Home Accents Holiday 1004363936 User manual

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a) READ AND FOLLOW ALL SAFETY
INSTRUCTIONS.
b) This product is for indoor use only. The electrical rating 0.6 A 120 V 60
Hz.
c) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor applications,
connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If
one is not provided, contact a qualified electrician for proper installation.
d) This seasonal use product is not intended for permanent installation or
use.
e) Do not mount or place near gas or electric heaters, fireplace, candles or
other similar sources of heat.
f) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
g) Do not let lamps rest on the supply cord or on any wire.
h) Unplug the product when leaving the house, when retiring for the night,
or if left unattended.
i)Thisisanelectricproduct–notatoy! Toavoidriskoffire,burnspersonal
injuryandelectricshockitshouldnot beplayedwithorplacedwheresmall
children can reach it.
j) Do not use this product for other than its intended use.
k) Do not hang ornaments or other objects from cord, wire, or light string.
l) Do not close doors or windows on the product or extension cords as this
may damage the wire insulation.
m)Do not cover theproductwithcloth,paperoranymaterialnotpartof the
product when in use.
n)This product employs overload protection (fuse). A blown fuse
indicates an overload or short-circuit situation. If the fuse blows, unplug
theproduct fromthe outlet. Alsounplugany additional stringsorproducts
that may be attached to the product. Replace the fuse as per the User
Serving instructions (follow product marking for proper fuse rating) and
check the product. If the replacement fuse blows, a short-circuit may be
present and the product should be discarded.
o) Read and follow all instructions that are on the product or provided with
the product.
p) SAVE THESE INSTRUCTIONS.
CAUTION! – ALWAYS UNPLUG YOUR TREE
FROM ITS POWER SOURCE BEFORE ASSEMBLING OR
DISASSEMBLING.
CAUTION: The product consists of non-replaceable LED
lamps. To reduce the risk of fire or electric shock, do not attempt to
replace lamps or modify string.
9 ft Elegant Natural Fir LED Pre-Lit Tree with
Timer
SKU# 1004363936
Package Contents
A. Top Section
Qty: 1
B. UpperMiddle
Section
Qty:1
C. LowerMiddle
Section
Qty:1
D. Bottom Section
Qty: 1
E. Standwithan
eyebolt
Qty:1
F. PowerCord
Qty:1

G. Remote Control
Qty: 1
H. Fuse
Qty:2


Assembly
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step2. Open the standto a 90 degree angleuntil the hole linesupwith the
hole on the tube.
Step 3. Screw an eye bolt into the hole.
Pre-Assembly

Assembling the tree
Pleaseremove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Insert tree bottom (D) into the tree stand and tighten the screw.
(See Fig. 1)
Step2. Insertlowermiddlesection(C)intothetreebottom(D).(SeeFig.2)
Step 3 Insert upper middle section (B) into the lower middle section (C).
(See Fig. 3)
Step 4. Insert tree top (A) into the upper middle section (B). (See Fig. 4)
Warning: There is a tree top connector on the tree top (A). Do
not overload. Connect other lighting strings or tree toppers
end-to-end up to a maximum of 216 Watts (1.8 Amps). Do not
interconnect low-voltage products.
Step 5. Insert the provided power cord into the connector on the tree
bottom (D) in right direction porperly and tightly (always match the
protuberance of the end connector of power cord to the concave
of the connector found on the tree bottom (D) according to the
magnified drawing on fig. 5.).
Step6. Allowbranchestofall into placeorgentlypull branchesup andout.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 6)
Step 7. Shape the branches. Starting with tips closest to the pole, shape
one tip to the right, one to the left and oneat the center of the main
stem. Repeat pattern for each branch. (See Fig. 7)
Step 8. Plug the power cord into a proper outlet. The plugF1 controls the
treetoplights.TheplugF2controlsthetreelights.Thistree comes
with a control box and a remote control. You can change the
lightingpatternsofthetreebyusingcontrolboxorremotecontrol.
Please see Instructions of control box and remote control as
below.
Operation
Turning on the tree
Step 1. Connect each tree section well and plug the power cord into a wall
outlet.
Instruction of control box and remote
control
Instruction of control box
1. Press the ON/OFF Timer button on control box to turn on and off
timer function.
2. Press the Timer button on control box to select below timer hours:
i. Indicator lights of timer on control box turn on at 2 position:
The tree lights will automatically run through a 2-hours
ON, 22-hours OFF cycle.
ii. Indicator lights of timer on control box turn on at 4 position:
The tree lights will automatically run through a 4-hours
ON, 20-hours OFF cycle.
iii. Indicator lights of timer on control box turn on at 6 position:
The tree lights will automatically run through a 6-hours
ON, 18-hours OFF cycle.
iv. Indicator lights of timer on control box turn on at 8 position:
The tree lights will automatically run through an 8-hours
ON, 16-hours OFF cycle.
No memory mode on timer whether the tree or the timer is
re-started.
Instruction of remote control
Please note this tree has a remote control.
Please pull out the insulation tape from the remote control, before starting
to use it.
1. Press the button ON or OFF to turn on or off the lights.
2. Pressthe 2H,4H, 6H or 8H buttonto select the different timer hours.
If the remote control does not work, check whether the battery of the
remote control is out of power.
To replace the remote control battery:
1. Replace with a new button cell “CR2025” (3 volt)
into the compartment.
CAUTION: DO NOT DISPOSE OF BATTERIES IN
FIRE. BATTERIES MAY EXPLODE OR LEAK.
Maintenance
Replace the fuse.
Power cord plug F1 fuse replacement (replaceable 3 amp, 125 volt fuse
is located in spare parts bag):
1. Grasp plug and remove from the receptacle or other outlet device. Do
not unplug by pulling on cord.

2. Open fuse cover. Slide open the fuse access cover towards the
blades of the attachment plug.
3. Remove fuse carefully.
4. Risk of fire. Replace fuse only with 3 Amp,
125 Volt fuse (provided with product).
5. Close fuse cover. Slide closed the fuse access cover.
6. Risk offire.Donot replaceattachmentplug.Contains a safetydevice
(fuse) that should not be removed. Discard product if the attachment
plug is damaged.
CAUTION! – ALWAYS UNPLUG YOUR TREE FROM ITS
POWER SOURCE BEFORE ATTEMPTING FUSE REPLACEMENT.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the power cord from the wall outlet. And remove your
power cord from tree bottom (D) and save them.
Step3. Gentlyliftthe treetopstraightup toremovefromthe center section
and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step5. Carefullyplacealltreesectionsintoashippingboxandtapeitshut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
Problem Solution
The tree or
the tree top
does not
light
Ensure that all tree sections are connected into each
other well by pressing each section down and rotating.
Make sure the power cord is well connected to the
treebottom(D).EnsurethattheplugF2ispluggedinto
the plug F1 and then plugged into the wall outlet.
Check for blown fuses at the power cord plug F1.
Replace as needed with the replacement fuses
provided.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
Warning: Please note that changes or modifications
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and
receiver.
● Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician
for help.
Model No. LTW36C-12V1C