrical Shock.
Install at least 5 feet (1.5m) from all
metal surfaces. As an alternave, spa
may be installed within 5 feet (1.5m) of
metal surfaces if each metal surface is
permanently connected (bonded) by a
minimum ground wire
5. DANGER: Risk of Electrical Shock. Do
not permit any electrical appliance such
as a light, telephone, radio, television, etc.
within 5 feet (1.5m) of a spa unless such
appliances are installed and built-in by the
manufacturer
6. ELECTRICAL SUPPLY: The electrical
supply for this product must include a
suitably rated switch or circuit breaker to
open all ungrounded supply conductors
to comply with the naonal electrical
standards. This disconnect must be readily
accessible and visible to the spa occupant
but installed at least 5 feet (1.5m), from the
spa water
7. WARNING: To reduce the risk of injury:
a) The water in the spa should never
exceed 40°C (104°F). Water temperature
between 38°C (100°F) and 40°C (104°) is
considered safe for a healthy adult
Lower water temperatures are
recommended for young children and
when the spa use exceeds 10 minutes
b) Since excessive water temperatures
have a high potenal for causing fetal
damage during early months of pregnancy,
pregnant women should limit spa water
temperatures to 38°C (100°F)
c) Before entering a spa, the user
should measure the water temperature
with an accurate thermometer since
the tolerance of water temperature
regulang devices varies
d) The use of alcohol, drugs, or
medicaon before or during spa use
may lead to unconsciousness with the
possibility of drowning
e) Obese persons and persons with a
history of heart disease, low or high blood
pressure, circulatory system problems, or
diabetes should consult a physician before
using a spa
f) Persons using medicaon should consult
a physician before using a spa since some
medicaon may induce drowsiness while
other medicaon may aect heart rate,
blood pressure, and circulaon
8. AUDIO/VIDEO EQUIPMENT
WARNINGS (Oponal equipment based
on model)
CAUTION: Risk of Electrical Shock. Do not
leave compartment door open
9. CAUTION: Risk of Electrical Shock. Replace
components only with idencal components
10. WARNING: Prevent Electrocuon.
Do not connect any auxiliary components
(for example cable, addional speakers,
headphones, addional audio/video
components, etc.) to system
11. CAUTION: Risk of Electrical Shock.
Do not service this product yourself as
opening or removing audio covers may
expose you to dangerous voltage or
other risk of injury. Refer all servicing to
qualied service personnel
12. CAUTION: Risk of Electrical Shock. When
the power supply connecons or power
supply cord(s) are damaged; if water is
entering the audio / video compartment
or any electrical equipment compartment
area; if the protecve shields or barriers
are showing signs of deterioraon; or if
there are signs of other potenal damage
to the unit, turn o the unit and refer the
servicing to a qualied service personnel
13. MAINTAIN: This unit should be subject to
periodic roune maintenance (for example,
once every 3 months) to make sure that
the unit is operang properly
14. CAUTION: Do not operate audio video
controls while inside the spa
15. INSTALLATION of the spa for other than a
residenal dwelling will result in voiding the
manufacturer’s warranty
16. CAUTION: Do not bring any object into
the spa that could damage the spa shell
17. CAUTION: Never insert any object into
any opening
18. WARNING: Do not sit on the spa cover or
place objects on it
19. MAINTAIN: Remove any water or debris
that may collect on the spa cover
20. WARNING: Do not use the spa
immediately aer strenuous exercise
21. WARNING: If you feel pain or dizziness at
any me while using the spa, disconnue
use and contact a physician
22. WARNING: To reduce risk of injury it is
especially important that persons with pre-
exisng health condions or problems such
as obesity, heart disease, high or low blood
pressure, circulatory problems, pregnancy
or diabetes to consult their doctor before
using the spa
23. WARNING: Observe reasonable me
limits when using the spa. Long exposures
at high temperatures can cause high body
temperatures. Symptoms may include
dizziness, nausea, fainng, drowsiness, and
reduced awareness. These eects could
possibly result in drowning
24. WARNING: The spa jets produce a stream
of water with relavely high pressure
Prolonged exposure of localized area of the
body may cause bruises to the skin
25. IMPORTANT: The include warning sign
must be posted where all users of the spa
can see and read it
26. WARNING: To avoid risk of drowning. The
Spa cover should be in place and properly
latched when spa is not in use
27. IMPORTANT: Read and understand the
warnings on the spa cover
28. MAINTAIN: Proper water chemistry is
necessary to maintain the water and prevent
possible damage to spa components
When installing and using this electrical equipment be sure to
follow these basic safety precauons:
Secon 1
IMPORTANT SAFETY INFORMATION

08 09
Selecng a site for your spa
Choose an area in your garden that will be
suitable for your Hot Tub, you may wish to
consult your electrician to ensure the correct
electrical supply can be provided before
preparing the base for the hot tub to sit on. An
area in front of your hot tub should be clear so
that grass and debris are not transferred to the
water. Allow access for steps.
Preparing your base
An un-level base may cause your spa to run
ineciently and cause major ongoing faults.
When creang your base remember it must
be; at, rm and reinforced if you plan to
place your hot tub on a raised plaorm, such
as decking. Please take into consideraon the
average weight of lled hot tub is 1500kg, you
will then need to account for the weight of 4-6
people, plus it will be placed here for a long
period of me.
