Polk Mono Atrium SUB100 User manual

opalk.
ATRIUM® SAT300
OUTDOOR SATELL:: F TE
ATRIUM® SUIB100
OUTDOOR SUBWOOFER.
Customer Service Hours of Operation: Monday-Friday 9AM-6PM EST [email protected]

ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
This product was designed and manufactured to meet strict quality and safety standards.
There are, however, some installation and operation precautions which you should be
particularly aware of.
Read
Instructions. All the safety and
operating instructions should be read before
the system is operated.
Retain Instructions. The safety and
operating instructions should be retained
for future reference.
Heed Warnings . All warnings on the
appliances and in the operating instructions
should be adhered to.
Follow Instructions. All operating and use
instructions should be followed.
Cleaning. Unplug the appliance from wall
outlet before cleaning . Do not use liquid
cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
Attachments. Do not use attachments not
recommended by the product manufacturer
as they may cause hazards.
Accessories. Do not place these appliances
on an unstable cart, stand, tripod, bracket,
or table. The audio/video products may
fall, causing serious injury to a child or
adult, and serious damage to the products.
Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the appliances.
Any mounting of the appliances should
follow the manufacturer's instructions,
and should use mounting accessories
recommended by the manufacturer.
Power Sources. This product should be
operated only from the type of power source
indicated on the marking labels. If you are
not sure of the type of power supply to your
home, consult your appliance dealer or local
power company.
Lightning. For added protection for this
audio/video product during a lightning
storm, or when it is left un-attended and
unused
for long periods of time, unplug
it from the wall outlet and disconnect the
antenna or cable system. This will prevent
damage to the product due to lightning and
power-line surges .
Object and Liquid Entry. Never push objects
of any kind into this product through
openings, as they may touch dangerous
voltage points or short out parts that could
result in a fire or electric shock .
Servicing . Do not attempt to service this
product yourself, as opening or removing
covers may expose you to dangerous
voltage or other hazards. Refer all servicing
to qualified service personnel.
Damage Requiring Service. Unplug this
product from wall outlets and refer servicing
to qualified service personnel under the
following conditions:
a. If liquid has been spilled, or objects have
fallen
into the product.
b. If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are covered
by the operating instructions, as an improper
adjustment of other controls may result in
damage and will often require extensive
work by a qualified technician to restore the
product to its normal operation.
c. If the product has been dropped or the
cabinet has been damaged.
d. When the product exhibits a distinct
change in performance - this indicates a
need for service.
Replacement Parts. When replacement parts
are required, be sure the service technician
has used replacement parts specified by
the manufacturer or that the parts have the
same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock or other hazards.
Safety Check. Upon completion of any
service or repairs to this product, ask the
service technician to perform safety checks
to determine that the products are in proper
operating condition.
Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: [phone])

