Powell BriteSpot Fiber-Opc User manual

1- Mounng Fixture and Opcal Fiber Installaon
Required for Installaon
A - Secure the Mounng Fixture to Busbar and Connect Fiber
Tools for Fiber Mounng:
Adjustable Wrench
1.5 mm Allen Key
Guillone Cuer
Components for Hardware Installaon:
B - Route the Fiber to Low-Voltage Cabinet
I. Insert the screw with the washer through the
fixture and busbar.
II. Insert the washers and secure it with a nut.
Ensure the hole for fiber inseron is pointed in
the direcon of the fiber roung.
Installaon of the BriteSpot Fiber-Opc Temperature Sensor has been engineered to be simple and straighorward. The
following manual will describe in detail the 3 steps needed for installaon. No specialized knowledge of fiber opcs is
necessary. A basic understanding of switchgear topology and mounng methods is required.
35 mm DIN rail (6"-8") and mounng
hardware
CAT5 Ethernet cable (if connecng to SCADA or
computer.
Quick Start Guide
G3
BriteSpot
Temperature Monitoring
Powell Canada Inc,
Suite 201, 55 Gosck Place
North Vancouver, BC, V7M 3N2
- MAX 100ºC
Sensor Tip - MAX 120ºC
Fiber
R
Do NOT bend fiber ghter
than 12 mm (1/2") radius
Do not fasten or aach ANY
mounng hardware (e-wraps,
etc.) to at least a 30 cm (12")
length of fiber between the
poron of the probe at high
v o l t a g e a n d i t s fi r s t n o n -
energized point of contact.
Keep away from sources of
excessive heat when ever
possible. Fiber probe shall not
be aached to surfaces with
temp e rat u res exc e eding
100ºC or 200ºF.
! !
Voltage: 12-24 VDC (0.12A@24VDC)
Power: 3 Was (Max)
Power Supply Requirements:
III. Insert fiber into the holding fixture and secure it
with a 1.5 mm hex screwdriver.
Avoid running fibers In the
direcon of the fold of the boot to
minimize bending and damage of
the fiber.
!

B - Insert the Opcal Fibers
2 - Hardware Installaon
D - Typical Network Connecons
C - Connect Network and Power Wiring
Star Topology (Ethernet)
Typical Serial Topology (MODBUS RTU)
(within cabinet) or connecng with twisted pair cables (cabinet to cabinet)
I. Loosen the connectors by
screwing them counter
clockwise.
A - Mount on 35 mm DIN Rail
Installing Removing
1
2
Input Voltage
Negave
Input Voltage
Negave
Input Voltage Posive Input Voltage Posive
Inverng, 2-wire, RS-
485 Chassis Grounding
Non-Inverng, 2-wire,
RS-485
Shielding of
Communicaon Pair
Relay:
Common Terminal
Relay:
Normally Open
Terminals 1-5 Terminals 6-10
Terminal
Terminal
Number Number
Name Name Funcon Funcon
6V-
V-
Rx-
Shd
7 V+
V+
Tx+
8PE
9COM
10 NO
1
2
3
4
5
6 7 8 9 10
1 2 3 4 5
10/100
STAT
RST ID#:
BriteSpot
G3
BS3
BS2
BS1
LINK
COM
SYS
4 5 6
7 8 9
1 2 3
10/100
STAT
RST ID#:
BriteSpot
G3
BS3
BS2
BS1
LINK
COM
SYS
4 5 6
7 8 9
1 2 3
HMI PLC G3 Slave Device 1-31
10/100
STAT
RST ID#:
BriteSpot
G3
BS3
BS2
BS1
LINK
COM
SYS
4 5 6
7 8 9
1 2 3
10/100
STAT
RST ID#:
BriteSpot
G3
BS3
BS2
BS1
LINK
COM
SYS
4 5 6
7 8 9
1 2 3
HMI/Master Hub
G3 Slave Devices
1
2
Note that terminals 1 and 6, as well as 2 and 7, are connected internally.
If a light remains red, ensure the probe is inserted
properly and the fiber cut is clean. Recut if necessary.
View LEDs above the connectors to determine if a
connecon has been established.
BS3
BS2
BS1
7 8
1
III. Secure fiber retenon nuts
by screwing them clockwise.
BS3
BS2
BS1
4
7 8
1
BS3
BS2
BS1
4
7 8 9
1
II. Insert the opcal fibers
unl they come to a hard
stop. Do NOT apply excessive
force.
Quick Start Guide
G3
BriteSpot
Temperature Monitoring
Powell Canada Inc,
Suite 201, 55 Gosck Place
North Vancouver, BC, V7M 3N2
Wiring Interface

