Polypipe UFHTFTM User manual

User’s manual
UFHTFTM - TFT Master Room
Thermostat
EN
www.polypipeufh.com
User’s manual
UFHTFTM - TFT Master Room
Thermostat

2
User’s manual

Table of contents
I. Safety 4
II. Description 5
III. Installation 6
IV. How to use the controller 7
V. Operation modes 8
V.a) Schedule 8
V.b) Manual mode 9
VI. Zones 10
VI.a) Zone name 10
VI.b) Schedule settings 11
VI.c) Manual operation 12
VII. Controller menu 13
VII.a) Time settings 14
VII.b) Screen settings 14
VII.c) Alarm clock settings 16
VII.d) Controller settings 16
VII.e) Protections 17
VII.f) Language 17
VII.g) About the program 17
VIII. Protections 17
IX. Soware update 17
3
UFHTFTMBP, UFHTFTMWP

I. Safety
Before using the device for the fi rst time the user should read the following regulations
carefully. Not obeying the rules included in this manual may lead to personal injuries
or controller damage. The user’s manual should be stored in a safe place for further
reference. In order to avoid accidents and errors it should be ensured that every person
using the device has familiarized themselves with the principle of operation as well as
security functions of the controller. If the device is to be sold or put in a diff erent place,
make sure that the user’s manual is there with the device so that any potential user has
access to essential information about the device.
The manufacturer does not accept responsibility for any injuries or damage resulting from
negligence; therefore, users are obliged to take the necessary safety measures listed in
this manual to protect their lives and property.
WARNING
• High voltage! Make sure the regulator is disconnected from the mains before performing
any activities involving the power supply (plugging cables, installing the device etc.)
• The device should be installed by a qualifi ed electrician.
• Before starting the controller, the user shoud measure earthing resistance of the
electric motors as well as the insulation resistance of the cables.
• The regulator should not be operated by children.
WARNING
• The device may be damaged if struck by a lightning. Make sure the plug is disconnected
from the power supply during storm.
• Any use other than specifi ed by the manufacturer is forbidden.
• Before and during the heating season, the controller should be checked for condition of
its cables. The user should also check if the controller is properly mounted and clean
it if dusty or dirty.
Changes in the merchandise described in the manual may have been introduced
subsequent to its completion on February 28th 2016. The manufacturer retains the right
to introduce changes to the structure. The illustrations may include additional equipment.
Print technology may result in diff erences in colours shown.
We are committed to protecting the environment. Manufacturing electronic
devices imposes an obligation of providing for environmentally safe
disposal of used electronic components and devices. Hence, we have been
entered into a register kept by the Inspection For Environmental Protection.
The crossed-out bin symbol on a product means that the product may not
be disposed of to household waste containers. Recycling of wastes helps to
protect the environment. The user is obliged to transfer their used
equipment to a collection point where all electric and electronic components
will be recycled.
4
User’s manual

II. Description
UFHTFTM room regulator is intended for cooperation with UFH8ZMP Wiring Centre. It may
control the operation of subordinate room regulators.
UFHTFTM room regulator should be installed in a particular heating zone.
Temperature information sent by it to the external controller is used to control the
thermostatic valves (by opening them when the room temperature is too low and closing
them when the pre-set room temperature has been reached). The room regulator enables
the user to adjust the pre-set room temperature and set weekly temperature schedules.
UFHTFTM room regulator enables the user to adjust certain settings for other
zones e.g. the pre-set temperature value, weekly schedule, zone name etc.
NOTE
Only one UFHTFTM room regulator may be used in a heating system.
Functions fulfi lled by the regulator:
• Wireless communication with UFH8ZMP
• Controlling room temperature
• Displaying settings: temperature, date, time
• Screen adjusting its brightness to diff erent times of the day
• Parental lock
• Alarm clock
• Screensaver – possibility of uploading photos, a slide show
• Software update via USB
• Controlling the settings of other zones e.g. the pre-set temperature, schedules, names
etc.
• Possibility of confi guring global schedule settings
Controller equipment:
• Front panel made of 2mm glass
• Wireless communication
• Large, easy-to-read, colour touchscreen
• Built-in temperature sensor
• Flush-mountable
5
UFHTFTMBP, UFHTFTMWP

III. Installation
The controller should be installed by a qualifi ed person.
WARNING
Risk of fatal electric shock from touching live connections. Before working on
the controller switch off the power supply and prevent it from being accidentally
switched on.
WARNING
ncorrect connection of the wires may damage the controller!
230V 50 Hz
L N
USB
PORT
6
User’s manual

