Plejd LED-10 User manual

LED-10
INSTALLATION MANUAL
0307.1.5
Mains electricity
230 V/50 Hz max 0,15 A
Standby power
0,3 W
Power factor (PF)
0,6
Uout
3-28 VDC
Cabel area
Connecons: 0,5-4,0 mm2
External operating temperature
-20 to +35 °C
Dimensions
46x46x18 mm
Protection
Over temperature soware
Short circuit protecon
Radio
2,4 GHz mesh
Bluetooth®
Radio range*
Up to 10m indoors.
*The Plejd mesh technology extends the range by
allowing the units to communicate with each other.
Further informaon can be found
in the Plejd app or at plejd.com
Compliant to standards
Plejd AB hereby declares that the product
complies with the norms and guidelines
pursuant to Direcve 2014/53/EU.
EN 61347-2-13
EN 301489-17
EN 300328
EC 1275/2008
Plejd AB
Kroksläs fabriker 27A
431 37 Mölndal
Sweden
Manufacturer | Plejd AB
Country of manufacture | Sweden
RISK OF INJURY TO PERSON OR PROPERTY
All work on the appliance must be
carried out by an authorised electrician.
Naonal laws and regulaons
must be followed.

Load (CC)
150 mA 1-4 W
350 mA 1-9 W
500 mA 1-10 W
700 mA 1-10 W
Install the product in the appliance box behind the push-
buon/box lid or use a bracket (MNT-01, not included) on
the wall or DIN rail. When installing in insulated or warm
environments or with several switches in the same box the
total power is reduced.
Note that the LED load is non-dimmable unl the LED-10
is congured. The load is set at low light level, 20 mA unl
the product is congured.
Constant current loads (CC) are connected in series.
Constant voltage loads (CV) are connected in parallel.
Use only for LED loads (DC).
tc marks the point with the highest temperature,
85°C, at a maximum of 35°C room temperature.
Load (CV)
12 V (DC) 0-8 W
24 V (DC) 0-10 W
Connect the product
1
NOTE! On installaon the product is non-dimmable.
Use the app to congure before use.
Control inputs 1 and 2 can be used for control using e.g.
- Push-buon (preset)
- Light switch
- Moon sensor
The inputs can also be used to wirelessly control one
or more products from Plejd. A double click can be used
to acvate lighng scenarios.
The sengs are easy to adjust in the app.
Control via control inputs 1 2
Support
Download the Plejd app via the App Store or Google Play.
Aer supplying power to the unit based on one of the
wiring diagrams, you can use the app to install the lighng.
This requires Internet connecvity and Bluetooth® on your
phone/tablet. You do not need any addional equipment
to get started.
With the help of the app, it’s simple to congure all
relevant sengs. The app can be used to schedule
the lighng using the astronomical clock or mer, control
lighng, and wirelessly sync control switches and scenarios.
Download the app and follow the instructions
Hand over the Plejd system
Hand over the Plejd system to your customer by wring
the system code on the included scker . You’ll nd the
code in the app once you have completed the installaon.
Place the scker in the distribuon box and give the
welcome folder to the customer.
2
3
In the event of any technical quesons, please contact
Plejd customer services.
E-mail: [email protected] | Phone: [phone]
HI!
N L 1 2
L
N
L
tc
LED
LED-10