Polanik T-12268-D User manual

Technical specification
Assembly manual
Double front pole vault landing area
T-12268-D
File: 2014-07-21
Product support
Paweł Ciechanowski
p.ciechano[email protected]

echnical specification/Assembly manual -12268-D 2/10
Thank you for choosing P LANIK landing area.
Safe assembly and use
•ATTENTI N! VACCUM PACKED PR DUCT – UNPACK IMMEDIATELY AFTER DELIVERY
•Before you start to assemble and use the landing area please read this manual carefully and store the
manual in a safe place for further reference. Polanik Sp. z o. o. shall not be liable for any cage damages
which are the result of the failure to follow this manual.
•Unauthorized copying of this manual, in whole or in part, is prohibited.
•he contents of this manual are subject to change without notice.
•Warning! he sports equipment produced by Polanik Sp. z o. o. is designed for athletics training and use in
sports competitions only. Please pay special attention when using the product, misuse of athletics
equipment can cause serious injury or in extreme cases even death. hat is why training and use during
sports events have to be always supervised by authorized sports personnel. In no event shall Polanik Sp. z o.
o. be liable for any special, incidental, indirect or consequential damages in connection with the purchase or
use of POLANIK products or costs over the original cost of the product.
•Specific warranty terms:
1) he use of the landing area outdoors requires a waterproof cover and a landing area platform for
proper insulation from the ground. Failure to follow the above restrictions results in the loss of the
warranty rights.
2) he top pad of the landing area is equipped with a spike resistant mesh fabric. he mesh fabric is
designed to protect the landing area against spikes used by jumpers. While landing and walking on the
top pad the spikes go through the mesh fabric and do not damage the surface. One must not shuffle
the spikes on the mesh fabric, because under high crosswise stress caused by moving the spikes
without lifting the feet, it may happen that the top pad will be torn. he damages of the top pad
caused by careless sliding the pikes on the top pad surface are excluded from the warranty and can be
removed in course of payable repair or replacement of the landing area elements.

echnical specification/Assembly manual -12268-D 3/10
Contents
Chapter Page
I. General description and use 3
II. echnical data 4
III. Packing and transport 7
IV. Preparing for first use 7
V. Assembly 8
VI. Operating 9
VII. Maintenance 9
VIII. Storing 9
IX. Declaration 10
I. General description and use
POLANIK double landing area -12268-D is the top quality sports equipment which is designed to secure
jumpers and absorb impact energy of a jumper’s landing after take off and flight in pole vault competition and
training.
double front
spike resistant mesh
fabric on both sides of
top element
advanced 3-layer
internal PUR
construction
outer covering – PVC
fabric made of
polyester with two
vinyl layers
stainless steel hooks and
D-rings
handles made of very
strong jacquard webbing
jacquard webbing belts
equipped with metal
self-locking buckles

echnical specification/Assembly manual -12268-D 4/10
II. Technical specification
Code T-12268-D
ype double front pole vault landing area, competition, type 11 of EN 12503-
2
Dimensions length/ width/ height [m] 12,2 / 6 / 0,8
Net weight [kg] 920 kg
Number of segments [pcs] 23
Spike resistant surface upper and bottom side of top segment fastened to landing area with
stainless steel hooks and D-rings
Segment outer covering PVC fabric made of polyester with two vinyl layers
Internal segment construction advanced 3-layer, air chamber, made of high quality PUR foam
Way of segment linking jacquard webbing belts equipped with metal self-locking buckles
Way of waterproof cover fastening metal hooks and D-rings
Handles handles made of very strong jacquard webbing, strong envelope
stitching

echnical specification/Assembly manual -12268-D 5/10
all dimensions [mm]