SAFE LIMITS OF OPERATION
Polk Audio specifies the recommended
amplification range for each of its passive
(non-amplified) loudspeakers. Typically that
specification will be expressed as a range of
power such as 20-200 Watts (per channel).
It is important to understand what those
numbers mean when choosing a receiver or
amplifier for your Polk Audio loudspeakers.
The lower number indicates the lowest
continuous rated power that will yield
acceptable performance in a typical listening
environment. The higher number indicates
the highest per channel power that should
be used with your Polk Audio speakers.
That number should not be confused with
a "Power Handling" specification and it
does not imply that the speaker will safely
handle that full amount of power on a
long-term basis. We specify a wide range
of power ratings because not all electronics
manufacturers use the same method for
rating power. In fact, high quality lower-rated
amplifiers sound better and play louder than
low quality units with higher power rating.
Automobile horsepower is a good analogy.
Your
car probably has far more horsepower
than it needs for your daily commute and is
likely
capable of going well over 120mph
(190km/hr). Having that extra power is
good for on-ramp acceleration and danger
avoidance (like getting away from brain-
eating zombies) but that doesn't mean
that it is advisable to operate your car on
North American highways at full power and
maximum speed for an extended period
of time. Just ask your local state trooper if
you are in doubt. Similarly, we recommend
using amplifiers and receivers with rated
power above the power handling limits of
our speakers because having extra power
available for short term peaks is conducive
to better sound quality, maximum dynamic
range and effortless high volume output.
But we strongly urge you not to use the full
power of your amplifier or receiver for daily
listening.
Loudspeakers can be damaged when an
amplifier, regardless of its wattage, is made
to play at higher listening levels than its
power can clearly produce. Operation at
this level can result in very high levels of
audible distortion originating in the amplifier,
which can add a harsh, gritty sound to your
listening material. If you hear distortion -
turn the volume down or risk damaging your
speakers. You can damage just about any
speaker, regardless of power rating, if you
drive an amplifier to or beyond the point
of distortion.
PRODUCT DISPOSAL
Certain international, national and/or local
laws
and/or regulations may apply regarding
the disposal of this product. For further
detailed information,
please contact the
retailer where you
purchased this product
or the Polk Audio
Importer/ Distributor in
your country. A listing
of Polk Audio Importer/
Distributors can be found
on the Polk Audio website
www.polkaudio.com or by contacting Polk
Audio at:
5601
Metro Drive, Baltimore,
Maryland 21215, USA
Phone: [phone].
TECHNICAL ASSISTANCE OR SERVICE
If, after following the hookup directions, you
experience difficulty, please double-check
all wire connections. Should you isolate
the problem to the speaker, contact the
authorized Polk Audio dealer where you
made your purchase, or contact Polk Audio
Customer Service 800-377-7655 (M-F, 9am-
6pm EST, US & Canada only) or via email
[email protected]. Outside the US
& Canada, call [phone]. More
detailed information including audio how-
to articles, FAQs and online manuals are
available on our award-winning website:
www.polkaudio.com/home.
Customer Service Hours of Operation: Monday-Friday 9AM-6PM EST
polkcs@polkaudio . com

INVENTORY LIST
Important Note: If anything is missing or
damaged, or if your speaker fails to operate,
notify Polk Audio Customer Support
Services immediately at 800-377-7655.
Atrium SAT300 Satellite Carton Contents
(1) Atrium SAT300 satellite speaker
(1) Ground stake
(1) Security plate
(1) Pendant cap
(1) Rubber bumper
(1) Eyebolt
(2) Faston connectors
(1) Registration Card
(1) Mounting template
(1) #10 pan head screw
(2) #6 pan head screws
(1) Lock washer
(2) Wire nuts
(1) Atrium SAT300/SUB100 Owner's Manual
Atrium SUB100 Subwoofer Carton Contents
(1) Atrium SUBl00 Subwoofer
(1) Weatherproof aluminum grille
(1) Junction box
(4) Wire nuts
(1) Owner's Manual
Polk Audio Customer Service 800-377-7655 (Outside USA & Canada : [phone])

.
ATRIUM SAT300
PAINTING THE SAT300 LOUDSPEAKER
While the Atrium SAT300 has a color-
impregnated finish that enables it to blend
in with your landscaping and outdoor
furnishings, the cabinet is paintable. Should
you choose to paint your speakers, follow
these instructions:
Before you begin, you will need:
• A spray can of primer paint (Krylon
Sandable Spray Primer #1318).
• A
spray can of the outdoor paint of
your choice.
• A paperclip or thin blade (for removing
the paintable grille).
• Masking tape.
• Paint mask (not included) to cover
un-paintable parts.
PREPARING TO PAINT
1. Separate the parts of the speaker:
Remove the knob, clamp and bracket.
Remove the grille by carefully hooking it
with a bent paper clip or thin blade and
prying it gently away from the cabinet.
2. Carefully mask off the following:
• Driver
• Tweeter
• Terminals
• Threaded Insert
PAINTING THE CABINET, CLAMP, BRACKET
KNOB AND BRACKET
1. Apply two thin coats of primer to the
cabinet, clamp, knob and bracket.
2. When the primer is completely dry, apply
the finish color. Multiple coats may be
required for a consistent look.
3. When the paint is completely dry, remove
the masking material.
4. Try
to keep all handling of freshly painted
parts to a minimum.
PAINTING THE GRILLE
Note: Make sure the grille is removed and
remove the logo badge before painting.
1. Paint the Atrium SAT300 grille using a primer.
2. Using spray paint, spray two thin coats of
finish color. If you're using a compressor
and spray gun, use the finest, most diffuse
setting. Be careful not to fill the holes in the
grille with paint.
3. Paint the logo badge.
4. Replace the logo badge once the paint is
completely dry on the badge and the grille.
5. Carefully fit the grille into its recess so that
it is just resting on the cabinet. Go around
the speaker and push the grille into the
grille notch a little bit at a time. Be gentle;
the grille may be easily bent out of shape
by rough handling.
Customer Service Hours of Operation: Monday-Friday 9AM-6PM EST
[email protected]

