Polycool Cv700 User manual

Model shown is the CV800

Evaporative Cooler – CV700, CV800

User Manual

[Revision 2.0 February 2019]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY

DAMAGE AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by

this manual may vary in appearance, assembly, inclusions, specifications, description and packaging.

Evaporative Cooler - CV700, CV800

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death,

injury or equipment or property damage if not understood or followed. Safety messages have the

following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you

do not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you

do not follow instructions.

You CAN be INJURED if you

do not follow instructions or

equipment damage may occur.

It is vital that you read and understand

this user manual before using the product,

including safety warnings, and any

assembly and operating instructions.

Keep the manual for future reference.

Safety precautions and recommendations

detailed here must be fully understood

and followed to reduce the risk of injury,

fire, explosion, electrical hazard, and/or

property damage.

Safety information presented here is

generic in nature – some advice may not

be applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered

or combustion engine powered.

•Before Use - If you are not familiar with

the safe operation/handling of the

equipment, or are in any way unsure of

any aspect of suitability or correct use

for your application, you should

complete training conducted by a

person or organization qualified in safe

use and operation of this equipment,

including fuel/electrical handling and

safety.

•Do NOT operate the equipment in

flammable or explosive environments,

such as in the presence of flammable

liquids, gases or dust. The equipment

may create sparks or heat that may

ignite flammable substances.

•Keep clear of moving parts.

•Equipment may be a potential source of

electric shock or injury if misused.

•Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

•Do NOT allow others to use the

equipment unless they have read this

manual and are adequately trained.

•Keep packaging away from children -

risk of suffocation! Operators must use

the equipment correctly. When using

the equipment, consider conditions and

pay due care to persons and property.

General Work Area Safety

•Work areas should be clean and well it.

•Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

•If devices are provided for connecting

dust extraction / collection facilities,

ensure these are connected and used

properly. Dust collection can reduce

dust-related hazards.

General Personal Safety

•Wear appropriate protective equipment

when operating, servicing, or when in

the operating area of the equipment to

help protect from eye and ear injury,

poisoning, burns, cutting and crush

injuries. Protective equipment such as

safety goggles, respirators, non-slip

safety footwear, hard hat, hearing

protection etc should be used for

appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective

equipment. Do not wear loose clothing

or jewellery, which can be caught in

moving parts. Keep hair and clothing

away from the equipment.

•Stay alert and use common sense

when operating the equipment. Do not

over-reach. Always maintain secure

footing and balance.

•Do not use the equipment if tired or

under the influence of drugs, alcohol or

medication.

•This equipment is not intended for use

by persons with reduced physical,

sensory or mental capabilities.

General Fuel Safety

•Petrol/fuel/gasoline is extremely

flammable – keep clear of naked

flames or other ignition sources.

•Do not spill fuel. If you spill fuel, wipe it

off the equipment immediately – if fuel

gets on your clothing, change clothing.

•Do NOT smoke near fuel or when

refuelling.

•Always shut off the engine before

refuelling.

•Do NOT refuel a hot engine.

•Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

•Always refuel in well ventilated areas.

•Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•Using a combustion engine indoors

CAN KILL IN MINUTES. Engine

exhaust contains carbon-monoxide – a

poison you cannot smell or see.

•Use combustion engines OUTSIDE

only, and far away from windows, doors

and vents.

General Equipment Use and Care

•The equipment is designed for

domestic use only.

•Handle the equipment safely and

carefully.

•Before use, inspect the equipment for

misalignment or binding of moving

parts, loose components, damage or

any other condition that may affect its

operation. If damaged, have the

equipment repaired by an authorised

service centre or technician before use.

•Prevent unintentional starting of the

equipment - ensure equipment and

power switches are in the OFF position

before connecting or moving

equipment. Do not carry equipment

with hands or fingers touching any

controls. Remove any tools or other

items that are not a part of the

equipment from it before starting or

switching on.

•Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be

safer when used within its design and

usage parameters.

•Use the equipment and accessories

etc. in accordance with these

instructions, considering working

conditions and the work to be

performed. Using the equipment for

operations different from those

intended could result in hazardous

situations.

•Always keep equipment components

(engines, hoses, handles, controls,

frames, housings, guards etc) and

accessories (cutting tools, nozzles, bits

etc) properly maintained. Keep the

equipment clean and, where applicable,

properly lubricated.

•Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the

equipment near flammable materials,

combustible gases or liquids etc.

•The equipment is not weather-proof,

and should not be stored in direct

sunlight, at high ambient temperatures

or locations that are damp or humid.

•Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

•For specific equipment safety use and

care, see Equipment Safety.

Evaporative Cooler - CV700, CV800

General Electrical Safety

•Inspect electrical equipment, extension

cords, power bars, and electrical fittings

for damage or wear before each use.

Repair or replace damaged equipment

immediately.

