Poulan Pro 532402341 User manual

03021
• Assembly
• Operation
• Customer Responsibilities
• Repair Parts
532402341 11.02.05 rad
Printed in U.S.A.
OWNER’S MANUAL
Model GTT348
Mfg. ID No. 96072000900
Product No. 960 72 00-09
48 Inch Mower
Grass Catcher

2
I. GENERAL OPERATION
• Read, understand, and follow all instructions on the machine
and in the manual before starting.
• Do not put hands or feet near rotating parts or under the
machine. Keep clear of the discharge opening at all times.
• Only allow responsible adults, who are familiar with the
instructions, to operate the machine.
• Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blades.
• Be sure the area is clear of bystanders before operating.
Stop machine if anyone enters the area.
• Never carry passengers.
• Do not mow in reverse unless absolutely necessary. Always
look down and behind before and while backing.
• Never direct discharged material toward anyone. Avoid
discharging material against a wall or obstruction. Material
may ricochet back toward the operator.Stop the blades when
crossing gravel surfaces.
• Do not operate machine without the entire grass catcher,
discharge guard, or other safety devices in place and work-
ing.
• Slow down before turning.
• Never leave a running machine unattended. Always turn
off blades, set parking brake, stop engine, and remove keys
before dismounting.
• Disengage blades when not mowing. Shut off engine and
wait for all parts to come to a complete stop before cleaning
the machine, removing the grass catcher, or unclogging the
discharge guard.
• Operate machine only in daylight or good artificial light.
• Do not operate the machine while under the influence of
alcohol or drugs.
• Watch for traffic when operating near or crossing road-
ways.
• Use extra care when loading or unloading the machine into
a trailer or truck.
• Always wear eye protection when operating machine.
SAFETY RULES
Safe Operation Practices for Ride-On Mowers
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE
TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
WARNING: In order to prevent ac-
cidental starting when setting up,
transporting, adjusting or making re-
pairs, always disconnect spark plug
wire and place wire where it cannot
contact spark plug.
WARNING: Do not coast down a hill
in neutral, you may lose control of the
tractor.
WARNING: Tow only the attachments
that are recommended by and com-
ply with specifications of the manu-
facturer of your tractor. Use common
sense when towing. Operate only at
the lowest possible speed when on a
slope. Too heavy of a load, while on
a slope, is dangerous. Tires can lose
tractionwiththegroundandcauseyou
to lose control of your tractor.
• Data indicates that operators, age 60 years and above, are
involvedina large percentageof ridingmower-relatedinjuries.
These operators should evaluate their ability to operate the
riding mower safely enough to protect themselves and others
from serious injury.
• Followthemanufacturer'srecommendationfor wheelweights
or counterweights.
• Keep machine free of grass , leaves or other debris
build-up which can touch hot exhaust/engine parts
and burn. Do not allow the mower deck to plow leaves
or other debris which can cause build-up to oc-
cur. Clean any oil or fuel spillage before operating or
storing the machine. Allow machine to cool before
storage.
II. SLOPE OPERATION
Slopes are a major factor related to loss of control and tip-over
accidents, which can result in severe injury or death. Operation
on all slopes requires extra caution. If you cannot back up the
slope or if you feel uneasy on it, do not mow it.
• Mow up and down slopes, not across.
• Watch for holes, ruts, bumps, rocks, or other hidden objects.
Uneven terrain could overturn the machine. Tall grass can
hide obstacles.
• Choose a low ground speed so that you will not have to stop
or shift while on the slope.
• Do not mow on wet grass. Tires may lose traction.
Always keep the machine in gear when going down slopes.
Do not shift to neutral and coast downhill.
• Avoid starting, stopping, or turning on a slope. If the tires lose
traction, disengage the blades and proceed slowly straight
down the slope.
• Keep all movement on the slopes slow and gradual. Do not
make sudden changes in speed or direction, which could
cause the machine to roll over.
• Use extra care while operating machine with grass catch-
ers or other attachments; they can affect the stability of the
machine. Do no use on steep slopes.
• Do not try to stabilize the machine by putting your foot on
the ground.
• Do not mow near drop-offs, ditches, or embankments. The
machine could suddenly roll over if a wheel is over the edge
or if the edge caves in.
III. CHILDREN
Tragic accidents can occur if the operator is not alert to the pres-
ence of children. Children are often attracted to the machine
and the mowing activity. Never assume that children will remain
where you last saw them.
• Keep children out of the mowing area and in the watchful
care of a responsible adult other than the operator.
• Be alert and turn machine off if a child enters the area.
• Before and while backing, look behind and down for small
children.
• Never carry children, even with the blades shut off. They may
fall off and be seriously injured or interfere with safe machine
operation. Children who have been given rides in the past
may suddenly appear in the mowing area for another ride
and be run over or backed over by the machine.
• Never allow children to operate the machine.
• Use extra care when approaching blind corners, shrubs,
trees, or other objects that may block your view of a child.