I
ATRIUM SUB100
PAINTING THE SUB100 SUBWOOFER
While the Atrium SUB100 has a color-
impregnated finish that enables it to blend
in with your landscaping and outdoor
furnishings, the cabinet is paintable. Should
you choose to paint your speakers, follow
these instructions:
Before you begin, you will need :
• A
spray can of primer paint (Krylon
Sandable Spray Primer #1318).
• A
spray can of the outdoor paint of
your choice.
• Masking tape.
• Paint mask (not included) to cover
un-paintable parts.
PREPARING TO PAINT
Carefully mask off the following:
• driver
• eyebolt
• cable
PAINTING THE CABINET
1. Apply two thin coats of primer to
the cabinet.
2. When the primer is completely dry, apply
the finish color. Multiple coats may be
required for a consistent look.
3. When the paint is completely dry, remove
the masking material.
4. Try to keep all handling of freshly painted
parts to a minimum.
Customer Service Hours of Operation : Monday-Friday 9AM-6PM EST
[email protected]

MOUNTING THE ATRIUM SAT300
GROUND MOUNT
To mount the SAT300 into the ground
with a security plate, you will need the
following hardware:
• SAT300 speaker
• Ground stake
• Security plate
• Rubber bumper
• (1) #10 pan head screw (for security plate)
• (1) .25" split ring lock washer
• (2) #6 pan head screws (for speaker
assembly to the stake)
Max Depth -7.25"
Exploded View of SAT300
Cabinet
#6 Pan
Rubber
bumper
Ground
stake
Security plate
(Optional)
#10 Pan
head screw
Clamp
Knob
Bracket
--.:::::::~~~::::::_ .25" Split ring
lock washer
Ground Mounting Depth
Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: +l 410-358-3600)

I
Instructions
1. Attach stake to security plate using the
#10 pan head screw and .25" split ring
lock washer.
2.
Dig a hole to the diameter of the security
plate (6.5") and to a depth (max 7.25" /
min 2. 25") that will stabilize and secure
the speaker once the earth has been
tamped down around the plate.
3. Place the stake/security plate assembly
in the hole and cover with dirt, tamping
down the soil with your foot as you fill in
the hole.
4. Attach the Atrium SAT300 to the stake
using the rubber bumper and the #6 pan
head screws.
5. Loosen the knob to aim the speaker.
When the speaker is aimed properly,
tighten the knob.
Aiming the Speaker
Ground Mount Without Security Plate
If you choose to mount the SAT300
loudspeaker in the ground without the
security plate, be sure the ground is
compact enough to hold the speaker and
stake securely in the ground . Gently drive
the ground stake into the ground using a
rubber mallet and follow instructions from
step 4.
Customer Service Hours of Operation : Monday-Friday 9AM-6PM EST
[email protected]

PENDANT MOUNT
To pendant mount the SAT300, you will
need the following hardware:
• SAT300 Loudspeaker
• Eyebolt (with nut)
• (1) .25" split ring lock washer
• Two faston connectors
• Pendant cable (not included)
• Loudspeaker wire (not included)
• Pendant cap
Pendant
cable
Eyebolt ---.. ~
Nut
1
Lock washer -• ~
Penda_n_t_ _,..~
cap ~
Cabinet
Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: +l 410-358-3600)

