Poly-Tex HG2000 User manual

HG2000
POTTING BENCH
ASSEMBLY INSTRUCTIONS
IMPORTANT ! ! !
P:\ACAD2\MANUALS\POTTING BENCH HG2000\HG2000 FRONT&BACK.idw 6/11/2007
SAFETY GUIDELINES
CARE & MAINTENANCE
TOOLS & EQUIPMENT REQUIRED
Limited Warranty
Poly-Tex, Inc. warrants its products to be free from defects in material and workmanship for a
period of (1) year from date of invoice. This warranty is provided to the original purchaser of the
product and is not transferable. Poly-Tex does not warrant parts not manufactured by Poly-Tex,
but does assign any transferable manufacturer or supplier warranties. Should any defect be
found, full repair or replacement will be rendered to the customer at no cost following inspection
by a Poly-Tex representative and the return of the defective product to our Castle Rock, MN
factory. Expenses for removal or reinstallation of defective products will not be covered by the
warranty.
POLY-TEX SHALL NOT BE HELD RESPONSIBLE FOR ANY SPECIAL OR
CONSEQUENTIAL DAMAGES, OR FOR ANY DELAY IN PERFORMANCE OF THIS
WARRANTY BEYOND OUR CONTROL. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES WHETHER IMPLIED, WRITTEN OR ORAL INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
This warranty does not cover damage from customer abuse, misuse, improper installation,
customer modifications, customer negligence in performing normal maintenance, damage
resulting from acts of nature.
Contact information
Poly-Tex, Inc. PO Box 458
27725 Danville Ave Castle Rock, MN 55010
Toll free [phone] Fax [phone]
www.poly-tex.com
A 1/2" open-ended wrench is required to assemble this product.
Please read these instructions carefully before you start
to assemble this display. Save these instructions for future
reference.
Do not climb, sit on, or use this product as a ladder due to possible injuries.
Do not place or install electrical items on this product. Wet conditions are typical and
electrical shock is possible.
Do not place this product on a slope that exceeds 10 degrees.
To remove loose soil and debris, simply spray the soiled areas with a garden hose.
Prior to storage, all surfaces of this product should be sprayed down with water and allowed to dry
completely.

P:\ACAD2\MANUALS\POTTING BENCH HG2000\HG2000 2 & 3.idw 6/11/2007
ASSEMBLY INSTRUCTIONSPARTS IDENTIFICATION
.
.
24" x 44" TABLE TOP
(NT1000)
QTY (1)
10" x 44" UPPER SHELF
(NT1009)
QTY (1)
30" LEG
(NT1003)
QTY (2)
43" LEG
(NT1013)
QTY (2)
CAP SCREW
(NB1970)
QTY (12)
LOCK WASHER
(NB1862)
QTY (12)
HEX NUT
(NB1872)
QTY (12)
FLAT WASHER
(NB1886)
QTY (12)
1. PLACE 30" (SHORTER) LEGS INSIDE
TABLE TOP AS SHOWN.
2. FASTEN TO TABLE TOP USING CAP
SCREWS, FLAT WASHERS, LOCK
WASHERS, AND HEX NUTS.
3/16" HEX WRENCH
(NB1974)
QTY (1)
CAP SCREW
HEX NUT
LOCK WASHER
FLAT WASHER
3. PLACE 43" (LONGER) LEGS OUTSIDE
OF TABLE TOP AS SHOWN.
4. FASTEN TO TABLE TOP USING CAP
SCREWS, FLAT WASHERS, LOCK
WASHERS, AND HEX NUTS.
5. PLACE UPPER SHELF OVER TOPS OF 43"
LEGS AND FASTEN USING HARDWARE
PROVIDED.
LEG IS ON OUTSIDE
OF TABLE TOP
SHELF IS ON OUTSIDE
OF 43" LEGS
30" LEG
30" LEG
43" LEG

P:\ACAD2\MANUALS\POTTING BENCH HG2000\HG2000 2 & 3.idw 6/11/2007
ASSEMBLY INSTRUCTIONSPARTS IDENTIFICATION
.
.
24" x 44" TABLE TOP
(NT1000)
QTY (1)
10" x 44" UPPER SHELF
(NT1009)
QTY (1)
30" LEG
(NT1003)
QTY (2)
43" LEG
(NT1013)
QTY (2)
CAP SCREW
(NB1970)
QTY (12)
LOCK WASHER
(NB1862)
QTY (12)
HEX NUT
(NB1872)
QTY (12)
FLAT WASHER
(NB1886)
QTY (12)
1. PLACE 30" (SHORTER) LEGS INSIDE
TABLE TOP AS SHOWN.
2. FASTEN TO TABLE TOP USING CAP
SCREWS, FLAT WASHERS, LOCK
WASHERS, AND HEX NUTS.
3/16" HEX WRENCH
(NB1974)
QTY (1)
CAP SCREW
HEX NUT
LOCK WASHER
FLAT WASHER
3. PLACE 43" (LONGER) LEGS OUTSIDE
OF TABLE TOP AS SHOWN.
4. FASTEN TO TABLE TOP USING CAP
SCREWS, FLAT WASHERS, LOCK
WASHERS, AND HEX NUTS.
5. PLACE UPPER SHELF OVER TOPS OF 43"
LEGS AND FASTEN USING HARDWARE
PROVIDED.
LEG IS ON OUTSIDE
OF TABLE TOP
SHELF IS ON OUTSIDE
OF 43" LEGS
30" LEG
30" LEG
43" LEG

HG2000
POTTING BENCH
ASSEMBLY INSTRUCTIONS
IMPORTANT ! ! !
P:\ACAD2\MANUALS\POTTING BENCH HG2000\HG2000 FRONT&BACK.idw 6/11/2007
SAFETY GUIDELINES
CARE & MAINTENANCE
TOOLS & EQUIPMENT REQUIRED
Limited Warranty
Poly-Tex, Inc. warrants its products to be free from defects in material and workmanship for a
period of (1) year from date of invoice. This warranty is provided to the original purchaser of the
product and is not transferable. Poly-Tex does not warrant parts not manufactured by Poly-Tex,
but does assign any transferable manufacturer or supplier warranties. Should any defect be
found, full repair or replacement will be rendered to the customer at no cost following inspection
by a Poly-Tex representative and the return of the defective product to our Castle Rock, MN
factory. Expenses for removal or reinstallation of defective products will not be covered by the
warranty.
POLY-TEX SHALL NOT BE HELD RESPONSIBLE FOR ANY SPECIAL OR
CONSEQUENTIAL DAMAGES, OR FOR ANY DELAY IN PERFORMANCE OF THIS
WARRANTY BEYOND OUR CONTROL. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES WHETHER IMPLIED, WRITTEN OR ORAL INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
This warranty does not cover damage from customer abuse, misuse, improper installation,
customer modifications, customer negligence in performing normal maintenance, damage
resulting from acts of nature.
Contact information
Poly-Tex, Inc. PO Box 458
27725 Danville Ave Castle Rock, MN 55010
Toll free [phone] Fax [phone]
www.poly-tex.com
A 1/2" open-ended wrench is required to assemble this product.
Please read these instructions carefully before you start
to assemble this display. Save these instructions for future
reference.
Do not climb, sit on, or use this product as a ladder due to possible injuries.
Do not place or install electrical items on this product. Wet conditions are typical and
electrical shock is possible.
Do not place this product on a slope that exceeds 10 degrees.
To remove loose soil and debris, simply spray the soiled areas with a garden hose.
Prior to storage, all surfaces of this product should be sprayed down with water and allowed to dry
completely.