manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Polyform
  6. •
  7. Boating Equipment
  8. •
  9. Polyform A Series User manual

Polyform A Series User manual

Product Max. Circumference
A Series
A-0 25.1 in. 63.8 cm
A-1 34.5 in. 87.7 cm
A-2 45.5 in. 115.6 cm
A-3 53.4 in. 135.6 cm
A-4 64.4 in. 163.5 cm
A-5 84.8 in. 215.3 cm
A-6 106.8 in. 271.2 cm
A-7 122.5 in. 311.0 cm
F Series
F-1 18.8 in. 47.9 cm
F-02 23.6 in. 59.8 cm
F-2 25.7 in. 65.4 cm
F-3 25.7 in. 65.4 cm
F-4 26.7 in. 67.8 cm
F-5 34.5 in. 87.7 cm
F-6 34.5 in. 87.7 cm
F-7 47.1 in. 119.6 cm
F-8 47.1 in. 119.6 cm
F-10 56.5 in. 143.6 cm
F-11 66.6 in. 169.1 cm
F-13 91.1 in. 231.3 cm
Product Max. Circumference
G Series
G-3 17.3 in. 43.9 cm
G-4 20.4 in. 51.8 cm
G-5 27.6 in. 70.2 cm
G-6 34.5 in. 87.7 cm
HTM Series
HTM-1 19.8 in. 50.2 cm
HTM-2 26.7 in. 67.8 cm
HTM-3 33.0 in. 83.7 cm
HTM-4 42.4 in. 107.7 cm
LD Series
LD-1 27.0 in. 68.6 cm
LD-2 36.1 in. 91.7 cm
LD-3 42.4 in. 107.7 cm
LD-4 48.7 in. 123.6 cm
WS Series
WS-1 25.1 in. 63.8 cm
Note: Remove white plastic screw from the valve (located
near the ropehold). When inating with an air compressor,
set the psi to 2 lbs. pressure.
INFLATION CHART
INFLATION
Polyform products are designed to be inated to 2.1 lbs/0,15 bar of pressure. When inating with-
out a pressure gauge, ll the buoy or fender until the walls are fully expanded, but make certain
you can depress the wall at least 1/4 inch with light hand pressure. Measure the circumference and
compare it with the ination chart for proper pressure. Over ination will reduce the performance of
the product and may cause premature failure. Over ination voids the warranty.
Several types of air source may be used to inate
your Polyform products:
Polyform # 30 hand pump
Other hand or foot operated pumps
Air Compressor
Service Station Air Pump
Polyform ination adapter and valveAfter lling
the product to the correct size, remove the pump
(and ination adapter if used) and replace the
white screw. Remember that you are screwing a
plastic screw into plastic threads. The screw will
come to a stop when the screw head is ush with
the top of the valve casing. Do not force the screw
past this point or damage to the valve will occur.
Only when the white valve screw is completely
seated in the valve as described above is the
fender or buoy completely sealed.
Remove the white plastic screw from the valve
(located near the ropehold).
Polyform US ination valve with ination
adapterIf you are using a gas station or portable
air compressor, set your gauge at 2 PSI. Do not go
beyond this setting. Insert the ination adapter
in the valve opening and apply the nozzle to the
adapter and depress to start the air owing. If you
are using a hand or foot operated pump, insert
the ination adapter into the nozzle rst. The
adapter is threaded for your convenience.
Inating Polyform boat fendersFill the Polyform
fender or buoy until the walls are fully expanded.
The best way to check that is to measure the cir-
cumference of the particular product and match
the chart measurement.You should also be able
to easily push with your thumb and depress the
wall 1/4 inch.
STEP 1
STEP 5
STEP 2
STEP 3
STEP 4
NOTE: Do not use power drills/drivers to
tighten. The torque can easily drive the screw
through the valve.
INFLATION GUIDE

This manual suits for next models

38

Popular Boating Equipment manuals by other brands

DAVIS Mark 3 manual

DAVIS

DAVIS Mark 3 manual

Garelick 71095 Mounting and operating instructions

Garelick

Garelick 71095 Mounting and operating instructions

Harken 3355 instructions

Harken

Harken 3355 instructions

CMP Panther KPB30A installation manual

CMP

CMP Panther KPB30A installation manual

ZF ZF 45 IV operating instructions

ZF

ZF ZF 45 IV operating instructions

SLEIPNER MOTOR AS SIDE-POWER SE-50/140 S Installation and user manual

SLEIPNER MOTOR AS

SLEIPNER MOTOR AS SIDE-POWER SE-50/140 S Installation and user manual

Westland 2-Bow Aluminum Bimini manual

Westland

Westland 2-Bow Aluminum Bimini manual

Humphree SU553 Installation drawing

Humphree

Humphree SU553 Installation drawing

Power-Pole 8 instructions

Power-Pole

Power-Pole 8 instructions

Sierra EVINRUDE-JOHNSON CARBURETOR Quick start quide

Sierra

Sierra EVINRUDE-JOHNSON CARBURETOR Quick start quide

Vetus Bullflex installation instructions

Vetus

Vetus Bullflex installation instructions

Floe V-2000 Assembly instructions

Floe

Floe V-2000 Assembly instructions

Seakeeper 1 Operation manual

Seakeeper

Seakeeper 1 Operation manual

Maretron SSC200 user manual

Maretron

Maretron SSC200 user manual

Engbo XF 30 VR Installation and user manual

Engbo

Engbo XF 30 VR Installation and user manual

hsr-benelli S-series Service manual

hsr-benelli

hsr-benelli S-series Service manual

MINN KOTA i-Pilot Link Quick reference guide

MINN KOTA

MINN KOTA i-Pilot Link Quick reference guide

Malone MPG461GU instructions

Malone

Malone MPG461GU instructions

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.