PLEASE NOTE – If you decide to posion
your hot tub in the ground/pit or with decking
built around it, you will need a design plan
to allow access to all side for maintenance
and repairs, 600mm around each side
is required to ALL sides of the spa, any
obstacle’s blocking the access may result in
rescheduling. Revisits may be chargeable.
When you have decided on the posioning
of your hot tub, it is fundamental that a
solid foundaon is in place, grass will not be
suitable. Please note, it is the responsibility of
the customer to provide a suitable base that is
at, level and solid to prevent distoron from
occurring. Any structural damage caused by
improper base or base failure may invalidate
manufacturer’s warranty.
An ideal base would be concrete 100 –
150mm thick. However, exisng pao slabs
and block paving may also be used. Wooden
decking is also a popular base, however,
please ensure your base can hold the weight
of the hot tub, water and people in it. Please
refer to Secon 1 for the weight details of
your spa. Using “packers” to level the spa is
not acceptable
Please Note: Bases must be prepared in
plenty of me prior to delivery, thus allowing
me for the concrete, etc to fully cure. Any
revisits will be chargeable
Service Access
Access is required around the hot tub for
any future maintenance, ideally 600mm. If
this is not praccal then the hot tub must be
emped of water prior to our visit so that the
hot tub can be moved to allow access.
Think about
When deciding on the nal locaon of your
hot tub, please take into consideraon what
accessories you have ordered for your spa.
For example…
• Have you allowed enough space (8 inches
is needed) to let your cover fall behind your
spa when using your cover lier?
• Have you prepared the base to allow room
for the steps? 700mm is what we recommend
Secon 2
PRE-INSTALLATION & SET-UP
Access to the desired nal hot tub posion
It is very important that you have adequate
access for the size of the spa you have chosen.
Obtain the dimensions of your chosen hot
tub and check the route of access for the hot
tub. Check the widths & heights of doorways,
passages and gates to make sure the hot tub can
pass through. Gates, fences and doors may need
to be removed prior to delivery, the delivery
team will not do this for you.
Make sure that there is nothing protruding
such as drainage pipes, steps or sills that could
obstruct the way.
Check to see if there are any low roofs or
branches that would hinder vercal clearance.
If there are any corners on the path to your
designated installaon site, check to see the
hot tub will pass. The route to where the hot
tub is to be sited should be at and level and
not so ground. Check and inform us if there
are any slopes, retaining walls, steps or level
dierences that may cause problems. Any
extra resources required such as cranes or hiab
vehicles would be an addional charge and
would need arranging by yourselves through a
third party company.
Under special circumstances, where there is
no clear or easy route, a crane can be used to
posion your hot tub. Please contact a local
crane company to arrange this service if you
think it may be necessary. Please note that
the cost of the crane would be charged to you
and not included in our price.
Personnel
We supply a suitable amount of personnel
to deliver the hot tub on our hot tub cart or
spa sled and posion in place, should any
further personnel be required then this would
be down to yourselves to arrange for your
delivery date.
Our colleagues will NOT be able to remove
the hot tub from the hot tub cart/ sledge
unl it reaches the base where it will be
permanently situated.

10 11
Electrical Requirements and Connecons
Before installing a hot tub, the appropriate
electrical supply must be installed, inspected
and conrmed as in line with government
Regulaons. Below is a simple guide to make
sure your electrical supply is in line with the
appropriate regulaons.
Please see Secon 1 for the electrical
requirements of your hot tub.
Hot tubs must have a suitable electrical supply
in order to run, as they have a specic secon
in the 16th edion IEE (Instute of Electrical
Engineers) Regulaons. Do not aempt to
install the electrics yourself unless you are a
fully qualied electrician as the government
introduced a law in January 2005 which states
that most electrical work in UK households
must be carried out by a ‘competent person.
This means that Electrical safety requirements
have been included in a new Part P of the
Building Regulaons.
What is Part P?
The law introduced by the Government in
2005 states that anyone carrying out xed
electrical installaons in English and Welsh
households must ensure they are:
• Designed and installed to aord appropriate
protecon against Damage, whether that is
mechanical or thermal, so that they do not
present any danger in the form of electric
shocks or re hazards
• Suitably inspected and tested in order to
verify that they meet the relevant equipment
and installaon requirements.
• If you have a new circuit installed in your
home, it is a legal obligaon to have it
inspected and tested to ensure that it is
compliant with Part P. This can be achieved
in one of two ways:
1. Appoint an electrical contractor who
is registered with a competent person
scheme. Visit the websites of the following
organisaons if you are unsure of who is Part
P qualied:
NICEIC – www.niceic.org.uk
NAPIT – www.napit.org.uk
ELECSA – www.elecsa.co.uk
BSI – www.bsi-global.com/kitemark
BRE – www.partp.co.uk
OR
2. Appoint a contractor who is not Part P
registered, but contact your local authority’s
Building Control Department rst as the work
will have to be inspected and tested by your
local authority before it can be conrmed and
signed o. There is a charge for this service.
Whichever route you choose to take, you will
receive a Part P cercate to conrm that
the electrical work in line with government
regulaons. From post 2007 this paperwork
must be kept on le and presented, even
if you sell your house as part of the Home
Seller’s Packs.
We, as your hot tub retailer, can liaise with
your electrical contractor regarding the
exact specicaon for your chosen hot
tub model. However, you must meet the
following specicaon:
• The hot tub must be hard wired on its
own fused spur back to your household
consumer unit (i.e. the hot tub should not
share a supply with any other appliances.)
