Power-Pole Fob-CM1 Installation manual

Remote Control Transmitter Fob-CM1
Programming Instructions
Pairing Key-Fob Remote Control:
1. Press and hold the PROGRAM button on the top of the
unit for 3 seconds until the LED turns green (HPU will also
beep). The unit is now ready to be paired with the key-fob
remote control.
NOTE: If dual units are installed, repeat Steps 1–3 to pair
multiple units to a single remote control. Up to (10)
wireless controllers can be programmed to each unit.
2. Press the UP button on the key-fob remote control for one
second and release. The green LED on the unit(s) will
initially turn off, then flash green steadily (HPU will also
beep) indicating that the pairing is complete.
3. Test the paired remote control by pressing the UP
and the DOWN button to ensure that the anchor
is responding.
PROGRAM LED
Hydraulic Pump Unit (HPU) MICRO Driver Unit
LED
PROGRAM
2
9010 Palm River Road, Tampa, FL 33619
phone [phone] • fax [phone]
www.power-pole.com
Need help? Contact our Technical Support Team at
1 + 813.689.9932 Option 2
©2018 all rights reserved. Power-Pole Shallow Water Anchor
U.S. Patent No. 6,041,730
To raise or lower the spike, press and hold either the UP or
DOWN button on the remote control. The anchor will only
continue to move so long as you keep the button depressed.
Auto Mode: Double tapping (pressing and releasing 2 times
within 1 second) either the UP or the DOWN buttonon the
remote control will cause the anchor to retract or deploy au-
tomatically. The anchor will continue to move in said direction
until it either retracts completely (up) or senses a solid bottom
surface (down).
Battery Replacement:
1. Ensure the surrounding area is as dry as possible to avoid
any moisture intrusion.
2. Use a small screwdriver to remove the Key-Fob cover. (FIG. 1)
3. Remove the rubber membrane and the circuit board from
the Key-Fob.
4. Remove the battery from the holder on the front of circuit
board and replace with any CR2032 3V Lithium Coin
Battery. (FIG. 2)
5. Place the circuit board and rubber membrane back into
the Key-Fob base and ensure that the rubber membrane
is seated properly prior to installing the cover. (FIG. 3)
Operating Instructions
For Technical Support Call 813.689.9932 option 2
Programming Instructions
Key Fob Remote Control
Featuring Technology
Pairing Key-Fob Remote Control:
1. Press and hold the PROGRAM button on the top of the
unit for 3 seconds until the LED turns green (HPU will
also beep). The unit is now ready to be paired with the
key-fob remote control.
NOTE: If dual units are installed, repeat Steps 1–3 to pair
multiple units to a single remote control. Up to (10)
wireless controllers can be programmed to each unit.
2. Press the UP button on the key-fob remote control for
one second and release. The green LED on the unit(s)
will initially turn off, then flash green steadily (HPU will
also beep) indicating that the pairing is complete.
3. Test the paired remote control by pressing the UP
and the DOWN button to ensure that the anchor
is responding.
PROGRAM LED
Hydraulic Pump Unit (HPU) MICRO Driver Unit
LED
PROGRAM
To activate your warranty or find a Power-Pole Certified
Warranty Center, go to www.power-pole.com
2
For Technical Support Call 813.689.9932 option 2
9010 Palm River Road, Tampa, FL 33619 • phone [phone]
fax [phone] • www.power-pole.com
To raise or lower the spike, press and hold either the UP or
DOWN button on the remote control. The anchor will only
continue to move so long as you keep the button depressed.
Auto Mode: Double tapping (pressing and releasing 2 times
within 1 second) either the UP or the DOWN button
on the remote control will cause the anchor to retract or
deploy automatically. The anchor will continue to move
in said direction until it either retracts completely (up) or
senses a solid bottom surface (down).
Battery Replacement:
1. Ensure the surrounding area is as dry as possible to avoid
any moisture intrusion.
2. Use a small screwdriver to remove the Key-Fob cover.
(Figure 1)
3. Remove the rubber membrane and the circuit board from
the Key-Fob.
4. Remove the battery from the holder on the front of circuit
board and replace with any CR2032 3V Lithium Coin
Bat tery. (Figure 2)
5. Place the circuit board and rubber membrane back into
the Key-Fob base and ensure that the rubber membrane
is seated properly prior to installing the cover. (Figure 3)
Operating Instructions
Figure 1 Figure 2 Figure 3
For Technical Support Call 813.689.9932 option 2
Programming Instructions
Key Fob Remote Control
Featuring Technology
Pairing Key-Fob Remote Control:
1. Press and hold the PROGRAM button on the top of the
unit for 3 seconds until the LED turns green (HPU will
also beep). The unit is now ready to be paired with the
key-fob remote control.
NOTE: If dual units are installed, repeat Steps 1–3 to pair
multiple units to a single remote control. Up to (10)
wireless controllers can be programmed to each unit.
2. Press the UP button on the key-fob remote control for
one second and release. The green LED on the unit(s)
will initially turn off, then flash green steadily (HPU will
also beep) indicating that the pairing is complete.
3. Test the paired remote control by pressing the UP
and the DOWN button to ensure that the anchor
is responding.
PROGRAM LED
Hydraulic Pump Unit (HPU) MICRO Driver Unit
LED
PROGRAM
To activate your warranty or find a Power-Pole Certified
Warranty Center, go to www.power-pole.com
2
For Technical Support Call 813.689.9932 option 2
9010 Palm River Road, Tampa, FL 33619 • phone [phone]
fax [phone] • www.power-pole.com
To raise or lower the spike, press and hold either the UP or
DOWN button on the remote control. The anchor will only
continue to move so long as you keep the button depressed.