•Ensure all power sources conform to

equipment voltage requirements and

are disconnected before connecting or

disconnecting equipment.

•When wiring electrically powered

equipment, follow all electrical and

safety codes.

•Wherever possible, use a residual

current device (RCD).

•High voltage / high current power lines

may be present. Use extreme caution

to avoid contact or interference with

power lines. Electrical shock can be

fatal.

General Electrical Safety

•Electrically grounded equipment must

have an approved cord and plug and

be connected to a grounded electrical

outlet.

•Do NOT bypass the ON/OFF switch

and operate equipment by connecting

and disconnecting the electrical cord.

•Do NOT use equipment that has

exposed wiring, damaged switches,

covers or guards.

•Do NOT use electrical equipment in wet

conditions or in damp locations.

•Do NOT use electrical cords to lift,

move or carry equipment.

•Do NOT coil or knot electrical cords,

and ensure electrical cords are not trip

hazards.

•Remove all packing materials from this

product before using it. This appliance

must be installed on a flat surface.

Please ensure the electric supply to this

appliance is disconnected before

installing.

General Service Information

•The equipment must be serviced or

repaired at authorised service centres

by qualified personnel only.

•Replacement parts must be original

equipment manufacturer (OEM) to

ensure equipment safety is maintained.

•Do NOT attempt any maintenance or

repair work not described in this

manual.

•After use, the equipment and

components may still be hot – allow the

equipment to cool and disconnect spark

plugs and/or electrical power sources

and/or batteries from it before making

adjustments, changing accessories or

performing repair or maintenance.

•Do NOT make adjustments while the

equipment is running.

•Perform service related activities in

suitable conditions, such as a

workshop.

•Replace worn, damaged or missing

warning/safety labels immediately.

Evaporative Cooler Safety

•Always operate the unit from a power source of the same voltage, frequency and rating as indicated on the product identification

marking.

•Do not operate this product if it has malfunctioned, damaged cord or plug or appears damaged in any way. Return the complete

product to the place of purchase for inspection, repair or replacement.

•This product should not be used in the immediate vicinity of water, such as bathtub, washbowls, swimming pool, etc. where the

likelihood of immersion or splashing could occur.

•Always switch OFF and unplug the plug from outlet when not in use, before assembling or disassembling parts and before cleaning.

Fully assemble the air cooler before operating.

•Avoid contacting with moving parts.

•Do not insert any object through the air outlet when the air cooler is operating.

•Do not cover the guard or operate near curtains, etc.

•Always disconnect the fan when moving it from one location to another.

•In high humidity season, it is better to choose wind mode as there is humidifying effect in cool mode.

•After adding water, do not tilt, collide, lay or move the machine to any position that will make the water overflow. Do not overturn the

machine.

•Do not cover the air outlet, at least a 1-meter distance space should be provided in front and back of the machine.

•Clean the product with a wet cloth. Do not flush it with water directly.

•If the unit with water is overturned, pull the power plug immediately. You should only restart the unit after it thoroughly dries out,

otherwise, it may cause malfunction.

•Do not face the air outlet near a wall or window curtains as it may block air flow.

•If the machine is not in use, pull the power plug out.

Evaporative Cooler - CV700, CV800

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols

on your product and their meanings. If any stickers become unreadable, unattached etc, replace them.

Flammable Material Hazard

Flammable liquids, gases or

substances etc may present.

Avoid ignition sources and

open flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc

before using the product.

Use Hand Protection

Wear appropriate hand

protection and take due care

as the product or use of the

product may present hand

hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be

fatal.

Electrocution / Electrical

Shock Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling

electrical products, cables,

plugs and leads. Electrical

shock can be fatal.

Toxic Fumes / Dust Hazard

Using the product or by-

products from use may

produce fumes, smoke or

particles that could be harmful

if inhaled. Wear appropriate

breathing protection and have

adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases or

substances etc may be

present. Avoid ignition sources

and open flames. Danger of

explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices

that can cause severe cut

injury to fingers, limbs etc.

Take due care when handling

and using the product.

Crush Hazard

The product may have blades,

edges or mechanical devices

that can cause severe crush

injury to fingers, limbs etc.

Take due care when handling

and using the product.

Single Operator Only

The product must be operated

by a single person only. More

than one person operating the

product may introduce

additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care

as the product or use of the

product may present face and

eye hazards.

Use Foot Protection

Wear appropriate foot

protection and take due care

as the product or use of the

product may present foot

hazards.

Use Eye / Ear / Head

Protection

Wear appropriate eye and / or

ear and / or head protection

and take due care as the

product or use of the product

may present eye, hearing and

head hazards.

Running Hazard

Do not run on or near the

product as doing so may

present a fall hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or

objects that can cause severe

injury to fingers, limbs, blood

etc. Take due care when

handling and using the

product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures

and hot surfaces that can

cause burn injuries.