• The hot tub should be appropriately
protected by a suciently rated MCB
(mains circuit breaker) and should cover
the maximum amperage pull of the hot
tub plus 25% to allow for brake torque (i.e.
the rush of current when pumps are rst
turned on.) So, for example, a hot tub that
has a maximum current draw of 20 amps
should be ed with a 25amp MCB.
• Your hot tub should be protected against
earth faults also, by an RCD (residual
current device). This is a trip switch which
works to prevent the danger of electric
shocks from damaged or waterlogged
cables and connecons. A suitable rated
30Ma RCD is what is recommended
• Any outdoor cabling should be suitably
protected from damage by either laying
protecve ducng (pc pipe) below ground
or by using SWA (steel wired armored)
cable. Your electrician will calculate the size
of cable required dependent upon loading
and the distance from the mains supply.
‘Plug & Play’ Hot Tubs (13 AMP)
Electrical Requirements
13AMP (plug & play) hot tubs come ed
with a 3 pin plug which is equipped with an
RDC protector, this RCD protector means the
plug is much larger than a standard plug so
adequate water protecon will be needed. We
recommend waterproof casings such as:
Cable length 2m.
The plug will simply plug into a standard
domesc power supply*.
2 AMP and 40AMP Electrical Requirements
A 6mm² 3-core SWA cable is needed for a
32AMP hot tub and a 10mm² 3-core SWA
cable is needed for a 40AMP hot tub. An IP65
Rotary Isolator Switch is recommended in order
for the hot tub to be isolated outdoors in an
emergency or for service work. This is a rotary
on/o switch must be sited at least 2 meters
away from the hot tub so that users cannot be
in the hot tub whilst touching the switch.
A suitable weather proof block connector can
be ed to the end of the tail from the isolator
in order for the hot tub to then be directly hard
wired into the weatherproof block connector
inside the hot tub. Waterproof gland packs
should be used to prevent ingress of water on all
electrical connecons (2 at the isolaon switch).
It must be ensured that all earth cables
are clearly colour coded with green/yellow
insulang tape, or an earth sleeve.
If you have booked our full installaon package,
our installaon team will commission the Hot
Tub and check everything is fully operaonal
before the hot tub is ‘handed over’ to you, give
you instrucon on the control operaon and
provide chemical training.
If you are in any doubt about the required
electrical guidelines you should seek professional
advice from a fully qualied electrician.
Please note: Your electrician should leave 4
meters of spare cable leading from the isolator.
Our technicians are NOT qualied to connect
this cable to the inside of the Hot Tub.
Our delivery team will NOT hardwire your hot
tub to the mains supply. We advise you seek
a professional electrician to be present on the
delivery day.
Secon 3
ELECTRICAL REQUIREMENTS
*No extension leads.
*Can not have cable length longer than 3 meters.

12 13
Access + Delivery
Prior to delivery you must check that you
have the relevant access for your spa. This
informaon can be found in the product
specicaon in Secon 1.
Please consider the following when checking
your access
• Vehicle access for 3.5 tonne van
• The route the spa will need to take
• Any obstrucons, such as electricity boxes,
overhanging trees, gates, steps up or down.
If access is not possible than a crane will be
required, this may require redelivery. Redelivery
and crane will incur addional costs.
Hiab Cranes organized by us will include
1 hour labour for the crane company. Any
addional me required be changeable to the
customer.
If you are unsure and have any queries
regarding your access, we will be happy to
assist by reviewing photo’s/videos sent by you.
Site visits may incur an addional charge.
For any support on this maer please contact
our oce on 01246 559071.
Oce opening hours are…
Mon-Fri 9am-5pm
Saturday 9am-2pm
Alternavely please email us on
[email protected]o.uk
Fill It Up
1. Place a garden hose into the lter area
(Let your hose run for 5 mins before
pung into the spa to clear out any
stagnant water in the hose before pung
it into the hot tub.) Also, it’s a good idea
to use a hose-ended lter/water soner,
this will ll your spa from the pumps and
pipework rst to prevent any airlocks in
the system. Also, it’s a good idea to use a
hose-end lter/water soener will make
balancing water easier and to reduce the
amount of impuries that can contaminate
your water. At this point your hot tub
should be turned o at the isolator.
2. Fill water to recommended water level as
indicated by the minimum water level in
your hot tub. Low water levels can cause
damage to the pump and heater element
so is good pracce to top up your spa on
a weekly basis. If there is no water level
indicator, you should t your hot tub to 1
inch above the top of the back jets
3. Remove side panel and check for any
leaks around the plumbing. It is not
unusual for ngs to come lose during
shipment. If you do detect any small leaks,
you’ll want to hand-ghten them right
away. (Using a wrench can easily crack the
nut and cause the leak to worsen).
Power up the Spa
Aer checking all the ngs are ght and
are sure no leaks are occurring, you can
re-t the side panel and turn the power on
at the isolator point. Read Secon 7 on how
to operate your new spa controls and how to
turn on the hot tub.
Hot tubs can take approximately 12 – 24
hours to rise to temperature. Heat me
depends on spa size, voltage and other factors
such as outside temperature. Plug & Play hot
tubs take longer to heat than 32AMP.
Balance Your Water
Test and balance your hot tub water before
you introduce any sanizers. It is important
to balance prior to adding sanizers to avoid
unwanted problems such as cloudiness,
discoloraon or foul smelling water. Also,
keeping your water balanced is crucial
to promote long equipment life, and
healthy, clean, clear spa water. Poor water
management which results in components
of your spa degrading/failing can invalidate
your warranty.
