Pneumatrol E4518C Series User manual

Part codes E4518C****
E4580C****
E4519C****
E4590C****
Solenoid / Spring, Internally Piloted
Solenoid / Spring, Externally Piloted
Solenoid / Solenoid, Internally Piloted
Solenoid / Solenoid, Externally Piloted
Installation
The valve body is machined with three mounting holes to the dimensions shown below. This enables the user to
mount the valve to a bracket or other suitable location.
Air supply requirements
Filtration & Lubrication
The supply air shall be clean, dry and free from water, moisture, foreign parts and debris. It is recommended that a
<40µ filter/regulator be installed as close to the valve as possible to ensure proper supply air quality. The air supply
can be either lubricated or non-lubricated. In the case of lubricated air being used, the recommended oil types are
ISO and UNI FD22 (Energol HPL ~ Spinesso ~ Mobil DTE ~ Telles Oil).
Connections
Pneumatic Connections
All valve ports are tapped for G1/2 or 1/2”NPT male connectors. The mains air connection is clearly
marked with a number 1. The two outlet ports are marked with numbers 2 and 4, and the two exhaust ports
are marked with numbers 3 and 5. (See pneumatic symbols at top of page.)
Note that if ports are tapped NPT then the body will be stamped with ‘NPT’to identify this variation.
Electrical Connections
For electrical connection details and information please refer to the back of this sheet.
Air Pressure Range Table
Sheet Ref. E45C
Installation and Maintenance - Product E45, ‘Cnomo’ Series
Electrical Connections
Electrical connections vary depending on the coil type fitted to the valve. The principal alternatives are either Plug and Sock et
or Conduit Entry.
Electrical connections are made to
terminals 1, 2 and earth if necessary.
When a surge suppression diode has
been fitted ensure that terminal 1 is
positive and terminal 2 is negative.
Push out connection
block from housing
and insert cable
through gland.
Top view without
Surge suppression diode.
Top view with
Surge suppression diode.
Plug and Socket Coils Conduit Entry Coils
(terminal box coils)
Remove cover plate
to allow access to
terminal block and
insert cable through
gland and bush.
Electrical connections are made to the
two terminals and earth if necessary.
When a surge suppression diode has
been fitted the terminals will be polarity
sensitive. Ensure correct connection.
Top view without
Surge suppression diode.
Top view with
Surge suppression diode.
Internal Pilot
Sol. / Spring
External Pilot
Sol. / Spring
Internal Pilot
Sol. / Sol.
External Pilot
Sol. / Sol.
Working Pressure (p.s.i.) 45 to 120 0 to 120 22 to 120 0 to 120
Working Pressure (Bar) 3 to 8 0 to 8 1.5 to 8 0 to 8
Min. Pilot Pressure (p.s.i.) N/A 45 N/A 22
Min. Pilot Pressure (bar)N/A 3 N/A 1.5
Issue No. 1

Spares Information - Product E45, ‘Cnomo’ Series
Item 8
Safe area coil assemblies Hazardous area coil assemblies
Coil type Voltage Part code Coil type Voltage Part code
EExia 24v DC E13AXCA00B
Terminal
Box
24v DC E13AXCB00B
EExd
24v DC E13AXCD00B
110v AC E13AXCB00T 110v AC E13AXCD00T
240v AC E13AXCB00U 240v AC E13AXCD00U
MC30
24v DC E13AXCK00B
EExm
24v DC E13AXC900B
110v AC E13AXCK00T 110v AC E13AXC900T
240v AC E13AXCK00U 240v AC E13AXC900U
Plug
&
Socket
24v DC E13AXCP00B
ExN
24v DC E13AXCN00B
110v AC E13AXCP00T 110v AC E13AXCN00T
240v AC E13AXCP00U 240v AC E13AXCN00U
Spares parts kit Consisting of Item Quantity
VSK501 Spring 1 1
Seal* 2 8
Blanking Disc* 3 2
Seal 4 6
Cup Seal 5 2
Seal 6 2
Note 1: Not all parts are required for each individual valve.
Note 2:* Item 2 is used for internally piloted valves.
Item 3 is used for externally piloted valves.