Polygroup TG76M3J72D02 User manual

1. Before you start to assemble your tree, choose an appropriate location near a wall outlet.
2. Assemble the tree stand and place on a level surface. (See Fig. A)
Congratulations on purchasing your new tree from Polygroup®! This tree comes with Quick Set® technology, allowing you to set
up and light up your tree in less than 10 minutes! Carefully follow the instructions below on how to quickly and easily set up your
new tree.
TREE ASSEMBLY INSTRUCTIONS
3. Each tree section is numbered with a sticker. Please identify all sections before assembling.
4. Assemble the tree from the bottom to the top.Start with the bottom section and remove protective cap before inserting into the
assembled stand.Make sure the pole is firmly inserted and secured into the stand.
5. Continue by inserting the upper tree section(s) to the lower section(s) until inserting the tree top.
6. Allow branches to fall into place or gently pull up and out.When adjusting branches, be sure that all
wires are free of branch hinges.
7. Plug in the adapter (connecting with the tree power cord) into the wall outlet (See Fig. B).Your entire tree should now be lit.If
some bulbs do not light or flicker, search for any loose plugs and/or broken, loose or missing bulbs. Replace bulbs promptly in
order to maintain the performance and life expectancy of your pre-lit tree. (Using a spare bulb included with your tree.)
8. Begin to shape the branches and tips working from the bottom to the top. Start with tips farthest from the pole and fan out one to
the right, one to the left and one at the center of the main stem. (See Fig. C)
Top view Side view
Fig. C
Fig. A - Tree Stand Assembly
Unfold the legs and lay the
stand in a flat area.Then slide
the locking disc downward
and snap into place.
MODEL #: TG76M3J72D02
*Electrical Rating For The Tree
(For Indoor Use Only)
Input: 100-240VAC, 50/60Hz, 0.35A
Output: 29V DC 0.45A
Fig. B - Tree and Light Assembly
Section 2
Tree top
Section 1
Control box Insert Green Label
Extension Cord
into Adapter
1
Plug Adapter
Into Wall
Outlet
Do Not Tamper
Internal Parts
Open the
protective
cap
Do Not Tamper
Internal Parts
Open the
protective
cap
NEED HELP?
DO NOT RETURN TO STORE. PLEASE VISIT US AT:
www.polygroupstore.com OR 1-888-919-0070

9. After shaping the entire tree following the previous step, slightly upsweep all branch tips for a uniform look. Shift branches to fill
any gaps.Your Christmas tree is now complete and ready to be decorated.
2
Lamp Replacement
Step 1.
Unplug from power source, by pulling out the adapter itself - do not pull on the power cord.
(For reference only)
Step 3. Replace with a new spare
LED lamp (included).
Step 2. Lift up the lamp lock tab,
and pull the bulb and its
plastic base straight out
from the lampholder.
Fig. D
1. Unplug adapter from the wall outlet first and then remove all ornaments and decorations.
2. Disassemble the tree from the top to the bottom. Start with the tree top and gently lift straight up to remove from section
below and fold all branches upwards toward the pole.
3. Continue by gently lifting each section straight up from the section below and fold all
branches upwards toward the pole until the bottom section is removed from the tree stand.
Cover the protective cap on the poles to avoid damaging the internal parts. (See Fig. D)
4. Carefully place all tree sections into shipping box and tape it shut.
5.When not in use, please store your tree in a cool, dry place away from
sunlight. Exposing your tree to excessive heat or humidity may damage your tree.
6. Keep out of reach of pets and children.
STORAGE INSTRUCTIONS
For Pre-lit Trees, If The Tree Does Not Illuminate
1. Please check to make sure that all plugs are properly connected and adapter is plugged into the wall outlet.
2.Turn the poles gently to make sure pole to pole sections are connected properly
3. Check for loose connection between light string plugs and extension cords.
4. Please check for loose, broken or missing light bulbs and replace as needed.
Loose Hinge Pin
1. Extra hinge pins are included for repairs, if needed.
Place the branch into the slot of the bracket.
2. Insert a new hinge pin through the hole and secure
using the retainer washer.(See Fig. E)
TROUBLESHOOTING TIPS
Each tree includes additional hinge pins/washers, and for pre-lit trees spare bulbs are also included.If extra parts are needed,please
contact our customer service center.
SPARE PARTS
Fig. E
HOW TO USE THE DUAL COLOR LIGHT CONTROLLER :
Press the selector button on the “Dual Color Light Controller” to select among:
(1) CLEAR-MULTI: FADING (2) CLEAR: FADING (3) CLEAR-MULTI: ALTERNATING
(4) CLEAR: STEADY (5) CLEAR-MULTI: SLOW FADING (6) MULTI: STEADY
(7) MULTI: FADING (8) COMBINATION Light
Controller
Selector
Button
CAUTION:
1.To reduce the risk of fire and electric shock:
a) Use only the power supply that was provided with this product;
b) Do not install on trees having needles, leaves or branch covering of metal or materials which look like metal, and
c) Do not mount or support strings in a manner that can cut or damage wire insulation.
2. Use only the adapter supplied with this product. Using a different adapter will damage the lights and may cause fire, or
electrical shock hazards.

CUSTOMER SERVICE FOR CHRISTMAS TREES
For any questions, assistance, or missing parts, Do Not Return To Place Of Purchase. Please contact us at 1-888-919-0070
or visit our website at www.polygroupstore.com.One of our customer service representatives will be happy to assist you.
Proof of purchase is required for warranty.
TREE ID# IS LOCATED ON END PANEL OF BOX.TREE ID# IS REQUIRED WHEN REQUESTING REPLACEMENT PARTS.
Customer Name:
Address(No P.O. Boxes):
City & State:
Zip Code:
Day Phone:
Date Purchased:
Tree ID#:
Tree UPC#:
Store Purchased:
Specify Problem:
3