More informaon on treang your water can
be found in Secon 8.
The control panel operaon (Secon 7) is lled with valuable informaon to
give you an idea of how your spa works and how to prevent any mishaps or
damage to your new hot tub before you get to use it.
Secon 4 Secon 5
DELIVERY OF YOUR SPA CHECKLIST BEFORE USING YOUR SPA

14 15

16 17
CONTROL PANEL OPERATIONS TP600
JETS AUX LIGHTHEAT
Secon 6

18 19
Daily: It is possible to select how many
ltraon cycles a day you want to your hot tub
to perform. We advise to set your ltraon
seng to run twice per day, for at least an
hour each me.
Weekly: It is good pracce to test your
water a couple of mes a week, then adjust
alkalinity, pH, sanizer, and calcium hardness
as required to bring the levels back in line
with the ‘okay’ range on your test strip pack.
If you’ve added sanizer during the week, you
may not need to add a weekly dose, so always
be sure to test before adding anything.
Every Three Months: It is advised to drain
your hot tub every three months and rell
with fresh water. Before you drain your hot
tub, add some hot tub ush to your hot tub
and let this circulate through the lines and
jets, this will eliminate any build up of bacteria
and prevent biolm.
Aer the bacteria in your lines is dead and
circulang, completely drain the dirty water
out of your spa. Rinse with clean water then
drain. Clean your hot tub, wash or replace
your lter cartridges, then rell your spa with
fresh water (Let your hose run for 5 mins
before pung into the spa to clear out any
stagnant water in the hose before pung it
into the hot tub). Consider using a hose lter/
water soener to prevent metals and other
contaminants from entering your spa in the
rst place.
Aer you rell your hot tub, balance the
water chemistry and use a shock treatment
to rid of any non-organic compounds that
have entered via the hose pipe. Be sure to
test the water one last me before stepping
into it the rst me. This will ensure your
spa contains the correct amount of sanizer
to destroy contaminants quickly.
Draining Your Spa
Approximately every 3 months it is
recommended to replace your water, the
frequency of which you replace your spa
water depends on regularity of use, care taken
in maintaining the water quality etc.
It will be apparent when your water is
ready for a change when you can no longer
control sud, scum and cloudiness of the
water even though the key water balance
measurements are all within the proper
parameters. Another alternave is to use
a submersible pump, this will allow you to
drain your hot tub much quicker.
NOTE: Always power o the spa before draining
it. Do not power on unl the spa has been
lled to the water level line.
Even though the spa is empty do not allow it
to sit in direct sunlight and always return the
spa cover.
If you intend to drain to shut down for winter,
please follow the steps in Secon 10.
Your drain valve will look something like this.
To operate, unscrew the center secon and
screw in the drain valve adapter that arrived
with your hot tub. The acon of screwing in
the drain valve adapter releases the water ow.
You may wish to aach a hose to the adapter
to run the water away.
Filter Care
Cleaning your hot tub lter is a vital part of
hot tub maintenance and plays a key role in
keeping your hot tub’s water safe and clean.
While cleaning your hot tub lter may seem
complex and cumbersome, it can actually be
quite simple. This will walk you through the
most common ways to keep your hot tub’s
lter spotless.
Tip 1: Filter Replacement
Regardless of how clean you keep your
spa’s lter, it is imperave that you replace
it at least every 6 – 9 months. In addion
to pung a severe strain on your hot tub’s
pump, worn-out lters are unable to properly
trap contaminants.
Tip 2: Basic Rinsing
Your spa’s lter should be given a thorough
rinsing once every 2 weeks. If you make
frequent use of your spa, however, you may
want to ulize this method of lter-cleaning
on a somewhat more frequent basis. This
method is very simple and can oen be
accomplished with nothing more than a
garden hose and an old tooth brush. Taking
care to remove every speck of dirt, use the
hose to give your lter a vigorous soaking and
use the tooth brush to carefully brush out in
between the lters paper pleats.
If the lter is parcularly dirty, all-natural
cleaning products can be used in conjuncon
with this method. It is also important to rinse
your lter o in this fashion whenever you
change the water in your spa, regardless of
how recently its last cleaning took place.
Tip 3: Cleaning Products
If your spa’s lter is exceponally dirty you
may want to consider incorporang the aid
of cleaning products. Filter/cartridge cleaner
has proven extremely eecve in laying waste
to caked-on dirt and calcium. Please follow
instrucons on packaging. Ensure you rinse
the lter thoroughly and leave to dry out
completely before placing back in your spa.
Tip 4: Mistakes to Avoid
When cleaning your hot tub lter, there are
several things you should avoid. First o, do
not aempt to clean your hot tub lter in a
washing machine, dish washer or pressure
washer as the immense water pressure can
damage the lter irreparably. Secondly, do not
try to clean your lter with bleach or laundry
detergents, as they will cause severe foaming
problems with your hot tub’s water, much like
other commercial cleaning products.
General Care
Vacuuming the spa: Debris from wind, trees
and spa users will occasionally accumulate on
the boom of your spa. Your spa’s ltraon
system will remove the smaller debris. Debris
that is too large or too heavy for the ltraon
system will have to be removed by the use of
a spa vacuum or net.
Headrest Care: Remove and clean the
headrest cushion as needed with soapy water
using a cloth or so sponge or brush.
