PMV Mounts PMVSTANDEL User manual

pmvmounts.co.uk
Assembly instructions for PMV Electric High-Low Wall-Mount / Floor-Wall Stand
Up to 100Kgs Lift capacity / Universal fixing patterns up to 875mm x 400mm
Model No.
PMVSTANDEL
Factory No.
PMVSTANDEL
Box 1 contents Key
Read these instructions carefully before assembling this equipment.
Check the equipment has been supplied with all parts and fixtures prior to assembly.
Do not use if any parts are broken or appear to be damaged.
Assemble in a suitable and safe location away from sources of heat and moisture.
Only use fixings provided with these products - Secure all fixings securely with appropriately sized tools.
Do not attempt to alter or modify any part of the equipment or its attachments.
Two people will be required for assembly and for installation of the screen on to the equipment.
Do not position the equipment close to sources of heat or moisture.
If you experience any failures contact your reseller immediately - Do not attempt to self-repair.
Designed & Manufactured
in the United Kingdom
M8 x 20mm
Button head
Screen Fixing Kit
M5 x 20mm
Pozi-screw
M8 x 45mm
Pozi-screw
M6 x 20mm
Pozi-screw
M5 Washer
M6 Washer
M8 Washer
M4 x 5mm
Spacer
M5 x 5mm
Spacer
M6 x 6mm
Spacer
M8 x 6mm
Spacer
Also required;
M8 x 20mm
Pozi-screw X4
X4
X4
X4
X4
X4
X4
X4
X4
X4
X4
X4
M4 x 20mm
Pozi-screw
M
N
O
P
Q
R
S
T
U
V
W
X
Screen mounting arms X2
Screen mount X1
WM clamp X2
FW inner clamp X2
FW outer clamp X2
WM upper wall
mount X1
WM lower wall
mount X1
FW floor
mount X1
Control box X1
Male-to-male
motor cable X2
230v IEC power
cable X1
DPF1K Control pad
with steel clip X1
Motorised ram legs X2
Box 1 of 2 - 666mm X 300mm X 160mm @ 22Kg Box 2 of 2 - 970mm X 265mm X 130mm @ 17Kg
‘Head’ Screen
mounting brace X1
Box 2 contents
Wall-Mount - P2
Floor-Wall Mount - P3
Assembly Fixing Kit
M6 x 20mm
Button head
M5 x 6mm
Pozi-screw
M6 x 10mm
Button Head
M8 Washer
M8 Nut
M8 x 20mm
Button Head
M6 x 20mm
Pozi-screw
4mm Allen
Key
5mm Allen
Key
10 / 13mm
Spanner
Cable tie
X8
X8
X8
X8
X2
X4
X4
X2
X1
X1
X1
X4
M6 x 20mm
Countersunk
A
B
C
D
E
F
G
H
I
J
K
L

Technical helpline 0845 6037 212
Wall mount the lift.
4A - Mount the upper wall mount using all positions.
4B - Hang the assembled lift in place and us it to mark
up positions for lower bracket and then remove lift.
4C - Drill/prepare fixing points for lower bracket.
4D - Re-fit lift to upper bracket and secure in place, secure
fixing in to lower bracket to secure in full.
4E - Once in position tighten x2 nuts behind the upper wall
mount on both sides of the lift.
5mm Clearance
Bx8
2A
4A x12
3A
3B
3C
4C x12
4B/4D
4E
2B 2C 2D
Two person lift minimum
!
Wall-mount assembly instructions: 2
Cx4 Dx4
Ex2
Rear of ram-leg
Top of ram-leg
Rear of wall mount
Ax8
1Secure ram-legs to bottom wall bracket.
Note - Ensure ram-legs are orientated the same with the visible brackets at the rear. 22A - Assemble washers and nuts on to x2 clamps 2B - Leave 5mm clearance
2C - Insert leg clamps in to ram-legs
2D - Insert safety fixing to secure clamps to the ram-legs
3Mount and secure the ‘Head’
3A - Thread both ram-leg cables through the corresponding holes in the base of the ‘Head’
3B - Lower ‘Head’ in to position
3C - Secure to ram-legs, tighten up fixings in a diagonal pattern 4

Technical helpline 0845 6037 212
Fx4
Two person lift minimum
!
Floor-wall stand assembly instructions: 3
Rear of ram-leg
Top of ram-leg
Ax8
1Secure ram-legs to bottom wall bracket.
Note - Ensure ram-legs are orientated the same with the visible brackets at the rear. 2Insert ram-leg inner and outer clamps.
2A - Insert inner clamp in to the corresponding brackets on rear of ram-legs
2B - Position outer clamp over the inner and secure with x4 fixings
Note - Do not fully tighten fixings at this stage.
3A
Bx8
3B
3C
3Mount and secure the ‘Head’
3A - Thread both ram-leg cables through the corresponding holes in the base of the ‘Head’
3B - Lower ‘Head’ in to position
3C - Secure to ram-legs, tighten up fixings in a diagonal pattern
Secure the lift in place.
4A - Position the lift in the chosen location and use it to mark the fixing points in the floor and wall.
4B - Remove lift and prepare/drill all four wall positions and all six floor positions.
4C - Re-position lift and secure in place
4D - Tighten ram-leg inner and outer clamps together.
4
4C x4
4C x6

CBD6 Power Cable
DPF1K Control Pad
with steel clip hanger
Male-to-Male
Motor Cable
Male-to-Male
Motor Cable
CBD6 Controller
(Controller can be cable-tied to the inside of the
tray once install is complete and working in full)
Recess for Power Cable
To 230V Mains Supply
Wiring Diagram
WD Note2: Cable lengths not shown to scale.
WD Note3: Positioning shown as suggestion only.
WD Note4: After this step CBD6 Controller and wiring not shown in diagrams.
WD Note5: Cable ties provided to secure control box and wiring to the head if required.
WD Note1: Wiring the same for both wall mount and floor-stand assemblies.
FRONT
4
Cut-out
for control
pad
Cut-out
for control
pad
Technical helpline 0845 6037 212

5Secure Mounting bracket in place.
- Method the same for Wall-Mount and Floor-Wall Mount
Screen Fixing Kit
M5 Washer
M6 Washer
M8 Washer
X4
X4
X4
R
S
T
M4 x 5mm
Spacer
M5 x 5mm
Spacer
M6 x 6mm
Spacer
M8 x 6mm
Spacer
X4
X4
X4
X4
U
V
W
X
M5 x 20mm
Pozi-screw
M8 x 45mm
Pozi-screw
M6 x 20mm
Pozi-screw
M8 x 20mm
Pozi-screw X4
X4
X4
X4
X4
M4 x 20mm
Pozi-screw
M
N
O
P
Q
U-Xx4 R-Tx4
M-Qx4
If required
Suitable for up to 600mm tall VESA patterns
6Secure arms to screen.
Secure arms to VESA pattern using suitable fixings for that screen.
Gx4
Cx4
Dx4
Technical helpline 0845 6037 212
5

Two person lift minimum
!
7.2
8Operation.
Use control pad to raise or lower the rams.
If you experience any issues use the technical
helpline number at the bottom of this sheet
for advice.
CAUTION! ALWAYS CHECK SURROUNDINGS
BEFORE OPERATING THE LIFT
7Mount screen on to lift unit.
- Method the same for Wall-Mount and Floor-Wall Mount
7.1 - Lift screen, two persons minimum.
7.2 - Secure in place with safety fixings.
7.1
Technical helpline 0845 6037 212
Hx2
6