Portos RR-5T User manual

R
INSTRUCTION MANUAL
RR-5T
Transmitters operate
on frequency
433 Mhz
Specification :
Nominal voltage: 3V
Battery type: CR 2430
Radio frequency: 433 Mhz
Transmit power: 10 mW
Ambient temperature: from -10 ˚C to +50 ˚C
Operating range: 150 m outside buildings
25 m indoors
PORTOS Sp.J.
ul. Złota 71
62 - 800 Kalisz
tel. 62 / 768 40 00
[e-mail]
www.portosrolety.pl
Characteristics of the device:
!!!
RR-5T
man auto
Mode
The direction
of movement
UP
STOP
DOWN
CHANNEL UP
CHANNEL DOWN P2
CR 2430
3V
MODE
TIME
P2
BATTERY
Active
channel
Time
MODE
TIME

Switch the electricity ON. The motor will make a short beep and will vibrate ( short
movement up & down ). The motor is in programming mode for 12 seconds. If no button
will be pushed within these 12 seconds the motor leaves the programming procedure.
Choose the channel that You wish to program ( for remotes with more than one
channel ).
1.Press the P2 button, the motor will emit a single sound.
2.Press again P2 button. The motor will only emit a single sound.
3.Press either button Up or DOWN. The programming will be confirmed by 6 short beeps
and after that the motor will vibrate, meaning that the programming was successful.
The programming on the channel
!!! CAUTION!!
When programming, only the tubular motor which is to be programmed
needs to be power supplied.
2
After the programming procedure is finished You need to verify the directions on the
remote by simply starting the motor. If the directions are swapped then the programming
procedure needs to be done once more, eg:
If the motor has been programmed using the procedure two times P2 and then DOWN
button and the directions are swapped, then we need to program the motor again using
the opposite procedure, meaning two times P2 and then UP button.
ON
P2 MODE
TIME
P2 MODE
TIME
ON
P2 MODE
TIME
P2 MODE
TIME
man auto
man auto

!!!
3
Deleting a channel
Set the channel that You wish to delete.
1.Press P2 button, the motor will emit a single sound and will vibrate.
2.Press the STOP button. The motor will emit a single sound again.
3.Press again P2 button. The deleting procedure will be confirmed by 4 short beeps and
after that the motor will vibrate, meaning that the deleting was successful.
P2 MODE
TIME
P2 MODE
TIME
P2 MODE
TIME
P2 MODE
TIME
CAUTION !!!
If the settings of one channel will be deleted then all the motors that have
been programmed on this channel will be deleted as well. Each deleting
and further programming procedure requires the power to be switched
on for each motor individually, that is why it is recommended that each
motor has its own power supply separately assigned.
Adding another transmitter/channel
The procedure of adding a new transmitter/channel starts with the already working
transmitter. When adding a new transmitter/channel the power supply does not need to
be switched off and on again.
Set the channel that You want to add on a new transmitter.
1.Press P2 button on the already existing transmitter, the motor will emit a single sound
and will vibrate.
2.Press the P2 button again. The motor will only emit a single sound.
3.Now select the transmitter/channel on the new device and press P2 button ( or Up +
STOP buttons simultaneously, depending on the transmitter ). The motor confirms by
emitting 5 short sounds. The new channel/transmitter is programmed.
man auto
Su Mo Tu We Th Fr Sag
auto
12345

4. Device functions:
The transmitter can work in 3 different modes:
MAN – manual mode – only manual control is possible
AUTO – automatic mode – both manual and automatic functions are active
– holiday mode – manual control is possible but the timing functions set
differ randomly by +- 15 minutes
MODE SWITCHING:
In order to switch the working mode of each device You need to Press the MODE button
for more than 2 seconds.
ACTIVE CHANNEL:
Using the buttons CHANNEL +/- we set the actual channel. If a particular channel is
selected, it’s number appears on the display
4
MAN
AUTO
HOLIDAY
man auto
Active
channel
P2 MODE
TIME
DEACTIVATING A CHANNEL:
In AUTO mode there is a possibility to deactivate a particular channel. When a
channel is deactivated the timer functions are switched off. In order to do so select
an active channel and push the P2 button for 1 second (the channel number starts
to blink ). Further pressing the P2 button for 1 second activates the channel again.

TIME/HOUR SETTING:
In order to change the hour/date follow the below instructions:
1.Using the MODE button switch into MAN mode ( pressing it for 2 seconds changes
the mode )
2.Press the TIME button for 5 seconds -> the hour parameter starts to blink on the
screen.
3.Using the buttons UP/DOWN set the hour
4.After setting the hour press the TIME button again to switch into minutes setting
5.Using the buttons UP/DOWN set the minutes
6.After setting all the data confirm by pressing the TIME button for 5 seconds to
memorize the new settings
man
man
P2 MODE
TIME
P2 MODE
TIME
(5 sec.)
P2 MODE
TIME
P2 MODE
TIME
(5 sec.)

SETTING THE TIMER:
In order to set the switching times on each channel follow the below instructions:
1.Using the MODE button switch into AUTO mode ( pressing it for 2 seconds changes
the mode )
2.Select the channel that you want to set and press the TIME button for 5 seconds ->
the switching time UP for channel 1 appears on the screen
3.Using the UP & DOWN buttons set the hour
4.Next press the TIME button to enter the minutes setting and again using UP & DOWN
buttons set the minutes
5.After setting the parameters for switching time UP, press the MODE button to continue
setting the parameters for switching time DOWN.
6.After setting all the parameters for switching times for particular channel, press the
TIME button for 5 seconds in order to memorize the settings
The RR-5 T transmitter has the possibility to program 2 switching times on each channel
individually
For each channel the difference between switching times must be minimum 32 minutes.
There is no possibility to set a switching time on the common channel ( 0 ).
man
man
P2 MODE
TIME
P2 MODE
TIME
(5 sec.)
P2 MODE
TIME
P2 MODE
TIME
(5 sec.)