Tip: always remove the pillows when adding
chemical treatments to the spa water. Replace
aer 30 minutes of running the chemicals
through the system with the spa cover o. This
will prolong their life and avoid reduce damage.
Maintaining the Cover: Use a household
hosepipe to gently rinse the spa cover of
any debris.
Using a so brush or sponge clean the cover
with soapy water or a hot tub cover detergent.
Do NOT use on the inside of the cover.
Tip: To prolong the life of the spa, handle
with care or use a hot tub cover lier and
clean regularly.
NOTE: Do not use solvents, abrasive products
or aggressive detergents e.g. containing
alcohol or bleach.
NEVER allow anyone to stand or sit on the
spa cover.
Panel Maintenance: Panels do not require
any special maintenance regime. To clean,
simply wipe down with a wet cloth. Never
spray water against the panels as directly
behind are electrical components.
Spa Shell Surface: To maintain the sheen of
your spa shell, it is crucial that you do not
use any abrasive cleaners. Only use specic
surface cleaners.
NOTE: Regardless of your chosen cleaning
method always ensure all the residue has been
removed from the surface as this could result in
your spa having to be drained and relled.
Secon 7
MAINTENANCE

20 21
Water Care Overview
Creang and scking to a water care plan for your
hot tub is the single most important thing you
can do to keep your spa—and all the people who
enjoy it—healthy.
Follow water care best pracces, and you’ll
prevent many potenal chemistry issues.
REMEMBER—More is not best when it comes
to sanizing!!
Addional notes:
1. Do not mix chemicals with each other before
adding them to the water. Add only one
chemical at a me
2. Never add concentrated liquid chemicals
directly to the water. Always dilute
chemicals in a large plasc bucket or pail
before adding them
3. When dilung chemicals, always add them to
the water. Never add water to the chemicals
4. Always dilute the chemical slowly and evenly
before adding into the water. Never add any
chemical, diluted or otherwise, into any
skimmer device
5. Always store chemicals according to the
manufacturer’s label direcons and keep them
out of reach of children
6. To maximize eciency of chemicals, change
the water in your spa every 3 months.
Water Chemistry explained
Moderaon is the key when adding any chemicals
to your hot tub. Everything you pour in aects
something else. They all have the potenal to
harm you or your spa and components if your
chemistry isn’t balanced.
So if you nd you have too much bromine or
chlorine in your hot tub, don’t worry! You can
avoid complicaons by taking the simple steps to
bring it down to healthy levels as soon as possible.
You’ll be back to enjoying your spa in no me.
Sanisers
A sanisers is absolutely essenal. It doesn’t
maer how clean your Hot Tub is, bacteria can sll
form. Our range of sanising products – such as
chlorine and bromine – will provide an excellent
defense against bacteria.
pH regulators
For your sanzer to work properly the pH
level of the hot tub water must be at the
recommended level. This can be adjusted by
using either a pH increaser or pH decreaser
depending on your tests.
Shock Treatment
Don’t panic, this isn’t quite as drasc as it sounds.
Shock Treatment is simply carried out to prevent
the eects of organic waste compounds and
involves periodically adding an increased amount
of chlorine or bromine to your hot tub; either
a weekly or fortnightly dose is recommended,
depending on how oen you use your hot Tub.
Clariers
A Clarier will help to keep your water crystal
clear and can be used on a weekly basis. It works
by ghng the parcles that slip through the
lter system.
We understand that the above may seem like
a daunng proposion, but it really isn’t. Your
health is important to us and by following these
simple procedures you will ensure that your Hot
Tub remains clean and sanized. If you have any
concerns please don’t hesitate to contact us.
DOSING YOUR SPA FOR THE FIRST TIME
Shock your water
Chlorine Shock
These types of shock are both oxidizers and
disinfectants as well. They should be used
periodically but not every single me you need to
give your hot tub a good shock as the chemicals
can be rather hard on your hot tub’s plumbing if
you’re not careful.
Chlorine based shock is best used when you rst
open your hot tub or when you change the water
and when you need to give it a good cleaning
aer a heavy bather load.
Non-Chlorine Shock
These shocks won’t disinfect the water, so if you
are worried about bacteria this isn’t the right one
to use. They are, however, great at oxidizing other
contaminants and cleaning up the water.
This type of shock is recommended for regular
use such as on a weekly basis to keep the water
in great shape while you are using your spa on a
fairly regular basis.
Why Shock Your Water
Remove organic compounds from the water:
If you use your hot tub oen or you have 3 or
4 bathers in there at once, the level of organic
compounds can spike quickly. Removing these
compounds is a must for clean water.
Kill bacteria: Chlorine and bromine based shock
compounds can easily kill bacteria growing
in the water so it is safe. However, if you use
other types of shock compounds, they will not
disinfect the water.
Remove bromamines or chloramines from the
hot tub: Adding shock once a week will help
break the bonds that form these contaminants
so they can easily be removed from the water.
Reacvate bromides in the spa: If your hot tub
uses bromine, adding shock once a week will
help acvate it to properly clean the water of
your hot tub.
How to Shock Your Water
1. Remove the hot tub cover to allow any gasses
to be released
2. Adjust the pH levels of your spa’s water to
between 7.2 and 7.8
3. Turn o the jets but leave the circulaon
pump running so the water is moving but is
not too agitated.
4. Measure the amount of shock you need for
the number of liters of water in your hot tub.
