Platinum Butlers Bell Kit Owner's manual

The pulley system inside the house
Step 1:
By now the cord should be attached to the top of the black rod and have been passed
through the hole that was drilled in the wall for the cord. The inside wall plate (B) will hide
the hole for the cord on the inside of the house. Attach a pulley (1xA) using one of the
big srews (1xF). The screw should be at the back of the plate and the pulley on the front. The
cord comes through the silver hole then runs around the pulley. The inside wall plate (B)
can be positioned, so that when the cord comes through the wall it can go in all directions.
The other pulleys in the hardware pack allow you to manouvre the cord around the walls to
the Butlers Bell.
Warning: We advise that you use as little length of cord as possible, and as few pulleys
as possible. If a lot of cord is used the tension on the inner spring is lost in the cord.
Mounting the Butlers Bell
Step 2:
Place the wall mounted stem (I) up against the wall. Depending on if your cord is
coming from the left or the right of the butlers bell.
CORD COMING FROM THE LEFT:
The brass arm needs to be past vertical with the top pointing in a north easterly direction (fig.1).
This is done by making sure that the inner spring is pointng down, facing south west (fig.2).
When the cord is attached to the brass arm it will pullback the arm to a vertical position causing
tension on the inner spring.
CORD COMING FROM THE RIGHT:
The brass arm needs to be past vertical with the top pointing in a north westerly direction.
This is done by making sure that the inner spring is piontng down, facing south east (fig.3).
When the cord is attached to the brass arm it will pullback the arm to a vertical position causing
tension on the inner spring.
Fig.1
Fig.2 Fig.3
Brass arm
Step 3:
When you have found the right postion, you can begin to mark out the holes in order to secure
the wall mounted stem (I). Once the holes are marked and drilled with the appropriate 6mm drill bit, insert
3 wall plugs (3 x E) and then fix the wall mounted stem to the wall using 3 screws (3xH).
Step 4:
Once the wall mounted spindle (I) is in place, replace the inner spring in your chosen direction (ref step 2).

Step 4:
After the inner spring is fitted. take the bell (L) and place on the wall mounted spindle (I). Making sure
that when the brass arm is in its vertical position you can feel the tension on the inner spring
Step 5:
Screw the rosette (K) onto the wall mounted stem (I) so that the components stay in place.
Mounting the Butlers Bell (cont):
Step 6:
Now the butlers bell is mounted in position on the wall, the cord from the wall plate
pulley (B) needs to find its way to the bell. Sometimes this is very simple. For example,
If the inside wall plate (B) is at the right height for your butlers bell then the cord can
travel straight to the butlers bell. If the bell is below or above the wall plate then the angle
bracket has to be used. The wall plate sends the cord vertically up or down. The angle
bracket then sends the cord along the wall to the bell. (see below diagrams for alternative
mounting examples.
Step 7:
To attach the cord to the bell arm, pull the bell arm to the left (if your cord is coming
from the left) or to the right (if your cord is coming from the right), so that the cord can
be attached when the brass arm is vertical. Ensuring that the cord is taut, feed the cord
through the eyes at the top of the arm and tie a knot, so that the correct tension is
available for operation.
Customer support
A: C H Byron
Byron House
34, Sherwood Rd
Aston Fields
Bromsgrove
B60 3DR
T: 0845 2301231
E: [email protected]
W: www.chbyron.com
Step 8:
Congratulations, now sit back
and enjoy a cup of tea on us!

Instructions for
installing your new
Butlers Bell
Kit.
Introduction:
Thank you for choosing this traditional Byron bell. We at Byron hope that this product will give you a long lasting service.
If You need further assistance please call us. 0845 2301231
Contents list:
1 x Traditional Butlers Bell
1 x Butlers Bell Hardware Pack
Bell pull installation:
Step 1:
Screw A & B together
Parts:
AB
C
D
E
F
G
Step 2:
Screw E onto the end of B.
Step 3: Slowly slide the rod through
D. The rod should go through the hole on the
plate first and then over the next support.
The bell pull:
A+B = Black iron rod
C = Top rod mounting
D = Bottom rod mounting
E = Handle
AB
Step 4: Whilst the rod is placed
in D. Slide the rod on and through C. The rod
should pass through the hole first then the
spring. Place item G above the spring and
screw onto the top of the iron rod (A).
BE
1st
2nd
1 x Black Bell Pull
1 x Black Pull Hardware Pack
YOU WILL NEED:
Flathead screwdriver
Electric drill
Appropriate 6mm drill bit
Appropriate 8mm drill bit
The hardware pack
F = Spring
G = Cord and
rod attachment
8 x black screws
(not shown)
8 x Wall plugs
(not shown)

Mounting your pull to the wall
Step 2
Once you have completed steps 1-4, the pull can be mounted to the wall.
Before securing the plates to the wall, locate the pull in a suitable position
so that when an 8mm hole is drilled to take the cord from the top of the ‘C’ plate, the
hole will be below the inside ceiling level in your hall, and away from any wall mounted
objects. Mark and drill the 8mm hole completely through your wall from the outside to the
inside. With the rod inserted (to ensure the plates are truly vertical) Mark and drill
the 4 screw holes on both ‘C’ and ‘D’ plates using the appropriate 6mm drill bit, taking care
to line up the previously drilled 8mm hole, with the hole at the top of the ‘C’ plate.
Remove the rod by unscrewing cap ‘G’ and secure the plates to the wall using the screws
and plugs provided.
Once the plates are fixed to the wall re-insert the black rod as in steps 3 & 4.
However before screwing on item ‘D’. Take the cord, tie a
knot in the one end. Then thread the cord
through item’G’ so that the knot is inside the barrell but
does not come through the hole. Then screw the the barrell back onto the rod,
thread the rest of the cord over the wheel and through the wall to the inside of
the house. This is best done using a straightened coathanger.
The Butlers Bell & Hardware Pack
AB
C
E
D
FG H
I
J
K
L
The hardware pack:
A- 3 x Pulley’s
B- 1 x Inside wall plate
C- 1 x Angle bracket
D- 1 x 9 metres of cord
E- 5 x Wall plugs
F- 2 x Large screws
G- 2 x Dowel screws
H- 5 x Brass screws
The Butlers bell:
I - 1 x Wall mounted stem
J - 1 x Inner spring
K - 1 x Rosette cap
L - 1 x Butlers bell
The hardware pack
The Butlers bell.
On opening the butlers bell kit (62500K), the Butlers bell will be assembled
together, as it should hang on the wall. Please keep the bell assembled in
order to continue.
Step 6