Polanik T6-RC User manual

TECHNICAL SPECIFICATION
ASSEMBLY MANUAL
Race clock
T6-RC
File: 2014-07-29
PRODUCT SUPPORT
Pawel Ciechanowski
p.ciechanowski polanik.com

Technical specification / user manual T6-RC 2 / 5
ATTENTION!
The board s an electron c dev ce and t requ res careful handl ng!
CONTENTS
Chapter Page
I. General use 2
II. Technical specification 3
III. Assembly 4
IV. Operating 4
V. Declaration 5
I. General use
The race clock led display is designed to display running time during sports events or trainings.

Technical specification / user manual T6-RC 3 / 5
II. Techn cal spec f cat on
Power supply – 230V AC
Power consumption – 50VA
Display box dimensions – 1550x 340 x 100 [mm]
Frontal cover – solid polycarbonate
Display type – LED
Display colour – red
Digit height – 25 cm
Good visibility – 100 m
Maximum visibility – 125 m
Displayed time format – HH:MM:SS (standalone operation)
Displayed time format – HH:MM:SS (operation with chronometer)
Max view angle – 120°
Weight – 10 kg
Casing – aluminium, powder painted, outdoor use
Temperature range: from – 10°C to + 50°C
Set contains – display, tripod, handheld control keypad
START UP starts to count up time from the initial value
+
increases
hours/ minutes/ seconds when
setting the initial value
-
decreases
hours/ minutes/ seconds when setting the initial value
KASUJ/CLEAR clears the clock to 0
USTAW/SET starts setting the initial value
STOP stops the clock
START DOWN starts to count down time from the initial value

Technical specification / user manual T6-RC 4 / 5
III. Assembly
1. Set up the clock in a suitable place.
2. Connect the clock to power supply.
3. The clock tests led display units (all segments light up for about 2s). Then the clock shows time 0s. and it is
ready to use.
IV. Operat ng
1. Standalone operation
Operate the display with the handheld keypad:
a) press USTAW/SET to adjust first two digits (hours HH), while the digits are fleshing press + to set up their
initial value, then press USTAW/SET again to adjust next two digits (minutes MM), repeat the sequence to set
up last group (seconds SS),
b) press START to start measuring time from the initially adjusted value,
c) press STOP to stop measuring time,
2. Operation with chronometer
Preparation for use:
-connect the board with the chronometer using the included cable
-switch on the power of the board
-switch on the chronometer (see the instruction manual of the chronometer)
a) when the power is on the chronometer display shows the producer name and the version of the program, and then
the main menu is displayed:
T mekeep ng – measuring time
Sett ngs – options
OFF – switching off the chronometer
Clear races – clears the memory of the chronometer, recorded results and races are erased
b) use keys: up ˄ , down ˅, ENTER and numeric keys to operate the chronometer; press ESC to display the main menu,
c) the chronometer settings:
START-NO
STOP-NO
Arming – 0s
Resolution – 1/100sec
Rounding – IAAF rounded

Technical specification / user manual T6-RC 5 / 5
d) operation during a competition – measuring time is done in T mekeep ng, press ENTER and the chronometer is
ready to measure time, the board shows 0s,
e) press START to begin counting time, the board displays the running time, the chronometer prints the actual start
time, when the lane timekeepers press STOP the chronometer prints the actual finish time, and then the net time is
calculated.
V. Declarat on
1) No. 2014-07-29
2) Issuer’s name: POLANIK
Issuer’s address: Zyczliwa 11, 97-300 Piotrkow Tryb.
3) Object of declaration:
4) The object of declaration described above is in conformity with the requirements of the company production internal norms.
Additional Information
5) Declaration for:
Buyer/Distributor/User
Signed for and in behalf of:
POLANIK
2014-07-29 Piotrków Tryb.
(Date and place of issue)
6) Pawel Ciechanowski
Product Manager
…………………….………………….. ……………………………………………………………………………
(Name, function) (Signature or equivalent authorized by the issuer)
No. Description of goods Code
1 Race clock T6-RC