3
CUSTOMER RESPONSIBILITIES................................. 9
STORAGE ...................................................................... 9
REPAIR PARTS.......................................................10-11
SAFETY RULES .........................................................2-3
CARTON CONTENTS.................................................... 4
ASSEMBLY.................................................................5-7
OPERATION .................................................................. 8
TABLE OF CONTENTS
CONGRATULATIONS on your purchase of a new Grass Catcher. It has been designed, engineered and manufactured to
give you the best possible dependability and performance.
Should you experience any problems you cannot easily remedy, please contact your nearest authorized service center/
department. They have competent, well trained technicians and the proper tools to service or repair this unit.
Please read and retain this manual.The instructions will enable you to assemble and maintain your Grass Catcher properly.
Always observe the "SAFETY RULES".
• Be sure the area is clear of bystanders before operat-
ing. Stop machine if anyone enters the area.
• Never carry passengers.
• Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while back-
ing.
• Nevercarrychildren, evenwith thebladesshut off. They
may fall off and be seriously injured or interfere with
safe machine operation.Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
• Keepchildrenoutofthemowingareaandinthewatchful
care of a responsible adult other than the operator.
• Be alert and turn machine off if a child enters the
area.
• Before and while backing, look behind and down for
small children.
• Mow up and down slopes (15° Max), not across.
• Be alert and turn machine off if a child enters the
area.
• Choose a low ground speed so that you will not have
to stop or shift while on the slope.
• Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope.
• If machine stops while going uphill, disengage blades,
shift into reverse and back down slowly.
• Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.
SAFETY RULES
Safe Operation Practices for Ride-On Mowers
IV. TOWING
• Tow only with a machine that has a hitch designed for towing.
Do not attach towed equipment except at the hitch point.
• Follow the manufacturer's recommendation for weight limits
for towed equipment and towing on slopes.
• Never allow children or others in or on towed equipment.
• On slopes, the weight of the towed equipment may cause
loss of traction and loss of control.
• Travel slowly and allow extra distance to stop.
V. SERVICE
SAFE HANDLING OF GASOLINE
To avoid personal injury or property damage, use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive.
• Extinguish all cigarettes, cigars, pipes, and other sources of
ignition.
• Use only approved gasoline container.
• Never remove gas cap or add fuel with the engine running.
Allow engine to cool before refueling.
• Never fuel the machine indoors.
• Never store the machine or fuel container where there is an
open flame, spark, or pilot light such as on a water heater
or other appliances.
• Never fill containers inside a vehicle or on a truck or trailer
bed with plastic liner. Always place containers on the ground
away from your vehicle when filling.
• Remove gas-powered equipment from the truck or trailer
and refuel it on the ground. If this is not possible, then refuel
such equipment with a portable container, rather than from
a gasoline dispenser nozzle.
• Keep the nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete. Do
not use a nozzle lock-open device.
• If fuel is spilled on clothing, change clothing immediately.
• Never overfill fuel tank. Replace gas cap and tighten se-
curely.
GENERAL SERVICE
• Never operate machine in a closed are.
• Keep all nuts and bolts tight to be sure the equipment is in
safe working condition.
• Never tamper with safety devices. Check their proper opera-
tion regularly.
• Keep machine free of grass, leaves, or other debris build-up.
Clean oil or fuel spillage and remove any fuel-soaked debris.
Allow machine to cool before storing.
• If you strike a foreign object, stop and inspect the machine.
Repair, if necessary, before restarting.
• Never make any adjustments or repairs with the engine run-
ning.
• Check grass catcher components and the discharge guard
frequently and replace with manufacturer's recommended
parts, when necessary.
• Mower blades are sharp. Wrap the blade or wear gloves,
and use extra caution when servicing them.
• Check brake operation frequently. Adjust and service as
required.
• Maintain or replace safety and instruction labels, as neces-
sary.