echnical specification/Assembly manual -12268-D 6/10

echnical specification/Assembly manual -12268-D 7/10
III. Packing and transport
he dimensions* of the vacuumed packed landing area segments:
Segment no. Description Weight
[kg]
length
[m] width [m] height [m]
01 pole vault box surrounding pad left 2,30 1,00 0,80
02 pole vault box surrounding pad right 2,30 1,00 0,80
03 Wedge panel 2,30 2,00 0,80
04 Wedge panel 2,30 2,00 0,80
05 Main segment 2,40 2,00 0,80
06 Main segment 2,40 2,00 0,80
07 Main segment 2,40 2,00 0,80
08 Main segment 2,40 2,00 0,80
09 Main segment 2,40 2,00 0,80
10 Main segment 2,40 2,00 0,80
11 Front panel 1,40 2,40 0,30
12 Front panel 1,40 2,40 0,30
13 Side panel 2,30 0,4 0,80
14 Side panel 2,30 0,4 0,80
23 op spike resistant pad 12,20 6,00 0,07
Volume [m
3
] 52,384
Gross weight [kg] 950
*Please note that the dimensions can differ from the above table in the range of +/- 7%.
IV. Preparing for first use
he landing area segments are vacuum packed only for transport. Please unpack them immediately after
delivery and leave them in a roofed place for few hours, so that they can return to their original shapes. Storing
vacuum packed landing area segments may cause permanent damages in their internal structures. When the
landing area elements return to their original dimensions, you can place them in a pole vault field. he field
surface should be even, smooth and without any obstacles. If you use the landing area outdoors, you should
also provide: a special waterproof cover P-12268-D to protect the landing area against unfavorable weather
conditions and a modular platform S -12,2x6 to insulate the landing area from the ground.

echnical specification/Assembly manual -12268-D 8/10
V. Assembly
o assemble the landing area please follow the below steps:
place the pole vault box surrounding pads (01 and 02) around the
pole vault box, so as the distance between the rear edge of the box
and the landing area pads (a) is 15 cm, make sure that all the
Velcro® pads adjoin properly, next attach wedge panels 03 and 04,
front panels 11 and 12, then side panels 13 and 14;
now the main segments 05, 06 and 07 should linked to the rest of
the segments using the jacquard webbing belts and self-locking
buckles located on the segment sides, do the same with the
segments 08, 09 and 10;
then place parts 01, 02, 11, 12, 13, 14 on the other side in the same
way as in the first step;
last step is to place the top pad 23 on the landing area and fasten it
to the segments using the snap hooks and D-rings, now the landing
area is ready for use.

echnical specification/Assembly manual -12268-D 9/10
VI. perating
Stepping on the landing area and practicing require special footwear designed for those purposes. reading
on the landing area in footwear with spikes is only allowed when the landing area is equipped with special
spike resistant surface. Stepping on the landing areas in hard footwear or in shoes with heels is strongly
prohibited. You must not put any tables, chairs, benches or any other objects whose unit pressure exceeds
1kg/1cm
2
on the landing area. If the landing area is moved from one place to another very often, it is
recommended that a landing area cart should be used.
VII. Maintenance
Due to the hygiene requirements it is recommended that the landing area should be cleaned regularly with
commonly available detergents. Before you start wiping the landing area, please try to clean a small spot on
its bottom side in order to check the reaction with the PVC fabric.
VIII. Storing
he landing area segments can be stored only in a horizontal position. hey cannot be bent or pressed by any
objects during storing. hat may deform the segments permanently. A storing facility should be clean and dry.
Minimum storing temperature is 5°C.
Even the best technical solutions cannot substitute for common sense. he usage of the product must take
place under the supervision of qualified coaches. he producer shall not be liable for any incidents caused by
the improper assembly or its misuse. he producer reserves the right to introduce without warning changes in
product constructions and colours.

echnical specification/Assembly manual -12268-D 10/10
IX. Declaration
1) No. 2012-06-19
2) Issuer’s name: POLANIK Sp. z o. o.
Issuer’s address: Zyczliwa 11, 97-300 Piotrkow ryb.
3) Object of declaration:
4) he object of declaration described above is in conformity with the requirements of the following documents :
Document No. itle Edition/Date of issue Position
PN-EN 12503-2 type 11 Sports mats – Part 2: Pole vault and high
jump mats, safety requirements April 2004 All above
Additional Information
5) Declaration for:
BUYER and USER
Signed for and in behalf of:
POLANIK.
2014-07-21 Piotrkow ryb.
(Date and place of issue)
Pawel Ciechanowski
Product Manager
6) ……………………………………… ……………………………………………………………………………
(Name, function) (Signature or equivalent authorized by the issuer)
Position Name Code
1 Competition pole vault landing area 12,2 x 6 x 0,8 [m] T-12268-D