I Instructions:
Note: A pendant cable (not included)
is required to hang the Atrium SAT300
loudspeaker from a ceiling or overhead
beam. Use a cable that meets or exceeds
the safety and/or building codes applicable
to the mounting situation. The speaker
weighs 3.5 lbs. on its own.
1. Determine how far down from your
ceiling or beam you want your
loudspeaker to hang.
2. Secure the pendant cable to the ceiling or
beam and run loudspeaker wire along the
pendant cable.
3.
Attach the supplied faston connectors to
the loudspeaker wires. ·
(Large = "+", Small = "-")
4. Expose the loudspeaker spade terminals
on the back of the cabinet by removing
the knob, clamp and bracket.
5. Disconnect the existing loudspeaker
wire from the spade terminals using
needle-nose pliers and remove the
bracket assembly.
6.
Thread the new speaker wire through the
wire hole in the pendant cap and connect
the wires to the loudspeaker spade
terminals, observing correct polarity.
7. Attach the pendant cap to the speaker
using the eyebolt, lock washer and nut.
8. Secure the pendant , cable to the eyebolt.
Caution: Secure mounting is required to
prevent personal injury or damage to
the speaker.
Customer Service Hours of Operation: Monday-Friday 9AM-6PM EST
polkcs@polkaudio . com

BRACKET MOUNT
For more solid mounting, screw the bracket
directly into a weight-bearing stud on the
mounting surface.
To
bracket mount the SAT300, you
will need the following hardware:
• SAT300 speaker
• Rubber bumper (optional)
• (2) #6 pan head screws
• SAT300 Mounting Template
Instructions
1. Determine where you want to mount
the speaker.
2. Hold the mounting template to the
mounting surface and mark the screw
hole locations with a pencil.
3. Use an 1/8" drill bit and drill the
mounting holes (if necessary).
NOTE: Use wall anchors if mounting
the speaker into drywall.
4. Loosen the knob on the back of the
speaker so it can swivel.
NOTE: The speaker bracket has a notch
for the speaker wires, which allows you
to run the speaker wires up the mounting
surface, or you may drill a hole in the
mounting surface and run the speaker
wires through the hole.
5. Place the rubber bumper underneath
the bracket (optional) .
6.
Hold the speaker to the mounting surface.
7. Attach the speaker assembly using the
supplied #6 pan head screws.
8. Once the loudspeaker has been adjusted
to the desired angle, tighten the knob on
the back of the loudspeaker to hold it
in place.
Mounting Template
WARNING: Aiming
the SAT300 to an angle
greater than 45 degrees to the horizontal
may result in water buildup inside the
grille that could cause damage to the
speaker, especially during cold weather
when freezing may occur.
Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: [phone])

MOUNTING THE ATRIUM SUB100
The SUBl00 can be located anywhere
you desire.
DECK MOUNT
1. Determine where you want to l.ocate
the subwoofer.
2. Measure the center-to-center distance
between the key-hole slots and install
two #10 mounting screws into the deck,
leaving .25" of the screws exposed above
the surface.
3. Place
the subwoofer onto the pan head
screws and rotate the SUBl00 clockwise
so that the keyhole slots lock down onto
the pan head screws.
GARDEN PLACEMENT
You may locate your Atrium SUBl00
anywhere you can run speaker wire. If you
place your subwoofer in a garden bed, upon
soft ground or mulch, we recommend you
place it on a paver or other hard surface.
This
will prevent mulch or dirt from building
up underneath the subwoofer, which must
remain clear for optimum performance and
to prevent damage to driver.
The
included grille can be attached to
prevent wildlife from taking residence under
your subwoofer (Part# AM3387-A).
Note: The SUBl00 has a built-in security
eyebolt that enables you to anchor it to
its location.
.25" ~ii
(.635cm) (,..... _ ___. ____ (_
Keyhole Slots
Security
Eyebolt
Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: +l 410-358-3600)