4
CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR:
• Depress clutch/brake pedal fully and set parking brake.
• Place gearshift/motion control lever in "NEUTRAL" position.
• Place attachment clutch in "DISENGAGED" position.
• Turn ignition key "OFF" and remove key.
• Make sure the blade and all moving parts have completely stopped.
• Disconnect spark plug wire from spark plug and place wire where it cannot come in contact
with plug.
NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the
tractor, in the operator's position.
KNOW YOUR GRASS CATCHER
READTHISOWNER'SMANUAL AND SAFETYRULES BEFORE ASSEMBLING OR OPERATINGYOURGRASS CATCHER.
Compare the illustrations with the carton contents to familiarize yourself with the parts before starting the assembly. Study
the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to
prevent injury to yourself and others. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the eyes,
which can result in severe eye damage. Always wear safety glasses or eye shields
before starting your tractor and while mowing. We recommend a wide vision safety
mask for over the spectacles or standard safety glasses.
03021
LOWER CHUTE
ATTACHING
STRAPS
PARTS IDENTIFICATION
UPPER CHUTE
CHUTE LATCH
FULL
BAG
INDICATOR
LOWER CHUTE
GRASS
CATCHER
CONTAINERS
COVER
ASSEMBLY
UNPACKING INSTRUCTIONS
• Remove all parts and packing materials from carton.
• Check carton contents against list. Be sure all parts
are there.
CARTON CONTENTS:
(3) Container Tops
(3) Container Bottoms
(1) Upper Chute
(1) Lower Chute
(1) Cover Assembly
RETAINER
SPRING
SUPPORT
ASSEMBLY
Marked "A" SUPPORT
ASSEMBLY
Marked "B"

5
1
BAGGER SUPPORT ASSEMBLY
(See Fig. 1)
Determine the correct support assembly for your tractor.
The support assemblies are marked "A" and "B".
Compare the drawbar illustrations below to the drawbar
located at the rear of your tractor.
Use the support assembly indicated for your tractor and
discard the other support assembly.
2
FIG. 1
MOUNTING COVER ASSEMBLY TO
SUPPORT ASSEMBLY (See Fig. 2)
NOTE: For ease of assembly, you may wish to obtain the
assistance of another person for mounting cover assembly
to tractor.
1. Position cover assembly on ground behind tractor.
2. Liftand rotate coverto aligncover brackets with support
assembly tubes.
3. Slide cover assembly down onto the support tubes.
FIG. 2
03024
COVER
ASSEMBLY
SUPPORT
ASSEMBLY
ASSEMBLY
1. Slide flanges of support assembly into drawbar slots
first, then, pivot backwards inserting pin into drawbar
pin hole.
2. Be sure support assembly is seated properly, then
secure with retainer spring.
DRAWBAR A
Use Support Assembly
Marked "A"
DRAWBAR B
Use Support Assembly
Marked "B"
02543
INSERT
FLANGES
FIRST INTO
DRAWBAR
SLOTS
SUPPORT
ASSEMBLY
DRAWBAR SLOTS
RETAINER
SPRING
PIN
02051
02051
02051
DRAWBAR
PIN HOLE