IV. How to use the controller
1. Enter the controller menu
2. Current time and date
3. Current status of particular zones:
4. Zone name – it may be changed in the zone menu or via the Internet website (using
UFHINTMODP or UFHINTWIFIP Internet modules)
5. Current zone temperature
5. Pre-set zone temperature
How to use the controller
12
3
4
5
6
7
UFHTFTMBP, UFHTFTMWP

V. Operation modes
V.a) Schedule
After a given schedule has been activated, the pre-set temperature is adjusted according
to the schedule settings. Separate temperature values may be assigned to the maximum
of 3 time periods (see: Schedule settings).
In order to change current schedule,
tap on the screen in the place where current
operation mode is displayed (see: point 2 in
Zones section). Choose desired schedule from
the list which appears of the screen and tap on
it.
The user may choose between 2 types of zone schedules:
- global schedule – its settings are pre-defi ned via the Internet website or UFHTFTM master
room regulator,
- local schedule – individual settings for a particular zone.
In order to confi gure detailed settings, go to Menu / Schedule settings.
8
User’s manual

V.b) Manual mode
In order to activate manual mode, tap on the pre-set temperature displayed on the main
screen. Next, set the pre-set temperature value and defi ne how long it should apply in the
zone.
The pre-set temperature may be
adjusted using ▲and ▼ icons, or by dragging
the temperature slider (displayed on the left-
hand side of the screen). Press OK to confi rm.
Next, the user defi nes the pre-set
temperature application time (when this period
is time is over, the controller returns to the
previous operation schedule).
By tapping on the clock icon the user
may set the pre-set temperature to apply for
an indefi nite period of time. The part of the
main screen labelled no. 4 displays “CON”.
9
UFHTFTMBP, UFHTFTMWP

VI. Zones
UFHTFTM is a master regulator – it means that it may be used to adjust most parameters
for other zones, regardless of the type of room regulator or room sensor used in the zones.
In order to edit parameters of a particular zone, tap on the area of the screen
where the current status of a given zone is displayed. A zone editing screen will appear:
1. Return to the main screen
2. Room regulator operation mode – the pre-set temperature depends on the current
schedule or manual settings (manual mode). Tap here to open up schedule selection screen.
3. Current time and date
4. Enter the zone menu – tapping on this icon opens up the following options: Zone name,
Schedule settings and Operation.
5. Pre-set zone temperature – tap here to adjust the temperature
6. Time left before the next pre-set temperature change
7. Current zone temperature
VI.a)Zone name
This function is used to edit the name of the zone. The user may assign a diff erent name
to each zone e.g. bathroom, kitchen etc.
123
4
5
7
6
10
User’s manual

VI.b)Schedule settings
UFHTFTM room regulator off ers two types of schedules – local and global.
Global schedules are available in all
zones – in each zone one of such schedules may
be activated. Their settings may be changed
only via the Internet website using the Internet
module or via UFHTFTM master room regulator.
Global schedule may also be used as a basis
for creating a local schedule. In order to do it,
edit a selected global schedule and confi rm the
changes – it will be saved as a local schedule.
Local schedule is assigned only to
the controlled zone and its settings may be
adjusted both from UFHTFT room regulator and master devices (UFH8ZMP Wiring Centre,
UFHTFTM master room regulator or via the Internet).
How to edit the schedule:
After entering the schedule editing screen, the schedule may be adjusted to the
user’s needs. The settings may be confi gured for two separate groups of days – the fi rst
group in orange, the second one in grey. It is possible to assign up to 3 time periods with
separate temperature values to each group. Outside these periods of time, a general pre-
set temperature will apply (its value may also be edited by the user
1. General pre-set temperature for the fi rst group of days (orange colour – in the example
above the colour is used to mark working days Monday-Friday). The temperature applies
outside the time periods defi ned by the user.
2. Time periods for the fi rst group of days – the pre-set temperature and the time limits.
Tapping on a given period opens up an editing screen.
3. General pre-set temperature for the second group of days (grey colour – in the example
above the colour is used to mark Saturday and Sunday).
4. Time periods for the second group of days. In the example above only one period has
been created. In order to add new periods, tap on „+”.
5. Days of the week – orange days are assigned to the fi rst group whereas grey days are
assigned to the second one. In order to change the group, tap on a selected day.
1 3
24
5
11
UFHTFTMBP, UFHTFTMWP

Time period editing screen enables the user to
adjust the pre-set temperature and the time
limits of the period with the accuracy of 15
minutes.
If the time periods overlap, they are marked
with red colour. Such settings cannot be
confi rmed.
VI.c) Manual operation
This function is used to deactivate a given zone by selecting OFF.
12
User’s manual

