Portos RR1 User manual

R
INSTRUCTION MANUAL
RR1 / RR5 / RR15
Transmitters operate
on frequency
433 Mhz
Specification :
Nominal voltage: 3V
Battery type: CR 2430
Radio frequency: 433 Mhz
Transmit power: 10 mW
Ambient temperature: from -10 ˚C to +50 ˚C
Operating range: 150 m outside buildings
25 m indoors
Characteristics of the device:
P2
CR 2430
3V
MODE
TIME
UP
STOP
DOWN
UP
STOP
DOWN
UP
STOP
DOWN
ACTIVE
CHANNEL
ACTIVE
CHANNEL
P2
BATTERY
!!!
RR 1 RR 5 RR 15
CHANNEL
DOWN
CHANNEL
DOWN
CHANNEL UP
CHANNEL UP

The programming on the channel
Switch the electricity ON. The motor will make a short beep and will vibrate ( short
movement up & down ). The motor is in programming mode for 12 seconds. If no button
will be pushed within these 12 seconds the motor leaves the programming procedure.
Choose the channel that You wish to program ( for remotes with more than one
channel ).
1.Press the P2 button, the motor will emit a single sound.
2.Press again P2 button. The motor will emit a single sound again.
3.Press either button Up or DOWN. The programming will be confirmed by 6 short
beeps and after that the motor will vibrate, meaning that the programming was
successful.
After the programming procedure is finished You need to verify the directions on the
remote by simply starting the motor. If the directions are swapped then the
programming procedure needs to be done once more, eg:
If the motor has been programmed using the procedure two times P2 and then DOWN
button and the directions are swapped, then we need to program the motor again using
the opposite procedure, meaning two times P2 and then UP button.
ON
P2 MODE
TIME
P2 MODE
TIME
ON
P2 MODE
TIME
P2 MODE
TIME
!!! CAUTION!!
When programming, only the tubular motor which is to be programmed needs
to be power supplied.
2

Deleting a channel
Set the channel that You wish to delete.
1.Press P2 button, the motor will emit a single sound and will vibrate.
2.Press the STOP button. The motor will only emit a single sound.
3.Press again P2 button. The deleting procedure will be confirmed by 4 short beeps and
after that the motor will vibrate, meaning that the deleting was successful.
CAUTION !!!
If the settings of one channel will be deleted then all the motors that have been
programmed on this channel will be deleted as well. Each deleting and further
programming procedure requires the power to be switched on for each motor
individually, that is why it is recommended that each motor has its own power
supply separately assigned.
Adding another transmitter/channel
The procedure of adding a new transmitter/channel starts with the already working
transmitter. When adding a new transmitter/channel the power supply does not need to
be switched off and on again.
Set the channel that You want to add on a new transmitter.
1.Press P2 button on the already existing transmitter, the motor will emit a single sound
and will vibrate.
2.Press the P2 button again. The motor will only emit a single sound.
3.Now select the transmitter/channel on the new device and press P2 button ( or Up +
STOP buttons simultaneously, depending on the transmitter ). The motor confirms
by beeping 5 times. The new channel/transmitter is programmed.
P2 MODE
TIME
2x
P2 MODE
TIME
P2 MODE
TIME
P2 MODE
TIME
!!!
3

4. Switching the remote control between the switch and pushbutton
mode
The remote control can be operated in two modes:
Switch mode
By pressing and releasing the UP or DOWN button, the previously programmed
function of a motor will be activated (opening or closing the roller shutter). The motor will
work only when the button is being pressed. Releasing the key will stop the motor. After
pressing the button for longer than 2 seconds the motor will enter the switch mode, that
is, it will work until the roller shutter is completely closed or opened.
Pushbutton mode
By pressing and releasing the UP or DOWN button, the previously programmed
function of a motor will be activated (opening or closing the roller shutter). The motor will
work only when the button is being pressed. Releasing the key will stop the motor. After
pressing the button for longer than 2 seconds the motor will enter the switch mode, that
is, it will work until the roller shutter is completely closed or opened.
Switching between particular modes can be performed in the following way:
Choose the channel which has been previously programmed.
1.Press the P2 button once, the motor will emit a single sound.
2.Press the UP button, the motor will emit a single sound.
3.Press the P2 button again, it will be signaled by 3 sounds emitted by the motor
The shift of the mode on the remote control has been completed. This change relates to
all channels and remote controls that are going to be assigned to the motor.
Operating
The remote control’s range as well as the quality of radio signal can be influenced by
local interferences such as motors or other radio devices operating in the same
frequency. If there is no reaction of the motor when using the remote control, you should
send a command again after moving the remote control to another area of the room.
Device must be kept clean and protected from dirt. The device should not be exposed to
extreme temperature, moisture or vibrations. To change the battery you should take out
the device from the frame. The battery is located at the back of the device. While
changing the battery you should not use any metal tools. Only batteries CR2430 can be
used. After replacing the battery with the new one, the device is ready to work. The
controlling device should be protected from access of undesirable persons. Before
throwing away the device, remember to delete all motors assigned to it. The device that
is no longer needed, should be disposed of in accordance with the rules and regulations
of the country you inhabit.
CAUTION – PROCEEDINGS ACCORDING THIS MANUAL IS IMPORTANT FOR
THE SAFETY OF PEOPLE.
P2 MODE
TIME
P2 MODE
TIME
!!!
4