Flying Debris Hazard

Be aware that the product or

use of the product may

present hazards produced by

flying debris. Wear appropriate

clothing and protectiove

devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts

to stop fully before handling

the product, adjusting,

maintenence etc.

Evaporative Cooler - CV700, CV800

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be

fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due

care when handling and using

the product.

Slope / Fall Injury Hazard

Be aware that using the

product on sloping surfaces or

in slippery conditions may

present additional dangers

from falls and contact with

blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

maneouvres as this may result

in severe injury due to falling,

product breakage or collapse

etc.

Electrocution / Electrical

Shock Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do

NOT use in rain, damp or wet

conditions. Electrical shock

can be fatal.

Electrocution / Electrical

Shock Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product.

Always disconnect the product

from the electrical supply

before handling the product,

adjusting, maintenence etc.

Power Line Electrocution

Hazard

High voltage / high current

power lines may be present.

Use extreme caution to avoid

contact or interference with

power lines. Electrical shock

can be fatal.

"Kick-Back" Hazard

High level of "kick-back"

hazard that can cause the

machine to suddenly rotate

towards operator. Kick-back

injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch

to move people.

Winch Lift Hazard

Do NOT LIFT load vertically.

Use machine to PULL only.

Cable Hazard

Ensure that load bearing cable

is not kinked or knotted.

Winch Cable Hazard

Ensure that there is a

minimum number of cable

coils on winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye

protection for welding. Dorect

exposure to weld arcs may

cause permanent eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser, or allow

others to.

Evaporative Cooler - CV700, CV800

Table of Contents

Safety...................................................................................................................................................2

Safety Symbols ..........................................................................................................................................4

Introduction ........................................................................................................................................7

Range of Application..................................................................................................................................7

Usage Environment....................................................................................................................................8

Parts Identification.............................................................................................................................9

Installation ........................................................................................................................................10

Operation ..........................................................................................................................................10

Maintenance .....................................................................................................................................11

Cleaning the Interior.................................................................................................................................11

Troubleshooting...............................................................................................................................12

Specifications...................................................................................................................................13

CV700 ......................................................................................................................................................13

CV800 ......................................................................................................................................................13

Evaporative Cooler - CV700, CV800

Introduction

Evaporative air cooler is a kind of modern energy-saving product which is developed through years of

research and experiments. It has the following advantages:

1. Energy-saving: Up to 80% or more while comparing with traditional air-conditioner

2. Environment Protection: No discharge of hazardous substances and freon free during its

operation.

3. Efficient: Achieving the maximum cooling and purifying effect with minimum power consumption

Evaporative air cooler is developed as a new generation of products combining of climatic conditions,

which is using a new generation of blades with high speed and large air volume.

Its working principle is a "direct evaporative" humidification and cooling technology. Not only have

cooling functional but also can achieve cooling effect of air humidification. Continuously circulating

pump draws water from the water tank, and then the water distributed to the wet curtain. When the hot

air enters the wet curtain, which is a cell-type filter layer made of special material, and then it

exchanges energy with water, a satisfactory effect of cooling can be obtained. Pure cool and clean air

then blows indoors under a précised pressure rendered by air blower while the hot air goes out of the

room through open vents or windows. Such cycle achieves the goal of lowering the temperature in the

room.

Range of Application

Due to the remarkable advantages of evaporative air cooler in cooling, humidification, cleanness,

energy-saving and ventilation, it is used in many ventilation and cooling places. This product is mainly

used in the following places:

1. Electronics, electroplating, footwear, printing, plastics, clothing, packaging, food processing

industry.

2. Textiles, machinery, ceramics, chemical industry, metallurgy, glass, metal, leather and other

manufacturing.

3. Hospital, clinic, schools, waiting rooms, cafes, shopping malls, supermarkets, laundry room.

4. Offices, home, kitchens, market, large entertainment centre, underground parking room, stations

and other public places.

5. Greenhouse, flowers, poultry, livestock, and other types of farms.

6. Existing chiller air conditioning and auxiliary equipment used blower.

7. Places of high humidity required for indoor use.

Hot air

Water pump

Filter

Air-blower

Cool air

Water tank

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

Evaporative Cooler - CV700, CV800

Usage Environment

•Ambient temperature:10 – 45°C

•Environment Relative Humidity: ≤95%

•Atmospheric pressure: 86kpa~106kpa

•Voltage deviation does not exceed the rated voltage of ± 10%

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

Evaporative Cooler - CV700, CV800

Parts Identification

No. Name

1 LED control panel

2 Air outlet

3 Water level sensor

4 Casters

5 Water inlet

6 Water supply inlet

7 Water drainage

1

2

3

4

5

6

7

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

Evaporative Cooler - CV700, CV800

Installation

1. Open the package and take out the cooler.

2. When adding water, open the water inlet on the top cover, put the water into the water tank, then

observe the water level by the floating ball and pay attention to the following:

−Avoid splashing water into the motor to prevent electrical components from short circuiting.