ATRIUM SAT300 & ATRIUM SUB100
HOOKUP DIRECTIONS:
Connect only two SAT300 Speakers
per stereo channel.
(Not sold in pairs.)
The
Atrium SAT300 and Atrium SUBl00
each come with 3 feet of CL3 speaker wire,
which is rated for underground burial. The
SAT300 has two conductors - one red that
is labeled "+" and one black that is labeled
"-". The SUBlO0 has four conductors (white,
green, red and black) because it has a dual
voice coil. Follow the correct polarity during
hookup to avoid performance issues and/or
damage to your amplifier.
A
standard configuration for outdoor
listening includes two SAT300 speakers
and a single SUBl00 subwoofer.
Amplifier
LEFT
RIGHT
#=== + SAT300 Left
......,_::_:_=_=_ =_ :!: SUBl00 Left (coil l)
~=== + SAT300 Right
-'!-+~:;::;::;::;:~ ::!: SUB100 Right (coil 2)
Connect one SAT300 speaker to the+/-
terminals of the amplifier's left output
channel (red wire to "+" and black wire to
"-"). Connect the other SAT300 speaker
to the+/- terminals of the amplifier's right
output channel. Next, connect the white
and green wires of the SUBl00 to the
amplifier's left output channel and connect
the red and black wires of the SUBl00 to
the amplifier's right output channel.
Amplifier SAT300 SAT300
SUBlOO
Output
#1 #2
+ RED
WHITE
LEFT
-
BLACK
GREEN
+ RED RED
RIGHT
-
BLACK BLACK
A standard configuration utilizes the left
and right outputs from separate amplifiers
to drive the SAT300's and the SUBl00.
+
SAT300 Left
LEFT
+
SUBl00 Right
RIGHT
+
SUBl00 Left (coil 1)
LEFT
RIGHT +
SUBl00 Right (coil 2)
Connect one SAT300 speaker to the
+/- terminals of the first amplifier's left
channel output and connect the other
SAT300 loudspeaker to the+/- terminals
of the first amplifier's right channel output.
Connect the white and green wires of
the SUBl00 to the second amplifier's left
channel and the red and black wires
to the second amplifier's right channel.
Customer Service Hours of Operation: Monday-Friday 9AM-6PM EST
[email protected]

Amplifier
SAT300 SAT300
SUBl00
Output
#1 #2
+ Red
Left
-
Black
Amp
#1
+ Red
Right
- Black
+
White
Left
-
Green
+ Red
Right
-
Black
You must always connect the left and right
channels
to achieve maximum output.
Observe positive ( +) and negative (-)
polarity. Reversing polarity of a dual voice
coil subwoofer will result in very
little bass
output and possibly damage the speaker
or amplifier.
All speaker connections should be
made with the provided wire nuts.
We recommend filling each wire nut
with a little silicone sealant to ensure a
weatherproof connection.
Any number of SAT300 loudspeakers can
be used in an installation. For applications
requiring more than two SAT300
loudspeakers, use a separate amplifier
channel for each additional pair of SAT300
loudspeakers. Do not use the A and B
channels
on your receiver to hook up two
pairs of SAT300 loudspeakers, as this
may overload and damage your receiver/
amplifier circuitry. If you need help with
wiring or connecting more than one pair
of SAT300 loudspeakers, please contact
tech support.
Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: [phone])

NOTE
You will need additional 2 conductor and 4 conductor Direct Burial Underground speaker
wire if you want to run the SAT300's farther than the 3 feet provided. For distances of 100
feet or less we recommend 14 AWG (Gauge) wire. For distances greater than 100 feet we
recommend 12 AWG (Gauge).
Connecting 2 SAT300 loudspeakers (Parallel hook up) to the Direct Burial IPX 7 Junction
box provided
The Atrium SAT300 and Atrium SUBl00
each come with 3 feet of CL3 speaker wire,
which is rated for underground burial. If
you wish to place the SAT300's or SUBlO0
farther than 3 feet from the supplied
Junction Box than you will need to use
additional speaker wire.
The SAT300 has two conductors-one red
that is labeled"+" and one black that is
labeled"-". The SUBl00 has four conductors
(white, green, red and black) because it has
a
dual voice coil. Follow the correct polarity
during hookup to avoid performance issues
and/or damage to your amplifier.
All speaker connections should be
made with the provided wire nuts. We
recommend filling each wire nut with
a little silicone sealant to ensure a
weatherproof connection.
Connect one end of the left and right
channel of the 4 conductor Direct Burial
speaker wire to the+/- terminals of the
amplifier's left and right output channel.
Next run the other end into the supplied
IPX7 Junction Box as shown in Fig 1.
Run the supplied Direct Burial speaker
wire from the SUBl00 subwoofer to the
IPX7 Junction box as shown in Fig 1. The
wires are coded in the following manner:
Left Channel(+) is White, Left Channel(-)
is Green. Right Channel ( +) is Red, Right
Channel (-) is Black. You must always
connect the left and right channels to
achieve maximum output. Observe positive
(+) and negative(-) polarity. Reversing
polarity of a dual voice coil subwoofer will
result in very little bass output and possibly
damage the speaker or amplifier.
Connect one end of the 2 conductor Direct
Burial wire to the Left SAT300. Make
sure to note which color is connected to
the(+) and(-) speaker terminals. Next
run the other end into the supplied IPX7
Junction Box as shown in Fig 1. Repeat this
procedure for the Right SAT300 as shown
in Fig 1.
Connect the SUBl00 and Left and Right
SAT300 inside the Junction Box as shown
in Fig 2. with the supplied wire nuts.
Customer Service Hours of Operation: Monday-Friday 9AM-6PM EST
[email protected]