VII. Controller menu
Tap on the MENU icon on the main screen to enter the controller menu.
13
UFHTFTMBP, UFHTFTMWP

VII.a) Time settings
Tapping on this icon opens up a screen enabling the user to set the time, date and defi ne
the time limits for daytime and nighttime (Day from... and Night from...).
VII.b) Screen settings
Tap on this icon to adjust the screen settings to
individual needs.
Screensaver
The user may activate a screensaver which will appear after a pre-defi ned time of inactivity.
In order to return to the main screen view, tap on the screen. The following screensaver
settings may be confi gured by the user:
• Screensaver
After tapping on this icon, the user may deactivate the screen saver (No screensaver) or
set the screensaver in the form of:
- Slide show – (this option may be activated if the photos have been uploaded
fi rst). The screen displays the photos at a user-defi ned frequency.
- Clock – the screen displays the clock.
- Blank – after the pre-defi ned time of inactivity the screen goes blank
14
User’s manual

• Pictures import
Before importing the photos to the controller
memory they must be processed using
ImageClip (the software may be downloaded
from Polypipe.emodul.eu).
After the software has been installed and
started, load the photos. Select the area
of the photo which will be displayed on the
screen. The photo may be rotated. After one
photo has been edited, load the next one.
When all the photos are ready, save them in
the main folder of the memory stick. Next,
insert the memory stick into the USB port
and activate Photo upload function in the
controller menu.
It is possible to upload up to 8 photos. When
uploading new photos, the old ones are
automatically removed from the controller
memory.
• Idle time
This function is used to defi ne the time after
which the screensaver is activated.
• Slide show frequency
This option is used to set the frequency at
which the photos are displayed on the screen
if the Slide show is activated.
Screen brightness at daytime / screen brightness at nighttime
After tapping on screen brightness icon, the
user may adjust the screen brightness (in
percentages) both for the daytime and the
nighttime.
Screenshot from photo editing program for the
controller UFHTFTMBP, UFHTFTMWP
15
UFHTFTMBP, UFHTFTMWP

VII.c) Alarm clock settings
This submenu is used to activate and edit the
alarm clock function.
The alarm clock may be activated
once or on selected days of the week – select
the days in Alarm day option.
VII.d) Controller settings
Room temperature sensor
The following functions concern the built-in temperature sensor:
Hysteresis:
This function is used to defi ne tolerance of the pre-set temperature in order to prevent
undesired oscillation in case of small temperature fl uctuation (within the range 0 ÷
10⁰C) with the accuracy of 0,1°C.
Example: if the pre-set temperature is 23⁰C and the hysteresis is 1⁰C, the room temperature
is considered too low when it drops to 22⁰C.
Calibration
Calibration should be performed while mounting or after the regulator has been
used for a long time, if the room temperature measured by the sensor diff ers from
the actual temperature. Calibration setting range is from -10˚C to +10˚C with the
accuracy of 0,1˚C.
Registration
This function is used to register UFHTFTM room regulator in a selected zone. It should be
activated after a corresponding function in UFH8ZMP Wiring Centre has been activated -
see: UFH8ZMP instruction manual.
16
User’s manual

VII.e) Protections
Tapping on Protections icon in the main menu
opens up a screen enabling the user to confi gure
the parental lock function. When this function is
activated by selecting Automatic blockade on,
the user may set the PIN code necessary to
access to the controller menu.
NOTE
0000 is the default PIN code.
VII.f) Language
This function is sued to select the language version.
VII.g) About the program
When this option is selected, the screen
displays the controller manufacturer’s logo and
the current software version.
VIII. Protections
UFHTFTM room temperature regulator signalises all the alarms which occur in UFHTFTM
Wiring Centre. In case of an alarm, a sound signal is activated and the regulator display
shows the same message as the external controller display.
In the event of temperature sensor damage, the display shows the following message:
„Room temperature sensor damaged”.
IX. Software update
NOTE
Software update shall be conducted only by a qualifi ed fi tter. After the software
has been updated, it is not possible to restore previous settings.
In order to install new software, the controller must be unplugged from the power supply.
Next, insert the memory stick with the new software into the USB port. Connect the
controller to the power supply. A single sound signal signalises that the software update
process has been initiated.
17
UFHTFTMBP, UFHTFTMWP

18
User’s manual

19
UFHTFTMBP, UFHTFTMWP

[phone]
www.polypipeufh.com
Polypipe Building Products
Broomhouse Lane
Edlington
Doncaster
DN12 1ES