6
WARNING
Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris
subjecttowearanddetierioration.Checkbagfrequently.Re
placewhen
crackedordamaged.Useonlyarecommendedreplacementcontainer.
WARNING
Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris
subjecttowearanddetierioration.Checkbagfrequently.Replacewhen
crackedordamaged.Useonlyarecommendedreplacementcontainer.
03022
CONTAINER MOUNTING (See Fig. 4)
1. Install one container to left side first with warning to
outside of unit. Install another container to center
position and one in right position.
NOTE:Right container should always overlap left container
at center supports.
2. Close cover and lock latch handles over center support
tubes.
4
FIG. 4
COVER LATCH
HANDLES
CONTAINER
WARNING
CONTAINER
HANDLE
CONTAINER
WARNING
CENTER
SUPPORT
TUBES
CONTAINER ASSEMBLY (See Fig. 3)
1. Place bottom half inside of top half, as shown.
2. Place one foot inside bottom half and lift top half to
meet bottom half.
3. Press halves tightly together while lifting top to lock
into place as shown.
IMPORTANT:BEFORE LOCKINGTHETABS,HOOKED EDGES
ONBOTHHALVESMUSTOVERLAPTOFORMSEALASSHOWN
IN INSET.
4. Repeat for other containers.
PRESS TOGETHER
TO FORM SEAL
WHILE LIFTING
TOP HALF
02089
CONTAINER
BOTTOM
HALF
CONTAINER
TOP HALF
ASSEMBLY CHECK: Squeeze sides of lower half of con-
tainer and check that there is no gap between upper and
lower halves. If a gap appears, unlock tabs to separate
container halves and repeat instructions above.
LOCKING
TAB
WARNING
Donotoperatemowerunlesscontainerisprope
rlyissubjecttowearanddetierioration.Checkbagfrequ
ently.Replacewhencrackedordamaged.Useonlyarecomme
ndedreplacementcontainer.
02097
FIG. 3
3
02739
CONTAINER
BOTTOM HALF
CONTAINER
TOP HALF

7
02552
LOWER CHUTE (See Fig. 5)
1. Raise and hold deflector shield in upright position.
2. Placeslotin lowerchuteovertab on mowerandposition
lower chute over mower opening as shown.
3. Hook rear latch into flange hole on back of mower.
4. Hook front latch into tab hole on front of mower.
5
CAUTION: Do not remove deflector
shield from mower. Raise and hold
shield when attaching lower chute
and allow it to rest on chute while in
operation.
REAR LATCH
FRONT
LATCH
DEFLECTOR
SHIELD
FIG. 5
03029
UPPER CHUTE (See Figs. 6A & 6B)
1. Lower mower to its lowest cutting position.
2. Assemble upper chute by inserting curved end into
hole in back of cover.
NOTE: Handle carefully so as not to damage full bagger
indicator.
3. Push in and turn upper chute until it is in line with lower
chute.
4. Align the bosses on lower chute with alignment slots
on upper chute and slide together.
5. Secure with rubber latch by hooking hole in latch over
latch pin.
6
COVER HANDLE
LOWER
CHUTE
FULL BAGGER
INDICATOR
UPPER
CHUTE
FIG. 6B
FIG. 6A
03023
BOSSES
LATCH PIN
ALIGNMENT
SLOT
RUBBER
LATCH
LEVEL MOWER
• Be sure mower is properly leveled for best mower
performance. See your tractors owner's manual for
instructions
7
TAB
OPTIONAL FRONT
GAUGE WHEEL