Fig. 1
Fig. 2
r
I
AMPLIFIER
L
2 CONDUCTOR
SPEAKER WIRE
Q-
,..
+ R
2 CONDUCTOR
-SPEAKER WIRE
I
I
I
I
/ \\
R L
+ - + -
00 00
O~:;
\~
' '.
\'<
4WAY
JUNCTION BOX
+ - - +
-
______ -J l ,J
> r
4 CONDUCTOR _,, \
SPEAKER WIRE
"'
'- 4 CONDUCTOR
SPEAKER WIRE
\, r--------------------- -,
,J SAT LEFT SUB VC 1 SUB vc 2 SAT RIGHT I
1N~~D~;~~~~6~Ne~x I w,.J~ ~LJ
I +- +- I
SAT
LEFT
+ -
SUB
VC1
+ -
____JI\ __
WIRE NUTS
./
j
'
+ -
L____ AMP LEFT_ AMP RIGHT ____ j
+ -
SUB
VC2
+ -
SAT
RIGHT
+ -
L WIRE NUTS
-,
I
L __ _
AMP LEFT AMP RIGHT I
_J
Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: +l 410-358-3600)

II
NOTE
You will need an additional 2 conductor and 4 conductor Direct Burial Underground speaker
wire if you want to run the SAT300's farther than the 3 feet provided. For distances of 100
feet or less we recommend 14 AWG (Gauge) wire. For distances greater than 100 feet we
recommend 12 AWG (Gauge).
Connecting 4
SAT300 loudspeakers (Parallel hook up) to the Direct Burial IPX 7 junction
box provided
The
Atrium SAT300 and Atrium SUBl00
each come with 3 feet of CL3 speaker wire,
which is rated for underground burial. If
you wish to place the SAT300's or SUB100
farther than 3 feet from the supplied
Junction Box than you will need to use
additional speaker wire.
The
SAT300 has two conductors-one red
that is labeled "+" and one black that is
labeled"-". The SUBl0 has four conductors
(white, green, red and black) because it has
a
dual voice coil. Follow the correct polarity
during hookup to avoid performance issues
and/or damage to your amplifier.
All speaker connections should be
made with the provided wire nuts. We
recommend filling each wire nut with a little
silicone sealant to ensure a weatherproof
connection.
Connect one end of the left and right
channel of the 4 conductor Direct Burial
speaker wire to the+/- terminals of the
amplifier's left and right output channel.
Next run the other end into the supplied
IPX7 Junction Box as shown in Fig 3.
Run
the supplied Direct Burial speaker
wire from the SUBl00 subwoofer to the
IPX7 Junction box as shown in Fig 3. The
wires are coded in the following manner:
Left Channel ( +) is White , Left Channel (-)
is Green. Right Channel(+) is Red, Right
Channel (-) is Black. You must always
connect the left and right channels to
achieve maximum output. Observe positive
(+) and negative(-) polarity. Reversing
polarity of a dual voice coil subwoofer will
result in very little bass output and possibly
damage the speaker or amplifier. Connect
the SUBl00 and 4 Left and Right SAT300's
inside the Junction Box as shown in Fig 4.
with the supplied wire nuts.
Customer Service Hours of Operation: Monday-Friday 9AM-6PM EST
[email protected]