Auto Mode: Double tapping (pressing and releasing 2 times
within 1 second) either the UP or the DOWN button
on the remote control will cause the anchor to retract or
deploy automatically. The anchor will continue to move
in said direction until it either retracts completely (up) or
senses a solid bottom surface (down).
Battery Replacement:
1. Ensure the surrounding area is as dry as possible to avoid
any moisture intrusion.
2. Use a small screwdriver to remove the Key-Fob cover.
(Figure 1)
3. Remove the rubber membrane and the circuit board from
the Key-Fob.
4. Remove the battery from the holder on the front of circuit
board and replace with any CR2032 3V Lithium Coin
Bat tery. (Figure 2)
5. Place the circuit board and rubber membrane back into
the Key-Fob base and ensure that the rubber membrane
is seated properly prior to installing the cover. (Figure 3)
Operating Instructions
Figure 1 Figure 2 Figure 3
For Technical Support Call 813.689.9932 option 2
Programming Instructions
Key Fob Remote Control
Featuring Technology
Pairing Key-Fob Remote Control:
1. Press and hold the PROGRAM button on the top of the
unit for 3 seconds until the LED turns green (HPU will
also beep). The unit is now ready to be paired with the
key-fob remote control.
NOTE: If dual units are installed, repeat Steps 1–3 to pair
multiple units to a single remote control. Up to (10)
wireless controllers can be programmed to each unit.
2. Press the UP button on the key-fob remote control for
one second and release. The green LED on the unit(s)
will initially turn off, then flash green steadily (HPU will
also beep) indicating that the pairing is complete.
3. Test the paired remote control by pressing the UP
and the DOWN button to ensure that the anchor
is responding.
PROGRAM LED
Hydraulic Pump Unit (HPU) MICRO Driver Unit
LED
PROGRAM
To activate your warranty or find a Power-Pole Certified
Warranty Center, go to www.power-pole.com
2
For Technical Support Call 813.689.9932 option 2
9010 Palm River Road, Tampa, FL 33619 • phone [phone]
fax [phone] • www.power-pole.com
To raise or lower the spike, press and hold either the UP or
DOWN button on the remote control. The anchor will only
continue to move so long as you keep the button depressed.
Auto Mode: Double tapping (pressing and releasing 2 times
within 1 second) either the UP or the DOWN button
on the remote control will cause the anchor to retract or
deploy automatically. The anchor will continue to move
in said direction until it either retracts completely (up) or
senses a solid bottom surface (down).
Battery Replacement:
1. Ensure the surrounding area is as dry as possible to avoid
any moisture intrusion.
2. Use a small screwdriver to remove the Key-Fob cover.
(Figure 1)
3. Remove the rubber membrane and the circuit board from
the Key-Fob.
4. Remove the battery from the holder on the front of circuit
board and replace with any CR2032 3V Lithium Coin
Bat tery. (Figure 2)
5. Place the circuit board and rubber membrane back into
the Key-Fob base and ensure that the rubber membrane
is seated properly prior to installing the cover. (Figure 3)
Operating Instructions
Figure 1 Figure 2 Figure 3
To activate your warranty or find a Power-Pole Certified Warranty Center,
go to www.power-pole.com

FCC Part 15.19 Warning Statement
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
FCC Part 15.21 Warning Statement
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED
BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY
TO OPERATE THE EQUIPMENT.
IC RSS-GEN, Sec 7.1.3 Warning Statement
ENGLISH: This device complies with Industry Canada license-
exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
FRENCH: Le présent appareil est conforme aux CNR
d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
IC RSS-GEN, Sec 7.1.2 Warning Statement
ENGLISH: Under Industry Canada regulations, this
radio transmitter may only operate using an antenna
of a type and maximum (or lesser) gain approved for
the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than
that necessary for successful communication.
FRENCH: Conformément à la réglementation d’Industrie
Canada, le présent émetteur radio peut fonctionner avec
une antenne d’un type et d’un gain maximal (ou inférieur)
approuvé pour l’émetteur par Industrie Canada. Dans le but
de réduire les risques de brouillage radioélectrique à l’intention
des autres utilisateurs, il faut choisir le type d’antenne et son
gain de sorte que la puissance isotrope rayonnée quivalente
(p.i.r.e.) ne dépassepas l’intensité nécessaire à l’établissement
d’une communication satisfaisante.
IC RSS-102, Sec 2.6 Warning Statements
ENGLISH: The applicant is responsible for providing proper
instructions to the user of the radio device, and any usage
restrictions, including limits of exposure durations. The user
manual shall provide installation and operation instructions,
as well as any special usage conditions, to ensure compliance
with SAR and/or RF field strength limits. For instance,
compliance distance shall be clearly stated in the user manual.
FRENCH: Le mode d’emploi des appareils destinés à
l’utilisation contrôlée doit aussi inclure des informations sur
les caractéristiques de fonctionnement de l’appareil; les
instructions de fonctionnement pour assurer la conformité
avec SAR et / ou les limites d’intensité de champ RF;
informations sur l’installation et l’exploitation d’accessoires
pour assurer le respect des SAR et / ou les limites d’intensité de
champ RF; et les coordonnées où l’utilisateur peut obtenir des
informations sur l’exposition canadienne de radiofréquences
et la conformité. Autres renseignements connexes peuvent
également être inclus.