8
TIPS FOR IMPROVED BAGGING
OPERATION:
Follow the mower operation instructions in your tractor
owner's manual.
When operating your grass catcher on a lawn where grass
and leaf bagging equipment has not been used, you are
picking up thatch and debris that has accumulated for long
periods of time. The amount collected and the total time
of operation may be greater than you will experience with
regular use of your grass catcher.
• Always run throttle at full speed when bagging.
• Select a gear low enough to give good mower cutting
performance, good quality cut and good bagging
performance.
NOTE: It may be necessary to overlap width of cut to suit
your conditions.
• If grass is extremely tall, it should be mowed twice.The
first time relatively high, the second time to desired
height.
• Use left hand side of mower for trimming.
• Plastic trash bags can be inserted inside grass catcher
containers for ease of debris disposal. To remove the
plastic trash bags when full:
a. Disengage blades, shift into neutral, engage the
parking brake and stop the engine.
b. Raise seat. Unlatch and raise cover.
c. Remove one container at a time by grasping
container handles and pulling toward the rear, off
of the tube rails.
d. With the container resting on the ground, close
and secure the top of the plastic lawn bag.
e. Tip the container on its side and slide the filled bag
from the container.
f. Install a new plastic lawn bag with the edges of the
bag draped over upper lip of the container.
g. Repeat for other containers.
h. Reinstall containers making sure right container
overlaps left container at center supports.
j. Closecoverandsecure latches overcenter support
tubes.
• Avoid cutting wet grass or in the morning while the dew
is still heavy. Grass clippings collected under these
conditions tend to be sticky and adhere to the walls of
the flow path causing clogging.
• Your bagger is equipped with a full bagger indicator.
Movement of the wheel increases as the bags fill.The
wheel will be spinning fastest just before the bags fill
completely.When the wheel stops, it indicates that the
bags are full and the chutes have become clogged.
NOTE: To help prevent clogging of chutes, check/empty
bags when the wheel is spinning fast.Experience will teach
you the best time to empty the bags.
Care should be taken not to damage the parts and that
the wheel spins freely at the beginning of each use.
• If the grass catcher fails to pick up cut grass or leaves,
it is an indication that clogging has occurred in the
system or that the grass catcher containers are full.
Usually this is indicated by the stopped movement of
the full bagger indicator.
a. Disengage blades, shift into neutral, engage the
parking brake and stop the engine.
- Raise seat. Unlatch and raise cover.
- Slide out containers and dispose of clippings .
- Replace containers, close cover, and latch.
b. Unlatch chutes and check for clogging.
- Remove all debris in chutes.
- Reassemble and latch chutes
c. Checkto insurefullbaggerindicatorhasnotbecome
clogged.
- The air passage hole must be clear of debris.
Gentlyinserta small twig orwireintopassageway
to clear.
CAUTION
• Do not operate mower with grass catcher
partially installed.
• Disengage blades and stop engine before
leaving tractor seat to empty containers,
unclogging chutes, etc.
• Close cover before starting.
• Disengage mower when crossing driveways
or gravel surfaces and other areas where
thrown objects could be a hazard.
• Do not attempt to vacuum up cans or other
potentially hazardous projectiles.
OPERATION

9
STORAGE
When grass catcher is to be stored for a period of time,
clean it thoroughly, remove all dirt, grass, leaves, etc.Store
in a clean, dry place.
CAUTION: Do notleavegrassinbagger
containers. Emptycontainersaftereach
use and before storing. Failure to do so
mayresult inspontaneouscombustion
which could develop into a fire.
GENERAL RECOMMENDATIONS
Always observe safety rules when performing any main-
tenance.
• Before each use check for loose fasteners.
• Clean unit thoroughly after each use.
BLADE CARE
For best results mower blades must be kept sharp. Replace
bent or damaged blades.
• See BLADE CARE instructions in your tractor owner's
manual.
CAUTION:BEFOREPERFORMINGANY
MAINTENANCE,SERVICE OR ADJUST-
MENTS:
• Depress clutch brake pedal fully and
set parking brake.
• Place gearshift/motion control lever in
"NEUTRAL" position.
• Place clutch control in "DISENGAGED"
position.
• Turn ignition key to "OFF" position.
• Make sure blades and all moving parts
have completely stopped.
• Disconnect spark plug wire(s) from
spark plug(s) and place wire where it
cannot come in contact with plug.
CAUTION: Grass catcher components
are subject to wear, damage and
deterioration, which could expose
moving parts or allow objects to be
thrown. Frequently check components
and replace with manufacturer's
recommended parts, when necessary.
CUSTOMER RESPONSIBILITIES