Fig. 3
Fig. 4
r
I
AMPLIFIER
L
+ -
00
/ /
+
+
L
4CONDUCTOR
SPEAKER WIRE
4 CONDUCTOR_,,
SPEAKER
WIRE
I
+ R
4CONDUCTOR
SPEAKER WIRE
4WAY
·-JUNCTION BOX
I
\ 4 CONDUCTOR
',, SPEAKER WIRE
'r SAT2 -SAT! SUB ---- SUB-SAT! SAT2 --,
' J Le:: L~F?' v._c _, v: ~ Rl~H__T R~T
SERIES PARALLEL WIRING
INSIDE JUNCTION BOX
~~
SAT2
LEFT
+
SUB
VCl
+
SATl
LEFT
+
SUB
VCl
+ -
I
!/
WIRENUTS ~ -
+ - + -
AMP LEFT AMP RIGHT
AMP LEFT AMP RIGHT
SUB
VC2
+ -
SATl
RIGHT
+
\,\ /
\ \
le( WIRENUTS
SAT 2
RIGHT
+ -
-,
L _______ _ _
______ _j
Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: [phone])

LIMITED WARRANTY
Polk Audio, Inc. warrants to the original
purchaser only that this Polk Audio
Loudspeaker Product (the "Product")
will be free from defects in materials and
workmanship for a period of five (5) years
from the date of original retail purchase
from a Polk Audio Authorized Dealer.
However, this Warranty will automatically
terminate prior to the expiration of the five
(5) years if the original retail purchaser
sells or otherwise transfers the Product
to any other party. The original retail
purchaser shall hereinafter be referred
to as "you." To allow Polk Audio to offer
the best possible warranty service, please
fill out the Product Registration Card(s)
and send it to the Factory, at the address
provided on the Product Cards(s) within
ten (10) days of the date of purchase.
Defective Products must be shipped,
together with proof of purchase, prepaid
insured to the Polk Audio Authorized
Dealer from whom you purchased the
Product, or to the Factory at 1 Viper Way,
Vista, California 92081. Products must be
shipped in the original shipping container
or its equivalent; in any case the risk of
loss or damage in transit is to be borne by
you. If upon examination at the Factory
or Polk Audio Authorized Dealer it is
determined that the unit was defective
in materials or workmanship at any time
during this Warranty period, Polk Audio or
the Polk Audio Authorized Dealer will, at
its option, repair or replace this Product at
no additional charge, except as set forth
below. All replaced parts and Products
become the property of Polk Audio.
Products replaced or repaired under this
warranty will be returned to you, within a
reasonable time, freight prepaid.
This warranty does not include service or
parts to repair damage caused by accident,
disaster, misuse, abuse, negligence,
inadequate packing or shipping procedures,
commercial use, voltage inputs in excess
of the rated maximum of the unit,
cosmetic appearance of cabinetry not
directly attributable to defect in materials
or workmanship, or service, repair, or
modification of the Product which has not
been authorized or approved by Polk Audio.
This warranty shall terminate if the Serial
number on the Product has been removed,
tampered with or defaced. This warranty
is in lieu of all other expressed Warranties.
If this Product is defective in materials or
workmanship as warranted above, your sole
remedy shall be repair or replacement as
provided above. In no event will Polk Audio,
Inc. be liable to you for any incidental or
consequential damages arising out of the
use or inability to use the Product, even if
Polk Audio, Inc. or a Polk Audio Authorized
Dealer has been advised of the possibility
of such damages, or for any claim by any
other party. Some states do not allow the
exclusion or limitation of consequential
damages, so the above limitation and
exclusion may not apply to you.
All implied warranties on this Product are
limited to the duration of this expressed
Warranty. Some states do not allow
limitation on how long an implied Warranty
lasts, so the above limitations may not apply
to you. This Warranty gives you specific legal
rights, and you also may have other rights
which vary from state to state.
This
Warranty applies only to Products
purchased in the United States of America,
its possessions, and U.S. and NATO armed
forces exchanges and audio clubs. The
Warranty terms and conditions applicable to
Products purchased in other countries are
available from the Polk Audio Authorized
Distributors in such countries.
Customer Service Hours of Operation: Monday-Friday 9AM-6PM EST
[email protected]

HBP17978
opalk.
1 VIPER WAY
VISTA, CALIFORNIA 92081
[phone] (US & CAN, OUTSIDE US [phone])
WWW.POLKAUDIO.COM