Check your shock’s label instrucons to nd
this informaon.
5. Add the shock to your hot tub carefully by
dosing this into the lter housing.
MAINTAINING YOUR SPA WATER
Use test strips to check the chemical and mineral
levels in your spa.
You should be checking and adjusng the
chemical levels in your spa 1-3 mes a week
depending on your usage. To do this you should
use appropriate test strips for the types of
chemicals you are using.
Chlorine—3 Way
Bromine—4 Way
Both Above, inc Calcium Hardness—5 Way
Put these strips in your spa for 15 seconds,
remove the stripe and hold
strip horizontally and view results.
PLEASE NOTE: Only add one chemical to your
spa at a me.
When adjusng hot tub chemical levels, add one
chemical to the water, and then wait a full two
hours before adding another chemical. This will
allow the chemicals to disperse naturally and will
help to maximize their eecveness. Waing
also minimizes the risk of a chemical reacons
between the addives that can cause problems.
- Keep your spa cover o for at least 15 minutes
aer you have added your chemicals.
- Use an old jug to extract spa water and use this
to pre-mix your granulated chemicals.
- Keep your spa water running when you add the
chemicals. Pour mixture into the spa lter housing.
- Pre-measure your chemicals before you add
them to your tub. NEVER pour chemical granules
directly into the spa. Make sure you are achieving
the right balance by measuring the chemicals
before adding them.
Check the pH levels
Add pH Plus (Increaser) or pH Minus (decreaser)
as necessary.
Your pH should stay between 7.2-7.8. If the pH is
o, rst work to stabilise the total alkalinity. Then
make sure you have added the proper amounts
of chlorine/bromine to your spa. And then if the
pH is sll o, add a pH balance product to your
spa pH level.Your pH levels may be adjusted if: the
saniser you use is not working well, your spa has
cloudy water, scales have developed on your lter,
or the water is causing skin and eye irritaons.
Secon 8
WATER CARE

22 23
Check total alkalinity.
Depending on the test reading, add Alkalinity,
Use Alkalinity Builder (to build up) or pH Minus
(to reduce) as needed. Use your test strips a
well-balanced spa should be between 80-120
PPM in Total Alkalinity.
If the total alkalinity goes above 120, you should
add pH minus (to reduce). If the test strip reads
below 80, add Alkalinity Builder (to build up).
Add the granules to your spa and then recheck
your alkalinity in around an hour. It is important to
maintain your alkalinity rst because it aects your
overall pH re.
Check for calcium hardness.
The best way to keep the calcium hardness in
your spa in check is to use so water in your spa.
If your spa has too much calcium hardness, it will
cause scales to form in your spa. You can use a
spa defender product to protect against these
scales. On the other hand, if your spa does not
have enough calcium hardness, the water will
start to draw minerals from other sources, like
the aluminum or iron in your equipment. In this
case, use a calcium booster to balance the calcium
hardness in your spa.
Calcium hardness should stay between 100-250
PPM. Using a water soener at the me of lling
the spa will help with this.
Use chlorine or bromine to sanise your hot tub.
Make sure to use test strips to maintain the
correct chemical levels.
Chlorine and Bromine can be purchased in
granular form or in 1-inch tablets. It is useful to
have both, as if you are using tablets and need
a boost it is easy to add a lile extra granules to
your spa water. Granular Chrlorine or Bromine is
usually dissolved in warm water and then applied
to the water, tablets are usually placed into a
oang dispenser which has a ow regulator to
change how quickly the tablets will dissolve, these
can be bought seperatley.
Ensure that you follow the dosage guidelines on
the relevant product packaging.
Do not over sanize your spa with Chlorine or
Bromine. Make sure you use the recommended
level of Chlorine or Bromine. Over dosing can
cause serious damage to the spas equipment
and cover.
If you nd you have over sanised your water
there are a few opons to helps reduce the levels.
The rst opon would simply be to do nothing,
leaving your spa will allow the sanizer levels to
naturally decrease. It would be advised you don’t
use the spa for a couple of days before you test
the water again. If you nd the sanizer level is
sll far too high, move on the next phase.
The next step would be to remove your hot tub
cover. This allows signicantly more water (and
by extension, chlorine or bromine) to evaporate.
It will lower chlorine or bromine levels in your hot
tub, plus decrease your water level so you can
move on to the next acon. The water level will
likely have dropped a couple of inches, and you
can simply top up your spa with fresh, clean water
which will dilute the chlorine/bromine levels. Let
it circulate, then test it again. But if you didn’t
lose much through evaporaon, and your spa is
sll nearly full, you’ll need to remove some water
so you can reduce the concentraon of sanizer
with fresh water. This will be enough to lower
the bromine or chlorine to the desired level in
most situaons. If your spa water has been in
your hot tub for two or three months, it’s about
me to drain and clean your hot tub anyway.
Also, if your water chemistry has been dicult
to balance aside from high sanizer levels, that’s
another indicaon that it’s me to drain and
clean. In either case, it makes more sense to start
with a full load of fresh water than trying to top
o old or highly unstable water.