−Water must be below the maximum level (-), otherwise water will overflow.

−Use clean water to fill up the cooler.

3. Turn the speed knob to stand-by mode to turn ON/OFF the fan, then you can select Speed, Swing,

and Cooling.

Operation

Horizontal Louvers: Manually adjust the horizontal louvers to change the direction of airflow (Up/Down).

Note: After plugging the unit to a power outlet, it will be on stand-by mode first with a buzzer ringing.

•Power: Once the unit is connect to a power outlet, press this button and turn ON the cooler. During

its initial use, the default setting is “Cool Mode”. Press the button in running condition, the cooler will

close all running movements (closed fans, pumps and display) into a shutdown state.

•Cool: Press this button to switch to Cool Mode. The control panel light will go ON and the unit will

start working after 30 seconds.

•Wind: Press this button to switch to wind mode.

•Speed: Press this button to adjust wind speed to Low, Medium or High.

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

Evaporative Cooler - CV700, CV800

•Swing: Press this button to adjust the louvers, the vertical louvers will automatically begin to move

from left to right.

•Sleep: Press this button to switch to Sleep Wind Mode.

•Ion: Press this button to release negative ions into the air.

•Timer:

−In Shutdown Mode, press the Timer button to enter a value to adjust the boot time. Continue

pressing the timer button. Used to adjust the timing of the boot time range from 1 to 12 hours.

−While in boot state, press the timer button, then enter a value to adjust the shutdown time.

continue pressing the timer button. Used to adjust the timing of the shutdown time range from 1

to 12 hours.

NOTE: • A buzzer will ring every time a button is pressed. Remote control operation is the same as with

the control panel. • When water level is below warning level, the water pump will stop running and

buzzer will automatically sound off. It will return to work after water has been added in.

Maintenance

Turn the power OFF before performing any maintenance or repair on the unit to prevent accidents from

occurring. To ensure the cooling effect of the unit, the body should be wiped by a clean cloth every day

or every week. The interior of the unit should be cleaned regularly at least once a month. The actual

cleaning time will vary depending on the cleanliness of the environment.

Cleaning the Interior

1. Loosen the rubber cover at the drain hole, then drain out all of the water in the water tank.

2. Remove the air inlet shutter together with the evaporation heat exchanger and rinse them with

clean water. Re-install them back after cleaning and drying them.

While cleaning, ensure that the water pressure isn’t too high. When cleaning the

honeycomb, please do not use acidic or alkaline detergents.

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

Evaporative Cooler - CV700, CV800

Troubleshooting

Troubles Common causes Solutions

Unable to start the

fan.

Power failure. Check power supply.

Switch burned. Inspect and repair the appliances. (only by an

authorised service centre).

No air flow.

Motor starter’s capacitor is

damaged.

Inspect and repair the appliances. (only by an

authorised service centre).

Motor is damaged. Inspect and repair the appliances. (only by an

authorised service centre).

Honeycomb or air filter is

blocked.

Remove the blockage. Clean out the

honeycomb or air filter.

Airflow isn’t cool.

Lack of water in the water tank. Add more water to the water tank.

Water pump is damaged. Inspect and repair the appliances. (only by an

authorised service centre).

Honeycomb is dirty. Clean the honeycomb.

Unpleasant odour. Water or honeycomb is dirty. Change the water and clean honeycomb.

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

Evaporative Cooler - CV700, CV800

Specifications

CV700

Colour Black

Body material Plastic

Water consumption 2 - 5L/h

Water tank capacity 60L

Max. Airflow 5,000m³/h

Wattage 300W

Current 1.25A

Fan Axial

Noise Level ≤55dB

Room area 25-35㎡

Motor 3 Speed, 1-phase

Input voltage 220V - 240V / 50Hz

Power Plug Australian Standard

CV800

Colour Black

Body material Plastic

Water consumption 2 - 5L/h

Water tank capacity 60L

Max. Airflow 8,000m³/h

Wattage 350W

Current 2.4A

Fan Axial

Noise Level ≤60dB

Room area 25-35㎡

Motor 3 Speed, 1-phase

Input voltage 220V - 240V / 50Hz

Power Plug Australian Standard

NOTE: Minimal assembly required on both models.

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety

Consult all documentation, packaging

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.

Before each use, check the product for

loose/broken/damaged/missing parts,

wear or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear or leaks.

Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.

Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.

The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.

This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business

or employee, or financially affect the user, business or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement or service by a technician

may cause financial loss, loss of employee time or an

inconvenience requiring compensation.

If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

PolyCool CV700 User manual

Popular Air Cleaner manuals by other brands