10
WARNING
Donot operatemowerunlesscontainer isproperlyisnstalled.Container is
subjecttowearanddetierioration. Checkbagfrequently. Replacewhen
crackedor damaged. Useonlyarecommendedreplacement container.
WARNING
Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris
subjecttowearand detierioration.Checkbagfrequently.Replace when
crackedordamaged.Useonlyarecommendedreplacementcontainer.
35
27
36
WARNING
Donotoperatemowerunlesscontainerisproperlyis nstalled.Containeris
subjecttowearanddetierioration.Checkbagfrequently.Replacewhen
crackedordamaged.Useonlyarecommendedreplacementcontainer.
28
33
32
26
31
31
33
20
9
12
13
14
18
5
8
9
10
11
20
9
12
16
15
16
14
6
7
15
3
4
2
34
37
20
38
38
20
2
REPAIR PARTS/PIÈCES DE RECHANGE
GRASS CATCHER - MODEL GTT348 (MFG. ID 96072000900) / RAMASSE-HERBE - MODÈLE GTT348 (MFG ID 96072000900)
PRODUCT NUMBER 960 72 00-09 / NO. DE PRODUIT 960 72 00-09

11
KEY PART DESCRIPTION
NO. NO.
KEY PART DESCRIPTION
NO. NO.
2 532069180 Nut, Crownlock #10-24 Écrou auto-serrant #10-24
3 532192709 Screen, Cover Écran de couvercle
4 532195373 Cover Assembly Couvercle
(Includes Key No. 34, 37) (Y compris 3, 37,38,39)
5 532176741 Chute, Upper Glissière supérieure
6 818021008 Screw, Special #10-14x1/2 Vis spéciale #10-14x1/2
7 532130933 Full bag Indicator Indicateur de sac plein
8 532087175 Screw, #10-24 x 1-1/8 Vis #10-24 x 1-1/8
9 819061216 Washer 3/16x3/4x16 Ga. Rondelle 3/16x3/4x16 Ja.
10 532007206 Spacer, Split Entretoise fendue
11 532060867 Nut, Acorn #10-24 Écrou borgne #10-24
12 810071000 Washer, lock Rondelle frein
13 532109808 Latch, Chute Loquet de glissière
14 532125004 Nut, Weld Axe de loquet
15 532130760 Latch, Hook Crochet de loquet
16 532130759 Rubber, Latch Loquet de caoutchoc
18 532174345 Chute, Lower Glissière inférieure
20 871161010 Screw #10-24 x 5/8 Vis #10-24 x 5/8
26 532124670 Spring, Retainer Ressort de retenue
27 532176987 Support Assembly "A" Ensemble du support "A"
532198128 Support Assembly "B" Ensemble du support "B"
28 532165898 Spring, Retainer Ressort de retenue
31 532174083 Plug, Tubing End Capuchon d’extrémité de tuyau
32 532176990 Bagger, Frame Cadre de ramasse-herbe
33 532192786 Pin, Hinge Goupille de charnière
34 532192550 Gasket, Cover Garniture de couvercle
35 532183286 Container, Top Bac à gazon supérieur
36 532129586 Container, Bottom Bac à gazon inférieur
37 532192603 Ring, Cover Gasket Anneau de garniture decouvercle
38 532130895 Latch Handle, Cover Poignée de loquet de couve
— 532402341 Owner's Manual Manuel de propriétaire
REPAIR PARTS
GRASS CATCHER - MODEL GTT348 (MFG. ID 96072000900) / RAMASSE-HERBE - MODÈLE GTT348 (MFG ID 96072000900)
PRODUCT NUMBER 960 72 00-09 / NO. DE PRODUIT 960 72 00-09