Probable Cause: Soluons:
Cloudy Water • Dirty lters
• Excessive oils or organic maer
(moisturiser, fabric condioners,
make up
• Improper sanising
• Suspended parcles or
organic maer
• Overused or old water
• Clean lters with a lter Cleaner or replace lters
• Shock spa with saniser e.g. Non Chlorine Shock
(Bromine) or HTC Chlorine Shock
• Add saniser (Chlorine or Bromine)
• Adjust pH and/or alkalinity with pH/Alkalinity +Plus
or pH -Minus
• In severe cases use a spa ush soluon, Run jet
pumps, clean/replace lters, drain, clean and rell
the spa
Water Odour • Excessive organics
in water
• Improper sanisaon, not
enough Bromine/Chlorine in
water
• Low pH
• Shock spa with saniser
• Add sanizer
• Adjust pH with pH/Alkalinity +Plus to
recommended range
• In severe cases use a spa ush soluon, Run jet
pump and clean/replace lters, drain,
clean and rell the spa
Chlorine Odour • Chlorine level too high
• Low pH
• Shock spa with saniser
• Adjust pH with pH/Alkalinity +Plus to
recommended range
Musty Odour • Bacteria or algae growth • Shock spa with saniser
• If the problem is visible or persistent, drain, clean
and rell the spa
Organic Buildup/
Scum Ring
around Spa
• Build-up of oils and dirt • Wipe o scum with clean rag
• If severe, drain the spa, use Spa Surface cleaning to
protect the spa shell, and rell the spa
Foaming Water • Build-up of oils and dirt • Add spa Foam Away product
• In severe cases use a spa ush soluon, Run jet
pump and clean/replace lters, drain, clean and rell
the spa
Algae Growth • High pH
• Low saniser level
• Shock spa with saniser.
• Adjust pH with pH/Alkalinity -Minus to
recommended range
• Shock spa with saniser, and maintain saniser level
Eye Irritaon • Low pH
• Low saniser level
• Adjust pH with pH/Alkalinity +Plus
• Shock spa with saniser, and maintain saniser level
Skin Irritaon/Rash • Unsanitary water
• Free chlorine level above 5 ppm
• Shock spa with saniser and maintain saniser level
• Allow free chlorine level to drop below 5 ppm before
spa use
Stains • Total alkalinity and/or
pH too low
• High iron or copper in
source water
• Adjust total alkalinity and/or pH with pH/Alkalinity
+Plus
• Use Spa Stain & Scale to inhibit metals
Scale • Total alkalinity and/or
pH too high
• High calcium content in water
• Adjust total alkalinity and pH with pH/Alkalinity
–Minus
• If scale requires removal, drain the spa, clean spa
shell with Spa Surface Cleaner, and rell the spa
• Add Stain & Scale and balance the water using pH/
Alkalinity +Plus or pH –Minus
• It is advised to use Test Strips showing Water
Hardness

24 25
Less than 7 days…
For shorter stays away from the house, there are
a number of water treatment opons available
dependent on the duraon of your absence from
the house that will ensure that your hot tub water
and equipment stays healthy and balanced, and
ready for when you return.
Here’s a 6 step rundown of what to do before
departure:
1. Test and balance the alkalinity and hardness
level of your water
2. Clean your lter thoroughly or just replace it
with a clean one while you’re away
3. Add an appropriate amount of sanizer to a
oang dispenser - Shock your water with
sanizer before you leave
4. Secure hot tub cover
5. If you wish, you can drop the temperature to
save energy and money.
6. Do not turn o the power to your hot tub.
More than 7 days…
For longer holidays of over 7 days, it’s extremely
important that you take the me to prepare your
hot tub correctly.
1. Test and balance the alkalinity and hardness
level of your water
2. Clean your lter thoroughly or just replace it
with a clean one while you’re away
3. Add an appropriate amount of sanizing
tablets to a oang dispenser. If you can, ask
a neighbor to come by every few days to add
in a few appropriate chemicals
4. Shock your water with sanizer before
you leave
5. Add water clarier
6. Secure hot tub cover
7. If you wish, you can drop the temperature
to save energy and money or it is possible to
place your spa in sleep mode. Please refer to
the control panel operaons for instrucons
of how to do this
8. Use a Hot Tub Protecon Bag. This will also
help cut down electricity cost and protect
the external sides of your spa. Available to
purchase separately
If you do not intend on using your spa
throughout winter it is important you prepare
your spa for winter
PLEASE NOTE: If any water is le in your hot
tub, it can freeze and cause issues when re-
commissioning your hot tub aer winter.
What you will need: Hot tub ush
1. Drain valve (provided with the spa from new)
or submersible Pump
2. Wet and Dry Vacuum
3. Filter Cleaner
4. Hot Tub Surface Cleaner
5. Hot Tub Cover cleaner
Step by Step….
1. Remove the lters
2. Put the correct dosage of hot tub ush
in spa and circulate with all jets on for 30
minutes. Switch o at your main power
supply. Ensure there is absolutely no power
geng to your hot tub
3. Drain the water. Using a submersible pump
or the drain plug, begin draining your hot tub
completely. If you decide to use a sub pump,
make sure when you’re nished to remove
the drain plug from your hot tub anyway to
drain of as much of the water as possible
4. If you use the drain plug the hot tub will allow
you to aach a garden hose to it. A sub pump
is recommended instead of the drain because
the pump works much faster
5. Check to see if your hot tub has an air blower.
If it does, then you should get the remaining
water out of it. To do this, turn o the heater
– this will prevent the heater from being
damaged when you turn the hot tub electric
back on (the heater element should never run
without water)
6. Put the cover back on the hot tub and turn on
the electric – this will run the air blower. Let it
run for about 30 seconds, then shut the power
o to your hot tub. It would also be a good
idea to completely unplug the hot tub if it’s not
hard-wired
7. Take the cover o your tub. At this me, it’s a
good idea to clean them with lter cartridge
cleaner and store in a dry place
8. Use a wet and dry vacuum to make sure that
the lter housing has no water in it
9. Open up the cabinet to your hot tub and
locate the pump or pumps. If there are unions
that aached the PVC pipe to the pump(s),
loosen them. Remove all the drain plugs from
the pump(s) as well. This will allow water to
drain from your pipes if condensaon builds up
inside. Make sure to keep the drain plugs in a
safe place that you’ll remember(place them in a
sandwich bag and sellotape to the pump)
10. Clear out the pipework. Take a wet and dry
vacuum and turn the seng to blow, or
whatever will force air out instead of sucon.