3 - Configure the Communicaon Sengs
A - Connect to the Device
B - Factory Reset
I.
Connect a CAT5 Ethernet Cable directly
between the Ethernet ports on the
router and G3 to be configured.
II.
Ensure the power is connected to the
device and a link is established, indicated
by the LEDs.
III.
Type in the IP address in the browser
(default: 192.168.1.50). A field has been
provided on the back scker in case it has
been changed
IV.
From the home page you can navigate
throughout the rest of the site by using
the navigaon bar on the le.
To perform a factory reset:
I. Insert an object, such as the end of a probe, into the hole labelled "RST" in the
top le corner of the device and depress the concealed buon while applying
power to the device. Keep the buon depressed unl both the "SYS" and "COM"
LEDs stay green (about 5 seconds).
II. Release the buon and the device will restart with its default values.
Quick Start Guide
G3
BriteSpot
Temperature Monitoring
Powell Canada Inc,
Suite 201, 55 Gosck Place
North Vancouver, BC, V7M 3N2
Note that if connecng via Ethernet to a computer directly, the Internet Protocol Version 4 IP address must be set in the
network seng on the computer.
The first 3 numbers (separated by periods) of the Internet Protocol Version 4 IP address
should match that of the BSG3 being used, while the last number remains different. For
example, if the BSG3 IP address is the default 192.168.1.50, the Internet Protocol
Version 4 IP address can be set to 192.168.1.3.
To do this, open Network and Sharing Center on the computer. Open the Ethernet
Connecon (or Local Area Connecon) labelled “Unidenfied network”, then
open Properes. From the List, select Internet Protocol Version 4 and then click
Properes, where the IP address can be set.

PRESS BOTH BUTTONS
AT THE SAME TIME
1
SCROLL UP UNTIL THE
STAR IS PLACED ON
THE LEFT SIDE OF THE
UPPER TITLE
2
USE UP AND DOWN BUTTONS TO SCROLL
U P A N D DO W N T H R O U G H T H E
DIFFERENT SCREENS
USE UP AND DOWN BUTTONS TO SCROLL
UP AND DOWN THROUGH THE DIFFERENT
SCREEN PARAMETERS
USE UP AND DOWN BUTTONS TO MODIFY
THE SELECTED PARAMETER
UPPER LEVEL MENU SUBMENU PARAMETER
MODIFICATION
* DEVICE PARAMETERS
DEGREE: C
LOG RATE: 1 MIN
MOD PORT: 502
SLAVE ID: 7
BAUD: 19200
* IP PARAMETERS
MAC A4:3B:FA:24:93:E2
GATE 169.254. 1. 1
MASK 255.255. 0. 0
IP 169.254. 1. 1
* TEMPERATURE ( C )
25 27 24
25 26 24
28 24 22
* BSG3.9S INFO
FW: 30036:0.00.21
HW: 10121
S/N: 300002
15:17:11 17/03/2014
DEVICE PARAMETERS
DEGREE: C
LOG RATE: 1 MIN
MOD PORT: 502
SLAVE ID: 7
BAUD: 19200
DEVICE PARAMETERS
DEGREE: C
LOG RATE: 1 MIN
MOD PORT: 502
SLAVE ID: 7
BAUD: 19200
*
>
1
21
* FIBER POWER
0 9 0
9 9 9
0 9 0
* ALARM STATUS
- E -
A - W
- - -
* BRITEALERT
STATUS: WARNING
ERROR NUM 1
01 05
* ALERT CONFIG
SOUND: OFF
* SET THRESHOLD (C)
WARNING: 90
ALARM: 105
BRITEALERT
STATUS: WARNING
*ERROR NUM 1
01 05
1
2
BRITEALERT
STATUS: WARNING
>ERROR NUM 1
01 05
ALERT CONFIG
*SOUND: OFF
1
2
ALERT CONFIG
>SOUND: ON
SET THRESHOLD (C)
WARNING: 90
*ALARM: 105
SET THRESHOLD (C)
WARNING: 90
>ALARM: 105
1
2
Quick Start Guide
The BSG3 is equipped with a simple LCD display and a set of buons which allow for navigaon as well as basic data display and
configuraon as shown below.
Navigaon Map
G3
BriteSpot
Temperature Monitoring
Powell Canada Inc,
Suite 201, 55 Gosck Place
North Vancouver, BC, V7M 3N2