Polygroup Corona TG50ON041P00 User manual

MODEL #: TG50ON041P00
Congratulations on purchasing your new tree from Polygroup®! Carefully follow the instructions below
on how to quickly and easily set up your new tree.
TREE ASSEMBLY INSTRUCTIONS
4
3
2
1
Fig. A
Fig. B
*Electrical Rating For The Tree
(For Indoor Use Only)
Input: 120V AC, 60Hz, 0.6A
Output: 29V DC, 0.28A
5. Shape and shift tree branches to fill in any gaps.
1. Before you start to assemble your tree, choose an
appropriate location near a wall outlet.
3. Make sure the sensor faces towards the direction
people may pass.
4. Hang Wooden board and make sure the board
Faces towards the direction people may pass.
See Fig.B.
2. Insert tree body 2into the top hole of the stand 1.
Make sure the rivet cap of the tree body 2is
inserted into the slot of the collar of the stand 1.
And then Insert next section of the tree body 3into
tree body 2. Make sure the rivet cap of the tree
body 3is inserted into the slot of the collar of tree
body 2. Finally, Insert the tree top 4into the tree
body 3. See Fig.A.
Your tree should now be lit when you push the
switch button to Mode I or II . If some bulbs do not
light or flicker in Mode I, search for any bulbs loose,
missing, or broken bulbs. Replace bulbs promptly in
order to maintain the performance of your pre-lit tree.
6. Connect the Adaptor into the wall outlet.
Push the switch button to select below modes.
0: OFF.
I: Multi-steady light. Motion disabled.
II: Motion activated with sound and multi-fading.
Rivet cap on
the opposite side
Pull out
protective
cover
Slot of the
collar
No rivet on
the tree top
Pull out
protective
cover
Slot of the
collar
Rivet cap
Pull out
protective
cover
Slot of the
collar
PIR Sensor
Part
1
2
3
Description
Wooden board
Tree Body
Quantity
1
1
2
4
Tree Top
1
PACKAGE CONTENTS
Tree Body
MADE IN CHINA
1
ASSEMBLY INSTRUCTIONS

STORAGE INSTRUCTIONS:
TROUBLESHOOTING TIPS
For Pre-lit Trees, If The Tree Does Not
Illuminate
1. Please check to make sure that all plugs are properly
connected according to the color labels indicated in
Fig.C and the adaptor is plugged into the wall
outlet. Refer to assembly guide for instructions.
2. Please check for loose, broken, or missing light bulbs
and replace as needed.
1. Use only the adaptor supplied with this product.
Using a different adaptor will damage the lights and
cause fire, electrical shock hazards.
2. FOR INDOOR USE ONLY.
3. The external flexible cable or cord of this luminaire
cannot be replaced; If the cord is damaged, the
luminaire shall be destroyed.
1. Remove all ornaments and decorations. For pre-lit trees, first unplug adaptor from the wall outlet and
then disconnect light extension cord between each section of the tree.
2. Disassemble the tree from the top to the bottom. Start with the tree top and gently lift straight up to
remove from section below.
3. In case of difficulty separating the tree pole (trunk), apply a small amount of lubricant at the joint and
rotate the upper pole in both directions. Lift up the upper pole again.
4. Continue by gently lifting straight up each section(s) from the section below and fold all tips toward
the pole until the bottom section is removed from the tree stand.
5. Carefully place all tree sections into shipping box and tape it shut.
6. When not in use, please store your tree in a cool, dry place away from sunlight. Exposing your tree to
excessive heat or humidity may damage your tree.
Fig. C
Adaptor
To Be Plugged
Into Wall
Outlet
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed including the following:
a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When
products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
c.This seasonal use product is not intended for permanent installation or use.
d. Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
e. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
f. Do not let lamps rest on the supply cord or on any wire.
g. Unplug the product when leaving the house, when retiring for the night, or if left unattended.
h.This is not a toy. For decorative use only! To avoid risk of fire, burns, personal injury and electric shock it
should not be played with or placed where small children can reach it.
i. Do not use this product for other than its intended use.
j. Do not hang ornaments or other objects from cord, wire, or light string.
k. Do not close doors or windows on the product or extension cords as this may damage wire insulation.
l. Do not cover the product with cloth, paper or any material not part of the product when in use.
m.This product is equipped with push-in type lamps. Do not twist lamps.
n. Read and follow all instructions that are on the product or provided with the product.
o. SAVE THESE INSTRUCTIONS
WARNING
Insert Green
Label Extension
Cord into Adaptor
MADE IN CHINA
2
ASSEMBLY INSTRUCTIONS

CUSTOMER SERVICE FOR CHRISTMAS TREES
For any questions, assistance, or missing parts, Do Not Return To Place Of Purchase. Please contact
us at 1-888-919-0070 or visit our website at www.polygroupstore.com. One of our customer service
representatives will be happy to assist you.
TREE ID# IS LOCATED ON END PANEL OF BOX.TREE ID# IS REQUIRED WHEN REQUESTING REPLACEMENT PARTS.
Customer Name:
Address(No P.O. Boxes):
City & State:
Zip Code:
Day Phone:
Date Purchased:
Tree ID#:
Tree UPC#:
Store Purchased:
Specify Problem:
USER SERVICING INSTRUCTIONS
Lamp Replacement
Step 1. Unplug from power source, by pulling out the adaptor itself - do not pull on the power cord.
(For reference only)
Step 3. Replace with a new spare
LED lamp (included).
Step 2. Lift up the lamp lock tab,
and pull the bulb and its
plastic base straight out
from the lampholder.
CAUTION:
1. Risk of fire. Use only the power adaptor provided with this product. Do not replace lamps with other
than the spare lamps provided with this product.
2.To reduce the risk of fire and electric shock:
a. Do not mount or support light strings in a manner that can cut or damage wire insulation, and
b. Use only the power supply cord provided with this product.
MADE IN CHINA
3
ASSEMBLY INSTRUCTIONS