11. 11.Get in your empty hot tub and place the
wet and dry vacuum hose up to all your jets.
Work your way around the enre hot tub
unl you’ve blown out every single jet. To be
thorough, repeat this process
12. Now that you’ve blown out the pipework,
you noce water in the tub. Make sure you
get all the water out of the tub by using a
submersible pump, wet and dry vacuum, or a
sponge. Ensure the spa is completely dry
13. Now that you have an empty hot tub, it is
recommended you clean the shell thoroughly
with a hot tub surface cleaner. If the cleaner
you use requires you to rinse with water,
please ensure you remove that water
completely.
14. 14.Deep clean the cover by using a hot tub
cover cleaner on both the outside and inside
15. 15.It’s important that you secure the cover to
your hot tub by using the straps. If your hot
tub cover will lock to your tub, then do so
16. As an extra precauon you could purchase a
Hot Tub Protecon Bag.
Secon 9
PREPARE YOUR SPA FOR A HOLIDAY
Secon 10
SPA WINTERISATION

26 27
It is important to service your spa, without regular care and maintenance, parts
such as the heater, pumps and pipe-work will eventually develop a build-up
of dirt and debris commonly referred to as bio-lm, this contains parasites,
viruses, bacteria and mould – all of which are extremely dicult to remove.
Draining and re-lling your spa alone will not tackle the build up of contaminants within the pipe work.
Having your hot tub serviced annually will dramacally help towards keeping your spa in a hygienic
state whilst maintaining the key components through the roune safety and diagnoscs test. Not
servicing your hot tub may result in your warranty being void. Please contact your local Superior Spas
dealer to arrange your service.
Secon 11
SERVICING
Your hot tub comes with a warranty to cover you in case of any breakdowns or
damaged parts. Details of your warranty are available from the Superior Spa’s
dealer you purchased your spa from.
In such a case where you need to log a warranty claim, please visit superiorwarranty.co.uk
where you will be asked to create an account and log your claim. ALL claims must be processed
via the online system before we can proceed.
Secon 12
WARRANTY
HOT TUB TROUBLESHOOTING
The Problem The Likely Cause(s) Troubleshoong Soluons Do you need to call a
professional technician?
The spa is
inoperave
• Power failure
• The breaker has
tripped
• Heater’s high-limit
thermostat has tripped
• Spa lock is acvated
• Check for problems with
your power source
• Reset the breaker
• Disconnect the power for
30 seconds to reset the
thermostat; then check
for clogged lters
• Deacvate the spa lock
• Contact an electrician
if your power source is
inoperave
• Call for your electrician
if the breaker won’t
reset
• •Call for spa service
if the high-limit
thermostat has tripped
Spa won’t heat,
even while the jets
and lights operate
• Air lock was created
aer lling the spa
• Blocked lters
• Failed air circulaon
pump or heater
• Remove air locks by
loosening pump and/or
heater unions
• Check for blocked lters,
try removing lter and see
if spa heats okay
• Check for water
movement
• Call for spa service if the
heater not working
• Call for spa service if
the circulaon pump
has failed
Jet operaon is
weak or surging
• Spa water level is
too low
• Filters are clogged
• Air control lever
is closed
• Add water to the spa
• Clean the lters
• Open the air control lever
• Turn individual jets if
not working
• Reach out to your
dealer if you have
further quesons about
opmal jet performance
and maintenance
Light is inoperave • Spa lock is acvated
• Light wiring or assem-
bly is faulty
• Deacvate the spa lock
• Replace the light assembly
• Call for spa service if
you are unsure of how
to replace your light
assembly
Flo, Htr dry, Dr,
Dy displayed
• Filters may be blocked
• Circulaon pump may
have failed
• Check and replace/clean
lters if needed
• Id the water in the
spa moving
• Call for service on no
water movement
Remote responds
intermiently
within the 30-foot
range
• An outside source
is interfering with
the signal
• Change the channel on
the remote by pressing
the Lights buon on
the dock unit unl the
buons ash and you see
a change channel screen
on the remote; press UP
or DOWN to adjust the
channel, and OK to set it
• Reach out to your
dealer with further
quesons about
operang your control
panel and remote
Touchscreen
connues to read
“Searching for spa”
on a black screen
• Remote is not paired
with the control panel
• Press the Jets buon on
the dock unit unl the
buons ash; press and
hold on the screen unl
Pairing Yes/No displays;
press Yes to pair
• Contact your dealer
for technical support
if problems with your
control panel or
remote connue

28
Superior Spas ltd
Unit 6, Staon Rd, Brimington,
Chestereld S43 1JU
t. [phone]
e. [email protected]o.uk
w. superiorspas.co.uk